--- /dev/null
+/*
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ * Author: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * This file handles the board muxing between the Fman Ethernet MACs and
+ * the RGMII/SGMII/XGMII PHYs on a Freescale P5040 "Super Hydra" reference
+ * board. The RGMII PHYs are the two on-board 1Gb ports. The SGMII PHYs are
+ * provided by the standard Freescale four-port SGMII riser card. The 10Gb
+ * XGMII PHYs are provided via the XAUI riser card. The P5040 has 2 FMans
+ * and 5 1G interfaces and 10G interface per FMan. Based on the options in
+ * the RCW, we could have upto 3 SGMII cards and 1 XAUI card at a time.
+ *
+ * Muxing is handled via the PIXIS BRDCFG1 register. The EMI1 bits control
+ * muxing among the RGMII PHYs and the SGMII PHYs. The value for RGMII is
+ * always the same (0). The value for SGMII depends on which slot the riser is
+ * inserted in. The EMI2 bits control muxing for the the XGMII. Like SGMII,
+ * the value is based on which slot the XAUI is inserted in.
+ *
+ * The SERDES configuration is used to determine where the SGMII and XAUI cards
+ * exist, and also which Fman's MACs are routed to which PHYs. So for a given
+ * Fman MAC, there is one and only PHY it connects to. MACs cannot be routed
+ * to PHYs dynamically.
+ *
+ *
+ * This file also updates the device tree in three ways:
+ *
+ * 1) The status of each virtual MDIO node that is referenced by an Ethernet
+ * node is set to "okay".
+ *
+ * 2) The phy-handle property of each active Ethernet MAC node is set to the
+ * appropriate PHY node.
+ *
+ * 3) The "mux value" for each virtual MDIO node is set to the correct value,
+ * if necessary. Some virtual MDIO nodes do not have configurable mux
+ * values, so those values are hard-coded in the DTS. On the HYDRA board,
+ * the virtual MDIO node for the SGMII card needs to be updated.
+ *
+ * For all this to work, the device tree needs to have the following:
+ *
+ * 1) An alias for each PHY node that an Ethernet node could be routed to.
+ *
+ * 2) An alias for each real and virtual MDIO node that is disabled by default
+ * and might need to be enabled, and also might need to have its mux-value
+ * updated.
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/fsl_serdes.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+#include <fdt_support.h>
+#include <asm/fsl_dtsec.h>
+
+#include "../common/ngpixis.h"
+#include "../common/fman.h"
+
+#ifdef CONFIG_FMAN_ENET
+
+#define BRDCFG1_EMI1_SEL_MASK 0x70
+#define BRDCFG1_EMI1_SEL_SLOT1 0x10
+#define BRDCFG1_EMI1_SEL_SLOT2 0x20
+#define BRDCFG1_EMI1_SEL_SLOT5 0x30
+#define BRDCFG1_EMI1_SEL_SLOT6 0x40
+#define BRDCFG1_EMI1_SEL_SLOT7 0x50
+#define BRDCFG1_EMI1_SEL_SLOT3 0x60
+#define BRDCFG1_EMI1_SEL_RGMII 0x00
+#define BRDCFG1_EMI1_EN 0x08
+#define BRDCFG1_EMI2_SEL_MASK 0x06
+#define BRDCFG1_EMI2_SEL_SLOT1 0x00
+#define BRDCFG1_EMI2_SEL_SLOT2 0x02
+
+#define BRDCFG2_REG_GPIO_SEL 0x20
+
+/* SGMII */
+#define PHY_BASE_ADDR 0x00
+#define REGNUM 0x00
+#define PORT_NUM_FM1 0x04
+#define PORT_NUM_FM2 0x02
+
+/*
+ * BRDCFG1 mask and value for each MAC
+ *
+ * This array contains the BRDCFG1 values (in mask/val format) that route the
+ * MDIO bus to a particular RGMII or SGMII PHY.
+ */
+static struct {
+ u8 mask;
+ u8 val;
+} mdio_mux[NUM_FM_PORTS];
+
+/*
+ * Mapping of all 18 SERDES lanes to board slots. A value of '0' here means
+ * that the mapping must be determined dynamically, or that the lane maps to
+ * something other than a board slot
+ */
+static u8 lane_to_slot[] = {
+ 7, 7, 0, 0, 0, 0, 0, 0, 0, 0, 2, 2, 2, 2, 1, 1, 0, 0, 0, 0
+};
+
+/*
+ * Set the board muxing for a given MAC
+ *
+ * The MDIO layer calls this function every time it wants to talk to a PHY.
+ */
+void super_hydra_mux_mdio(u8 mask, u8 val)
+{
+ clrsetbits_8(&pixis->brdcfg1, mask, val);
+}
+
+struct super_hydra_mdio {
+ u8 mask;
+ u8 val;
+ struct mii_dev *realbus;
+};
+
+static int super_hydra_mdio_read(struct mii_dev *bus, int addr, int devad,
+ int regnum)
+{
+ struct super_hydra_mdio *priv = bus->priv;
+
+ super_hydra_mux_mdio(priv->mask, priv->val);
+
+ return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int super_hydra_mdio_write(struct mii_dev *bus, int addr, int devad,
+ int regnum, u16 value)
+{
+ struct super_hydra_mdio *priv = bus->priv;
+
+ super_hydra_mux_mdio(priv->mask, priv->val);
+
+ return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int super_hydra_mdio_reset(struct mii_dev *bus)
+{
+ struct super_hydra_mdio *priv = bus->priv;
+
+ return priv->realbus->reset(priv->realbus);
+}
+
+static void super_hydra_mdio_set_mux(char *name, u8 mask, u8 val)
+{
+ struct mii_dev *bus = miiphy_get_dev_by_name(name);
+ struct super_hydra_mdio *priv = bus->priv;
+
+ priv->mask = mask;
+ priv->val = val;
+}
+
+static int super_hydra_mdio_init(char *realbusname, char *fakebusname)
+{
+ struct super_hydra_mdio *hmdio;
+ struct mii_dev *bus = mdio_alloc();
+
+ if (!bus) {
+ printf("Failed to allocate Hydra MDIO bus\n");
+ return -1;
+ }
+
+ hmdio = malloc(sizeof(*hmdio));
+ if (!hmdio) {
+ printf("Failed to allocate Hydra private data\n");
+ free(bus);
+ return -1;
+ }
+
+ bus->read = super_hydra_mdio_read;
+ bus->write = super_hydra_mdio_write;
+ bus->reset = super_hydra_mdio_reset;
+ sprintf(bus->name, fakebusname);
+
+ hmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+ if (!hmdio->realbus) {
+ printf("No bus with name %s\n", realbusname);
+ free(bus);
+ free(hmdio);
+ return -1;
+ }
+
+ bus->priv = hmdio;
+
+ return mdio_register(bus);
+}
+
+/*
+ * Given the following ...
+ *
+ * 1) A pointer to an Fman Ethernet node (as identified by the 'compat'
+ * compatible string and 'addr' physical address)
+ *
+ * 2) An Fman port
+ *
+ * ... update the phy-handle property of the Ethernet node to point to the
+ * right PHY. This assumes that we already know the PHY for each port. That
+ * information is stored in mdio_mux[].
+ *
+ * The offset of the Fman Ethernet node is also passed in for convenience, but
+ * it is not used.
+ *
+ * Note that what we call "Fman ports" (enum fm_port) is really an Fman MAC.
+ * Inside the Fman, "ports" are things that connect to MACs. We only call them
+ * ports in U-Boot because on previous Ethernet devices (e.g. Gianfar), MACs
+ * and ports are the same thing.
+ */
+void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
+ enum fm_port port, int offset)
+{
+ enum srds_prtcl device;
+ int lane, slot, phy;
+ char alias[32];
+
+ /* RGMII and XGMII are already mapped correctly in the DTS */
+
+ if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
+ device = serdes_device_from_fm_port(port);
+ lane = serdes_get_first_lane(device);
+ slot = lane_to_slot[lane];
+ phy = fm_info_get_phy_address(port);
+
+ sprintf(alias, "phy_sgmii_slot%u_%x", slot, phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ }
+}
+
+#define PIXIS_SW2_LANE_23_SEL 0x80
+#define PIXIS_SW2_LANE_45_SEL 0x40
+#define PIXIS_SW2_LANE_67_SEL_MASK 0x30
+#define PIXIS_SW2_LANE_67_SEL_5 0x00
+#define PIXIS_SW2_LANE_67_SEL_6 0x20
+#define PIXIS_SW2_LANE_67_SEL_7 0x10
+#define PIXIS_SW2_LANE_8_SEL 0x08
+#define PIXIS_SW2_LANE_1617_SEL 0x04
+#define PIXIS_SW11_LANE_9_SEL 0x04
+/*
+ * Initialize the lane_to_slot[] array.
