--- /dev/null
+/*
+ * MPC8xx Communication Processor Module.
+ * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+ *
+ * (C) Copyright 2000-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * This file contains structures and information for the communication
+ * processor channels. Some CPM control and status is available
+ * throught the MPC8xx internal memory map. See immap.h for details.
+ * This file only contains what I need for the moment, not the total
+ * CPM capabilities. I (or someone else) will add definitions as they
+ * are needed. -- Dan
+ *
+ */
+#ifndef __CPM_8XX__
+#define __CPM_8XX__
+
+#include <asm/8xx_immap.h>
+
+/* CPM Command register.
+*/
+#define CPM_CR_RST ((ushort)0x8000)
+#define CPM_CR_OPCODE ((ushort)0x0f00)
+#define CPM_CR_CHAN ((ushort)0x00f0)
+#define CPM_CR_FLG ((ushort)0x0001)
+
+/* Some commands (there are more...later)
+*/
+#define CPM_CR_INIT_TRX ((ushort)0x0000)
+#define CPM_CR_INIT_RX ((ushort)0x0001)
+#define CPM_CR_INIT_TX ((ushort)0x0002)
+#define CPM_CR_HUNT_MODE ((ushort)0x0003)
+#define CPM_CR_STOP_TX ((ushort)0x0004)
+#define CPM_CR_RESTART_TX ((ushort)0x0006)
+#define CPM_CR_SET_GADDR ((ushort)0x0008)
+
+/* Channel numbers.
+*/
+#define CPM_CR_CH_SCC1 ((ushort)0x0000)
+#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */
+#define CPM_CR_CH_SCC2 ((ushort)0x0004)
+#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI/IDMA2/Timers */
+#define CPM_CR_CH_SCC3 ((ushort)0x0008)
+#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */
+#define CPM_CR_CH_SCC4 ((ushort)0x000c)
+#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */
+
+#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
+
+/*
+ * DPRAM defines and allocation functions
+ */
+
+/* The dual ported RAM is multi-functional. Some areas can be (and are
+ * being) used for microcode. There is an area that can only be used
+ * as data ram for buffer descriptors, which is all we use right now.
+ * Currently the first 512 and last 256 bytes are used for microcode.
+ */
+#ifdef CONFIG_SYS_ALLOC_DPRAM
+
+#define CPM_DATAONLY_BASE ((uint)0x0800)
+#define CPM_DATAONLY_SIZE ((uint)0x0700)
+#define CPM_DP_NOSPACE ((uint)0x7fffffff)
+
+#else
+
+#define CPM_SERIAL_BASE 0x0800
+#define CPM_I2C_BASE 0x0820
+#define CPM_SPI_BASE 0x0840
+#define CPM_FEC_BASE 0x0860
+#define CPM_SERIAL2_BASE 0x08E0
+#define CPM_SCC_BASE 0x0900
+#define CPM_POST_BASE 0x0980
+#define CPM_WLKBD_BASE 0x0a00
+
+#endif
+
+#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR
+#define CPM_POST_WORD_ADDR 0x07FC
+#else
+#define CPM_POST_WORD_ADDR CONFIG_SYS_CPM_POST_WORD_ADDR
+#endif
+
+#ifndef CONFIG_SYS_CPM_BOOTCOUNT_ADDR
+#define CPM_BOOTCOUNT_ADDR (CPM_POST_WORD_ADDR - 2*sizeof(ulong))
+#else
+#define CPM_BOOTCOUNT_ADDR CONFIG_SYS_CPM_BOOTCOUNT_ADDR
+#endif
+
+#define BD_IIC_START ((uint) 0x0400) /* <- please use CPM_I2C_BASE !! */
+
+/* Export the base address of the communication processor registers
+ * and dual port ram.
+ */
+extern cpm8xx_t *cpmp; /* Pointer to comm processor */
+
+/* Buffer descriptors used by many of the CPM protocols.
+*/
+typedef struct cpm_buf_desc {
+ ushort cbd_sc; /* Status and Control */
+ ushort cbd_datlen; /* Data length in buffer */
+ uint cbd_bufaddr; /* Buffer address in host memory */
+} cbd_t;
+
+#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
+#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
+#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
+#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
+#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */
+#define BD_SC_TC ((ushort)0x0400) /* Transmit CRC */
+#define BD_SC_CM ((ushort)0x0200) /* Continous mode */
+#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
+#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
+#define BD_SC_BR ((ushort)0x0020) /* Break received */
+#define BD_SC_FR ((ushort)0x0010) /* Framing error */
+#define BD_SC_PR ((ushort)0x0008) /* Parity error */
+#define BD_SC_OV ((ushort)0x0002) /* Overrun */
+#define BD_SC_CD ((ushort)0x0001) /* Carrier Detect lost */
+
+/* Parameter RAM offsets.
+*/
+#define PROFF_SCC1 ((uint)0x0000)
+#define PROFF_IIC ((uint)0x0080)
+#define PROFF_REVNUM ((uint)0x00b0)
+#define PROFF_SCC2 ((uint)0x0100)
+#define PROFF_SPI ((uint)0x0180)
+#define PROFF_SCC3 ((uint)0x0200)
+#define PROFF_SMC1 ((uint)0x0280)
+#define PROFF_SCC4 ((uint)0x0300)
+#define PROFF_SMC2 ((uint)0x0380)
+
+/* Define enough so I can at least use the serial port as a UART.
