--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <fsl_ifc.h>
+#include <hwconfig.h>
+#include <i2c.h>
+#include <fsl_ddr_sdram.h>
+
+#ifdef CONFIG_PCI
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#endif
+
+#include "../common/qixis.h"
+DECLARE_GLOBAL_DATA_PTR;
+
+
+int board_early_init_f(void)
+{
+ struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR;
+
+ setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT);
+
+ return 0;
+}
+
+void board_config_serdes_mux(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 pordevsr = in_be32(&gur->pordevsr);
+ u32 srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >>
+ MPC85xx_PORDEVSR_IO_SEL_SHIFT;
+
+ switch (srds_cfg) {
+ /* PEX(1) PEX(2) CPRI 2 CPRI 1 */
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ case 22:
+ case 23:
+ case 24:
+ case 25:
+ case 26:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x03);
+ break;
+
+ /* PEX(1) PEX(2) SGMII1 CPRI 1 */
+ case 6:
+ case 7:
+ case 8:
+ case 9:
+ case 10:
+ case 27:
+ case 28:
+ case 29:
+ case 30:
+ case 31:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x01);
+ break;
+
+ /* PEX(1) PEX(2) SGMII1 SGMII2 */
+ case 11:
+ case 32:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x00);
+ break;
+
+ /* PEX(1) SGMII2 CPRI 2 CPRI 1 */
+ case 12:
+ case 13:
+ case 14:
+ case 15:
+ case 16:
+ case 33:
+ case 34:
+ case 35:
+ case 36:
+ case 37:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x07);
+ break;
+
+ /* PEX(1) SGMII2 SGMII1 CPRI 1 */
+ case 17:
+ case 18:
+ case 19:
+ case 20:
+ case 21:
+ case 38:
+ case 39:
+ case 40:
+ case 41:
+ case 42:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x05);
+ break;
+
+ /* SGMII1 SGMII2 CPRI 2 CPRI 1 */
+ case 43:
+ case 44:
+ case 45:
+ case 46:
+ case 47:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x0F);
+ break;
+
+
+ default:
+ break;
+ }
+}
+
+/* Configure DSP DDR controller */
+void dsp_ddr_configure(void)
+{
+ /*
+ *There are separate DDR-controllers for DSP and PowerPC side DDR.
+ *copy the ddr controller settings from PowerPC side DDR controller
+ *to the DSP DDR controller as connected DDR memories are similar.
+ */
+ struct ccsr_ddr __iomem *pa_ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
+ struct ccsr_ddr temp_ddr;
+ struct ccsr_ddr __iomem *dsp_ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR;
+
+ memcpy(&temp_ddr, pa_ddr, sizeof(struct ccsr_ddr));
+ temp_ddr.cs0_bnds = CONFIG_SYS_DDR1_CS0_BNDS;
+ temp_ddr.sdram_cfg &= ~SDRAM_CFG_MEM_EN;
+ memcpy(dsp_ddr, &temp_ddr, sizeof(struct ccsr_ddr));
+ dsp_ddr->sdram_cfg |= SDRAM_CFG_MEM_EN;
+}
+
+int board_early_init_r(void)
+{
+#ifndef CONFIG_SYS_NO_FLASH
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_64M, 1);
+
+ set_tlb(1, flashbase + 0x4000000,
+ CONFIG_SYS_FLASH_BASE_PHYS + 0x4000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel+1, BOOKE_PAGESZ_64M, 1);
+#endif
+ board_config_serdes_mux();
+ dsp_ddr_configure();
+ return 0;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+#endif /* ifdef CONFIG_PCI */
+
+int checkboard(void)
+{
+ struct cpu_type *cpu;
+ u8 sw;
+
+ cpu = gd->arch.cpu;
+ printf("Board: %sQDS\n", cpu->name);
+
+ printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x,\n",
+ QIXIS_READ(id), QIXIS_READ(arch), QIXIS_READ(scver));
+
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+ printf("IFC chip select:");
+ switch (sw) {
+ case 0:
+ printf("NOR\n");
+ break;
+ case 2:
+ printf("Promjet\n");
+ break;
+ case 4:
+ printf("NAND\n");
+ break;
+ default:
+ printf("Invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+ break;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+ struct fsl_pq_mdio_info mdio_info;
+ struct tsec_info_struct tsec_info[4];
+ int num = 0;
+
+#ifdef CONFIG_TSEC1
+ SET_STD_TSEC_INFO(tsec_info[num], 1);
+ num++;
+
+#endif
+
+#ifdef CONFIG_TSEC2
+ SET_STD_TSEC_INFO(tsec_info[num], 2);
+ num++;
+#endif
+
+ mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+ mdio_info.name = DEFAULT_MII_NAME;
+
+ fsl_pq_mdio_init(bis, &mdio_info);
+ tsec_eth_init(bis, tsec_info, num);
+
+ #ifdef CONFIG_PCI
+ pci_eth_init(bis);
+ #endif
+
+ return 0;
+}
+#endif
+
+#define USBMUX_SEL_MASK 0xc0
+#define USBMUX_SEL_UART2 0xc0
+#define USBMUX_SEL_USB 0x40
+#define SPIMUX_SEL_UART3 0x80
+#define GPS_MUX_SEL_GPS 0x40
+
+#define TSEC_1588_CLKIN_MASK 0x03
+#define CON_XCVR_REF_CLK 0x00
+
+int misc_init_r(void)
+{
+ u8 val;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 porbmsr = in_be32(&gur->porbmsr);
+ u32 romloc = (porbmsr >> MPC85xx_PORBMSR_ROMLOC_SHIFT) & 0xf;
+
+ /*Configure 1588 clock-in source from RF Card*/
+ val = QIXIS_READ_I2C(brdcfg[5]);
+ QIXIS_WRITE_I2C(brdcfg[5],
+ (val & ~(TSEC_1588_CLKIN_MASK)) | CON_XCVR_REF_CLK);
+
+ if (hwconfig("uart2") && hwconfig("usb1")) {
+ printf("UART2 and USB cannot work together on the board\n");
+ printf("Remove one from hwconfig and reset\n");
+ } else {
+ if (hwconfig("uart2")) {
+ val = QIXIS_READ_I2C(brdcfg[5]);
+ QIXIS_WRITE_I2C(brdcfg[5],
+ (val & ~(USBMUX_SEL_MASK)) | USBMUX_SEL_UART2);
+ clrbits_be32(&gur->pmuxcr3,
+ MPC85xx_PMUXCR3_USB_SEL_MASK);
+ setbits_be32(&gur->pmuxcr3, MPC85xx_PMUXCR3_UART2_SEL);
+ } else {
+ /* By default USB should be selected.
