Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / drivers / power / twl4030.c

diff --git a/qemu/roms/u-boot/drivers/power/twl4030.c b/qemu/roms/u-boot/drivers/power/twl4030.c
new file mode 100644 (file)
index 0000000..3e50310
--- /dev/null
+++ b/qemu/roms/u-boot/drivers/power/twl4030.c
@@ -0,0 +1,101 @@
+/*
+ * Copyright (c) 2009 Wind River Systems, Inc.
+ * Tom Rix <Tom.Rix at windriver.com>
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ *
+ * twl4030_power_reset_init is derived from code on omapzoom,
+ * git://git.omapzoom.com/repo/u-boot.git
+ *
+ * Copyright (C) 2007-2009 Texas Instruments, Inc.
+ *
+ * twl4030_power_init is from cpu/omap3/common.c, power_init_r
+ *
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ *     Sunil Kumar <sunilsaini05 at gmail.com>
+ *     Shashi Ranjan <shashiranjanmca05 at gmail.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ *     Richard Woodruff <r-woodruff2 at ti.com>
+ *     Syed Mohammed Khasim <khasim at ti.com>
+ */
+
+#include <twl4030.h>
+
+/*
+ * Power Reset
+ */
+void twl4030_power_reset_init(void)
+{
+       u8 val = 0;
+       if (twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER,
+                               TWL4030_PM_MASTER_P1_SW_EVENTS, &val)) {
+               printf("Error:TWL4030: failed to read the power register\n");
+               printf("Could not initialize hardware reset\n");
+       } else {
+               val |= TWL4030_PM_MASTER_SW_EVENTS_STOPON_PWRON;
+               if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+                                        TWL4030_PM_MASTER_P1_SW_EVENTS, val)) {
+                       printf("Error:TWL4030: failed to write the power register\n");
+                       printf("Could not initialize hardware reset\n");
+               }
+       }
+}
+
+/*
+ * Set Device Group and Voltage
+ */
+void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val,
+                               u8 dev_grp, u8 dev_grp_sel)
+{
+       int ret;
+
+       /* Select the Voltage */
+       ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_reg,
+                                  vsel_val);
+       if (ret != 0) {
+               printf("Could not write vsel to reg %02x (%d)\n",
+                       vsel_reg, ret);
+               return;
+       }
+
+       /* Select the Device Group (enable the supply if dev_grp_sel != 0) */
+       ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp,
+                                  dev_grp_sel);
+       if (ret != 0)
+               printf("Could not write grp_sel to reg %02x (%d)\n",
+                       dev_grp, ret);
+}
+
+void twl4030_power_init(void)
+{
+       /* set VAUX3 to 2.8V */
+       twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX3_DEDICATED,
+                               TWL4030_PM_RECEIVER_VAUX3_VSEL_28,
+                               TWL4030_PM_RECEIVER_VAUX3_DEV_GRP,
+                               TWL4030_PM_RECEIVER_DEV_GRP_P1);
+
+       /* set VPLL2 to 1.8V */
+       twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VPLL2_DEDICATED,
+                               TWL4030_PM_RECEIVER_VPLL2_VSEL_18,
+                               TWL4030_PM_RECEIVER_VPLL2_DEV_GRP,
+                               TWL4030_PM_RECEIVER_DEV_GRP_ALL);
+
+       /* set VDAC to 1.8V */
+       twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VDAC_DEDICATED,
+                               TWL4030_PM_RECEIVER_VDAC_VSEL_18,
+                               TWL4030_PM_RECEIVER_VDAC_DEV_GRP,
+                               TWL4030_PM_RECEIVER_DEV_GRP_P1);
+}
+
+void twl4030_power_mmc_init(void)
+{
+       /* Set VMMC1 to 3.15 Volts */
+       twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VMMC1_DEDICATED,
+                               TWL4030_PM_RECEIVER_VMMC1_VSEL_32,
+                               TWL4030_PM_RECEIVER_VMMC1_DEV_GRP,
+                               TWL4030_PM_RECEIVER_DEV_GRP_P1);
+}