Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / drivers / power / palmas.c

diff --git a/qemu/roms/u-boot/drivers/power/palmas.c b/qemu/roms/u-boot/drivers/power/palmas.c
new file mode 100644 (file)
index 0000000..cfbc9dc
--- /dev/null
+++ b/qemu/roms/u-boot/drivers/power/palmas.c
@@ -0,0 +1,160 @@
+/*
+ * (C) Copyright 2012-2013
+ * Texas Instruments, <www.ti.com>
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+#include <config.h>
+#include <palmas.h>
+
+void palmas_init_settings(void)
+{
+#ifdef CONFIG_PALMAS_SMPS7_FPWM
+       int err;
+       /*
+        * Set SMPS7 (1.8 V I/O supply on platforms with TWL6035/37) to
+        * forced PWM mode. This reduces noise (but affects efficiency).
+        */
+       u8 val = SMPS_MODE_SLP_FPWM | SMPS_MODE_ACT_FPWM;
+       err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS7_CTRL, val);
+       if (err)
+               printf("palmas: could not force PWM for SMPS7: err = %d\n",
+                      err);
+#endif
+}
+
+int palmas_mmc1_poweron_ldo(void)
+{
+       u8 val = 0;
+
+#if defined(CONFIG_DRA7XX)
+       /*
+        * Currently valid for the dra7xx_evm board:
+        * Set TPS659038 LDO1 to 3.0 V
+        */
+       val = LDO_VOLT_3V0;
+       if (palmas_i2c_write_u8(TPS65903X_CHIP_P1, LDO1_VOLTAGE, val)) {
+               printf("tps65903x: could not set LDO1 voltage.\n");
+               return 1;
+       }
+       /* TURN ON LDO1 */
+       val = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
+       if (palmas_i2c_write_u8(TPS65903X_CHIP_P1, LDO1_CTRL, val)) {
+               printf("tps65903x: could not turn on LDO1.\n");
+               return 1;
+       }
+       return 0;
+#else
+       /*
+        * We assume that this is a OMAP543X + TWL603X board:
+        * Set TWL6035/37 LDO9 to 3.0 V
+        */
+       val = LDO_VOLT_3V0;
+       return twl603x_mmc1_set_ldo9(val);
+#endif
+}
+
+/*
+ * On some OMAP5 + TWL603X hardware the SD card socket and LDO9_IN are
+ * powered by an external 3.3 V regulator, while the output of LDO9
+ * supplies VDDS_SDCARD for the OMAP5 interface only. This implies that
+ * LDO9 could be set to 'bypass' mode when required (e.g. for 3.3 V cards).
+ */
+int twl603x_mmc1_set_ldo9(u8 vsel)
+{
+       u8 cval = 0, vval = 0;  /* Off by default */
+       int err;
+
+       if (vsel) {
+               /* Turn on */
+               if (vsel > LDO_VOLT_3V3) {
+                       /* Put LDO9 in bypass */
+                       cval = LDO9_BYP_EN | RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
+                       vval = LDO_VOLT_3V3;
+               } else {
+                       cval = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
+                       vval = vsel & 0x3f;
+               }
+       }
+       err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_VOLTAGE, vval);
+       if (err) {
+               printf("twl603x: could not set LDO9 %s: err = %d\n",
+                      vsel > LDO_VOLT_3V3 ? "bypass" : "voltage", err);
+               return err;
+       }
+       err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_CTRL, cval);
+       if (err)
+               printf("twl603x: could not turn %s LDO9: err = %d\n",
+                      cval ? "on" : "off", err);
+       return err;
+}
+
+#ifdef CONFIG_PALMAS_AUDPWR
+/*
+ * Turn audio codec power and 32 kHz clock on/off. Use for
+ * testing OMAP543X + TWL603X + TWL604X boards only.
+ */
+int twl603x_audio_power(u8 on)
+{
+       u8 cval = 0, vval = 0, c32k = 0;
+       int err;
+
+       if (on) {
+               vval = SMPS_VOLT_2V1;
+               cval = SMPS_MODE_SLP_AUTO | SMPS_MODE_ACT_AUTO;
+               c32k = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
+       }
+       /* Set SMPS9 to 2.1 V (for TWL604x), or to 0 (off) */
+       err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_VOLTAGE, vval);
+       if (err) {
+               printf("twl603x: could not set SMPS9 voltage: err = %d\n",
+                      err);
+               return err;
+       }
+       /* Turn on or off SMPS9 */
+       err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_CTRL, cval);
+       if (err) {
+               printf("twl603x: could not turn SMPS9 %s: err = %d\n",
+                      cval ? "on" : "off", err);
+               return err;
+       }
+       /* Output 32 kHz clock on or off */
+       err = palmas_i2c_write_u8(TWL603X_CHIP_P1, CLK32KGAUDIO_CTRL, c32k);
+       if (err)
+               printf("twl603x: could not turn CLK32KGAUDIO %s: err = %d\n",
+                      c32k ? "on" : "off", err);
+       return err;
+}
+#endif
+
+#ifdef CONFIG_PALMAS_USB_SS_PWR
+/**
+ * @brief palmas_enable_ss_ldo - Configure EVM board specific configurations
+ * for the USB Super speed SMPS10 regulator.
+ *
+ * @return 0
+ */
+int palmas_enable_ss_ldo(void)
+{
+       /* Enable smps10 regulator  */
+       return palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS10_CTRL,
+                               SMPS10_MODE_ACTIVE_D);
+}
+#endif
+
+/*
+ * Enable/disable back-up battery (or super cap) charging on TWL6035/37.
+ * Please use defined BB_xxx values.
+ */
+int twl603x_enable_bb_charge(u8 bb_fields)
+{
+       u8 val = bb_fields & 0x0f;
+       int err;
+
+       val |= (VRTC_EN_SLP | VRTC_EN_OFF | VRTC_PWEN);
+       err = palmas_i2c_write_u8(TWL603X_CHIP_P1, BB_VRTC_CTRL, val);
+       if (err)
+               printf("twl603x: could not set BB_VRTC_CTRL to 0x%02x: err = %d\n",
+                      val, err);
+       return err;
+}