+ */
+typedef struct smc_uart {
+ ushort smc_rbase; /* Rx Buffer descriptor base address */
+ ushort smc_tbase; /* Tx Buffer descriptor base address */
+ u_char smc_rfcr; /* Rx function code */
+ u_char smc_tfcr; /* Tx function code */
+ ushort smc_mrblr; /* Max receive buffer length */
+ uint smc_rstate; /* Internal */
+ uint smc_idp; /* Internal */
+ ushort smc_rbptr; /* Internal */
+ ushort smc_ibc; /* Internal */
+ uint smc_rxtmp; /* Internal */
+ uint smc_tstate; /* Internal */
+ uint smc_tdp; /* Internal */
+ ushort smc_tbptr; /* Internal */
+ ushort smc_tbc; /* Internal */
+ uint smc_txtmp; /* Internal */
+ ushort smc_maxidl; /* Maximum idle characters */
+ ushort smc_tmpidl; /* Temporary idle counter */
+ ushort smc_brklen; /* Last received break length */
+ ushort smc_brkec; /* rcv'd break condition counter */
+ ushort smc_brkcr; /* xmt break count register */
+ ushort smc_rmask; /* Temporary bit mask */
+ u_char res1[8];
+ ushort smc_rpbase; /* Relocation pointer */
+} smc_uart_t;
+
+/* Function code bits.
+*/
+#define SMC_EB ((u_char)0x10) /* Set big endian byte order */
+
+/* SMC uart mode register.
+*/
+#define SMCMR_REN ((ushort)0x0001)
+#define SMCMR_TEN ((ushort)0x0002)
+#define SMCMR_DM ((ushort)0x000c)
+#define SMCMR_SM_GCI ((ushort)0x0000)
+#define SMCMR_SM_UART ((ushort)0x0020)
+#define SMCMR_SM_TRANS ((ushort)0x0030)
+#define SMCMR_SM_MASK ((ushort)0x0030)
+#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */
+#define SMCMR_REVD SMCMR_PM_EVEN
+#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */
+#define SMCMR_BS SMCMR_PEN
+#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */
+#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */
+#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK)
+
+/* SMC2 as Centronics parallel printer. It is half duplex, in that
+ * it can only receive or transmit. The parameter ram values for
+ * each direction are either unique or properly overlap, so we can
+ * include them in one structure.
+ */
+typedef struct smc_centronics {
+ ushort scent_rbase;
+ ushort scent_tbase;
+ u_char scent_cfcr;
+ u_char scent_smask;
+ ushort scent_mrblr;
+ uint scent_rstate;
+ uint scent_r_ptr;
+ ushort scent_rbptr;
+ ushort scent_r_cnt;
+ uint scent_rtemp;
+ uint scent_tstate;
+ uint scent_t_ptr;
+ ushort scent_tbptr;
+ ushort scent_t_cnt;
+ uint scent_ttemp;
+ ushort scent_max_sl;
+ ushort scent_sl_cnt;
+ ushort scent_character1;
+ ushort scent_character2;
+ ushort scent_character3;
+ ushort scent_character4;
+ ushort scent_character5;
+ ushort scent_character6;
+ ushort scent_character7;
+ ushort scent_character8;
+ ushort scent_rccm;
+ ushort scent_rccr;
+} smc_cent_t;
+
+/* Centronics Status Mask Register.
+*/
+#define SMC_CENT_F ((u_char)0x08)
+#define SMC_CENT_PE ((u_char)0x04)
+#define SMC_CENT_S ((u_char)0x02)
+
+/* SMC Event and Mask register.
+*/
+#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */
+#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */
+#define SMCM_TXE ((unsigned char)0x10) /* When in Transparent Mode */
+#define SMCM_BSY ((unsigned char)0x04)
+#define SMCM_TX ((unsigned char)0x02)
+#define SMCM_RX ((unsigned char)0x01)
+
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST ((uint)0x00020000)
+#define CPM_BRG_EN ((uint)0x00010000)
+#define CPM_BRG_EXTC_INT ((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK2 ((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK6 ((uint)0x00008000)
+#define CPM_BRG_ATB ((uint)0x00002000)
+#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
+#define CPM_BRG_DIV16 ((uint)0x00000001)
+
+/* SI Clock Route Register
+*/
+#define SICR_RCLK_SCC1_BRG1 ((uint)0x00000000)
+#define SICR_TCLK_SCC1_BRG1 ((uint)0x00000000)
+#define SICR_RCLK_SCC2_BRG2 ((uint)0x00000800)
+#define SICR_TCLK_SCC2_BRG2 ((uint)0x00000100)
+#define SICR_RCLK_SCC3_BRG3 ((uint)0x00100000)
+#define SICR_TCLK_SCC3_BRG3 ((uint)0x00020000)
+#define SICR_RCLK_SCC4_BRG4 ((uint)0x18000000)
+#define SICR_TCLK_SCC4_BRG4 ((uint)0x03000000)
+
+/* SCCs.
