--- /dev/null
+/*
+ * SanDisk Sansa Fuze Plus board
+ *
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * Hardware investigation done by:
+ *
+ * Amaury Pouly <amaury.pouly@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx23.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+ /* IO0 clock at 480MHz */
+ mxs_set_ioclk(MXC_IOCLK0, 480000);
+
+ /* SSP0 clock at 96MHz */
+ mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ return mxs_dram_init();
+}
+
+#ifdef CONFIG_CMD_MMC
+static int xfi3_mmc_cd(int id)
+{
+ switch (id) {
+ case 0:
+ /* The SSP_DETECT is inverted on this board. */
+ return gpio_get_value(MX23_PAD_SSP1_DETECT__GPIO_2_1);
+ case 1:
+ /* Internal eMMC always present */
+ return 1;
+ default:
+ return 0;
+ }
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+
+ /* MicroSD slot */
+ gpio_direction_input(MX23_PAD_SSP1_DETECT__GPIO_2_1);
+ gpio_direction_output(MX23_PAD_GPMI_D08__GPIO_0_8, 0);
+ ret = mxsmmc_initialize(bis, 0, NULL, xfi3_mmc_cd);
+ if (ret)
+ return ret;
+
+ /* Internal eMMC */
+ gpio_direction_output(MX23_PAD_PWM3__GPIO_1_29, 0);
+ ret = mxsmmc_initialize(bis, 1, NULL, xfi3_mmc_cd);
+
+ return ret;
+}
+#endif
+
+#ifdef CONFIG_VIDEO_MXS
+#define MUX_CONFIG_LCD (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL)
+const iomux_cfg_t iomux_lcd_gpio[] = {
+ MX23_PAD_LCD_D00__GPIO_1_0 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D01__GPIO_1_1 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D02__GPIO_1_2 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D03__GPIO_1_3 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D04__GPIO_1_4 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D05__GPIO_1_5 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D06__GPIO_1_6 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D07__GPIO_1_7 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D08__GPIO_1_8 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D09__GPIO_1_9 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D10__GPIO_1_10 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D11__GPIO_1_11 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D12__GPIO_1_12 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D13__GPIO_1_13 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D14__GPIO_1_14 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D15__GPIO_1_15 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D16__GPIO_1_16 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D17__GPIO_1_17 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_RESET__GPIO_1_18 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_RS__GPIO_1_19 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_WR__GPIO_1_20 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_CS__GPIO_1_21 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_ENABLE__GPIO_1_23 | MUX_CONFIG_LCD,
+};
+
+const iomux_cfg_t iomux_lcd_lcd[] = {
+ MX23_PAD_LCD_D00__LCD_D00 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D01__LCD_D01 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D02__LCD_D02 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D03__LCD_D03 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D04__LCD_D04 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D05__LCD_D05 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D06__LCD_D06 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D07__LCD_D07 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D08__LCD_D08 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D09__LCD_D09 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D10__LCD_D10 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D11__LCD_D11 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D12__LCD_D12 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D13__LCD_D13 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D14__LCD_D14 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D15__LCD_D15 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D16__LCD_D16 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_D17__LCD_D17 | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_RESET__LCD_RESET | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_RS__LCD_RS | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_WR__LCD_WR | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_CS__LCD_CS | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_ENABLE__LCD_ENABLE | MUX_CONFIG_LCD,
+ MX23_PAD_LCD_VSYNC__LCD_VSYNC | MUX_CONFIG_LCD,
+};
+
+static int mxsfb_read_register(uint32_t reg, uint32_t *value)
+{
+ iomux_cfg_t mux;
+ uint32_t val = 0;
+ int i;
+
+ /* Mangle the register offset. */
+ reg = ((reg & 0xff) << 1) | (((reg >> 8) & 0xff) << 10);
+
+ /*
+ * The SmartLCD interface on MX233 can only do WRITE operation
+ * via the LCDIF controller. Implement the READ operation by
+ * fiddling with bits.
