--- /dev/null
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ * (C) Copyright 2003,Motorola Inc.
+ * Xianghua Xiao, (X.Xiao@motorola.com)
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <fsl_ddr_sdram.h>
+#include <ioports.h>
+#include <spd_sdram.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_lbc.h>
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+
+void local_bus_init(void);
+
+
+/*
+ * I/O Port configuration table
+ *
+ * if conf is 1, then that port pin will be configured at boot time
+ * according to the five values podr/pdir/ppar/psor/pdat for that entry
+ */
+
+const iop_conf_t iop_conf_tab[4][32] = {
+
+ /* Port A configuration */
+ { /* conf ppar psor pdir podr pdat */
+ /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
+ /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
+ /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
+ /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
+ /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
+ /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
+ /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
+ /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
+ /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
+ /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
+ /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
+ /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
+ /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
+ /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
+ /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
+ /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
+ /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
+ /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
+ /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
+ /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
+ /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
+ /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
+ /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */
+ /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */
+ /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */
+ /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */
+ /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */
+ /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */
+ /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */
+ /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */
+ /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */
+ /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */
+ },
+
+ /* Port B configuration */
+ { /* conf ppar psor pdir podr pdat */
+ /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
+ /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
+ /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
+ /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
+ /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
+ /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
+ /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
+ /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
+ /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
+ /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
+ /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
+ /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
+ /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
+ /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
+ /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
+ /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
+ /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
+ /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
+ /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */
+ /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
+ /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
+ },
+
+ /* Port C */
+ { /* conf ppar psor pdir podr pdat */
+ /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */
+ /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */
+ /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
+ /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */
+ /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */
+ /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */
+ /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */
+ /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
+ /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
+ /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
+ /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
+ /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
+ /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
+ /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
+ /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */
+ /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
+ /* PC15 */ { 1, 1, 0, 0, 0, 0 }, /* PC15 */
+ /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
+ /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */
+ /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */
+ /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */
+ /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FETHMDC */
+ /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* FETHMDIO */
+ /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */
+ /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */
+ /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */
+ /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */
+ /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */
+ /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */
+ /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */
+ /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */
+ /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */
+ },
+
+ /* Port D */
+ { /* conf ppar psor pdir podr pdat */
+ /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
+ /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
+ /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */
+ /* PD28 */ { 0, 1, 0, 0, 0, 0 }, /* PD28 */
+ /* PD27 */ { 0, 1, 1, 1, 0, 0 }, /* PD27 */
+ /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */
+ /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */
+ /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */
+ /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */
+ /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */
+ /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */
+ /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */
+ /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */
+ /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */
+ /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
+ /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
+ /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */
+ /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */
+ /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
+ /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
+ /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
+ /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
+ /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
+ /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
+ /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */
+ /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */
+ /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */
+ /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */
+ /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
+ }
+};
+
+
+/*
+ * MPC8560ADS Board Status & Control Registers
+ */
+typedef struct bcsr_ {
+ volatile unsigned char bcsr0;
+ volatile unsigned char bcsr1;
+ volatile unsigned char bcsr2;
+ volatile unsigned char bcsr3;
+ volatile unsigned char bcsr4;
+ volatile unsigned char bcsr5;
+} bcsr_t;
+
+void reset_phy (void)
+{
+#if defined(CONFIG_ETHER_ON_FCC) /* avoid compile warnings for now */
+ volatile bcsr_t *bcsr = (bcsr_t *) CONFIG_SYS_BCSR;
+#endif
+ /* reset Giga bit Ethernet port if needed here */
+
+ /* reset the CPM FEC port */
+#if (CONFIG_ETHER_INDEX == 2)
+ bcsr->bcsr2 &= ~FETH2_RST;
+ udelay(2);
+ bcsr->bcsr2 |= FETH2_RST;
+ udelay(1000);
+#elif (CONFIG_ETHER_INDEX == 3)
+ bcsr->bcsr3 &= ~FETH3_RST;
+ udelay(2);
+ bcsr->bcsr3 |= FETH3_RST;
+ udelay(1000);
+#endif
+#if defined(CONFIG_MII) && defined(CONFIG_ETHER_ON_FCC)
+ /* reset PHY */
+ miiphy_reset("FCC1", 0x0);
+
+ /* change PHY address to 0x02 */
+ bb_miiphy_write(NULL, 0, MII_MIPSCR, 0xf028);
+
+ bb_miiphy_write(NULL, 0x02, MII_BMCR,
+ BMCR_ANENABLE | BMCR_ANRESTART);
+#endif /* CONFIG_MII */
+}
+
+
+int checkboard (void)
+{
+ puts("Board: ADS\n");
+
+#ifdef CONFIG_PCI
+ printf("PCI1: 32 bit, %d MHz (compiled)\n",
+ CONFIG_SYS_CLK_FREQ / 1000000);
+#else
+ printf("PCI1: disabled\n");
+#endif
+
+ /*
+ * Initialize local bus.
