--- /dev/null
+/*
+ * -- Version 1.1 --
+ *
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004-2005
+ * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
+ *
+ * (C) Copyright 2005
+ * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de.
+ *
+ * History:
+ * 1.1 - add define CONFIG_ZERO_BOOTDELAY_CHECK
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */
+#define CONFIG_TQM5200 1 /* ... on a TQM5200 module */
+
+#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */
+#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */
+#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */
+#define CONFIG_BC3450_USB 1 /* + USB support */
+# define CONFIG_FAT 1 /* + FAT support */
+# define CONFIG_EXT2 1 /* + EXT2 support */
+#undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */
+#undef CONFIG_BC3450_CAN /* + CAN transceiver */
+#undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */
+#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */
+#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */
+#define CONFIG_BC3450_FP 1 /* + enable FP O/P */
+#undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */
+
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFC000000 boot low (standard configuration with room for
+ * max 64 MByte Flash ROM)
+ * 0x00100000 boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFC000000
+#endif
+
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * AT-PS/2 Multiplexer
+ */
+#ifdef CONFIG_BC3450_PS2
+# define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
+# define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
+# define CONFIG_PS2SERIAL 6 /* .. on PSC6 */
+# define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */
+# define CONFIG_BOARD_EARLY_INIT_R
+#endif /* CONFIG_BC3450_PS2 */
+
+/*
+ * PCI Mapping:
+ * 0x40000000 - 0x4fffffff - PCI Memory
+ * 0x50000000 - 0x50ffffff - PCI IO Space
+ */
+# define CONFIG_PCI 1
+# define CONFIG_PCI_PNP 1
+/* #define CONFIG_PCI_SCAN_SHOW 1 */
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
+
+#define CONFIG_PCI_MEM_BUS 0x40000000
+#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
+#define CONFIG_PCI_MEM_SIZE 0x10000000
+
+#define CONFIG_PCI_IO_BUS 0x50000000
+#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
+#define CONFIG_PCI_IO_SIZE 0x01000000
+
+/*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CONFIG_NS8382X 1
+
+/*
+ * Video console
+ */
+# define CONFIG_VIDEO
+# define CONFIG_VIDEO_SM501
+# define CONFIG_VIDEO_SM501_32BPP
+# define CONFIG_CFB_CONSOLE
+# define CONFIG_VIDEO_LOGO
+# define CONFIG_VGA_AS_SINGLE_DEVICE
+# define CONFIG_CONSOLE_EXTRA_INFO /* display Board/Device-Infos */
+# define CONFIG_VIDEO_SW_CURSOR
+# define CONFIG_SPLASH_SCREEN
+# define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+/*
+ * Partitions
+ */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+/*
+ * USB
+ */
+#ifdef CONFIG_BC3450_USB
+# define CONFIG_USB_OHCI
+# define CONFIG_USB_STORAGE
+#endif /* CONFIG_BC3450_USB */
+
+/*
+ * POST support
+ */
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_I2C)
+
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+# define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
+#endif /* CONFIG_POST */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_BSP
+
+#ifdef CONFIG_VIDEO
+ #define CONFIG_CMD_BMP
+#endif
+
+#ifdef CONFIG_BC3450_IDE
+ #define CONFIG_CMD_IDE
+#endif
+
+#if defined(CONFIG_BC3450_IDE) || defined(CONFIG_BC3450_USB)
+ #ifdef CONFIG_FAT
+ #define CONFIG_CMD_FAT
+ #endif
+
+ #ifdef CONFIG_EXT2
+ #define CONFIG_CMD_EXT2
+ #endif
+#endif
+
+#ifdef CONFIG_BC3450_USB
+ #define CONFIG_CMD_USB
+#endif
+
+#ifdef CONFIG_PCI
+ #define CONFIG_CMD_PCI
+#endif
+
+#ifdef CONFIG_POST
+ #define CONFIG_CMD_DIAG
+#endif
+
+
+#define CONFIG_TIMESTAMP /* display image timestamps */
+
+#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */
+# define CONFIG_SYS_LOWBOOT 1
+#endif
+
+/*
+ * Autobooting
+ */
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
+ "echo;"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "ipaddr=192.168.1.10\0" \
+ "serverip=192.168.1.3\0" \
+ "netmask=255.255.255.0\0" \
+ "hostname=bc3450\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "kernel_addr=fc0a0000\0" \
+ "ramdisk_addr=fc1c0000\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath)\0" \
+ "ideargs=setenv bootargs root=/dev/hda2 ro\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):$(netdev):off panic=1\0" \
+ "addcons=setenv bootargs $(bootargs) " \
+ "console=ttyS0,$(baudrate) console=tty0\0" \
+ "flash_self=run ramargs addip addcons;" \
+ "bootm $(kernel_addr) $(ramdisk_addr)\0" \
+ "flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \
+ "net_nfs=tftp 200000 $(bootfile); " \
+ "run nfsargs addip addcons; bootm\0" \
+ "ide_nfs=run nfsargs addip addcons; " \
+ "disk 200000 0:1; bootm\0" \
+ "ide_ide=run ideargs addip addcons; " \
+ "disk 200000 0:1; bootm\0" \
+ "usb_self=run usbload; run ramargs addip addcons; " \
+ "bootm 200000 400000\0" \
+ "usbload=usb reset; usb scan; usbboot 200000 0:1; " \
+ "usbboot 400000 0:2\0" \
+ "bootfile=uImage\0" \
+ "load=tftp 200000 $(u-boot)\0" \
+ "u-boot=u-boot.bin\0" \
+ "update=protect off FC000000 FC05FFFF;" \
+ "erase FC000000 FC05FFFF;" \
+ "cp.b 200000 FC000000 $(filesize);" \
+ "protect on FC000000 FC05FFFF\0" \
+ ""
+
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+
+/*
+ * PCI Bus clocking configuration
+ *
+ * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
+ * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
+ */
+#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
+# define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
+#endif
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
+
+/*
+ * I2C clock frequency
+ *
+ * Please notice, that the resulting clock frequency could differ from the
+ * configured value. This is because the I2C clock is derived from system
+ * clock over a frequency divider with only a few divider values. U-boot
+ * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
+ * approximation allways lies below the configured value, never above.
