Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / board / keymile / kmp204x / pci.c

diff --git a/qemu/roms/u-boot/board/keymile/kmp204x/pci.c b/qemu/roms/u-boot/board/keymile/kmp204x/pci.c
new file mode 100644 (file)
index 0000000..2b0b054
--- /dev/null
+++ b/qemu/roms/u-boot/board/keymile/kmp204x/pci.c
@@ -0,0 +1,123 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp@keymile.com>
+ *
+ * Copyright 2007-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+#include <asm/errno.h>
+
+#include "kmp204x.h"
+
+#define PROM_SEL_L     11
+/* control the PROM_SEL_L signal*/
+static void toggle_fpga_eeprom_bus(bool cpu_own)
+{
+       qrio_gpio_direction_output(GPIO_A, PROM_SEL_L, !cpu_own);
+}
+
+#define CONF_SEL_L     10
+#define FPGA_PROG_L    19
+#define FPGA_DONE      18
+#define FPGA_INIT_L    17
+
+int trigger_fpga_config(void)
+{
+       int ret = 0, init_l;
+       /* approx 10ms */
+       u32 timeout = 10000;
+
+       /* make sure the FPGA_can access the EEPROM */
+       toggle_fpga_eeprom_bus(false);
+
+       /* assert CONF_SEL_L to be able to drive FPGA_PROG_L */
+       qrio_gpio_direction_output(GPIO_A, CONF_SEL_L, 0);
+
+       /* trigger the config start */
+       qrio_gpio_direction_output(GPIO_A, FPGA_PROG_L, 0);
+
+       /* small delay for INIT_L line */
+       udelay(10);
+
+       /* wait for FPGA_INIT to be asserted */
+       do {
+               init_l = qrio_get_gpio(GPIO_A, FPGA_INIT_L);
+               if (timeout-- == 0) {
+                       printf("FPGA_INIT timeout\n");
+                       ret = -EFAULT;
+                       break;
+               }
+               udelay(10);
+       } while (init_l);
+
+       /* deassert FPGA_PROG, config should start */
+       qrio_set_gpio(GPIO_A, FPGA_PROG_L, 1);
+
+       return ret;
+}
+
+/* poll the FPGA_DONE signal and give the EEPROM back to the QorIQ */
+static int wait_for_fpga_config(void)
+{
+       int ret = 0, done;
+       /* approx 5 s */
+       u32 timeout = 500000;
+
+       printf("PCIe FPGA config:");
+       do {
+               done = qrio_get_gpio(GPIO_A, FPGA_DONE);
+               if (timeout-- == 0) {
+                       printf(" FPGA_DONE timeout\n");
+                       ret = -EFAULT;
+                       goto err_out;
+               }
+               udelay(10);
+       } while (!done);
+
+       printf(" done\n");
+
+err_out:
+       /* deactive CONF_SEL and give the CPU conf EEPROM access */
+       qrio_set_gpio(GPIO_A, CONF_SEL_L, 1);
+       toggle_fpga_eeprom_bus(true);
+
+       return ret;
+}
+
+#define PCIE_SW_RST    14
+#define PEXHC_RST      13
+#define HOOPER_RST     12
+
+void pci_init_board(void)
+{
+       qrio_prstcfg(PCIE_SW_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+       qrio_prstcfg(PEXHC_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+       qrio_prstcfg(HOOPER_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+
+       /* wait for the PCIe FPGA to be configured
+        * it has been triggered earlier in board_early_init_r */
+       if (wait_for_fpga_config())
+               printf("error finishing PCIe FPGA config\n");
+
+       qrio_prst(PCIE_SW_RST, false, false);
+       qrio_prst(PEXHC_RST, false, false);
+       qrio_prst(HOOPER_RST, false, false);
+       /* Hooper is not direcly PCIe capable */
+       mdelay(50);
+
+       fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+       FT_FSL_PCI_SETUP;
+}