+ */
+ local_bus_init();
+
+ return 0;
+}
+
+/*
+ * Initialize Local Bus
+ */
+
+void
+local_bus_init(void)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
+
+ uint clkdiv;
+ uint lbc_hz;
+ sys_info_t sysinfo;
+
+ /*
+ * Errata LBC11.
+ * Fix Local Bus clock glitch when DLL is enabled.
+ *
+ * If localbus freq is < 66MHz, DLL bypass mode must be used.
+ * If localbus freq is > 133MHz, DLL can be safely enabled.
+ * Between 66 and 133, the DLL is enabled with an override workaround.
+ */
+
+ get_sys_info(&sysinfo);
+ clkdiv = lbc->lcrr & LCRR_CLKDIV;
+ lbc_hz = sysinfo.freq_systembus / 1000000 / clkdiv;
+
+ if (lbc_hz < 66) {
+ lbc->lcrr = CONFIG_SYS_LBC_LCRR | LCRR_DBYP; /* DLL Bypass */
+
+ } else if (lbc_hz >= 133) {
+ lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP); /* DLL Enabled */
+
+ } else {
+ /*
+ * On REV1 boards, need to change CLKDIV before enable DLL.
+ * Default CLKDIV is 8, change it to 4 temporarily.
+ */
+ uint pvr = get_pvr();
+ uint temp_lbcdll = 0;
+
+ if (pvr == PVR_85xx_REV1) {
+ /* FIXME: Justify the high bit here. */
+ lbc->lcrr = 0x10000004;
+ }
+
+ lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP);/* DLL Enabled */
+ udelay(200);
+
+ /*
+ * Sample LBC DLL ctrl reg, upshift it to set the
+ * override bits.
+ */
+ temp_lbcdll = gur->lbcdllcr;
+ gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
+ asm("sync;isync;msync");
+ }
+}
+
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+void lbc_sdram_init(void)
+{
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
+ uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
+
+ puts("LBC SDRAM: ");
+ print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
+ "\n ");
+
+ /*
+ * Setup SDRAM Base and Option Registers
+ */
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
+ lbc->lbcr = CONFIG_SYS_LBC_LBCR;
+ asm("msync");
+
+ lbc->lsrt = CONFIG_SYS_LBC_LSRT;
+ lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
+ asm("sync");
+
+ /*
+ * Configure the SDRAM controller.
+ */
+ lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_1;
+ asm("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+
+ lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_2;
+ asm("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+
+ lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_3;
+ asm("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+
+ lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_4;
+ asm("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+
+ lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_5;
+ asm("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+}
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*************************************************************************
+ * fixed sdram init -- doesn't use serial presence detect.
+ ************************************************************************/
+phys_size_t fixed_sdram(void)
+{
+ #ifndef CONFIG_SYS_RAMBOOT
+ volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_FSL_DDR_ADDR);
+
+ ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
+ ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
+ ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
+ ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
+ ddr->sdram_mode = CONFIG_SYS_DDR_MODE;
+ ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
+ #if defined (CONFIG_DDR_ECC)
+ ddr->err_disable = 0x0000000D;
+ ddr->err_sbe = 0x00ff0000;
+ #endif
+ asm("sync;isync;msync");
+ udelay(500);
+ #if defined (CONFIG_DDR_ECC)
+ /* Enable ECC checking */
+ ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
+ #else
+ ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
+ #endif
+ asm("sync; isync; msync");
+ udelay(500);
+ #endif
+ return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+}
+#endif /* !defined(CONFIG_SPD_EEPROM) */
+
+
+#if defined(CONFIG_PCI)
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc85xxads_config_table[] = {
+ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+ PCI_IDSEL_NUMBER, PCI_ANY_ID,
+ pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+ PCI_ENET0_MEMADDR,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+ } },
+ { }
+};
+#endif
+
+
+static struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+ config_table: pci_mpc85xxads_config_table,
+#endif
+};
+
+#endif /* CONFIG_PCI */
+
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+ pci_mpc85xx_init(&hose);
+#endif /* CONFIG_PCI */
+}
+
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup(void *blob, bd_t *bd)
+{
+ int node, tmp[2];
+ const char *path;
+
+ ft_cpu_setup(blob, bd);
+
+ node = fdt_path_offset(blob, "/aliases");
+ tmp[0] = 0;
+ if (node >= 0) {
+#ifdef CONFIG_PCI
+ path = fdt_getprop(blob, node, "pci0", NULL);
+ if (path) {
+ tmp[1] = hose.last_busno - hose.first_busno;
+ do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+ }
+#endif
+ }
+}
+#endif
Code Review / kvmfornfv.git / blobdiff