+ *
+ * On the P4080DS "Expedition" board, the mapping of SERDES lanes to board
+ * slots is hard-coded. On the Hydra board, however, the mapping is controlled
+ * by board switch SW2, so the lane_to_slot[] array needs to be dynamically
+ * initialized.
+ */
+static void initialize_lane_to_slot(void)
+{
+ u8 sw2 = in_8(&PIXIS_SW(2));
+ /* SW11 appears in the programming model as SW9 */
+ u8 sw11 = in_8(&PIXIS_SW(9));
+
+ lane_to_slot[2] = (sw2 & PIXIS_SW2_LANE_23_SEL) ? 7 : 4;
+ lane_to_slot[3] = lane_to_slot[2];
+
+ lane_to_slot[4] = (sw2 & PIXIS_SW2_LANE_45_SEL) ? 7 : 6;
+ lane_to_slot[5] = lane_to_slot[4];
+
+ switch (sw2 & PIXIS_SW2_LANE_67_SEL_MASK) {
+ case PIXIS_SW2_LANE_67_SEL_5:
+ lane_to_slot[6] = 5;
+ break;
+ case PIXIS_SW2_LANE_67_SEL_6:
+ lane_to_slot[6] = 6;
+ break;
+ case PIXIS_SW2_LANE_67_SEL_7:
+ lane_to_slot[6] = 7;
+ break;
+ }
+ lane_to_slot[7] = lane_to_slot[6];
+
+ lane_to_slot[8] = (sw2 & PIXIS_SW2_LANE_8_SEL) ? 3 : 0;
+ lane_to_slot[9] = (sw11 & PIXIS_SW11_LANE_9_SEL) ? 0 : 3;
+
+ lane_to_slot[16] = (sw2 & PIXIS_SW2_LANE_1617_SEL) ? 1 : 0;
+ lane_to_slot[17] = lane_to_slot[16];
+}
+
+#endif /* #ifdef CONFIG_FMAN_ENET */
+
+/*
+ * Configure the status for the virtual MDIO nodes
+ *
+ * Rather than create the virtual MDIO nodes from scratch for each active
+ * virtual MDIO, we expect the DTS to have the nodes defined already, and we
+ * only enable the ones that are actually active.
+ *
+ * We assume that the DTS already hard-codes the status for all the
+ * virtual MDIO nodes to "disabled", so all we need to do is enable the
+ * active ones.
+ */
+void fdt_fixup_board_enet(void *fdt)
+{
+#ifdef CONFIG_FMAN_ENET
+ enum fm_port i;
+ int lane, slot;
+
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ int idx = i - FM1_DTSEC1;
+
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_SGMII:
+ lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx);
+ if (lane >= 0) {
+ char alias[32];
+
+ slot = lane_to_slot[lane];
+ sprintf(alias, "hydra_sg_slot%u", slot);
+ fdt_status_okay_by_alias(fdt, alias);
+ debug("Enabled MDIO node %s (slot %i)\n",
+ alias, slot);
+ }
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ fdt_status_okay_by_alias(fdt, "hydra_rg");
+ debug("Enabled MDIO node hydra_rg\n");
+ break;
+ default:
+ break;
+ }
+ }
+
+ lane = serdes_get_first_lane(XAUI_FM1);
+ if (lane >= 0) {
+ char alias[32];
+
+ slot = lane_to_slot[lane];
+ sprintf(alias, "hydra_xg_slot%u", slot);
+ fdt_status_okay_by_alias(fdt, alias);
+ debug("Enabled MDIO node %s (slot %i)\n", alias, slot);
+ }
+
+#if CONFIG_SYS_NUM_FMAN == 2
+ for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
+ int idx = i - FM2_DTSEC1;
+
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_SGMII:
+ lane = serdes_get_first_lane(SGMII_FM2_DTSEC1 + idx);
+ if (lane >= 0) {
+ char alias[32];
+
+ slot = lane_to_slot[lane];
+ sprintf(alias, "hydra_sg_slot%u", slot);
+ fdt_status_okay_by_alias(fdt, alias);
+ debug("Enabled MDIO node %s (slot %i)\n",
+ alias, slot);
+ }
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ fdt_status_okay_by_alias(fdt, "hydra_rg");
+ debug("Enabled MDIO node hydra_rg\n");
+ break;
+ default:
+ break;
+ }
+ }
+
+ lane = serdes_get_first_lane(XAUI_FM2);
+ if (lane >= 0) {
+ char alias[32];
+
+ slot = lane_to_slot[lane];
+ sprintf(alias, "hydra_xg_slot%u", slot);
+ fdt_status_okay_by_alias(fdt, alias);
+ debug("Enabled MDIO node %s (slot %i)\n", alias, slot);
+ }
+#endif /* CONFIG_SYS_NUM_FMAN == 2 */
+#endif /* CONFIG_FMAN_ENET */
+}
+
+/*
+ * Mapping of SerDes Protocol to MDIO MUX value and PHY address.
+ *
+ * Fman 1:
+ * DTSEC1 | DTSEC2 | DTSEC3 | DTSEC4
+ * Mux Phy | Mux Phy | Mux Phy | Mux Phy
+ * Value Addr | Value Addr | Value Addr | Value Addr
+ * 0x00 2 1c | 2 1d | 2 1e | 2 1f
+ * 0x01 | | 6 1c |
+ * 0x02 | | 3 1c | 3 1d
+ * 0x03 2 1c | 2 1d | 2 1e | 2 1f
+ * 0x04 2 1c | 2 1d | 2 1e | 2 1f
+ * 0x05 | | 3 1c | 3 1d
+ * 0x06 2 1c | 2 1d | 2 1e | 2 1f
+ * 0x07 | | 6 1c |
+ * 0x11 2 1c | 2 1d | 2 1e | 2 1f
+ * 0x2a 2 | | 2 1e | 2 1f
+ * 0x34 6 1c | 6 1d | 4 1e | 4 1f
+ * 0x35 | | 3 1c | 3 1d
+ * 0x36 6 1c | 6 1d | 4 1e | 4 1f
+ * | | |
+ * Fman 2: | | |
+ * DTSEC1 | DTSEC2 | DTSEC3 | DTSEC4
+ * EMI1 | EMI1 | EMI1 | EMI1
+ * Mux Phy | Mux Phy | Mux Phy | Mux Phy
+ * Value Addr | Value Addr | Value Addr | Value Addr
+ * 0x00 | | 6 1c | 6 1d
+ * 0x01 | | |
+ * 0x02 | | 6 1c | 6 1d
+ * 0x03 3 1c | 3 1d | 6 1c | 6 1d
+ * 0x04 3 1c | 3 1d | 6 1c | 6 1d
+ * 0x05 | | 6 1c | 6 1d
+ * 0x06 | | 6 1c | 6 1d
+ * 0x07 | | |
+ * 0x11 | | |
+ * 0x2a | | |
+ * 0x34 | | |
+ * 0x35 | | |
+ * 0x36 | | |
+ */
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_FMAN_ENET
+ struct fsl_pq_mdio_info dtsec_mdio_info;
+ struct tgec_mdio_info tgec_mdio_info;
+ unsigned int i, slot;
+ int lane;
+ struct mii_dev *bus;
+ int qsgmii;
+ int phy_real_addr;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ int srds_prtcl = (in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26;
+
+ printf("Initializing Fman\n");
+
+ initialize_lane_to_slot();
+
+ /* We want to use the PIXIS to configure MUX routing, not GPIOs. */
+ setbits_8(&pixis->brdcfg2, BRDCFG2_REG_GPIO_SEL);
+
+ memset(mdio_mux, 0, sizeof(mdio_mux));
+
+ dtsec_mdio_info.regs =
+ (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the real 1G MDIO bus */
+ fsl_pq_mdio_init(bis, &dtsec_mdio_info);
+
+ tgec_mdio_info.regs =
+ (struct tgec_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+ tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+ /* Register the real 10G MDIO bus */
+ fm_tgec_mdio_init(bis, &tgec_mdio_info);
+
+ /* Register the three virtual MDIO front-ends */
+ super_hydra_mdio_init(DEFAULT_FM_MDIO_NAME,
+ "SUPER_HYDRA_RGMII_MDIO");
+ super_hydra_mdio_init(DEFAULT_FM_MDIO_NAME,
+ "SUPER_HYDRA_FM1_SGMII_MDIO");
+ super_hydra_mdio_init(DEFAULT_FM_MDIO_NAME,
+ "SUPER_HYDRA_FM2_SGMII_MDIO");
+ super_hydra_mdio_init(DEFAULT_FM_MDIO_NAME,
+ "SUPER_HYDRA_FM3_SGMII_MDIO");
+ super_hydra_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME,
+ "SUPER_HYDRA_FM1_TGEC_MDIO");
+ super_hydra_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME,
+ "SUPER_HYDRA_FM2_TGEC_MDIO");
+
+ /*
+ * Program the DTSEC PHY addresses assuming that they are all SGMII.
