--- /dev/null
+/*
+ * (C) Copyright 2000, 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * Ulrich Lutz, Speech Design GmbH, ulutz@datalab.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc8xx.h>
+#include <commproc.h>
+
+#ifdef CONFIG_STATUS_LED
+# include <status_led.h>
+#endif
+
+/* ------------------------------------------------------------------------- */
+
+static long int dram_size (long int, long int *, long int);
+
+/* ------------------------------------------------------------------------- */
+
+#define _NOT_USED_ 0xFFFFFFFF
+
+/*
+ * 50 MHz SHARC access using UPM A
+ */
+const uint sharc_table[] = {
+ /*
+ * Single Read. (Offset 0 in UPM RAM)
+ */
+ 0x0FF3FC04, 0x0FF3EC00, 0x7FFFEC04, 0xFFFFEC04,
+ 0xFFFFEC05, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Burst Read. (Offset 8 in UPM RAM)
+ */
+ /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Single Write. (Offset 18 in UPM RAM)
+ */
+ 0x0FAFFC04, 0x0FAFEC00, 0x7FFFEC04, 0xFFFFEC04,
+ 0xFFFFEC05, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Burst Write. (Offset 20 in UPM RAM)
+ */
+ /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Refresh (Offset 30 in UPM RAM)
+ */
+ /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Exception. (Offset 3c in UPM RAM)
+ */
+ 0x7FFFFC07, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_,
+};
+
+
+/*
+ * 50 MHz SDRAM access using UPM B
+ */
+const uint sdram_table[] = {
+ /*
+ * Single Read. (Offset 0 in UPM RAM)
+ */
+ 0x0E26FC04, 0x11ADFC04, 0xEFBBBC00, 0x1FF77C45, /* last */
+ _NOT_USED_,
+ /*
+ * SDRAM Initialization (offset 5 in UPM RAM)
+ *
+ * This is no UPM entry point. The following definition uses
+ * the remaining space to establish an initialization
+ * sequence, which is executed by a RUN command.
+ *
+ */
+ 0x1FF77C35, 0xEFEABC34, 0x1FB57C35, /* last */
+ /*
+ * Burst Read. (Offset 8 in UPM RAM)
+ */
+ 0x0E26FC04, 0x10ADFC04, 0xF0AFFC00, 0xF0AFFC00,
+ 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C45, /* last */
+ _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Single Write. (Offset 18 in UPM RAM)
+ */
+ 0x1F27FC04, 0xEEAEBC04, 0x01B93C00, 0x1FF77C45, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Burst Write. (Offset 20 in UPM RAM)
+ */
+ 0x0E26BC00, 0x10AD7C00, 0xF0AFFC00, 0xF0AFFC00,
+ 0xE1BBBC04, 0x1FF77C45, /* last */
+ _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Refresh (Offset 30 in UPM RAM)
+ */
+ 0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC84,
+ 0xFFFFFC05, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Exception. (Offset 3c in UPM RAM)
+ */
+ 0x7FFFFC07, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_,
+};
+
+/* ------------------------------------------------------------------------- */
+
+
+/*
+ * Check Board Identity:
+ *
+ */
+
+int checkboard (void)
+{
+#ifdef CONFIG_IVMS8
+ puts ("Board: IVMS8\n");
+#endif
+#ifdef CONFIG_IVML24
+ puts ("Board: IVM-L8/24\n");
+#endif
+ return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+phys_size_t initdram (int board_type)
+{
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+ volatile memctl8xx_t *memctl = &immr->im_memctl;
+ long int size_b0;
+
+ /* enable SDRAM clock ("switch on" SDRAM) */
+ immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_SDRAM_CLKE); /* GPIO */
+ immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_SDRAM_CLKE); /* active output */
+ immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_SDRAM_CLKE; /* output */
