--- /dev/null
+/*
+ * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <usb.h>
+#include <errno.h>
+#include <linux/compiler.h>
+#include <usb/ehci-fsl.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/clock.h>
+#include <asm/imx-common/iomux-v3.h>
+
+#include "ehci.h"
+
+#define USB_OTGREGS_OFFSET 0x000
+#define USB_H1REGS_OFFSET 0x200
+#define USB_H2REGS_OFFSET 0x400
+#define USB_H3REGS_OFFSET 0x600
+#define USB_OTHERREGS_OFFSET 0x800
+
+#define USB_H1_CTRL_OFFSET 0x04
+
+#define USBPHY_CTRL 0x00000030
+#define USBPHY_CTRL_SET 0x00000034
+#define USBPHY_CTRL_CLR 0x00000038
+#define USBPHY_CTRL_TOG 0x0000003c
+
+#define USBPHY_PWD 0x00000000
+#define USBPHY_CTRL_SFTRST 0x80000000
+#define USBPHY_CTRL_CLKGATE 0x40000000
+#define USBPHY_CTRL_ENUTMILEVEL3 0x00008000
+#define USBPHY_CTRL_ENUTMILEVEL2 0x00004000
+#define USBPHY_CTRL_OTG_ID 0x08000000
+
+#define ANADIG_USB2_CHRG_DETECT_EN_B 0x00100000
+#define ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B 0x00080000
+
+#define ANADIG_USB2_PLL_480_CTRL_BYPASS 0x00010000
+#define ANADIG_USB2_PLL_480_CTRL_ENABLE 0x00002000
+#define ANADIG_USB2_PLL_480_CTRL_POWER 0x00001000
+#define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS 0x00000040
+
+
+#define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */
+#define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */
+
+/* USBCMD */
+#define UCMD_RUN_STOP (1 << 0) /* controller run/stop */
+#define UCMD_RESET (1 << 1) /* controller reset */
+
+static const unsigned phy_bases[] = {
+ USB_PHY0_BASE_ADDR,
+ USB_PHY1_BASE_ADDR,
+};
+
+static void usb_internal_phy_clock_gate(int index, int on)
+{
+ void __iomem *phy_reg;
+
+ if (index >= ARRAY_SIZE(phy_bases))
+ return;
+
+ phy_reg = (void __iomem *)phy_bases[index];
+ phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
+ __raw_writel(USBPHY_CTRL_CLKGATE, phy_reg);
+}
+
+static void usb_power_config(int index)
+{
+ struct anatop_regs __iomem *anatop =
+ (struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
+ void __iomem *chrg_detect;
+ void __iomem *pll_480_ctrl_clr;
+ void __iomem *pll_480_ctrl_set;
+
+ switch (index) {
+ case 0:
+ chrg_detect = &anatop->usb1_chrg_detect;
+ pll_480_ctrl_clr = &anatop->usb1_pll_480_ctrl_clr;
+ pll_480_ctrl_set = &anatop->usb1_pll_480_ctrl_set;
+ break;
+ case 1:
+ chrg_detect = &anatop->usb2_chrg_detect;
+ pll_480_ctrl_clr = &anatop->usb2_pll_480_ctrl_clr;
+ pll_480_ctrl_set = &anatop->usb2_pll_480_ctrl_set;
+ break;
+ default:
+ return;
+ }
+ /*
+ * Some phy and power's special controls
+ * 1. The external charger detector needs to be disabled
+ * or the signal at DP will be poor
+ * 2. The PLL's power and output to usb
+ * is totally controlled by IC, so the Software only needs
+ * to enable them at initializtion.