+*/
+#define SCC_GSMRH_IRP ((uint)0x00040000)
+#define SCC_GSMRH_GDE ((uint)0x00010000)
+#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000)
+#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000)
+#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000)
+#define SCC_GSMRH_REVD ((uint)0x00002000)
+#define SCC_GSMRH_TRX ((uint)0x00001000)
+#define SCC_GSMRH_TTX ((uint)0x00000800)
+#define SCC_GSMRH_CDP ((uint)0x00000400)
+#define SCC_GSMRH_CTSP ((uint)0x00000200)
+#define SCC_GSMRH_CDS ((uint)0x00000100)
+#define SCC_GSMRH_CTSS ((uint)0x00000080)
+#define SCC_GSMRH_TFL ((uint)0x00000040)
+#define SCC_GSMRH_RFW ((uint)0x00000020)
+#define SCC_GSMRH_TXSY ((uint)0x00000010)
+#define SCC_GSMRH_SYNL16 ((uint)0x0000000c)
+#define SCC_GSMRH_SYNL8 ((uint)0x00000008)
+#define SCC_GSMRH_SYNL4 ((uint)0x00000004)
+#define SCC_GSMRH_RTSM ((uint)0x00000002)
+#define SCC_GSMRH_RSYN ((uint)0x00000001)
+
+#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */
+#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000)
+#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000)
+#define SCC_GSMRL_EDGE_POS ((uint)0x20000000)
+#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000)
+#define SCC_GSMRL_TCI ((uint)0x10000000)
+#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000)
+#define SCC_GSMRL_TSNC_4 ((uint)0x08000000)
+#define SCC_GSMRL_TSNC_14 ((uint)0x04000000)
+#define SCC_GSMRL_TSNC_INF ((uint)0x00000000)
+#define SCC_GSMRL_RINV ((uint)0x02000000)
+#define SCC_GSMRL_TINV ((uint)0x01000000)
+#define SCC_GSMRL_TPL_128 ((uint)0x00c00000)
+#define SCC_GSMRL_TPL_64 ((uint)0x00a00000)
+#define SCC_GSMRL_TPL_48 ((uint)0x00800000)
+#define SCC_GSMRL_TPL_32 ((uint)0x00600000)
+#define SCC_GSMRL_TPL_16 ((uint)0x00400000)
+#define SCC_GSMRL_TPL_8 ((uint)0x00200000)
+#define SCC_GSMRL_TPL_NONE ((uint)0x00000000)
+#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000)
+#define SCC_GSMRL_TPP_01 ((uint)0x00100000)
+#define SCC_GSMRL_TPP_10 ((uint)0x00080000)
+#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000)
+#define SCC_GSMRL_TEND ((uint)0x00040000)
+#define SCC_GSMRL_TDCR_32 ((uint)0x00030000)
+#define SCC_GSMRL_TDCR_16 ((uint)0x00020000)
+#define SCC_GSMRL_TDCR_8 ((uint)0x00010000)
+#define SCC_GSMRL_TDCR_1 ((uint)0x00000000)
+#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000)
+#define SCC_GSMRL_RDCR_16 ((uint)0x00008000)
+#define SCC_GSMRL_RDCR_8 ((uint)0x00004000)
+#define SCC_GSMRL_RDCR_1 ((uint)0x00000000)
+#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000)
+#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000)
+#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000)
+#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800)
+#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000)
+#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600)
+#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400)
+#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200)
+#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100)
+#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000)
+#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */
+#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080)
+#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040)
+#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000)
+#define SCC_GSMRL_ENR ((uint)0x00000020)
+#define SCC_GSMRL_ENT ((uint)0x00000010)
+#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c)
+#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009)
+#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008)
+#define SCC_GSMRL_MODE_V14 ((uint)0x00000007)
+#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006)
+#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005)
+#define SCC_GSMRL_MODE_UART ((uint)0x00000004)
+#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003)
+#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002)
+#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000)
+
+#define SCC_TODR_TOD ((ushort)0x8000)
+
+/* SCC Event and Mask register.
+*/
+#define SCCM_TXE ((unsigned char)0x10)
+#define SCCM_BSY ((unsigned char)0x04)
+#define SCCM_TX ((unsigned char)0x02)
+#define SCCM_RX ((unsigned char)0x01)
+
+typedef struct scc_param {
+ ushort scc_rbase; /* Rx Buffer descriptor base address */
+ ushort scc_tbase; /* Tx Buffer descriptor base address */
+ u_char scc_rfcr; /* Rx function code */
+ u_char scc_tfcr; /* Tx function code */
+ ushort scc_mrblr; /* Max receive buffer length */
+ uint scc_rstate; /* Internal */
+ uint scc_idp; /* Internal */
+ ushort scc_rbptr; /* Internal */
+ ushort scc_ibc; /* Internal */
+ uint scc_rxtmp; /* Internal */
+ uint scc_tstate; /* Internal */
+ uint scc_tdp; /* Internal */
+ ushort scc_tbptr; /* Internal */
+ ushort scc_tbc; /* Internal */
+ uint scc_txtmp; /* Internal */
+ uint scc_rcrc; /* Internal */
+ uint scc_tcrc; /* Internal */
+} sccp_t;
+
+/* Function code bits.
+*/
+#define SCC_EB ((u_char)0x10) /* Set big endian byte order */
+
+/* CPM Ethernet through SCCx.
+ */
+typedef struct scc_enet {
+ sccp_t sen_genscc;
+ uint sen_cpres; /* Preset CRC */
+ uint sen_cmask; /* Constant mask for CRC */
+ uint sen_crcec; /* CRC Error counter */
+ uint sen_alec; /* alignment error counter */
+ uint sen_disfc; /* discard frame counter */
+ ushort sen_pads; /* Tx short frame pad character */
+ ushort sen_retlim; /* Retry limit threshold */
+ ushort sen_retcnt; /* Retry limit counter */
+ ushort sen_maxflr; /* maximum frame length register */
+ ushort sen_minflr; /* minimum frame length register */
+ ushort sen_maxd1; /* maximum DMA1 length */
+ ushort sen_maxd2; /* maximum DMA2 length */
+ ushort sen_maxd; /* Rx max DMA */
+ ushort sen_dmacnt; /* Rx DMA counter */
+ ushort sen_maxb; /* Max BD byte count */
+ ushort sen_gaddr1; /* Group address filter */
+ ushort sen_gaddr2;
+ ushort sen_gaddr3;
+ ushort sen_gaddr4;
+ uint sen_tbuf0data0; /* Save area 0 - current frame */
+ uint sen_tbuf0data1; /* Save area 1 - current frame */
+ uint sen_tbuf0rba; /* Internal */
+ uint sen_tbuf0crc; /* Internal */
+ ushort sen_tbuf0bcnt; /* Internal */
+ ushort sen_paddrh; /* physical address (MSB) */
+ ushort sen_paddrm;
+ ushort sen_paddrl; /* physical address (LSB) */
+ ushort sen_pper; /* persistence */
+ ushort sen_rfbdptr; /* Rx first BD pointer */
+ ushort sen_tfbdptr; /* Tx first BD pointer */
+ ushort sen_tlbdptr; /* Tx last BD pointer */
+ uint sen_tbuf1data0; /* Save area 0 - current frame */
+ uint sen_tbuf1data1; /* Save area 1 - current frame */
+ uint sen_tbuf1rba; /* Internal */
+ uint sen_tbuf1crc; /* Internal */
+ ushort sen_tbuf1bcnt; /* Internal */
+ ushort sen_txlen; /* Tx Frame length counter */
+ ushort sen_iaddr1; /* Individual address filter */
+ ushort sen_iaddr2;
+ ushort sen_iaddr3;
+ ushort sen_iaddr4;
+ ushort sen_boffcnt; /* Backoff counter */
+
+ /* NOTE: Some versions of the manual have the following items
+ * incorrectly documented. Below is the proper order.
