--- /dev/null
+/*
+ * Copyright 2010-2012 Freescale Semiconductor, Inc.
+ *
+ * Authors: Roy Zang <tie-fei.zang@freescale.com>
+ * Chunhe Lan <b25806@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/io.h>
+#include <asm/cache.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/fsl_portals.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <netdev.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+
+#include "bcsr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ fsl_lbc_t *lbc = LBC_BASE_ADDR;
+
+ /* Set ABSWP to implement conversion of addresses in the LBC */
+ setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR;
+
+ printf("Board: P1023 RDS\n");
+
+ clrbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG_CLR);
+ setbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG0);
+
+ return 0;
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect. */
+phys_size_t fixed_sdram(void)
+{
+#ifndef CONFIG_SYS_RAMBOOT
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
+
+ set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
+
+ out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
+ out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
+ out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS);
+ out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG);
+ out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+ out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2);
+ out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1);
+ out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2);
+ out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
+ out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL);
+ out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
+ out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
+ out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL);
+ out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
+ out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1);
+ out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2);
+ out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
+#endif
+ return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024ul;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+#endif
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_BCSR_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + BCSR region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash + bcsr */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_BCSR_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ setup_portals();
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+ return gd->bus_clk;
+}
+
+unsigned long get_board_ddr_clk(ulong dummy)
+{
+ return gd->mem_clk;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR;
+ ccsr_gur_t *gur = (ccsr_gur_t *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+ struct fsl_pq_mdio_info dtsec_mdio_info;
+
+ /*
+ * Need to set dTSEC 1 pin multiplexing to TSEC. The default setting
+ * is not correct.
+ */
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_TSEC1_1);
+
+ dtsec_mdio_info.regs =
+ (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fsl_pq_mdio_init(bis, &dtsec_mdio_info);
+
+ fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
+
+ fm_info_set_mdio(FM1_DTSEC1,
+ miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
+ fm_info_set_mdio(FM1_DTSEC2,
+ miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
+
+ /* Make SERDES connected to SGMII by cleaing bcsr19[7] */
+ if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_SGMII)
+ clrbits_8(&bcsr[19], BCSR19_SGMII_SEL_L);
+
+#ifdef CONFIG_FMAN_ENET
+ cpu_eth_init(bis);
+#endif
+
+ return pci_eth_init(bis);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+ /* By default NOR is on, and NAND is disabled */
+#ifdef CONFIG_NAND_U_BOOT
+ do_fixup_by_path_string(blob, "nor_flash", "status", "disabled");
+ do_fixup_by_path_string(blob, "nand_flash", "status", "okay");
+#endif
+#ifdef CONFIG_HAS_FSL_DR_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
+ fdt_fixup_fman_ethernet(blob);
+}
+#endif
Code Review / kvmfornfv.git / blobdiff