+ */
+ __raw_writel(ANADIG_USB2_CHRG_DETECT_EN_B |
+ ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
+ chrg_detect);
+
+ __raw_writel(ANADIG_USB2_PLL_480_CTRL_BYPASS,
+ pll_480_ctrl_clr);
+
+ __raw_writel(ANADIG_USB2_PLL_480_CTRL_ENABLE |
+ ANADIG_USB2_PLL_480_CTRL_POWER |
+ ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS,
+ pll_480_ctrl_set);
+}
+
+/* Return 0 : host node, <>0 : device mode */
+static int usb_phy_enable(int index, struct usb_ehci *ehci)
+{
+ void __iomem *phy_reg;
+ void __iomem *phy_ctrl;
+ void __iomem *usb_cmd;
+ u32 val;
+
+ if (index >= ARRAY_SIZE(phy_bases))
+ return 0;
+
+ phy_reg = (void __iomem *)phy_bases[index];
+ phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
+ usb_cmd = (void __iomem *)&ehci->usbcmd;
+
+ /* Stop then Reset */
+ val = __raw_readl(usb_cmd);
+ val &= ~UCMD_RUN_STOP;
+ __raw_writel(val, usb_cmd);
+ while (__raw_readl(usb_cmd) & UCMD_RUN_STOP)
+ ;
+
+ val = __raw_readl(usb_cmd);
+ val |= UCMD_RESET;
+ __raw_writel(val, usb_cmd);
+ while (__raw_readl(usb_cmd) & UCMD_RESET)
+ ;
+
+ /* Reset USBPHY module */
+ val = __raw_readl(phy_ctrl);
+ val |= USBPHY_CTRL_SFTRST;
+ __raw_writel(val, phy_ctrl);
+ udelay(10);
+
+ /* Remove CLKGATE and SFTRST */
+ val = __raw_readl(phy_ctrl);
+ val &= ~(USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST);
+ __raw_writel(val, phy_ctrl);
+ udelay(10);
+
+ /* Power up the PHY */
+ __raw_writel(0, phy_reg + USBPHY_PWD);
+ /* enable FS/LS device */
+ val = __raw_readl(phy_ctrl);
+ val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3);
+ __raw_writel(val, phy_ctrl);
+
+ return val & USBPHY_CTRL_OTG_ID;
+}
+
+/* Base address for this IP block is 0x02184800 */
+struct usbnc_regs {
+ u32 ctrl[4]; /* otg/host1-3 */
+ u32 uh2_hsic_ctrl;
+ u32 uh3_hsic_ctrl;
+ u32 otg_phy_ctrl_0;
+ u32 uh1_phy_ctrl_0;
+};
+
+static void usb_oc_config(int index)
+{
+ struct usbnc_regs *usbnc = (struct usbnc_regs *)(USBOH3_USB_BASE_ADDR +
+ USB_OTHERREGS_OFFSET);
+ void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
+ u32 val;
+
+ val = __raw_readl(ctrl);
+#if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
+ /* mx6qarm2 seems to required a different setting*/
+ val &= ~UCTRL_OVER_CUR_POL;
+#else
+ val |= UCTRL_OVER_CUR_POL;
+#endif
+ __raw_writel(val, ctrl);
+
+ val = __raw_readl(ctrl);
+ val |= UCTRL_OVER_CUR_DIS;
+ __raw_writel(val, ctrl);
+}
+
+int __weak board_ehci_hcd_init(int port)
+{
+ return 0;
+}
+
+int __weak board_ehci_power(int port, int on)
+{
+ return 0;
+}
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ enum usb_init_type type;
+ struct usb_ehci *ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR +
+ (0x200 * index));
+
+ if (index > 3)
+ return -EINVAL;
+ enable_usboh3_clk(1);
+ mdelay(1);
+
+ /* Do board specific initialization */
+ board_ehci_hcd_init(index);
+
+ usb_power_config(index);
+ usb_oc_config(index);
+ usb_internal_phy_clock_gate(index, 1);
+ type = usb_phy_enable(index, ehci) ? USB_INIT_DEVICE : USB_INIT_HOST;
+
+ *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+ *hcor = (struct ehci_hcor *)((uint32_t)*hccr +
+ HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+
+ if ((type == init) || (type == USB_INIT_DEVICE))
+ board_ehci_power(index, (type == USB_INIT_DEVICE) ? 0 : 1);
+ if (type != init)
+ return -ENODEV;
+ if (type == USB_INIT_DEVICE)
+ return 0;
+ setbits_le32(&ehci->usbmode, CM_HOST);
+ __raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
+ setbits_le32(&ehci->portsc, USB_EN);
+
+ mdelay(10);
+
+ return 0;
+}
+
+int ehci_hcd_stop(int index)
+{
+ return 0;
+}
Code Review / kvmfornfv.git / blobdiff