--- /dev/null
+/*
+ * (C) Copyright 2013 SAMSUNG Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <cros_ec.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <spi.h>
+#include <tmu.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/board.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <power/pmic.h>
+#include <asm/arch/sromc.h>
+#include <lcd.h>
+#include <samsung/misc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int __exynos_early_init_f(void)
+{
+ return 0;
+}
+int exynos_early_init_f(void)
+ __attribute__((weak, alias("__exynos_early_init_f")));
+
+int __exynos_power_init(void)
+{
+ return 0;
+}
+int exynos_power_init(void)
+ __attribute__((weak, alias("__exynos_power_init")));
+
+#if defined CONFIG_EXYNOS_TMU
+/* Boot Time Thermal Analysis for SoC temperature threshold breach */
+static void boot_temp_check(void)
+{
+ int temp;
+
+ switch (tmu_monitor(&temp)) {
+ case TMU_STATUS_NORMAL:
+ break;
+ case TMU_STATUS_TRIPPED:
+ /*
+ * Status TRIPPED ans WARNING means corresponding threshold
+ * breach
+ */
+ puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n");
+ set_ps_hold_ctrl();
+ hang();
+ break;
+ case TMU_STATUS_WARNING:
+ puts("EXYNOS_TMU: WARNING! Temperature very high\n");
+ break;
+ case TMU_STATUS_INIT:
+ /*
+ * TMU_STATUS_INIT means something is wrong with temperature
+ * sensing and TMU status was changed back from NORMAL to INIT.
+ */
+ puts("EXYNOS_TMU: WARNING! Temperature sensing not done\n");
+ break;
+ default:
+ debug("EXYNOS_TMU: Unknown TMU state\n");
+ }
+}
+#endif
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+#if defined CONFIG_EXYNOS_TMU
+ if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) {
+ debug("%s: Failed to init TMU\n", __func__);
+ return -1;
+ }
+ boot_temp_check();
+#endif
+
+#ifdef CONFIG_EXYNOS_SPI
+ spi_init();
+#endif
+ return exynos_init();
+}
+
+int dram_init(void)
+{
+ int i;
+ u32 addr;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+ gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+ }
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ int i;
+ u32 addr, size;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+ size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+
+ gd->bd->bi_dram[i].start = addr;
+ gd->bd->bi_dram[i].size = size;
+ }
+}
+
+static int board_uart_init(void)
+{
+ int err, uart_id, ret = 0;
+
+ for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
+ err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("UART%d not configured\n",
+ (uart_id - PERIPH_ID_UART0));
+ ret |= err;
+ }
+ }
+ return ret;
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+ int err;
+
+ err = board_uart_init();
+ if (err) {
+ debug("UART init failed\n");
+ return err;
+ }
+
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+ board_i2c_init(gd->fdt_blob);
+#endif
+
+ return exynos_early_init_f();
+}
+#endif
+
+#if defined(CONFIG_POWER)
+int power_init_board(void)
+{
+ set_ps_hold_ctrl();
+
+ return exynos_power_init();
+}
+#endif
+
+#ifdef CONFIG_OF_CONTROL
+#ifdef CONFIG_SMC911X
+static int decode_sromc(const void *blob, struct fdt_sromc *config)
+{
+ int err;
+ int node;
+
+ node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
+ if (node < 0) {
+ debug("Could not find SROMC node\n");
+ return node;
+ }
+
+ config->bank = fdtdec_get_int(blob, node, "bank", 0);
+ config->width = fdtdec_get_int(blob, node, "width", 2);
+
+ err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
+ FDT_SROM_TIMING_COUNT);
+ if (err < 0) {
+ debug("Could not decode SROMC configuration Error: %s\n",
+ fdt_strerror(err));
+ return -FDT_ERR_NOTFOUND;
+ }
+ return 0;
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_SMC911X
+ u32 smc_bw_conf, smc_bc_conf;
+ struct fdt_sromc config;
+ fdt_addr_t base_addr;
+ int node;
+
+ node = decode_sromc(gd->fdt_blob, &config);
+ if (node < 0) {
+ debug("%s: Could not find sromc configuration\n", __func__);
+ return 0;
+ }
+ node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
+ if (node < 0) {
+ debug("%s: Could not find lan9215 configuration\n", __func__);
+ return 0;
+ }
+
+ /* We now have a node, so any problems from now on are errors */
+ base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
+ if (base_addr == FDT_ADDR_T_NONE) {
+ debug("%s: Could not find lan9215 address\n", __func__);
+ return -1;
+ }
+
+ /* Ethernet needs data bus width of 16 bits */
+ if (config.width != 2) {
+ debug("%s: Unsupported bus width %d\n", __func__,
+ config.width);
+ return -1;
+ }
+ smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
+ | SROMC_BYTE_ENABLE(config.bank);
+
+ smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |
+ SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |
+ SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |
+ SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |
+ SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |
+ SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |
+ SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
+
+ /* Select and configure the SROMC bank */
+ exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
+ s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
+ return smc911x_initialize(0, base_addr);
+#endif
+ return 0;
+}
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+
+#ifdef CONFIG_SDHCI
+ /* mmc initializattion for available channels */
+ ret = exynos_mmc_init(gd->fdt_blob);
+ if (ret)
+ debug("mmc init failed\n");
+#endif
+#ifdef CONFIG_DWMMC
+ /* dwmmc initializattion for available channels */
+ ret = exynos_dwmmc_init(gd->fdt_blob);
+ if (ret)
+ debug("dwmmc init failed\n");
+#endif
+
+ return ret;
+}
+#endif
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+ const char *board_name;
+
+ board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
+ printf("Board: %s\n", board_name ? board_name : "unknown");
+
+ return 0;
+}
+#endif
+#endif /* CONFIG_OF_CONTROL */
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+ stdio_print_current_devices();
+
+ if (cros_ec_get_error()) {
+ /* Force console on */
+ gd->flags &= ~GD_FLG_SILENT;
+
+ printf("cros-ec communications failure %d\n",
+ cros_ec_get_error());
+ puts("\nPlease reset with Power+Refresh\n\n");
+ panic("Cannot init cros-ec device");
+ return -1;
+ }
+ return 0;
+}
+#endif
+
+int arch_early_init_r(void)
+{
+#ifdef CONFIG_CROS_EC
+ if (cros_ec_board_init()) {
+ printf("%s: Failed to init EC\n", __func__);
+ return 0;
+ }
+#endif
+
+ return 0;
+}
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ set_board_info();
+#endif
+#ifdef CONFIG_LCD_MENU
+ keys_init();
+ check_boot_mode();
+#endif
+#ifdef CONFIG_CMD_BMP
+ if (panel_info.logo_on)
+ draw_logo();
+#endif
+ return 0;
+}
+#endif
Code Review / kvmfornfv.git / blobdiff