+ */
+ ushort sen_taddrh; /* temp address (MSB) */
+ ushort sen_taddrm;
+ ushort sen_taddrl; /* temp address (LSB) */
+} scc_enet_t;
+
+/**********************************************************************
+ *
+ * Board specific configuration settings.
+ *
+ * Please note that we use the presence of a #define SCC_ENET and/or
+ * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers.
+ **********************************************************************/
+
+/*** BSEIP **********************************************************/
+
+#ifdef CONFIG_BSEIP
+/* This ENET stuff is for the MPC823 with ethernet on SCC2.
+ * This is unique to the BSE ip-Engine board.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004)
+#define PA_ENET_TXD ((ushort)0x0008)
+#define PA_ENET_TCLK ((ushort)0x0100)
+#define PA_ENET_RCLK ((ushort)0x0200)
+#define PB_ENET_TENA ((uint)0x00002000)
+#define PC_ENET_CLSN ((ushort)0x0040)
+#define PC_ENET_RENA ((ushort)0x0080)
+
+/* BSE uses port B and C bits for PHY control also.
+*/
+#define PB_BSE_POWERUP ((uint)0x00000004)
+#define PB_BSE_FDXDIS ((uint)0x00008000)
+#define PC_BSE_LOOPBACK ((ushort)0x0800)
+
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002c00)
+#endif /* CONFIG_BSEIP */
+
+/*** BSEIP **********************************************************/
+
+#ifdef CONFIG_FLAGADM
+/* Enet configuration for the FLAGADM */
+/* Enet on SCC2 */
+
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004)
+#define PA_ENET_TXD ((ushort)0x0008)
+#define PA_ENET_TCLK ((ushort)0x0100)
+#define PA_ENET_RCLK ((ushort)0x0400)
+#define PB_ENET_TENA ((uint)0x00002000)
+#define PC_ENET_CLSN ((ushort)0x0040)
+#define PC_ENET_RENA ((ushort)0x0080)
+
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00003400)
+#endif /* CONFIG_FLAGADM */
+
+/*** ELPT860 *********************************************************/
+
+#ifdef CONFIG_ELPT860
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+# define PROFF_ENET PROFF_SCC1
+# define CPM_CR_ENET CPM_CR_CH_SCC1
+# define SCC_ENET 0
+
+# define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
+# define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
+# define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
+# define PA_ENET_TCLK ((ushort)0x0200) /* PA 6 */
+
+# define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
+# define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
+# define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
+
+/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK1) to
+ * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+# define SICR_ENET_MASK ((uint)0x000000FF)
+# define SICR_ENET_CLKRT ((uint)0x00000025)
+#endif /* CONFIG_ELPT860 */
+
+/*** ESTEEM 192E **************************************************/
+#ifdef CONFIG_ESTEEM192E
+/* ESTEEM192E
+ * This ENET stuff is for the MPC850 with ethernet on SCC2. This
+ * is very similar to the RPX-Lite configuration.
+ * Note TENA , LOOPBACK , FDPLEX_DIS on Port B.
+ */
+
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+
+#define PA_ENET_RXD ((ushort)0x0004)
+#define PA_ENET_TXD ((ushort)0x0008)
+#define PA_ENET_TCLK ((ushort)0x0200)
+#define PA_ENET_RCLK ((ushort)0x0800)
+#define PB_ENET_TENA ((uint)0x00002000)
+#define PC_ENET_CLSN ((ushort)0x0040)
+#define PC_ENET_RENA ((ushort)0x0080)
+
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00003d00)
+
+#define PB_ENET_LOOPBACK ((uint)0x00004000)
+#define PB_ENET_FDPLEX_DIS ((uint)0x00008000)
+
+#endif
+
+/*** FADS860T********************************************************/
+
+#if defined(CONFIG_FADS) && defined(CONFIG_MPC86x)
+/*
+ * This ENET stuff is for the MPC86xFADS/MPC8xxADS with ethernet on SCC1.
+ */
+#ifdef CONFIG_SCC1_ENET
+
+#define SCC_ENET 0
+
+#define PROFF_ENET PROFF_SCC1
+#define CPM_CR_ENET CPM_CR_CH_SCC1
+
+#define PA_ENET_RXD ((ushort)0x0001)
+#define PA_ENET_TXD ((ushort)0x0002)
+#define PA_ENET_TCLK ((ushort)0x0100)
+#define PA_ENET_RCLK ((ushort)0x0200)
+
+#define PB_ENET_TENA ((uint)0x00001000)
+
+#define PC_ENET_CLSN ((ushort)0x0010)
+#define PC_ENET_RENA ((ushort)0x0020)
+
+#define SICR_ENET_MASK ((uint)0x000000ff)
+#define SICR_ENET_CLKRT ((uint)0x0000002c)
+
+#endif /* CONFIG_SCC1_ETHERNET */
+
+/*
+ * This ENET stuff is for the MPC860TFADS/MPC86xADS/MPC885ADS
+ * with ethernet on FEC.