+ */
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+/*
+ * EEPROM configuration for I²C EEPROM M24C32
+ * M24C64 should work also. For other EEPROMs config should be verified.
+ *
+ * The TQM5200 module may hold an EEPROM at address 0x50.
+ */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
+
+/*
+ * RTC configuration
+ */
+#if defined (CONFIG_BC3450_DS1340) && !defined (CONFIG_BC3450_DS3231)
+# define CONFIG_RTC_M41T11 1
+# define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#else
+# define CONFIG_RTC_MPC5200 1 /* use MPC5200 internal RTC */
+# define CONFIG_BOARD_EARLY_INIT_R
+#endif
+
+/*
+ * Flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */
+
+/* use CFI flash driver if no module variant is spezified */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
+
+#if !defined(CONFIG_SYS_LOWBOOT)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
+#else /* CONFIG_SYS_LOWBOOT */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
+#endif /* CONFIG_SYS_LOWBOOT */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
+ (= chip selects) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+/* Dynamic MTD partition support */
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=TQM5200-0"
+#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+ "1408k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "16m(big-fs)," \
+ "8m(misc)"
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x10000
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/*
+ * Memory map
+ */
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
+#else
+# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
+#endif /*CONFIG_POST*/
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Ethernet configuration
+ *
+ * Define CONFIG_MPC5xxx_MII10 to force FEC at 10MBIT
+ */
+#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
+#undef CONFIG_MPC5xxx_MII10
+#define CONFIG_PHY_ADDR 0x00
+
+/*
+ * GPIO configuration on BC3450
+ *
+ * PSC1: UART1 (Service-UART) [0x xxxxxxx4]
+ * PSC2: UART2 [0x xxxxxx4x]
+ * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x]
+ * PSC3: USB2 [0x xxxxx1xx]
+ * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx]
+ * (this has to match
+ * CONFIG_USB_CONFIG which is
+ * used by usb_ohci.c to set
+ * the USB ports)
+ * Eth: 10/100Mbit Ethernet [0x xxx0xxxx]
+ * (this is reset to '5'
+ * in FEC driver: fec.c)
+ * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx]
+ * ATA/CS: ??? [0x x1xxxxxx]
+ * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx]
+ * CS1: Use Pin gpio_wkup_6 as second
+ * SDRAM chip select (mem_cs1)
+ * Timer: CAN2 / SPI
+ * I2C: CAN1 / I²C2 [0x bxxxxxxx]
+ */
+#ifdef CONFIG_BC3450_AC97
+# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502124
+#else /* PSC2=UART2 */
+# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502144
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max no of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg. Buffer Size */
+
+#define CONFIG_SYS_ALT_MEMTEST /* Enable an alternative, */
+ /* more extensive mem test */
+
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Enable loopw command.
+ */
+#define CONFIG_LOOPW
+
+/*
+ * Various low-level settings
+ */
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
+
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
+# define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
+#else
+# define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
+#endif
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
+
+/* automatic configuration of chip selects */
+#ifdef CONFIG_TQM5200
+# define CONFIG_LAST_STAGE_INIT
+#endif /* CONFIG_TQM5200 */
+
+/*
+ * SRAM - Do not map below 2 GB in address space, because this area is used
+ * for SDRAM autosizing.
+ */
+#ifdef CONFIG_TQM5200
+# define CONFIG_SYS_CS2_START 0xE5000000
+# define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */
+# define CONFIG_SYS_CS2_CFG 0x0004D930
+#endif /* CONFIG_TQM5200 */
+
+/*
+ * Grafic controller - Do not map below 2 GB in address space, because this
+ * area is used for SDRAM autosizing.
+ */
+#ifdef CONFIG_TQM5200
+# define SM501_FB_BASE 0xE0000000
+# define CONFIG_SYS_CS1_START (SM501_FB_BASE)
+# define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */
+# define CONFIG_SYS_CS1_CFG 0x8F48FF70
+# define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000
+#endif /* CONFIG_TQM5200 */
+
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */
+ /* flash and SM501 */
+
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
+
+/*
+ * USB stuff
+ */
+#define CONFIG_USB_CLOCK 0x0001BBBB
+#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */
+
+/*
+ * IDE/ATA stuff Supports IDE harddisk
+ */
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CONFIG_IDE_RESET /* reset for ide supported */
+#define CONFIG_IDE_PREINIT
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
+
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
+
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE 4
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff