Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / board / esg / ima3-mx53 / imximage.cfg

diff --git a/qemu/roms/u-boot/board/esg/ima3-mx53/imximage.cfg b/qemu/roms/u-boot/board/esg/ima3-mx53/imximage.cfg
new file mode 100644 (file)
index 0000000..324a90e
--- /dev/null
+++ b/qemu/roms/u-boot/board/esg/ima3-mx53/imximage.cfg
@@ -0,0 +1,104 @@
+/*
+ * (C) Copyright 2012
+ * Stefano Babic DENX Software Engineering sbabic@denx.de.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
+BOOT_FROM      nor
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *     Addr-type register length (1,2 or 4 bytes)
+ *     Address   absolute address of the register
+ *     value     value to be stored in the register
+ */
+/* IOMUX for RAM only */
+DATA 4 0x53fa8554 0x300020
+DATA 4 0x53fa8560 0x300020
+DATA 4 0x53fa8594 0x300020
+DATA 4 0x53fa8584 0x300020
+DATA 4 0x53fa8558 0x300040
+DATA 4 0x53fa8568 0x300040
+DATA 4 0x53fa8590 0x300040
+DATA 4 0x53fa857c 0x300040
+DATA 4 0x53fa8564 0x300040
+DATA 4 0x53fa8580 0x300040
+DATA 4 0x53fa8570 0x300220
+DATA 4 0x53fa8578 0x300220
+DATA 4 0x53fa872c 0x300000
+DATA 4 0x53fa8728 0x300000
+DATA 4 0x53fa871c 0x300000
+DATA 4 0x53fa8718 0x300000
+DATA 4 0x53fa8574 0x300020
+DATA 4 0x53fa8588 0x300020
+DATA 4 0x53fa855c 0x0
+DATA 4 0x53fa858c 0x0
+DATA 4 0x53fa856c 0x300040
+DATA 4 0x53fa86f0 0x300000
+DATA 4 0x53fa8720 0x300000
+DATA 4 0x53fa86fc 0x0
+DATA 4 0x53fa86f4 0x0
+DATA 4 0x53fa8714 0x0
+DATA 4 0x53fa8724 0x4000000
+
+/* DDR RAM */
+DATA 4 0x63fd9088 0x40404040
+DATA 4 0x63fd9090 0x40404040
+DATA 4 0x63fd907C 0x01420143
+DATA 4 0x63fd9080 0x01450146
+DATA 4 0x63fd9018 0x00111740
+DATA 4 0x63fd9000 0x84190000
+
+/* esdcfgX */
+DATA 4 0x63fd900C 0x9f5152e3
+DATA 4 0x63fd9010 0xb68e8a63
+DATA 4 0x63fd9014 0x01ff00db
+
+/* Read/Write command delay */
+DATA 4 0x63fd902c 0x000026d2
+
+/* Out of reset delays */
+DATA 4 0x63fd9030 0x00ff0e21
+
+/* ESDCTL ODT timing control */
+DATA 4 0x63fd9008 0x12273030
+
+/* ESDCTL power down control */
+DATA 4 0x63fd9004 0x0002002d
+
+/* Set registers in DDR memory chips */
+DATA 4 0x63fd901c 0x00008032
+DATA 4 0x63fd901c 0x00008033
+DATA 4 0x63fd901c 0x00028031
+DATA 4 0x63fd901c 0x052080b0
+DATA 4 0x63fd901c 0x04008040
+
+/* ESDCTL refresh control */
+DATA 4 0x63fd9020 0x00005800
+
+/* PHY ZQ HW control */
+DATA 4 0x63fd9040 0x05380003
+
+/* PHY ODT control */
+DATA 4 0x63fd9058 0x00022222
+
+/* start DDR3 */
+DATA 4 0x63fd901c 0x00000000