--- /dev/null
+/*
+ * (C) Copyright 2003-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc5xxx.h>
+#include <net.h>
+#include <asm/processor.h>
+
+
+#ifndef CONFIG_SYS_RAMBOOT
+static void sdram_start(int hi_addr)
+{
+ long hi_addr_bit = hi_addr ? 0x01000000 : 0;
+
+ /* unlock mode register */
+ *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
+ __asm__ volatile ("sync");
+
+ /* precharge all banks */
+ *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+ __asm__ volatile ("sync");
+
+#if SDRAM_DDR
+ /* set mode register: extended mode */
+ *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
+ __asm__ volatile ("sync");
+
+ /* set mode register: reset DLL */
+ *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
+ __asm__ volatile ("sync");
+#endif /* SDRAM_DDR */
+
+ /* precharge all banks */
+ *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+ __asm__ volatile ("sync");
+
+ /* auto refresh */
+ *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
+ __asm__ volatile ("sync");
+
+ /* set mode register */
+ *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+ __asm__ volatile ("sync");
+
+ /* normal operation */
+ *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+ __asm__ volatile ("sync");
+}
+#endif /* !CONFIG_SYS_RAMBOOT */
+
+
+phys_size_t initdram(int board_type)
+{
+ ulong dramsize = 0;
+ ulong dramsize2 = 0;
+ uint svr, pvr;
+
+#ifndef CONFIG_SYS_RAMBOOT
+ ulong test1, test2;
+
+ /* setup SDRAM chip selects */
+ *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
+ *(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
+ __asm__ volatile ("sync");
+
+ /* setup config registers */
+ *(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+ *(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+ __asm__ volatile ("sync");
+
+#if SDRAM_DDR
+ /* set tap delay */
+ *(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
+ __asm__ volatile ("sync");
+#endif /* SDRAM_DDR */
+
+ /* find RAM size using SDRAM CS0 only */
+ sdram_start(0);
+ test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
+ sdram_start(1);
+ test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
+ if (test1 > test2) {
+ sdram_start(0);
+ dramsize = test1;
+ } else
+ dramsize = test2;
+
+ /* memory smaller than 1MB is impossible */
+ if (dramsize < (1 << 20))
+ dramsize = 0;
+
+ /* set SDRAM CS0 size according to the amount of RAM found */
+ if (dramsize > 0)
+ *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
+ else
+ *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+
+ /* let SDRAM CS1 start right after CS0 */
+ *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
+
+ /* find RAM size using SDRAM CS1 only */
+ if (!dramsize)
+ sdram_start(0);
+ test2 = test1 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
+ if (!dramsize) {
+ sdram_start(1);
+ test2 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
+ }
+ if (test1 > test2) {
+ sdram_start(0);
+ dramsize2 = test1;
+ } else
+ dramsize2 = test2;
+
+ /* memory smaller than 1MB is impossible */
+ if (dramsize2 < (1 << 20))
+ dramsize2 = 0;
+
+ /* set SDRAM CS1 size according to the amount of RAM found */
+ if (dramsize2 > 0)
+ *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize
+ | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
+ else
+ *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
+
+#else /* CONFIG_SYS_RAMBOOT */
+
+ /* retrieve size of memory connected to SDRAM CS0 */
+ dramsize = *(vu_long *) MPC5XXX_SDRAM_CS0CFG & 0xFF;
+ if (dramsize >= 0x13)
+ dramsize = (1 << (dramsize - 0x13)) << 20;
+ else
+ dramsize = 0;
+
+ /* retrieve size of memory connected to SDRAM CS1 */
+ dramsize2 = *(vu_long *) MPC5XXX_SDRAM_CS1CFG & 0xFF;
+ if (dramsize2 >= 0x13)
+ dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
+ else
+ dramsize2 = 0;
+
+#endif /* CONFIG_SYS_RAMBOOT */
+
+ /*
+ * On MPC5200B we need to set the special configuration delay in the
+ * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
+ * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
+ *
+ * "The SDelay should be written to a value of 0x00000004. It is
+ * required to account for changes caused by normal wafer processing
+ * parameters."
+ */
+ svr = get_svr();
+ pvr = get_pvr();
+ if ((SVR_MJREV(svr) >= 2) &&
+ (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
+
+ *(vu_long *) MPC5XXX_SDRAM_SDELAY = 0x04;
+ __asm__ volatile ("sync");
+ }
+
+ return dramsize + dramsize2;
+}
+
+
+int checkboard (void)
+{
+ puts("Board: MarelV38B\n");
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_HW_WATCHDOG
+ /*
+ * Enable and configure the direction (output) of PSC3_9 - watchdog
+ * reset input. Refer to 7.3.2.2.[1,3,4] of the MPC5200B User's
+ * Manual.
+ */
+ *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC3_9;
+ *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC3_9;
+#endif /* CONFIG_HW_WATCHDOG */
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ /*
+ * Now, when we are in RAM, enable flash write access for the
+ * detection process. Note that CS_BOOT cannot be cleared when
+ * executing in flash.
+ */
+ *(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
+
+ /*
+ * Enable GPIO_WKUP_7 to "read the status of the actual power
+ * situation". Default direction is input, so no need to set it
+ * explicitly.
+ */
+ *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WKUP_7;
+ return 0;
+}
+
+extern void board_get_enetaddr(uchar *enetaddr);
+int misc_init_r(void)
+{
+ uchar enetaddr[6];
+
+ if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
+ board_get_enetaddr(enetaddr);
+ eth_setenv_enetaddr("ethaddr", enetaddr);
+ }
+
+ return 0;
+}
+
+#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
+void init_ide_reset(void)
+{
+ debug("init_ide_reset\n");
+
+ /* Configure PSC1_4 as GPIO output for ATA reset */
+ *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
+ *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
+ /* Deassert reset */
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
+}
+
+
+void ide_set_reset(int idereset)
+{
+ debug("ide_reset(%d)\n", idereset);
+
+ if (idereset) {
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
+ /* Make a delay. MPC5200 spec says 25 usec min */
+ udelay(500000);
+ } else
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
+}
+#endif
+
+
+#ifdef CONFIG_HW_WATCHDOG
+void hw_watchdog_reset(void)
+{
+ /*
+ * MarelV38B has a TPS3705 watchdog. Spec says that to kick the dog
+ * we need a positive or negative transition on WDI i.e., our PSC3_9.
+ */
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O ^= GPIO_PSC3_9;
+}
+#endif /* CONFIG_HW_WATCHDOG */
Code Review / kvmfornfv.git / blobdiff