+ */
+ mxs_iomux_setup_multiple_pads(iomux_lcd_gpio,
+ ARRAY_SIZE(iomux_lcd_gpio));
+
+ gpio_direction_output(MX23_PAD_LCD_RS__GPIO_1_19, 1);
+ gpio_direction_output(MX23_PAD_LCD_CS__GPIO_1_21, 1);
+ gpio_direction_output(MX23_PAD_LCD_WR__GPIO_1_20, 1);
+ gpio_direction_output(MX23_PAD_LCD_ENABLE__GPIO_1_23, 1);
+
+ for (i = 0; i < 18; i++) {
+ mux = MXS_IOMUX_PAD_NAKED(1, i, PAD_MUXSEL_GPIO);
+ gpio_direction_output(mux, 0);
+ }
+
+ udelay(2);
+ gpio_direction_output(MX23_PAD_LCD_RS__GPIO_1_19, 0);
+ udelay(1);
+ gpio_direction_output(MX23_PAD_LCD_CS__GPIO_1_21, 0);
+ udelay(1);
+ gpio_direction_output(MX23_PAD_LCD_WR__GPIO_1_20, 0);
+ udelay(1);
+
+ for (i = 0; i < 18; i++) {
+ mux = MXS_IOMUX_PAD_NAKED(1, i, PAD_MUXSEL_GPIO);
+ gpio_direction_output(mux, (reg >> i) & 1);
+ }
+ udelay(1);
+
+ gpio_direction_output(MX23_PAD_LCD_WR__GPIO_1_20, 1);
+ udelay(3);
+
+ for (i = 0; i < 18; i++) {
+ mux = MXS_IOMUX_PAD_NAKED(1, i, PAD_MUXSEL_GPIO);
+ gpio_direction_input(mux);
+ }
+ udelay(2);
+
+ gpio_direction_output(MX23_PAD_LCD_ENABLE__GPIO_1_23, 0);
+ udelay(1);
+ gpio_direction_output(MX23_PAD_LCD_RS__GPIO_1_19, 1);
+ udelay(1);
+ gpio_direction_output(MX23_PAD_LCD_ENABLE__GPIO_1_23, 1);
+ udelay(3);
+ gpio_direction_output(MX23_PAD_LCD_ENABLE__GPIO_1_23, 0);
+ udelay(2);
+
+ for (i = 0; i < 18; i++) {
+ mux = MXS_IOMUX_PAD_NAKED(1, i, PAD_MUXSEL_GPIO);
+ val |= !!gpio_get_value(mux) << i;
+ }
+ udelay(1);
+
+ gpio_direction_output(MX23_PAD_LCD_ENABLE__GPIO_1_23, 1);
+ udelay(1);
+ gpio_direction_output(MX23_PAD_LCD_CS__GPIO_1_21, 1);
+ udelay(1);
+
+ mxs_iomux_setup_multiple_pads(iomux_lcd_lcd,
+ ARRAY_SIZE(iomux_lcd_lcd));
+
+ /* Demangle the register value. */
+ *value = ((val >> 1) & 0xff) | ((val >> 2) & 0xff00);
+
+ writel(val, 0x2000);
+ return 0;
+}
+
+static int mxsfb_write_byte(uint32_t payload, const unsigned int data)
+{
+ struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE;
+ const unsigned int timeout = 0x10000;
+
+ /* What is going on here I do not know. FIXME */
+ payload = ((payload & 0xff) << 1) | (((payload >> 8) & 0xff) << 10);
+
+ if (mxs_wait_mask_clr(®s->hw_lcdif_ctrl_reg, LCDIF_CTRL_RUN,
+ timeout))
+ return -ETIMEDOUT;
+
+ writel((1 << LCDIF_TRANSFER_COUNT_V_COUNT_OFFSET) |
+ (1 << LCDIF_TRANSFER_COUNT_H_COUNT_OFFSET),
+ ®s->hw_lcdif_transfer_count);
+
+ writel(LCDIF_CTRL_DATA_SELECT | LCDIF_CTRL_RUN,
+ ®s->hw_lcdif_ctrl_clr);
+
+ if (data)
+ writel(LCDIF_CTRL_DATA_SELECT, ®s->hw_lcdif_ctrl_set);
+
+ writel(LCDIF_CTRL_RUN, ®s->hw_lcdif_ctrl_set);
+
+ if (mxs_wait_mask_clr(®s->hw_lcdif_lcdif_stat_reg, 1 << 29,
+ timeout))
+ return -ETIMEDOUT;
+
+ writel(payload, ®s->hw_lcdif_data);
+ return mxs_wait_mask_clr(®s->hw_lcdif_ctrl_reg, LCDIF_CTRL_RUN,
+ timeout);
+}
+
+static void mxsfb_write_register(uint32_t reg, uint32_t data)
+{
+ mxsfb_write_byte(reg, 0);
+ mxsfb_write_byte(data, 1);
+}
+
+static const struct {
+ uint8_t reg;
+ uint8_t delay;
+ uint16_t val;
+} lcd_regs[] = {
+ { 0xe5, 0 , 0x78f0 },
+ { 0xe3, 0 , 0x3008 },
+ { 0xe7, 0 , 0x0012 },
+ { 0xef, 0 , 0x1231 },
+ { 0x00, 0 , 0x0001 },
+ { 0x01, 0 , 0x0100 },
+ { 0x02, 0 , 0x0700 },
+ { 0x03, 0 , 0x1030 },
+ { 0x04, 0 , 0x0000 },