+ * For any DTSEC that's RGMII, we'll override its PHY address later.
+ * We assume that DTSEC5 is only used for RGMII.
+ */
+ fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_10GEC1, CONFIG_SYS_FM2_10GEC1_PHY_ADDR);
+
+#if (CONFIG_SYS_NUM_FMAN == 2)
+ fm_info_set_phy_address(FM2_DTSEC1, CONFIG_SYS_FM2_DTSEC1_PHY_ADDR);
+ fm_info_set_phy_address(FM2_DTSEC2, CONFIG_SYS_FM2_DTSEC2_PHY_ADDR);
+ fm_info_set_phy_address(FM2_DTSEC3, CONFIG_SYS_FM2_DTSEC1_PHY_ADDR);
+ fm_info_set_phy_address(FM2_DTSEC4, CONFIG_SYS_FM2_DTSEC2_PHY_ADDR);
+ fm_info_set_phy_address(FM2_10GEC1, CONFIG_SYS_FM1_10GEC1_PHY_ADDR);
+#endif
+
+ switch (srds_prtcl) {
+ case 0:
+ case 3:
+ case 4:
+ case 6:
+ case 0x11:
+ case 0x2a:
+ case 0x34:
+ case 0x36:
+ fm_info_set_phy_address(FM1_DTSEC3,
+ CONFIG_SYS_FM1_DTSEC3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC4,
+ CONFIG_SYS_FM1_DTSEC4_PHY_ADDR);
+ break;
+ case 1:
+ case 2:
+ case 5:
+ case 7:
+ case 0x35:
+ fm_info_set_phy_address(FM1_DTSEC3,
+ CONFIG_SYS_FM1_DTSEC1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC4,
+ CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
+ break;
+ default:
+ printf("Fman: Unsupport SerDes Protocol 0x%02x\n", srds_prtcl);
+ break;
+ }
+
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ int idx = i - FM1_DTSEC1;
+
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_SGMII:
+ lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx);
+ if (lane < 0)
+ break;
+ slot = lane_to_slot[lane];
+ mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK;
+ debug("FM1@DTSEC%u expects SGMII in slot %u\n",
+ idx + 1, slot);
+ switch (slot) {
+ case 1:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT1 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 2:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT2 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 3:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT3 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 5:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT5 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 6:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT6 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 7:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT7 |
+ BRDCFG1_EMI1_EN;
+ break;
+ };
+
+ super_hydra_mdio_set_mux("SUPER_HYDRA_FM1_SGMII_MDIO",
+ mdio_mux[i].mask, mdio_mux[i].val);
+ fm_info_set_mdio(i,
+ miiphy_get_dev_by_name("SUPER_HYDRA_FM1_SGMII_MDIO"));
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ /*
+ * FM1 DTSEC5 is routed via EC1 to the first on-board
+ * RGMII port. FM2 DTSEC5 is routed via EC2 to the
+ * second on-board RGMII port. The other DTSECs cannot
+ * be routed to RGMII.
+ */
+ debug("FM1@DTSEC%u is RGMII at address %u\n",
+ idx + 1, 0);
+ fm_info_set_phy_address(i, 0);
+ mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK;
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_RGMII |
+ BRDCFG1_EMI1_EN;
+ super_hydra_mdio_set_mux("SUPER_HYDRA_RGMII_MDIO",
+ mdio_mux[i].mask, mdio_mux[i].val);
+ fm_info_set_mdio(i,
+ miiphy_get_dev_by_name("SUPER_HYDRA_RGMII_MDIO"));
+ break;
+ case PHY_INTERFACE_MODE_NONE:
+ fm_info_set_phy_address(i, 0);
+ break;
+ default:
+ printf("Fman1: DTSEC%u set to unknown interface %i\n",
+ idx + 1, fm_info_get_enet_if(i));
+ fm_info_set_phy_address(i, 0);
+ break;
+ }
+ }
+
+ bus = miiphy_get_dev_by_name("SUPER_HYDRA_FM1_SGMII_MDIO");
+ qsgmii = is_qsgmii_riser_card(bus, PHY_BASE_ADDR, PORT_NUM_FM1, REGNUM);
+
+ if (qsgmii) {
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + PORT_NUM_FM1; i++) {
+ if (fm_info_get_enet_if(i) ==
+ PHY_INTERFACE_MODE_SGMII) {
+ phy_real_addr = PHY_BASE_ADDR + i - FM1_DTSEC1;
+ fm_info_set_phy_address(i, phy_real_addr);
+ }
+ }
+ switch (srds_prtcl) {
+ case 0x00:
+ case 0x03:
+ case 0x04:
+ case 0x06:
+ case 0x11:
+ case 0x2a:
+ case 0x34:
+ case 0x36:
+ fm_info_set_phy_address(FM1_DTSEC3, PHY_BASE_ADDR + 2);
+ fm_info_set_phy_address(FM1_DTSEC4, PHY_BASE_ADDR + 3);
+ break;
+ case 0x01:
+ case 0x02:
+ case 0x05:
+ case 0x07:
+ case 0x35:
+ fm_info_set_phy_address(FM1_DTSEC3, PHY_BASE_ADDR + 0);
+ fm_info_set_phy_address(FM1_DTSEC4, PHY_BASE_ADDR + 1);
+ break;
+ default:
+ break;
+ }
+ }
+
+ /*
+ * For 10G, we only support one XAUI card per Fman. If present, then we
+ * force its routing and never touch those bits again, which removes the
+ * need for Linux to do any muxing. This works because of the way
+ * BRDCFG1 is defined, but it's a bit hackish.
+ *
+ * The PHY address for the XAUI card depends on which slot it's in. The
+ * macros we use imply that the PHY address is based on which FM, but
+ * that's not true. On the P4080DS, FM1 could only use XAUI in slot 5,
+ * and FM2 could only use a XAUI in slot 4. On the Hydra board, we
+ * check the actual slot and just use the macros as-is, even though
+ * the P3041 and P5020 only have one Fman.
+ */
+ lane = serdes_get_first_lane(XAUI_FM1);
+ if (lane >= 0) {
+ debug("FM1@TGEC1 expects XAUI in slot %u\n", lane_to_slot[lane]);
+ mdio_mux[i].mask = BRDCFG1_EMI2_SEL_MASK;
+ mdio_mux[i].val = BRDCFG1_EMI2_SEL_SLOT2;
+ super_hydra_mdio_set_mux("SUPER_HYDRA_FM1_TGEC_MDIO",
+ mdio_mux[i].mask, mdio_mux[i].val);
+ }
+
+ fm_info_set_mdio(FM1_10GEC1,
+ miiphy_get_dev_by_name("SUPER_HYDRA_FM1_TGEC_MDIO"));
+
+#if (CONFIG_SYS_NUM_FMAN == 2)
+ for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
+ int idx = i - FM2_DTSEC1;
+
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_SGMII:
+ lane = serdes_get_first_lane(SGMII_FM2_DTSEC1 + idx);
+ if (lane < 0)
+ break;
+ slot = lane_to_slot[lane];
+ mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK;
+ debug("FM2@DTSEC%u expects SGMII in slot %u\n",
+ idx + 1, slot);
+ switch (slot) {
+ case 1:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT1 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 2:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT2 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 3:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT3 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 5:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT5 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 6:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT6 |
+ BRDCFG1_EMI1_EN;
+ break;
+ case 7:
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT7 |
+ BRDCFG1_EMI1_EN;
+ break;
+ };
+
+ if (i == FM2_DTSEC1 || i == FM2_DTSEC2) {
+ super_hydra_mdio_set_mux(
+ "SUPER_HYDRA_FM3_SGMII_MDIO",
+ mdio_mux[i].mask,
+ mdio_mux[i].val);
+ fm_info_set_mdio(i, miiphy_get_dev_by_name(
+ "SUPER_HYDRA_FM3_SGMII_MDIO"));
+ } else {
+ super_hydra_mdio_set_mux(
+ "SUPER_HYDRA_FM2_SGMII_MDIO",
+ mdio_mux[i].mask,
+ mdio_mux[i].val);
+ fm_info_set_mdio(i, miiphy_get_dev_by_name(
+ "SUPER_HYDRA_FM2_SGMII_MDIO"));
+ }
+
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ /*
+ * FM1 DTSEC5 is routed via EC1 to the first on-board
+ * RGMII port. FM2 DTSEC5 is routed via EC2 to the
+ * second on-board RGMII port. The other DTSECs cannot
+ * be routed to RGMII.