+ */
+
+#ifdef CONFIG_FEC_ENET
+#define FEC_ENET /* Use FEC for Ethernet */
+#endif /* CONFIG_FEC_ENET */
+
+#endif /* CONFIG_FADS && CONFIG_MPC86x */
+
+/*** FPS850L, FPS860L ************************************************/
+
+#if defined(CONFIG_FPS850L) || defined(CONFIG_FPS860L)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
+#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
+
+#define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+
+/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
+ * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002600)
+#endif /* CONFIG_FPS850L, CONFIG_FPS860L */
+
+/*** GEN860T **********************************************************/
+#if defined(CONFIG_GEN860T)
+#undef SCC_ENET
+#define FEC_ENET
+
+#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
+#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
+#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
+#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
+#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
+#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
+#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
+#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
+#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
+#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
+#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
+#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
+#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
+#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */
+#endif /* CONFIG_GEN860T */
+
+/*** HERMES-PRO ******************************************************/
+
+/* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
+
+#ifdef CONFIG_HERMES
+
+#define FEC_ENET /* use FEC for EThernet */
+#undef SCC_ENET
+
+
+#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
+#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
+#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
+#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
+#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
+#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
+#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
+#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
+#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
+#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
+#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
+#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
+#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
+
+#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
+
+#endif /* CONFIG_HERMES */
+
+/*** ICU862 **********************************************************/
+
+#if defined(CONFIG_ICU862)
+
+#ifdef CONFIG_FEC_ENET
+#define FEC_ENET /* use FEC for EThernet */
+#endif /* CONFIG_FEC_ETHERNET */
+
+#endif /* CONFIG_ICU862 */
+
+/*** IP860 **********************************************************/
+
+#if defined(CONFIG_IP860)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PROFF_ENET PROFF_SCC1
+#define CPM_CR_ENET CPM_CR_CH_SCC1
+#define SCC_ENET 0
+#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
+#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
+#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */
+
+#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
+#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
+#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
+
+#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */
+#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */
+
+/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
+ * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x000000ff)
+#define SICR_ENET_CLKRT ((uint)0x0000002C)
+#endif /* CONFIG_IP860 */
+
+/*** IVMS8 **********************************************************/
+
+/* The IVMS8 uses the FEC on a MPC860T for Ethernet */
+
+#if defined(CONFIG_IVMS8) || defined(CONFIG_IVML24)
+
+#define FEC_ENET /* use FEC for EThernet */
+#undef SCC_ENET
+
+#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
+
+#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
+
+#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
+#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
+#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
+#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
+#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
+#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
+#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
+#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
+#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
+#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
+#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
+#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
+#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
+
+#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
+
+#endif /* CONFIG_IVMS8, CONFIG_IVML24 */
+
+/*** KUP4K, KUP4X ****************************************************/
+/* The KUP4 boards uses the FEC on a MPC8xx for Ethernet */
+
+#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
+
+#define FEC_ENET /* use FEC for EThernet */
+#undef SCC_ENET
+
+#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
+
+#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
+
+#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
+#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
+#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
+#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
+#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
+#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
+#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
+#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
+#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
+#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
+#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
+#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
+#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
+
+#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
+
+#endif /* CONFIG_KUP4K */
+
+/*** LWMON **********************************************************/
+
+#if defined(CONFIG_LWMON)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */
+#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
+
+#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
+
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to
+ * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00003E00)
+#endif /* CONFIG_LWMON */
+
+/*** KM8XX *********************************************************/
+
+/* The KM8XX Service Module uses SCC3 for Ethernet */
+
+#ifdef CONFIG_KM8XX
+#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
+#define CPM_CR_ENET CPM_CR_CH_SCC3
+#define SCC_ENET 2
+#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */
+#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */
+#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */
+#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */
+
+#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
+
+#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */
+#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */
+
+/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to
+ * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x00FF0000)
+#define SICR_ENET_CLKRT ((uint)0x00250000)
+#endif /* CONFIG_KM8XX */
+
+
+/*** MHPC ********************************************************/
+
+#if defined(CONFIG_MHPC)
+/* This ENET stuff is for the MHPC with ethernet on SCC2.
+ * Note TENA is on Port B.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
+#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
+#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */
+#endif /* CONFIG_MHPC */
+
+/*** NETVIA *******************************************************/
+
+/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */
+#if ( defined CONFIG_SVM_SC8xx )
+# ifndef CONFIG_FEC_ENET
+
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+
+ /* Bits in parallel I/O port registers that have to be set/cleared
+ * * * * to configure the pins for SCC2 use.
+ * * * */
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */
+#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
+
+#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
+
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ * * * */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00003700)
+
+# else /* Use FEC for Fast Ethernet */
+
+#undef SCC_ENET
+#define FEC_ENET
+
+#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
+#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
+#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
+#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
+#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
+#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
+#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
+#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
+#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
+#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
+#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
+#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
+#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
+
+#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
+
+# endif /* CONFIG_FEC_ENET */
+#endif /* CONFIG_SVM_SC8xx */
+
+
+#if defined(CONFIG_NETVIA)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
+#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
+
+#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
+# define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
+#elif CONFIG_NETVIA_VERSION >= 2
+# define PC_ENET_PDN ((ushort)0x0008) /* PC 12 */
+#endif
+
+#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
+
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002f00)
+
+#endif /* CONFIG_NETVIA */
+
+/*** QS850/QS823 ***************************************************/
+
+#if defined(CONFIG_QS850) || defined(CONFIG_QS823)
+#undef FEC_ENET /* Don't use FEC for EThernet */
+
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+
+#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */
+#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */
+#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */
+#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */
+#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */
+#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */
+#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */
+#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */
+#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */
+#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */
+
+/* SCC2 TXCLK from CLK2
+ * SCC2 RXCLK from CLK4
+ * SCC2 Connected to NMSI */
+#define SICR_ENET_MASK ((uint)0x00007F00)
+#define SICR_ENET_CLKRT ((uint)0x00003D00)
+
+#endif /* CONFIG_QS850/QS823 */
+
+/*** QS860T ***************************************************/
+
+#ifdef CONFIG_QS860T
+#ifdef CONFIG_FEC_ENET
+#define FEC_ENET /* use FEC for EThernet */
+#endif /* CONFIG_FEC_ETHERNET */
+
+/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
+#define PROFF_ENET PROFF_SCC1
+#define CPM_CR_ENET CPM_CR_CH_SCC1
+#define SCC_ENET 0
+
+#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */
+#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */
+#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */
+#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */
+#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */
+#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */
+
+#define SICR_ENET_MASK ((uint)0x000000ff)
+/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */
+#define SICR_ENET_CLKRT ((uint)0x0000003D)
+
+#endif /* CONFIG_QS860T */
+
+/*** RPXLITE ********************************************************/
+
+#ifdef CONFIG_RPXLITE
+/* This ENET stuff is for the MPC850 with ethernet on SCC2. Some of
+ * this may be unique to the RPX-Lite configuration.