+ { 0x08, 0 , 0x0207 },
+ { 0x09, 0 , 0x0000 },
+ { 0x0a, 0 , 0x0000 },
+ { 0x0c, 0 , 0x0000 },
+ { 0x0d, 0 , 0x0000 },
+ { 0x0f, 0 , 0x0000 },
+ { 0x10, 0 , 0x0000 },
+ { 0x11, 0 , 0x0007 },
+ { 0x12, 0 , 0x0000 },
+ { 0x13, 20 , 0x0000 },
+ /* Wait 20 mS here. */
+ { 0x10, 0 , 0x1290 },
+ { 0x11, 50 , 0x0007 },
+ /* Wait 50 mS here. */
+ { 0x12, 50 , 0x0019 },
+ /* Wait 50 mS here. */
+ { 0x13, 0 , 0x1700 },
+ { 0x29, 50 , 0x0014 },
+ /* Wait 50 mS here. */
+ { 0x20, 0 , 0x0000 },
+ { 0x21, 0 , 0x0000 },
+ { 0x30, 0 , 0x0504 },
+ { 0x31, 0 , 0x0007 },
+ { 0x32, 0 , 0x0006 },
+ { 0x35, 0 , 0x0106 },
+ { 0x36, 0 , 0x0202 },
+ { 0x37, 0 , 0x0504 },
+ { 0x38, 0 , 0x0500 },
+ { 0x39, 0 , 0x0706 },
+ { 0x3c, 0 , 0x0204 },
+ { 0x3d, 0 , 0x0202 },
+ { 0x50, 0 , 0x0000 },
+ { 0x51, 0 , 0x00ef },
+ { 0x52, 0 , 0x0000 },
+ { 0x53, 0 , 0x013f },
+ { 0x60, 0 , 0xa700 },
+ { 0x61, 0 , 0x0001 },
+ { 0x6a, 0 , 0x0000 },
+ { 0x2b, 50 , 0x000d },
+ /* Wait 50 mS here. */
+ { 0x90, 0 , 0x0011 },
+ { 0x92, 0 , 0x0600 },
+ { 0x93, 0 , 0x0003 },
+ { 0x95, 0 , 0x0110 },
+ { 0x97, 0 , 0x0000 },
+ { 0x98, 0 , 0x0000 },
+ { 0x07, 0 , 0x0173 },
+};
+
+void board_mxsfb_system_setup(void)
+{
+ struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE;
+ uint32_t id;
+ int i;
+
+ /* Switch the LCDIF into System-Mode */
+ writel(LCDIF_CTRL_LCDIF_MASTER | LCDIF_CTRL_DOTCLK_MODE |
+ LCDIF_CTRL_BYPASS_COUNT, ®s->hw_lcdif_ctrl_clr);
+
+ /* To program the LCD, switch to 18bit bus + 18bit data. */
+ clrsetbits_le32(®s->hw_lcdif_ctrl,
+ LCDIF_CTRL_WORD_LENGTH_MASK | LCDIF_CTRL_LCD_DATABUS_WIDTH_MASK,
+ LCDIF_CTRL_WORD_LENGTH_18BIT |
+ LCDIF_CTRL_LCD_DATABUS_WIDTH_18BIT);
+
+ mxsfb_read_register(0, &id);
+ writel(id, 0x2004);
+
+ /* Restart the SmartLCD controller */
+ mdelay(50);
+ writel(1, ®s->hw_lcdif_ctrl1_set);
+ mdelay(50);
+ writel(1, ®s->hw_lcdif_ctrl1_clr);
+ mdelay(50);
+ writel(1, ®s->hw_lcdif_ctrl1_set);
+ mdelay(50);
+
+ /* Program the SmartLCD controller */
+ writel(LCDIF_CTRL1_RECOVER_ON_UNDERFLOW, ®s->hw_lcdif_ctrl1_set);
+
+ writel((0x02 << LCDIF_TIMING_CMD_HOLD_OFFSET) |
+ (0x02 << LCDIF_TIMING_CMD_SETUP_OFFSET) |
+ (0x02 << LCDIF_TIMING_DATA_HOLD_OFFSET) |
+ (0x01 << LCDIF_TIMING_DATA_SETUP_OFFSET),
+ ®s->hw_lcdif_timing);
+
+ /*
+ * ILI9325 init and configuration sequence.
+ */
+ for (i = 0; i < ARRAY_SIZE(lcd_regs); i++) {
+ mxsfb_write_register(lcd_regs[i].reg, lcd_regs[i].val);
+ if (lcd_regs[i].delay)
+ mdelay(lcd_regs[i].delay);
+ }
+ /* Turn on Framebuffer Upload Mode */
+ mxsfb_write_byte(0x22, 0);
+
+ writel(LCDIF_CTRL_LCDIF_MASTER | LCDIF_CTRL_DATA_SELECT,
+ ®s->hw_lcdif_ctrl_set);
+
+ /* Operate the framebuffer in 16bit mode. */
+ clrsetbits_le32(®s->hw_lcdif_ctrl,
+ LCDIF_CTRL_WORD_LENGTH_MASK | LCDIF_CTRL_LCD_DATABUS_WIDTH_MASK,
+ LCDIF_CTRL_WORD_LENGTH_16BIT |
+ LCDIF_CTRL_LCD_DATABUS_WIDTH_18BIT);
+}
+#endif
+
+int board_init(void)
+{
+ /* Adress of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ /* Turn on PWM backlight */
+ gpio_direction_output(MX23_PAD_PWM2__GPIO_1_28, 1);
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ usb_eth_initialize(bis);
+ return 0;
+}
Code Review / kvmfornfv.git / blobdiff