Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / board / esd / pmc440 / init.S

diff --git a/qemu/roms/u-boot/board/esd/pmc440/init.S b/qemu/roms/u-boot/board/esd/pmc440/init.S
new file mode 100644 (file)
index 0000000..1f26fad
--- /dev/null
+++ b/qemu/roms/u-boot/board/esd/pmc440/init.S
@@ -0,0 +1,69 @@
+/*
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <ppc_asm.tmpl>
+#include <asm/mmu.h>
+#include <config.h>
+
+/*
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ */
+    .section .bootpg,"ax"
+    .globl tlbtab
+
+tlbtab:
+       tlbtab_start
+
+       /*
+        * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+        * speed up boot process. It is patched after relocation to enable SA_I
+        */
+       tlbentry( CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G )
+
+       /* TLB entries for DDR2 SDRAM are generated dynamically */
+
+#ifdef CONFIG_SYS_INIT_RAM_DCACHE
+       /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
+       tlbentry( CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G )
+#endif
+
+       /* TLB-entry for PCI Memory */
+       tlbentry( CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG )
+       tlbentry( CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG )
+       tlbentry( CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG )
+       tlbentry( CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG )
+
+       /* TLB-entries for EBC */
+       /* PMC440 maps EBC to 0xef000000 which is handled by the peripheral
+        * tlb entry.
+        * This dummy entry is only for convinience in order not to modify the
+        * amount of entries. Currently OS/9 relies on this :-)
+        */
+       tlbentry( 0xc0000000, SZ_256M, 0xc0000000, 1, AC_RWX | SA_IG )
+
+       /* TLB-entry for NAND */
+       tlbentry( CONFIG_SYS_NAND_ADDR, SZ_1K, CONFIG_SYS_NAND_ADDR, 1, AC_RWX | SA_IG )
+
+       /* TLB-entry for Internal Registers & OCM */
+       tlbentry( 0xe0000000, SZ_16M, 0xe0000000, 0,  AC_RWX | SA_I )
+
+       /*TLB-entry PCI registers*/
+       tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1,  AC_RWX | SA_IG )
+
+       /* TLB-entry for peripherals */
+       tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG)
+
+       /* TLB-entry PCI IO space */
+       tlbentry(0xE8000000, SZ_64K, 0xE8000000, 1, AC_RWX | SA_IG)
+
+       /* TODO:  what about high IO space */
+       tlbtab_end