--- /dev/null
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp@keymile.com>
+ *
+ * Copyright 2011,2012 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "../common/common.h"
+#include "kmp204x.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ printf("Board: Keymile %s\n", CONFIG_KM_BOARD_NAME);
+
+ return 0;
+}
+
+/* I2C deblocking uses the algorithm defined in board/keymile/common/common.c
+ * 2 dedicated QRIO GPIOs externally pull the SCL and SDA lines
+ * For I2C only the low state is activly driven and high state is pulled-up
+ * by a resistor. Therefore the deblock GPIOs are used
+ * -> as an active output to drive a low state
+ * -> as an open-drain input to have a pulled-up high state
+ */
+
+/* QRIO GPIOs used for deblocking */
+#define DEBLOCK_PORT1 GPIO_A
+#define DEBLOCK_SCL1 20
+#define DEBLOCK_SDA1 21
+
+/* By default deblock GPIOs are floating */
+static void i2c_deblock_gpio_cfg(void)
+{
+ /* set I2C bus 1 deblocking GPIOs input, but 0 value for open drain */
+ qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SCL1);
+ qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SDA1);
+
+ qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, 0);
+ qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, 0);
+}
+
+void set_sda(int state)
+{
+ qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, state);
+}
+
+void set_scl(int state)
+{
+ qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, state);
+}
+
+int get_sda(void)
+{
+ return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1);
+}
+
+int get_scl(void)
+{
+ return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1);
+}
+
+
+#define ZL30158_RST 8
+#define BFTIC4_RST 0
+
+int board_early_init_f(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ /* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */
+ setbits_be32(&gur->ddrclkdr, 0x001f000f);
+
+ /* set the BFTIC's prstcfg to reset at power-up and unit reset only */
+ qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST);
+ /* and enable WD on it */
+ qrio_wdmask(BFTIC4_RST, true);
+
+ /* set the ZL30138's prstcfg to reset at power-up and unit reset only */
+ qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_UNIT_RST);
+ /* and take it out of reset as soon as possible (needed for Hooper) */
+ qrio_prst(ZL30158_RST, false, false);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ int ret = 0;
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ set_liodns();
+ setup_portals();
+
+ ret = trigger_fpga_config();
+ if (ret)
+ printf("error triggering PCIe FPGA config\n");
+
+ /* enable the Unit LED (red) & Boot LED (on) */
+ qrio_set_leds();
+
+ /* enable Application Buffer */
+ qrio_enable_app_buffer();
+
+ return ret;
+}
+
+unsigned long get_board_sys_clk(unsigned long dummy)
+{
+ return 66666666;
+}
+
+#define ETH_FRONT_PHY_RST 15
+#define QSFP2_RST 11
+#define QSFP1_RST 10
+#define ZL30343_RST 9
+
+int misc_init_f(void)
+{
+ /* configure QRIO pis for i2c deblocking */
+ i2c_deblock_gpio_cfg();
+
+ /* configure the front phy's prstcfg and take it out of reset */
+ qrio_prstcfg(ETH_FRONT_PHY_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+ qrio_prst(ETH_FRONT_PHY_RST, false, false);
+
+ /* set the ZL30343 prstcfg to reset at power-up and unit reset only */
+ qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_UNIT_RST);
+ /* and enable the WD on it */
+ qrio_wdmask(ZL30343_RST, true);
+
+ /* set the QSFPs' prstcfg to reset at power-up and unit rst only */
+ qrio_prstcfg(QSFP1_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_prstcfg(QSFP2_RST, PRSTCFG_POWUP_UNIT_RST);
+
+ /* and enable the WD on them */
+ qrio_wdmask(QSFP1_RST, true);
+ qrio_wdmask(QSFP2_RST, true);
+
+ return 0;
+}
+
+#define NUM_SRDS_BANKS 2
+
+int misc_init_r(void)
+{
+ serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+ u32 expected[NUM_SRDS_BANKS] = {SRDS_PLLCR0_RFCK_SEL_100,
+ SRDS_PLLCR0_RFCK_SEL_125};
+ unsigned int i;
+
+ /* check SERDES reference clocks */
+ for (i = 0; i < NUM_SRDS_BANKS; i++) {
+ u32 actual = in_be32(®s->bank[i].pllcr0);
+ actual &= SRDS_PLLCR0_RFCK_SEL_MASK;
+ if (actual != expected[i]) {
+ printf("Warning: SERDES bank %u expects reference \
+ clock %sMHz, but actual is %sMHz\n", i + 1,
+ serdes_clock_to_string(expected[i]),
+ serdes_clock_to_string(actual));
+ }
+ }
+
+ return 0;
+}
+
+#if defined(CONFIG_HUSH_INIT_VAR)
+int hush_init_var(void)
+{
+ ivm_read_eeprom();
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_LAST_STAGE_INIT)
+
+int last_stage_init(void)
+{
+#if defined(CONFIG_KMCOGE4)
+ /* on KMCOGE4, the BFTIC4 is on the LBAPP2 */
+ struct bfticu_iomap *bftic4 =
+ (struct bfticu_iomap *)CONFIG_SYS_LBAPP2_BASE;
+ u8 dip_switch = in_8((u8 *)&(bftic4->mswitch)) & BFTICU_DIPSWITCH_MASK;
+
+ if (dip_switch != 0) {
+ /* start bootloader */
+ puts("DIP: Enabled\n");
+ setenv("actual_bank", "0");
+ }
+#endif
+ set_km_env();
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+void fdt_fixup_fman_mac_addresses(void *blob)
+{
+ int node, i, ret;
+ char *tmp, *end;
+ unsigned char mac_addr[6];
+
+ /* get the mac addr from env */
+ tmp = getenv("ethaddr");
+ if (!tmp) {
+ printf("ethaddr env variable not defined\n");
+ return;
+ }
+ for (i = 0; i < 6; i++) {
+ mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0;
+ if (tmp)
+ tmp = (*end) ? end+1 : end;
+ }
+
+ /* find the correct fdt ethernet path and correct it */
+ node = fdt_path_offset(blob, "/soc/fman/ethernet@e8000");
+ if (node < 0) {
+ printf("no /soc/fman/ethernet path offset\n");
+ return;
+ }
+ ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6);
+ if (ret) {
+ printf("error setting local-mac-address property\n");
+ return;
+ }
+}
+#endif
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_fman_mac_addresses(blob);
+#endif
+}
+
+#if defined(CONFIG_POST)
+
+/* DIC26_SELFTEST GPIO used to start factory test sw */
+#define SELFTEST_PORT GPIO_A
+#define SELFTEST_PIN 31
+
+int post_hotkeys_pressed(void)
+{
+ qrio_gpio_direction_input(SELFTEST_PORT, SELFTEST_PIN);
+ return qrio_get_gpio(SELFTEST_PORT, SELFTEST_PIN);
+}
+#endif
Code Review / kvmfornfv.git / blobdiff