+ * Note TENA is on Port B.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004)
+#define PA_ENET_TXD ((ushort)0x0008)
+#define PA_ENET_TCLK ((ushort)0x0200)
+#define PA_ENET_RCLK ((ushort)0x0800)
+#if defined(CONFIG_RMU)
+#define PC_ENET_TENA ((uint)0x00000002) /* PC14 */
+#else
+#define PB_ENET_TENA ((uint)0x00002000)
+#endif
+#define PC_ENET_CLSN ((ushort)0x0040)
+#define PC_ENET_RENA ((ushort)0x0080)
+
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00003d00)
+#endif /* CONFIG_RPXLITE */
+
+/*** SM850 *********************************************************/
+
+/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
+
+#ifdef CONFIG_SM850
+#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
+#define CPM_CR_ENET CPM_CR_CH_SCC3
+#define SCC_ENET 2
+#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */
+#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */
+#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
+#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
+
+#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
+#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
+
+#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */
+#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x00FF0000)
+#define SICR_ENET_CLKRT ((uint)0x00260000)
+#endif /* CONFIG_SM850 */
+
+/*** SPD823TS ******************************************************/
+
+#ifdef CONFIG_SPD823TS
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
+#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
+#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
+
+#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
+
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
+ * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002E00)
+#endif /* CONFIG_SPD823TS */
+
+/*** SXNI855T ******************************************************/
+
+#if defined(CONFIG_SXNI855T)
+
+#ifdef CONFIG_FEC_ENET
+#define FEC_ENET /* use FEC for Ethernet */
+#endif /* CONFIG_FEC_ETHERNET */
+
+#endif /* CONFIG_SXNI855T */
+
+/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
+
+#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
+ defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \
+ defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \
+ defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
+ defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \
+ defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2)
+
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#if (!defined(CONFIG_TK885D)) /* TK885D does not use SCC Ethernet */
+#define SCC_ENET 1
+#endif
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
+#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
+
+#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
+
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+#if defined(CONFIG_R360MPI)
+#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
+#endif /* CONFIG_R360MPI */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002600)
+
+# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
+#define FEC_ENET
+# endif /* CONFIG_FEC_ENET */
+
+#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
+
+/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/
+
+#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
+ defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
+ defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
+ defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
+
+# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */
+
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PROFF_ENET PROFF_SCC1
+#define CPM_CR_ENET CPM_CR_CH_SCC1
+#define SCC_ENET 0
+#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
+#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
+#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
+#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
+
+#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
+#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
+#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x000000ff)
+#define SICR_ENET_CLKRT ((uint)0x00000026)
+
+# endif /* CONFIG_SCC1_ENET */
+
+# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
+
+#define FEC_ENET
+
+#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
+#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
+#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
+#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
+#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
+#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
+#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
+#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
+#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
+#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
+#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
+#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
+#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
+
+#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
+
+# endif /* CONFIG_FEC_ENET */
+#endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */
+
+/*** V37 **********************************************************/
+
+#ifdef CONFIG_V37
+/* This ENET stuff is for the MPC823 with ethernet on SCC2. Some of
+ * this may be unique to the Marel V37 configuration.
+ * Note TENA is on Port B.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004)
+#define PA_ENET_TXD ((ushort)0x0008)
+#define PA_ENET_TCLK ((ushort)0x0400)
+#define PA_ENET_RCLK ((ushort)0x0200)
+#define PB_ENET_TENA ((uint)0x00002000)
+#define PC_ENET_CLSN ((ushort)0x0040)
+#define PC_ENET_RENA ((ushort)0x0080)
+
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002e00)
+#endif /* CONFIG_V37 */
+
+
+/*********************************************************************/
+
+/* SCC Event register as used by Ethernet.
+*/
+#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
+#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */
+#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */
+#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */
+#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
+#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */
+
+/* SCC Mode Register (PSMR) as used by Ethernet.
+*/
+#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */
+#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */
+#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */
+#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */
+#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */
+#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */
+#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */
+#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */
+#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */
+#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */
+#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */
+#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */
+#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */
+
+/* Buffer descriptor control/status used by Ethernet receive.
+*/
+#define BD_ENET_RX_EMPTY ((ushort)0x8000)
+#define BD_ENET_RX_WRAP ((ushort)0x2000)
+#define BD_ENET_RX_INTR ((ushort)0x1000)
+#define BD_ENET_RX_LAST ((ushort)0x0800)
+#define BD_ENET_RX_FIRST ((ushort)0x0400)
+#define BD_ENET_RX_MISS ((ushort)0x0100)
+#define BD_ENET_RX_LG ((ushort)0x0020)
+#define BD_ENET_RX_NO ((ushort)0x0010)
+#define BD_ENET_RX_SH ((ushort)0x0008)
+#define BD_ENET_RX_CR ((ushort)0x0004)
+#define BD_ENET_RX_OV ((ushort)0x0002)
+#define BD_ENET_RX_CL ((ushort)0x0001)
+#define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */
+
+/* Buffer descriptor control/status used by Ethernet transmit.
