--- /dev/null
+/*
+ * Copyright (C) 2004 Arabella Software Ltd.
+ * Yuli Barcohen <yuli@arabellasw.com>
+ *
+ * Support for Interphase iSPAN Communications Controllers
+ * (453x and others). Tested on 4532.
+ *
+ * Derived from iSPAN 4539 port (iphase4539) by
+ * Wolfgang Grandegger <wg@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_ISPAN /* ...on one of Interphase iSPAN boards */
+#define CONFIG_CPM2 1 /* Has a CPM2 */
+
+#define CONFIG_SYS_TEXT_BASE 0xFE7A0000
+
+/*-----------------------------------------------------------------------
+ * Select serial console configuration
+ *
+ * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * If CONFIG_CONS_NONE is defined, then the serial console routines must be
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define CONFIG_CONS_ON_SMC /* Define if console on SMC */
+#undef CONFIG_CONS_ON_SCC /* Define if console on SCC */
+#undef CONFIG_CONS_NONE /* Define if console on something else */
+#define CONFIG_CONS_INDEX 1 /* Which serial channel for console */
+
+/*-----------------------------------------------------------------------
+ * Select Ethernet configuration
+ *
+ * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC).
+ *
+ * If CONFIG_ETHER_NONE is defined, then either the Ethernet routines must
+ * be defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
+ */
+#undef CONFIG_ETHER_ON_SCC /* Define if Ethernet on SCC */
+#define CONFIG_ETHER_ON_FCC /* Define if Ethernet on FCC */
+#undef CONFIG_ETHER_NONE /* Define if Ethernet on something else */
+#define CONFIG_ETHER_INDEX 3 /* Which channel for Ethernrt */
+
+#ifdef CONFIG_ETHER_ON_FCC
+
+#if CONFIG_ETHER_INDEX == 3
+
+#define CONFIG_SYS_PHY_ADDR 0
+#define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK14 | CMXFCR_TF3CS_CLK16)
+#define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
+
+#endif /* CONFIG_ETHER_INDEX == 3 */
+
+#define CONFIG_SYS_CPMFCR_RAMTYPE 0
+#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_BITBANGMII /* Bit-bang MII PHY management */
+/*
+ * GPIO pins used for bit-banged MII communications
+ */
+#define MDIO_PORT 3 /* Port D */
+#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
+ (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
+#define MDC_DECLARE MDIO_DECLARE
+
+
+#define CONFIG_SYS_MDIO_PIN 0x00040000 /* PD13 */
+#define CONFIG_SYS_MDC_PIN 0x00080000 /* PD12 */
+
+#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN)
+#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN)
+#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0)
+
+#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDIO_PIN
+
+#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDC_PIN
+
+#define MIIDELAY udelay(1)
+
+#endif /* CONFIG_ETHER_ON_FCC */
+
+#define CONFIG_8260_CLKIN 65536000 /* in Hz */
+#define CONFIG_BAUDRATE 38400
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_BOOTCOMMAND "bootm fe010000" /* autoboot command */
+#define CONFIG_BOOTARGS "root=/dev/ram rw"
+
+#define CONFIG_BZIP2 /* Include support for bzip2 compressed images */
+#undef CONFIG_WATCHDOG /* Disable platform specific watchdog */
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_LONGHELP /* #undef to save memory */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x03B00000 /* 1 ... 59 MB in SDRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* Default load address */
+
+#define CONFIG_SYS_RESET_ADDRESS 0x09900000
+
+#define CONFIG_MISC_INIT_R /* We need misc_init_r() */
+
+/*-----------------------------------------------------------------------
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#ifdef CONFIG_BZIP2
+#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
+#else
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 KB for malloc() */
+#endif /* CONFIG_BZIP2 */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max num of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 142 /* Max num of sects on one chip */
+
+/* Environment is in flash, there is little space left in Serial EEPROM */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* We use one complete sector */
+#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * If you change bits in the HRCW, you must also change the CONFIG_SYS_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
+ */
+/* 0x1686B245 */
+#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM | HRCW_BPS01 | HRCW_CIP |\
+ HRCW_L2CPC10 | HRCW_ISB110 |\
+ HRCW_BMS | HRCW_MMR11 | HRCW_APPC10 |\
+ HRCW_CS10PC01 | HRCW_MODCK_H0101 \
+ )
+/* No slaves */
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CONFIG_SYS_IMMR 0xF0F00000
+#ifdef CONFIG_SYS_REV_B
+#define CONFIG_SYS_DEFAULT_IMMR 0xFF000000
+#endif /* CONFIG_SYS_REV_B */
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+ HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID2 0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CONFIG_SYS_RMR RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration 4-25
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_BCR 0xA01C0000
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 4-31
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_SIUMCR 0x42250000/* 0x4205C000 */
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined (CONFIG_WATCHDOG)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control 9-8
+ *-----------------------------------------------------------------------
+ * Ensure DFBRG is Divide by 16
+ */
+#define CONFIG_SYS_SCCR SCCR_DFBRG01
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_RCCR 0
+
+/*-----------------------------------------------------------------------
+ * Init Memory Controller:
+ *
+ * Bank Bus Machine PortSize Device
+ * ---- --- ------- ----------------------------- ------
+ * 0 60x GPCM 8 bit (Rev.B)/16 bit (Rev.D) Flash
+ * 1 60x SDRAM 64 bit SDRAM
+ * 2 Local SDRAM 32 bit SDRAM
+ */
+#define CONFIG_SYS_USE_FIRMWARE /* If defined - do not initialise memory
+ controller, rely on initialisation
+ performed by the Interphase boot firmware.
+ */
+
+#define CONFIG_SYS_OR0_PRELIM 0xFE000882
+#ifdef CONFIG_SYS_REV_B
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BRx_PS_8 | BRx_V)
+#else /* Rev. D */
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BRx_PS_16 | BRx_V)
+#endif /* CONFIG_SYS_REV_B */
+
+#define CONFIG_SYS_MPTPR 0x7F00
+
+/* Please note that 60x SDRAM MUST start at 0 */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_60x_BR 0x00000041
+#define CONFIG_SYS_60x_OR 0xF0002CD0
+#define CONFIG_SYS_PSDMR 0x0049929A
+#define CONFIG_SYS_PSRT 0x07
+
+#define CONFIG_SYS_LSDRAM_BASE 0xF7000000
+#define CONFIG_SYS_LOC_BR 0x00001861
+#define CONFIG_SYS_LOC_OR 0xFF803280
+#define CONFIG_SYS_LSDMR 0x8285A552
+#define CONFIG_SYS_LSRT 0x07
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff