--- /dev/null
+/*
+ * Copyright 2004, 2011 Freescale Semiconductor.
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <fsl_ddr_sdram.h>
+#include <ioports.h>
+#include <spd_sdram.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+
+#include "../common/cadmus.h"
+#include "../common/eeprom.h"
+#include "../common/via.h"
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+void local_bus_init(void);
+
+/*
+ * I/O Port configuration table
+ *
+ * if conf is 1, then that port pin will be configured at boot time
+ * according to the five values podr/pdir/ppar/psor/pdat for that entry
+ */
+
+const iop_conf_t iop_conf_tab[4][32] = {
+
+ /* Port A configuration */
+ { /* conf ppar psor pdir podr pdat */
+ /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
+ /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
+ /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
+ /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
+ /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
+ /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
+ /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
+ /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
+ /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
+ /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
+ /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
+ /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
+ /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
+ /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
+ /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
+ /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
+ /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
+ /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
+ /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
+ /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
+ /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
+ /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
+ /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */
+ /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */
+ /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */
+ /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */
+ /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */
+ /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */
+ /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */
+ /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */
+ /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */
+ /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */
+ },
+
+ /* Port B configuration */
+ { /* conf ppar psor pdir podr pdat */
+ /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
+ /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
+ /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
+ /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
+ /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
+ /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
+ /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
+ /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
+ /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
+ /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
+ /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
+ /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
+ /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
+ /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
+ /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
+ /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
+ /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
+ /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
+ /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */
+ /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
+ /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
+ },
+
+ /* Port C */
+ { /* conf ppar psor pdir podr pdat */
+ /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */
+ /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */
+ /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
+ /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */
+ /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */
+ /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */
+ /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */
+ /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
+ /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
+ /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
+ /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
+ /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
+ /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
+ /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
+ /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */
+ /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
+ /* PC15 */ { 1, 1, 0, 0, 0, 0 }, /* PC15 */
+ /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
+ /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */
+ /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */
+ /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */
+ /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FETHMDC */
+ /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* FETHMDIO */
+ /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */
+ /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */
+ /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */
+ /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */
+ /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */
+ /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */
+ /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */
+ /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */
+ /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */
+ },
+
+ /* Port D */
+ { /* conf ppar psor pdir podr pdat */
+ /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
+ /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
+ /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */
+ /* PD28 */ { 0, 1, 0, 0, 0, 0 }, /* PD28 */
+ /* PD27 */ { 0, 1, 1, 1, 0, 0 }, /* PD27 */
+ /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */
+ /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */
+ /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */
+ /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */
+ /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */
+ /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */
+ /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */
+ /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */
+ /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */
+ /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
+ /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
+ /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */
+ /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */
+ /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
+ /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
+ /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
+ /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
+ /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
+ /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
+ /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */
+ /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */
+ /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */
+ /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */
+ /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
+ }
+};
+
+int checkboard (void)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ char buf[32];
+
+ /* PCI slot in USER bits CSR[6:7] by convention. */
+ uint pci_slot = get_pci_slot ();
+
+ uint pci_dual = get_pci_dual (); /* PCI DUAL in CM_PCI[3] */
+ uint pci1_32 = gur->pordevsr & 0x10000; /* PORDEVSR[15] */
+ uint pci1_clk_sel = gur->porpllsr & 0x8000; /* PORPLLSR[16] */
+ uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */
+
+ uint pci1_speed = get_clock_freq (); /* PCI PSPEED in [4:5] */
+
+ uint cpu_board_rev = get_cpu_board_revision ();
+
+ printf ("Board: CDS Version 0x%02x, PCI Slot %d\n",
+ get_board_version (), pci_slot);
+
+ printf ("CPU Board Revision %d.%d (0x%04x)\n",
+ MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev),
+ MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev);
+
+ printf("PCI1: %d bit, %s MHz, %s\n",
+ (pci1_32) ? 32 : 64,
+ strmhz(buf, pci1_speed),
+ pci1_clk_sel ? "sync" : "async");
+
+ if (pci_dual) {
+ printf("PCI2: 32 bit, 66 MHz, %s\n",
+ pci2_clk_sel ? "sync" : "async");
+ } else {
+ printf("PCI2: disabled\n");
+ }
+
+ /*
+ * Initialize local bus.
+ */
+ local_bus_init ();
+
+ return 0;
+}
+
+/*
+ * Initialize Local Bus
+ */
+void
+local_bus_init(void)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
+
+ uint clkdiv;
+ uint lbc_hz;
+ sys_info_t sysinfo;
+ uint temp_lbcdll;
+
+ /*
+ * Errata LBC11.
+ * Fix Local Bus clock glitch when DLL is enabled.
+ *
+ * If localbus freq is < 66MHz, DLL bypass mode must be used.
+ * If localbus freq is > 133MHz, DLL can be safely enabled.