+*/
+#define BD_ENET_TX_READY ((ushort)0x8000)
+#define BD_ENET_TX_PAD ((ushort)0x4000)
+#define BD_ENET_TX_WRAP ((ushort)0x2000)
+#define BD_ENET_TX_INTR ((ushort)0x1000)
+#define BD_ENET_TX_LAST ((ushort)0x0800)
+#define BD_ENET_TX_TC ((ushort)0x0400)
+#define BD_ENET_TX_DEF ((ushort)0x0200)
+#define BD_ENET_TX_HB ((ushort)0x0100)
+#define BD_ENET_TX_LC ((ushort)0x0080)
+#define BD_ENET_TX_RL ((ushort)0x0040)
+#define BD_ENET_TX_RCMASK ((ushort)0x003c)
+#define BD_ENET_TX_UN ((ushort)0x0002)
+#define BD_ENET_TX_CSL ((ushort)0x0001)
+#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */
+
+/* SCC as UART
+*/
+typedef struct scc_uart {
+ sccp_t scc_genscc;
+ uint scc_res1; /* Reserved */
+ uint scc_res2; /* Reserved */
+ ushort scc_maxidl; /* Maximum idle chars */
+ ushort scc_idlc; /* temp idle counter */
+ ushort scc_brkcr; /* Break count register */
+ ushort scc_parec; /* receive parity error counter */
+ ushort scc_frmec; /* receive framing error counter */
+ ushort scc_nosec; /* receive noise counter */
+ ushort scc_brkec; /* receive break condition counter */
+ ushort scc_brkln; /* last received break length */
+ ushort scc_uaddr1; /* UART address character 1 */
+ ushort scc_uaddr2; /* UART address character 2 */
+ ushort scc_rtemp; /* Temp storage */
+ ushort scc_toseq; /* Transmit out of sequence char */
+ ushort scc_char1; /* control character 1 */
+ ushort scc_char2; /* control character 2 */
+ ushort scc_char3; /* control character 3 */
+ ushort scc_char4; /* control character 4 */
+ ushort scc_char5; /* control character 5 */
+ ushort scc_char6; /* control character 6 */
+ ushort scc_char7; /* control character 7 */
+ ushort scc_char8; /* control character 8 */
+ ushort scc_rccm; /* receive control character mask */
+ ushort scc_rccr; /* receive control character register */
+ ushort scc_rlbc; /* receive last break character */
+} scc_uart_t;
+
+/* SCC Event and Mask registers when it is used as a UART.
+*/
+#define UART_SCCM_GLR ((ushort)0x1000)
+#define UART_SCCM_GLT ((ushort)0x0800)
+#define UART_SCCM_AB ((ushort)0x0200)
+#define UART_SCCM_IDL ((ushort)0x0100)
+#define UART_SCCM_GRA ((ushort)0x0080)
+#define UART_SCCM_BRKE ((ushort)0x0040)
+#define UART_SCCM_BRKS ((ushort)0x0020)
+#define UART_SCCM_CCR ((ushort)0x0008)
+#define UART_SCCM_BSY ((ushort)0x0004)
+#define UART_SCCM_TX ((ushort)0x0002)
+#define UART_SCCM_RX ((ushort)0x0001)
+
+/* The SCC PSMR when used as a UART.
+*/
+#define SCU_PSMR_FLC ((ushort)0x8000)
+#define SCU_PSMR_SL ((ushort)0x4000)
+#define SCU_PSMR_CL ((ushort)0x3000)
+#define SCU_PSMR_UM ((ushort)0x0c00)
+#define SCU_PSMR_FRZ ((ushort)0x0200)
+#define SCU_PSMR_RZS ((ushort)0x0100)
+#define SCU_PSMR_SYN ((ushort)0x0080)
+#define SCU_PSMR_DRT ((ushort)0x0040)
+#define SCU_PSMR_PEN ((ushort)0x0010)
+#define SCU_PSMR_RPM ((ushort)0x000c)
+#define SCU_PSMR_REVP ((ushort)0x0008)
+#define SCU_PSMR_TPM ((ushort)0x0003)
+#define SCU_PSMR_TEVP ((ushort)0x0003)
+
+/* CPM Transparent mode SCC.
+ */
+typedef struct scc_trans {
+ sccp_t st_genscc;
+ uint st_cpres; /* Preset CRC */
+ uint st_cmask; /* Constant mask for CRC */
+} scc_trans_t;
+
+#define BD_SCC_TX_LAST ((ushort)0x0800)
+
+/* IIC parameter RAM.
+*/
+typedef struct iic {
+ ushort iic_rbase; /* Rx Buffer descriptor base address */
+ ushort iic_tbase; /* Tx Buffer descriptor base address */
+ u_char iic_rfcr; /* Rx function code */
+ u_char iic_tfcr; /* Tx function code */
+ ushort iic_mrblr; /* Max receive buffer length */
+ uint iic_rstate; /* Internal */
+ uint iic_rdp; /* Internal */
+ ushort iic_rbptr; /* Internal */
+ ushort iic_rbc; /* Internal */
+ uint iic_rxtmp; /* Internal */
+ uint iic_tstate; /* Internal */
+ uint iic_tdp; /* Internal */
+ ushort iic_tbptr; /* Internal */
+ ushort iic_tbc; /* Internal */
+ uint iic_txtmp; /* Internal */
+ uint iic_res; /* reserved */
+ ushort iic_rpbase; /* Relocation pointer */
+ ushort iic_res2; /* reserved */
+} iic_t;
+
+/* SPI parameter RAM.
+*/
+typedef struct spi {
+ ushort spi_rbase; /* Rx Buffer descriptor base address */
+ ushort spi_tbase; /* Tx Buffer descriptor base address */
+ u_char spi_rfcr; /* Rx function code */
+ u_char spi_tfcr; /* Tx function code */
+ ushort spi_mrblr; /* Max receive buffer length */
+ uint spi_rstate; /* Internal */
+ uint spi_rdp; /* Internal */
+ ushort spi_rbptr; /* Internal */
+ ushort spi_rbc; /* Internal */
+ uint spi_rxtmp; /* Internal */
+ uint spi_tstate; /* Internal */
+ uint spi_tdp; /* Internal */
+ ushort spi_tbptr; /* Internal */
+ ushort spi_tbc; /* Internal */
+ uint spi_txtmp; /* Internal */
+ uint spi_res;
+ ushort spi_rpbase; /* Relocation pointer */
+ ushort spi_res2;
+} spi_t;
+
+/* SPI Mode register.