+ immr->im_cpm.cp_pbdat |= CONFIG_SYS_PB_SDRAM_CLKE; /* assert SDRAM CLKE */
+ udelay (1);
+
+ /*
+ * Map controller bank 1 for ELIC SACCO
+ */
+ memctl->memc_or1 = CONFIG_SYS_OR1;
+ memctl->memc_br1 = CONFIG_SYS_BR1;
+
+ /*
+ * Map controller bank 2 for ELIC EPIC
+ */
+ memctl->memc_or2 = CONFIG_SYS_OR2;
+ memctl->memc_br2 = CONFIG_SYS_BR2;
+
+ /*
+ * Configure UPMA for SHARC
+ */
+ upmconfig (UPMA, (uint *) sharc_table,
+ sizeof (sharc_table) / sizeof (uint));
+
+#if defined(CONFIG_IVML24)
+ /*
+ * Map controller bank 4 for HDLC Address space
+ */
+ memctl->memc_or4 = CONFIG_SYS_OR4;
+ memctl->memc_br4 = CONFIG_SYS_BR4;
+#endif
+
+ /*
+ * Map controller bank 5 for SHARC
+ */
+ memctl->memc_or5 = CONFIG_SYS_OR5;
+ memctl->memc_br5 = CONFIG_SYS_BR5;
+
+ memctl->memc_mamr = 0x00001000;
+
+ /*
+ * Configure UPMB for SDRAM
+ */
+ upmconfig (UPMB, (uint *) sdram_table,
+ sizeof (sdram_table) / sizeof (uint));
+
+ memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_8K;
+
+ memctl->memc_mar = 0x00000088;
+
+ /*
+ * Map controller bank 3 to the SDRAM bank at preliminary address.
+ */
+ memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
+ memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
+
+ memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL; /* refresh not enabled yet */
+
+ udelay (200);
+ memctl->memc_mcr = 0x80806105; /* precharge */
+ udelay (1);
+ memctl->memc_mcr = 0x80806106; /* load mode register */
+ udelay (1);
+ memctl->memc_mcr = 0x80806130; /* autorefresh */
+ udelay (1);
+ memctl->memc_mcr = 0x80806130; /* autorefresh */
+ udelay (1);
+ memctl->memc_mcr = 0x80806130; /* autorefresh */
+ udelay (1);
+ memctl->memc_mcr = 0x80806130; /* autorefresh */
+ udelay (1);
+ memctl->memc_mcr = 0x80806130; /* autorefresh */
+ udelay (1);
+ memctl->memc_mcr = 0x80806130; /* autorefresh */
+ udelay (1);
+ memctl->memc_mcr = 0x80806130; /* autorefresh */
+ udelay (1);
+ memctl->memc_mcr = 0x80806130; /* autorefresh */
+
+ memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
+
+ /*
+ * Check Bank 0 Memory Size for re-configuration
+ */
+ size_b0 =
+ dram_size (CONFIG_SYS_MBMR_8COL, (long *) SDRAM_BASE3_PRELIM,
+ SDRAM_MAX_SIZE);
+
+ memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
+
+ return (size_b0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+
+static long int dram_size (long int mamr_value, long int *base,
+ long int maxsize)
+{
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+ volatile memctl8xx_t *memctl = &immr->im_memctl;
+
+ memctl->memc_mbmr = mamr_value;
+
+ return (get_ram_size (base, maxsize));
+}
+
+/* ------------------------------------------------------------------------- */
+
+void reset_phy (void)
+{
+ immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+
+ /* De-assert Ethernet Powerdown */
+ immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_ETH_POWERDOWN); /* GPIO */
+ immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_ETH_POWERDOWN); /* active output */
+ immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_ETH_POWERDOWN; /* output */
+ immr->im_cpm.cp_pbdat &= ~(CONFIG_SYS_PB_ETH_POWERDOWN); /* Enable PHY power */
+ udelay (1000);
+
+ /*
+ * RESET is implemented by a positive pulse of at least 1 us
+ * at the reset pin.
+ *
+ * Configure RESET pins for NS DP83843 PHY, and RESET chip.
+ *
+ * Note: The RESET pin is high active, but there is an
+ * inverter on the SPD823TS board...