+ * Between 66 and 133, the DLL is enabled with an override workaround.
+ */
+
+ get_sys_info(&sysinfo);
+ clkdiv = lbc->lcrr & LCRR_CLKDIV;
+ lbc_hz = sysinfo.freq_systembus / 1000000 / clkdiv;
+
+ if (lbc_hz < 66) {
+ lbc->lcrr |= LCRR_DBYP; /* DLL Bypass */
+
+ } else if (lbc_hz >= 133) {
+ lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */
+
+ } else {
+ lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */
+ udelay(200);
+
+ /*
+ * Sample LBC DLL ctrl reg, upshift it to set the
+ * override bits.
+ */
+ temp_lbcdll = gur->lbcdllcr;
+ gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
+ asm("sync;isync;msync");
+ }
+}
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+void lbc_sdram_init(void)
+{
+#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
+
+ uint idx;
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
+ uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
+ uint cpu_board_rev;
+ uint lsdmr_common;
+
+ puts("LBC SDRAM: ");
+ print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
+ "\n ");
+
+ /*
+ * Setup SDRAM Base and Option Registers
+ */
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
+ lbc->lbcr = CONFIG_SYS_LBC_LBCR;
+ asm("msync");
+
+ lbc->lsrt = CONFIG_SYS_LBC_LSRT;
+ lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
+ asm("msync");
+
+ /*
+ * Determine which address lines to use baed on CPU board rev.
+ */
+ cpu_board_rev = get_cpu_board_revision();
+ lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON;
+ if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
+ lsdmr_common |= LSDMR_BSMA1617;
+ } else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
+ lsdmr_common |= LSDMR_BSMA1516;
+ } else {
+ /*
+ * Assume something unable to identify itself is
+ * really old, and likely has lines 16/17 mapped.
+ */
+ lsdmr_common |= LSDMR_BSMA1617;
+ }
+
+ /*
+ * Issue PRECHARGE ALL command.
+ */
+ lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
+ asm("sync;msync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+
+ /*
+ * Issue 8 AUTO REFRESH commands.
+ */
+ for (idx = 0; idx < 8; idx++) {
+ lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
+ asm("sync;msync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+ }
+
+ /*
+ * Issue 8 MODE-set command.
+ */
+ lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
+ asm("sync;msync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+
+ /*
+ * Issue NORMAL OP command.
+ */
+ lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
+ asm("sync;msync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(200); /* Overkill. Must wait > 200 bus cycles */
+
+#endif /* enable SDRAM init */
+}
+
+#if defined(CONFIG_PCI)
+/* For some reason the Tundra PCI bridge shows up on itself as a
+ * different device. Work around that by refusing to configure it.
+ */
+void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_table *tab) { }
+
+static struct pci_config_table pci_mpc85xxcds_config_table[] = {
+ {0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
+ {0x1106, 0x0686, PCI_ANY_ID, 1, VIA_ID, 0, mpc85xx_config_via, {0,0,0}},
+ {0x1106, 0x0571, PCI_ANY_ID, 1, VIA_ID, 1,
+ mpc85xx_config_via_usbide, {0,0,0}},
+ {0x1105, 0x3038, PCI_ANY_ID, 1, VIA_ID, 2,
+ mpc85xx_config_via_usb, {0,0,0}},
+ {0x1106, 0x3038, PCI_ANY_ID, 1, VIA_ID, 3,
+ mpc85xx_config_via_usb2, {0,0,0}},
+ {0x1106, 0x3058, PCI_ANY_ID, 1, VIA_ID, 5,
+ mpc85xx_config_via_power, {0,0,0}},
+ {0x1106, 0x3068, PCI_ANY_ID, 1, VIA_ID, 6,
+ mpc85xx_config_via_ac97, {0,0,0}},
+ {},
+};
+
+static struct pci_controller hose[] = {
+ { config_table: pci_mpc85xxcds_config_table,},
+#ifdef CONFIG_MPC85XX_PCI2
+ {},
+#endif
+};
+
+#endif /* CONFIG_PCI */
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+ pci_mpc85xx_init(hose);
+#endif
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_pci_setup(void *blob, bd_t *bd)
+{
+ int node, tmp[2];
+ const char *path;
+
+ node = fdt_path_offset(blob, "/aliases");
+ tmp[0] = 0;
+ if (node >= 0) {
+#ifdef CONFIG_PCI1
+ path = fdt_getprop(blob, node, "pci0", NULL);
+ if (path) {
+ tmp[1] = hose[0].last_busno - hose[0].first_busno;
+ do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+ }
+#endif
+#ifdef CONFIG_MPC85XX_PCI2
+ path = fdt_getprop(blob, node, "pci1", NULL);
+ if (path) {
+ tmp[1] = hose[1].last_busno - hose[1].first_busno;
+ do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+ }
+#endif
+ }
+}
+#endif
Code Review / kvmfornfv.git / blobdiff