--- /dev/null
+/*
+ * (C) Copyright 2001-2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP 1 /* This is a PPC405 CPU */
+#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
+#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
+
+#undef CONFIG_HAS_ETH1
+
+#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_EEPROM
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_SUPPORT_VFAT
+
+#undef CONFIG_AUTO_UPDATE /* autoupdate via compactflash */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CONFIG_SYS_BASE_BAUD 691200
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CONFIG_LOOPW 1 /* enable loopw command */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+/* Only interrupt boot if special string is typed */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT \
+ "Autobooting in %d seconds\n", bootdelay
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#undef CONFIG_AUTOBOOT_STOP_STR /* defined via environment var */
+#define CONFIG_AUTOBOOT_STOP_STR2 "esdesd" /* esd special for esd access*/
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
+#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */
+
+#define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
+#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
+#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#if 0 /* Use NVRAM for environment variables */
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
+#define CONFIG_ENV_SIZE 0x0ff8 /* Size of Environment vars */
+#define CONFIG_ENV_ADDR \
+ (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-(CONFIG_ENV_SIZE+8)) /* Env */
+
+#else /* Use EEPROM for environment variables */
+
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+#endif
+
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
+#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
+#define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x92015480
+#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CONFIG_SYS_EBC_PB1AP 0x92015480
+#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 2 (CAN0, 1) initialization */
+#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_LED_ADDR 0xF0000380
+
+/* Memory Bank 3 (CompactFlash IDE) initialization */
+#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 4 (NVRAM/RTC) initialization */
+/*#define CONFIG_SYS_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
+#define CONFIG_SYS_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
+#define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 5 (optional Quart) initialization */
+#define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 6 (FPGA internal) initialization */
+#define CONFIG_SYS_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CONFIG_SYS_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0400000
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+/* FPGA internal regs */
+#define CONFIG_SYS_FPGA_MODE 0x00
+#define CONFIG_SYS_FPGA_STATUS 0x02
+#define CONFIG_SYS_FPGA_TS 0x04
+#define CONFIG_SYS_FPGA_TS_LOW 0x06
+#define CONFIG_SYS_FPGA_TS_CAP0 0x10
+#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12
+#define CONFIG_SYS_FPGA_TS_CAP1 0x14
+#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16
+#define CONFIG_SYS_FPGA_TS_CAP2 0x18
+#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a
+#define CONFIG_SYS_FPGA_TS_CAP3 0x1c
+#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e
+
+/* FPGA Mode Reg */
+#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001
+#define CONFIG_SYS_FPGA_MODE_DUART_RESET 0x0002
+#define CONFIG_SYS_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
+#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100
+#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000
+#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000
+
+/* FPGA Status Reg */
+#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001
+#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002
+#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004
+#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008
+#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000
+
+#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */
+
+/* FPGA program pin configuration */
+#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+#define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
+
+#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff