--- /dev/null
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <config.h>
+#include <common.h>
+#include <mpc8xx.h>
+#include "pld.h"
+#include "hpi.h"
+
+#define _NOT_USED_ 0xFFFFFFFF
+
+static long int dram_size (long int, long int *, long int);
+
+const uint sdram_table[] = {
+ /*
+ * Single Read. (Offset 0 in UPMB RAM)
+ */
+ 0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
+ 0x1FF77C47, /* last */
+ /*
+ * SDRAM Initialization (offset 5 in UPMB RAM)
+ *
+ * This is no UPM entry point. The following definition uses
+ * the remaining space to establish an initialization
+ * sequence, which is executed by a RUN command.
+ *
+ */
+ 0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
+ /*
+ * Burst Read. (Offset 8 in UPMB RAM)
+ */
+ 0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
+ 0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Single Write. (Offset 18 in UPMB RAM)
+ */
+ 0x1F07FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Burst Write. (Offset 20 in UPMB RAM)
+ */
+ 0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
+ 0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
+ _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Refresh (Offset 30 in UPMB RAM)
+ */
+ 0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+ 0xFFFFFC84, 0xFFFFFC07, /* last */
+ _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Exception. (Offset 3c in UPMB RAM)
+ */
+ 0x7FFFFC07, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_,
+};
+
+phys_size_t initdram (int board_type)
+{
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+ volatile memctl8xx_t *memctl = &immr->im_memctl;
+ /* volatile spc1920_pld_t *pld = (spc1920_pld_t *) CONFIG_SYS_SPC1920_PLD_BASE; */
+
+ long int size_b0;
+ long int size8, size9;
+ int i;
+
+ /*
+ * Configure UPMB for SDRAM
+ */
+ upmconfig (UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
+
+ udelay(100);
+
+ memctl->memc_mptpr = CONFIG_SYS_MPTPR;
+
+ /* burst length=4, burst type=sequential, CAS latency=2 */
+ memctl->memc_mar = CONFIG_SYS_MAR;
+
+ /*
+ * Map controller bank 1 to the SDRAM bank at preliminary address.
+ */
+ memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
+ memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
+
+ /* initialize memory address register */
+ memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL; /* refresh not enabled yet */
+
+ /* mode initialization (offset 5) */
+ udelay (200); /* 0x80006105 */
+ memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x05);
+
+ /* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
+ udelay (1); /* 0x80006130 */
+ memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
+ udelay (1); /* 0x80006130 */
+ memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
+ udelay (1); /* 0x80006106 */
+ memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x06);
+
+ memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
+
+ udelay (200);
+
+ /* Need at least 10 DRAM accesses to stabilize */
+ for (i = 0; i < 10; ++i) {
+ volatile unsigned long *addr =
+ (volatile unsigned long *) CONFIG_SYS_SDRAM_BASE;
+ unsigned long val;
+
+ val = *(addr + i);
+ *(addr + i) = val;
+ }
+
+ /*
+ * Check Bank 0 Memory Size for re-configuration
+ *
+ * try 8 column mode
+ */
+ size8 = dram_size (CONFIG_SYS_MBMR_8COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
+
+ udelay (1000);
+
+ /*
+ * try 9 column mode
+ */
+ size9 = dram_size (CONFIG_SYS_MBMR_9COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
+
+ if (size8 < size9) { /* leave configuration at 9 columns */
+ size_b0 = size9;
+ memctl->memc_mbmr = CONFIG_SYS_MBMR_9COL | MBMR_PTBE;
+ udelay (500);
+ } else { /* back to 8 columns */
+ size_b0 = size8;
+ memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
+ udelay (500);
+ }
+
+ /*
+ * Final mapping:
+ */
+
+ memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) |
+ OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
+ memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
+ udelay (1000);
+
+ /* initalize the DSP Host Port Interface */
+ hpi_init();
+
+ /* FRAM Setup */
+ memctl->memc_or4 = CONFIG_SYS_OR4;
+ memctl->memc_br4 = CONFIG_SYS_BR4;
+ udelay(1000);
+
+ return (size_b0);
+}
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+static long int dram_size (long int mbmr_value, long int *base,
+ long int maxsize)
+{
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+ volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+ memctl->memc_mbmr = mbmr_value;
+
+ return (get_ram_size (base, maxsize));
+}
+
+
+/************* other stuff ******************/
+
+
+int board_early_init_f(void)
+{
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+
+ /* Set Go/NoGo led (PA15) to color red */
+ immap->im_ioport.iop_papar &= ~0x1;
+ immap->im_ioport.iop_paodr &= ~0x1;
+ immap->im_ioport.iop_padir |= 0x1;
+ immap->im_ioport.iop_padat |= 0x1;
+
+#if 0
+ /* Turn on LED PD9 */
+ immap->im_ioport.iop_pdpar &= ~(0x0040);
+ immap->im_ioport.iop_pddir |= 0x0040;
+ immap->im_ioport.iop_pddat |= 0x0040;
+#endif
+
+ /*
+ * Enable console on SMC1. This requires turning on
+ * the com2_en signal and SMC1_DISABLE
+ */
+
+ /* SMC1_DISABLE: PB17 */
+ immap->im_cpm.cp_pbodr &= ~0x4000;
+ immap->im_cpm.cp_pbpar &= ~0x4000;
+ immap->im_cpm.cp_pbdir |= 0x4000;
+ immap->im_cpm.cp_pbdat &= ~0x4000;
+
+ /* COM2_EN: PD10 */
+ immap->im_ioport.iop_pdpar &= ~0x0020;
+ immap->im_ioport.iop_pddir &= ~0x4000;
+ immap->im_ioport.iop_pddir |= 0x0020;
+ immap->im_ioport.iop_pddat |= 0x0020;
+
+
+#ifdef CONFIG_SYS_SMC1_PLD_CLK4 /* SMC1 uses CLK4 from PLD */
+ immap->im_cpm.cp_simode |= 0x7000;
+ immap->im_cpm.cp_simode &= ~(0x8000);
+#endif
+
+ return 0;
+}
+
+int last_stage_init(void)
+{
+#ifdef CONFIG_SPC1920_HPI_TEST
+ printf("CMB1920 Host Port Interface Test: %s\n",
+ hpi_test() ? "Failed!" : "OK");
+#endif
+ return 0;
+}
+
+int checkboard (void)
+{
+ puts("Board: SPC1920\n");
+ return 0;
+}
Code Review / kvmfornfv.git / blobdiff