+ */
+ immr->im_ioport.iop_pcpar &= ~(CONFIG_SYS_PC_ETH_RESET);
+ immr->im_ioport.iop_pcdir |= CONFIG_SYS_PC_ETH_RESET;
+ /* assert RESET signal of PHY */
+ immr->im_ioport.iop_pcdat &= ~(CONFIG_SYS_PC_ETH_RESET);
+ udelay (10);
+ /* de-assert RESET signal of PHY */
+ immr->im_ioport.iop_pcdat |= CONFIG_SYS_PC_ETH_RESET;
+ udelay (10);
+}
+
+/* ------------------------------------------------------------------------- */
+
+void show_boot_progress (int status)
+{
+#if defined(CONFIG_STATUS_LED)
+# if defined(STATUS_LED_YELLOW)
+ status_led_set (STATUS_LED_YELLOW,
+ (status < 0) ? STATUS_LED_ON : STATUS_LED_OFF);
+# endif /* STATUS_LED_YELLOW */
+# if defined(STATUS_LED_BOOT)
+ if (status == BOOTSTAGE_ID_DECOMP_IMAGE)
+ status_led_set (STATUS_LED_BOOT, STATUS_LED_OFF);
+# endif /* STATUS_LED_BOOT */
+#endif /* CONFIG_STATUS_LED */
+}
+
+/* ------------------------------------------------------------------------- */
+
+void ide_set_reset (int on)
+{
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+ int i;
+
+ /*
+ * Configure PC for IDE Reset Pin
+ */
+ if (on) { /* assert RESET */
+ immr->im_ioport.iop_pcdat &= ~(CONFIG_SYS_PC_IDE_RESET);
+
+#ifdef CONFIG_SYS_PB_12V_ENABLE
+ /* 12V Enable output OFF */
+ immr->im_cpm.cp_pbdat &= ~(CONFIG_SYS_PB_12V_ENABLE);
+
+ immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_12V_ENABLE);
+ immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_12V_ENABLE);
+ immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_12V_ENABLE;
+
+ /* wait 500 ms for the voltage to stabilize */
+ for (i = 0; i < 500; ++i)
+ udelay(1000);
+#endif /* CONFIG_SYS_PB_12V_ENABLE */
+ } else { /* release RESET */
+#ifdef CONFIG_SYS_PB_12V_ENABLE
+ /* 12V Enable output ON */
+ immr->im_cpm.cp_pbdat |= CONFIG_SYS_PB_12V_ENABLE;
+#endif /* CONFIG_SYS_PB_12V_ENABLE */
+
+#ifdef CONFIG_SYS_PB_IDE_MOTOR
+ /* configure IDE Motor voltage monitor pin as input */
+ immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+ immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+ immr->im_cpm.cp_pbdir &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+
+/* wait up to 1 s for the motor voltage to stabilize */
+ for (i = 0; i < 1000; ++i) {
+ if ((immr->im_cpm.cp_pbdat
+ & CONFIG_SYS_PB_IDE_MOTOR) != 0)
+ break;
+ udelay(1000);
+ }
+
+ if (i == 1000) { /* Timeout */
+ printf("\nWarning: 5V for IDE Motor missing\n");
+#ifdef CONFIG_STATUS_LED
+#ifdef STATUS_LED_YELLOW
+ status_led_set(STATUS_LED_YELLOW, STATUS_LED_ON);
+#endif
+#ifdef STATUS_LED_GREEN
+ status_led_set(STATUS_LED_GREEN, STATUS_LED_OFF);
+#endif
+#endif /* CONFIG_STATUS_LED */
+ }
+#endif /* CONFIG_SYS_PB_IDE_MOTOR */
+
+ immr->im_ioport.iop_pcdat |= CONFIG_SYS_PC_IDE_RESET;
+ }
+
+ /* program port pin as GPIO output */
+ immr->im_ioport.iop_pcpar &= ~(CONFIG_SYS_PC_IDE_RESET);
+ immr->im_ioport.iop_pcso &= ~(CONFIG_SYS_PC_IDE_RESET);
+ immr->im_ioport.iop_pcdir |= CONFIG_SYS_PC_IDE_RESET;
+}
+
+/* ------------------------------------------------------------------------- */
Code Review / kvmfornfv.git / blobdiff