+*/
+#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */
+#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */
+#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */
+#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */
+#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */
+#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */
+#define SPMODE_EN ((ushort)0x0100) /* Enable */
+#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */
+#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */
+
+#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4)
+#define SPMODE_PM(x) ((x) &0xF)
+
+/* HDLC parameter RAM.
+*/
+
+typedef struct hdlc_pram_s {
+ /*
+ * SCC parameter RAM
+ */
+ ushort rbase; /* Rx Buffer descriptor base address */
+ ushort tbase; /* Tx Buffer descriptor base address */
+ uchar rfcr; /* Rx function code */
+ uchar tfcr; /* Tx function code */
+ ushort mrblr; /* Rx buffer length */
+ ulong rstate; /* Rx internal state */
+ ulong rptr; /* Rx internal data pointer */
+ ushort rbptr; /* rb BD Pointer */
+ ushort rcount; /* Rx internal byte count */
+ ulong rtemp; /* Rx temp */
+ ulong tstate; /* Tx internal state */
+ ulong tptr; /* Tx internal data pointer */
+ ushort tbptr; /* Tx BD pointer */
+ ushort tcount; /* Tx byte count */
+ ulong ttemp; /* Tx temp */
+ ulong rcrc; /* temp receive CRC */
+ ulong tcrc; /* temp transmit CRC */
+ /*
+ * HDLC specific parameter RAM
+ */
+ uchar res[4]; /* reserved */
+ ulong c_mask; /* CRC constant */
+ ulong c_pres; /* CRC preset */
+ ushort disfc; /* discarded frame counter */
+ ushort crcec; /* CRC error counter */
+ ushort abtsc; /* abort sequence counter */
+ ushort nmarc; /* nonmatching address rx cnt */
+ ushort retrc; /* frame retransmission cnt */
+ ushort mflr; /* maximum frame length reg */
+ ushort max_cnt; /* maximum length counter */
+ ushort rfthr; /* received frames threshold */
+ ushort rfcnt; /* received frames count */
+ ushort hmask; /* user defined frm addr mask */
+ ushort haddr1; /* user defined frm address 1 */
+ ushort haddr2; /* user defined frm address 2 */
+ ushort haddr3; /* user defined frm address 3 */
+ ushort haddr4; /* user defined frm address 4 */
+ ushort tmp; /* temp */
+ ushort tmp_mb; /* temp */
+} hdlc_pram_t;
+
+/* CPM interrupts. There are nearly 32 interrupts generated by CPM
+ * channels or devices. All of these are presented to the PPC core
+ * as a single interrupt. The CPM interrupt handler dispatches its
+ * own handlers, in a similar fashion to the PPC core handler. We
+ * use the table as defined in the manuals (i.e. no special high
+ * priority and SCC1 == SCCa, etc...).
+ */
+#define CPMVEC_NR 32
+#define CPMVEC_OFFSET 0x00010000
+#define CPMVEC_PIO_PC15 ((ushort)0x1f | CPMVEC_OFFSET)
+#define CPMVEC_SCC1 ((ushort)0x1e | CPMVEC_OFFSET)
+#define CPMVEC_SCC2 ((ushort)0x1d | CPMVEC_OFFSET)
+#define CPMVEC_SCC3 ((ushort)0x1c | CPMVEC_OFFSET)
+#define CPMVEC_SCC4 ((ushort)0x1b | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC14 ((ushort)0x1a | CPMVEC_OFFSET)
+#define CPMVEC_TIMER1 ((ushort)0x19 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC13 ((ushort)0x18 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC12 ((ushort)0x17 | CPMVEC_OFFSET)
+#define CPMVEC_SDMA_CB_ERR ((ushort)0x16 | CPMVEC_OFFSET)
+#define CPMVEC_IDMA1 ((ushort)0x15 | CPMVEC_OFFSET)
+#define CPMVEC_IDMA2 ((ushort)0x14 | CPMVEC_OFFSET)
+#define CPMVEC_TIMER2 ((ushort)0x12 | CPMVEC_OFFSET)
+#define CPMVEC_RISCTIMER ((ushort)0x11 | CPMVEC_OFFSET)
+#define CPMVEC_I2C ((ushort)0x10 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC11 ((ushort)0x0f | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC10 ((ushort)0x0e | CPMVEC_OFFSET)
+#define CPMVEC_TIMER3 ((ushort)0x0c | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC9 ((ushort)0x0b | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC8 ((ushort)0x0a | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC7 ((ushort)0x09 | CPMVEC_OFFSET)
+#define CPMVEC_TIMER4 ((ushort)0x07 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC6 ((ushort)0x06 | CPMVEC_OFFSET)
+#define CPMVEC_SPI ((ushort)0x05 | CPMVEC_OFFSET)
+#define CPMVEC_SMC1 ((ushort)0x04 | CPMVEC_OFFSET)
+#define CPMVEC_SMC2 ((ushort)0x03 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC5 ((ushort)0x02 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC4 ((ushort)0x01 | CPMVEC_OFFSET)
+#define CPMVEC_ERROR ((ushort)0x00 | CPMVEC_OFFSET)
+
+extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id);
+
+/* CPM interrupt configuration vector.
+*/
+#define CICR_SCD_SCC4 ((uint)0x00c00000) /* SCC4 @ SCCd */
+#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */
+#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */
+#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */
+#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */
+#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */
+#define CICR_IEN ((uint)0x00000080) /* Int. enable */
+#define CICR_SPS ((uint)0x00000001) /* SCC Spread */
+#endif /* __CPM_8XX__ */
Code Review / kvmfornfv.git / blobdiff