+ */
+ debug("FM2@DTSEC%u is RGMII at address %u\n",
+ idx + 1, 1);
+ fm_info_set_phy_address(i, 1);
+ mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK;
+ mdio_mux[i].val = BRDCFG1_EMI1_SEL_RGMII |
+ BRDCFG1_EMI1_EN;
+ super_hydra_mdio_set_mux("SUPER_HYDRA_RGMII_MDIO",
+ mdio_mux[i].mask, mdio_mux[i].val);
+ fm_info_set_mdio(i,
+ miiphy_get_dev_by_name("SUPER_HYDRA_RGMII_MDIO"));
+ break;
+ case PHY_INTERFACE_MODE_NONE:
+ fm_info_set_phy_address(i, 0);
+ break;
+ default:
+ printf("Fman2: DTSEC%u set to unknown interface %i\n",
+ idx + 1, fm_info_get_enet_if(i));
+ fm_info_set_phy_address(i, 0);
+ break;
+ }
+ }
+
+ bus = miiphy_get_dev_by_name("SUPER_HYDRA_FM2_SGMII_MDIO");
+ set_sgmii_phy(bus, FM2_DTSEC3, PORT_NUM_FM2, PHY_BASE_ADDR);
+ bus = miiphy_get_dev_by_name("SUPER_HYDRA_FM3_SGMII_MDIO");
+ set_sgmii_phy(bus, FM2_DTSEC1, PORT_NUM_FM2, PHY_BASE_ADDR);
+
+ /*
+ * For 10G, we only support one XAUI card per Fman. If present, then we
+ * force its routing and never touch those bits again, which removes the
+ * need for Linux to do any muxing. This works because of the way
+ * BRDCFG1 is defined, but it's a bit hackish.
+ *
+ * The PHY address for the XAUI card depends on which slot it's in. The
+ * macros we use imply that the PHY address is based on which FM, but
+ * that's not true. On the P4080DS, FM1 could only use XAUI in slot 5,
+ * and FM2 could only use a XAUI in slot 4. On the Hydra board, we
+ * check the actual slot and just use the macros as-is, even though
+ * the P3041 and P5020 only have one Fman.
+ */
+ lane = serdes_get_first_lane(XAUI_FM2);
+ if (lane >= 0) {
+ debug("FM2@TGEC1 expects XAUI in slot %u\n", lane_to_slot[lane]);
+ mdio_mux[i].mask = BRDCFG1_EMI2_SEL_MASK;
+ mdio_mux[i].val = BRDCFG1_EMI2_SEL_SLOT1;
+ super_hydra_mdio_set_mux("SUPER_HYDRA_FM2_TGEC_MDIO",
+ mdio_mux[i].mask, mdio_mux[i].val);
+ }
+
+ fm_info_set_mdio(FM2_10GEC1,
+ miiphy_get_dev_by_name("SUPER_HYDRA_FM2_TGEC_MDIO"));
+
+#endif
+
+ cpu_eth_init(bis);
+#endif
+
+ return pci_eth_init(bis);
+}
Code Review / kvmfornfv.git / blobdiff