+ * Programming FPGA to select USB. */
+ val = QIXIS_READ_I2C(brdcfg[5]);
+ QIXIS_WRITE_I2C(brdcfg[5],
+ (val & ~(USBMUX_SEL_MASK)) | USBMUX_SEL_USB);
+ }
+
+ }
+
+ if (hwconfig("sim")) {
+ if (romloc == PORBMSR_ROMLOC_NAND_2K ||
+ romloc == PORBMSR_ROMLOC_NOR ||
+ romloc == PORBMSR_ROMLOC_SPI) {
+
+ val = QIXIS_READ_I2C(brdcfg[3]);
+ QIXIS_WRITE_I2C(brdcfg[3], val|0x10);
+ clrbits_be32(&gur->pmuxcr,
+ MPC85xx_PMUXCR0_SIM_SEL_MASK);
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR0_SIM_SEL);
+ }
+ }
+
+ if (hwconfig("uart3")) {
+ if (romloc == PORBMSR_ROMLOC_NAND_2K ||
+ romloc == PORBMSR_ROMLOC_NOR ||
+ romloc == PORBMSR_ROMLOC_SDHC) {
+
+ /* UART3 and SPI1 (Flashes) are muxed together */
+ val = QIXIS_READ_I2C(brdcfg[3]);
+ QIXIS_WRITE_I2C(brdcfg[3], (val | SPIMUX_SEL_UART3));
+ clrbits_be32(&gur->pmuxcr3,
+ MPC85xx_PMUXCR3_UART3_SEL_MASK);
+ setbits_be32(&gur->pmuxcr3, MPC85xx_PMUXCR3_UART3_SEL);
+
+ /* MUX to select UART3 connection to J24 header
+ * or to GPS */
+ val = QIXIS_READ_I2C(brdcfg[6]);
+ if (hwconfig("gps"))
+ QIXIS_WRITE_I2C(brdcfg[6],
+ (val | GPS_MUX_SEL_GPS));
+ else
+ QIXIS_WRITE_I2C(brdcfg[6],
+ (val & ~(GPS_MUX_SEL_GPS)));
+ }
+ }
+ return 0;
+}
+
+void fdt_del_node_compat(void *blob, const char *compatible)
+{
+ int err;
+ int off = fdt_node_offset_by_compatible(blob, -1, compatible);
+ if (off < 0) {
+ printf("WARNING: could not find compatible node %s: %s.\n",
+ compatible, fdt_strerror(off));
+ return;
+ }
+ err = fdt_del_node(blob, off);
+ if (err < 0) {
+ printf("WARNING: could not remove %s: %s.\n",
+ compatible, fdt_strerror(err));
+ }
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ #if defined(CONFIG_PCI)
+ FT_FSL_PCI_SETUP;
+ #endif
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 porbmsr = in_be32(&gur->porbmsr);
+ u32 romloc = (porbmsr >> MPC85xx_PORBMSR_ROMLOC_SHIFT) & 0xf;
+
+ if (!(hwconfig("uart2") && hwconfig("usb1"))) {
+ /* If uart2 is there in hwconfig remove usb node from
+ * device tree */
+
+ if (hwconfig("uart2")) {
+ /* remove dts usb node */
+ fdt_del_node_compat(blob, "fsl-usb2-dr");
+ } else {
+ fdt_fixup_dr_usb(blob, bd);
+ fdt_del_node_and_alias(blob, "serial2");
+ }
+ }
+
+ if (hwconfig("uart3")) {
+ if (romloc == PORBMSR_ROMLOC_NAND_2K ||
+ romloc == PORBMSR_ROMLOC_NOR ||
+ romloc == PORBMSR_ROMLOC_SDHC)
+ /* Delete SPI node from the device tree */
+ fdt_del_node_and_alias(blob, "spi1");
+ } else
+ fdt_del_node_and_alias(blob, "serial3");
+
+ if (hwconfig("sim")) {
+ if (romloc == PORBMSR_ROMLOC_NAND_2K ||
+ romloc == PORBMSR_ROMLOC_NOR ||
+ romloc == PORBMSR_ROMLOC_SPI) {
+
+ /* remove dts sdhc node */
+ fdt_del_node_compat(blob, "fsl,esdhc");
+ } else if (romloc == PORBMSR_ROMLOC_SDHC) {
+
+ /* remove dts sim node */
+ fdt_del_node_compat(blob, "fsl,sim-v1.0");
+ printf("SIM & SDHC can't work together on the board");
+ printf("\nRemove sim from hwconfig and reset\n");
+ }
+ }
+}
+#endif
Code Review / kvmfornfv.git / blobdiff