Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / board / nvidia / whistler / whistler.c

diff --git a/qemu/roms/u-boot/board/nvidia/whistler/whistler.c b/qemu/roms/u-boot/board/nvidia/whistler/whistler.c
new file mode 100644 (file)
index 0000000..3e9d3d9
--- /dev/null
+++ b/qemu/roms/u-boot/board/nvidia/whistler/whistler.c
@@ -0,0 +1,73 @@
+/*
+ *  (C) Copyright 2010-2012
+ *  NVIDIA Corporation <www.nvidia.com>
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/tegra.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/funcmux.h>
+#include <asm/arch/pinmux.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+
+#ifdef CONFIG_TEGRA_MMC
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the pin muxes/tristate values for the SDMMC(s)
+ */
+void pin_mux_mmc(void)
+{
+       uchar val;
+       int ret;
+
+       /* Turn on MAX8907B LDO12 to 2.8V for J40 power */
+       ret = i2c_set_bus_num(0);
+       if (ret)
+               printf("i2c_set_bus_num failed: %d\n", ret);
+       val = 0x29;
+       ret = i2c_write(0x3c, 0x46, 1, &val, 1);
+       if (ret)
+               printf("i2c_write 0 0x3c 0x46 failed: %d\n", ret);
+       val = 0x00;
+       ret = i2c_write(0x3c, 0x45, 1, &val, 1);
+       if (ret)
+               printf("i2c_write 0 0x3c 0x45 failed: %d\n", ret);
+       val = 0x1f;
+       ret = i2c_write(0x3c, 0x44, 1, &val, 1);
+       if (ret)
+               printf("i2c_write 0 0x3c 0x44 failed: %d\n", ret);
+
+       funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_SLXA_8BIT);
+       funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATC_ATD_8BIT);
+}
+#endif
+
+/* this is a weak define that we are overriding */
+void pin_mux_usb(void)
+{
+       uchar val;
+       int ret;
+
+       /*
+        * This is a hack. This should be represented in DT using the
+        * vbus-gpio property. However, U-Boot's DT support doesn't
+        * support any GPIO controller other than the Tegra's yet.
+        */
+
+       /* Turn on TAC6416's GPIO 0+1 for USB1/3's VBUS */
+       ret = i2c_set_bus_num(0);
+       if (ret)
+               printf("i2c_set_bus_num failed: %d\n", ret);
+       val = 0x03;
+       ret = i2c_write(0x20, 2, 1, &val, 1);
+       if (ret)
+               printf("i2c_write 0 0x20 2 failed: %d\n", ret);
+       val = 0xfc;
+       ret = i2c_write(0x20, 6, 1, &val, 1);
+       if (ret)
+               printf("i2c_write 0 0x20 6 failed: %d\n", ret);
+}