--- /dev/null
+/*
+ *
+ * (c) 2009 Emcraft Systems, Ilya Yanok <yanok@emcraft.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <power/pmic.h>
+#include <fsl_pmic.h>
+#include <asm/gpio.h>
+#include "qong_fpga.h"
+#include <watchdog.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ /* dram_init must store complete ramsize in gd->ram_size */
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ PHYS_SDRAM_1_SIZE);
+ return 0;
+}
+
+static void qong_fpga_reset(void)
+{
+ gpio_set_value(QONG_FPGA_RST_PIN, 0);
+ udelay(30);
+ gpio_set_value(QONG_FPGA_RST_PIN, 1);
+
+ udelay(300);
+}
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_QONG_FPGA
+ /* CS1: FPGA/Network Controller/GPIO, 16-bit, no DTACK */
+ static const struct mxc_weimcs cs1 = {
+ /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+ CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 0, 10, 0, 0, 1),
+ /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+ CSCR_L(2, 0, 0, 4, 0, 0, 5, 0, 0, 0, 0, 1),
+ /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+ CSCR_A(0, 4, 0, 2, 0, 0, 3, 0, 0, 0, 0, 0, 0, 0)
+ };
+
+ mxc_setup_weimcs(1, &cs1);
+
+ /* setup pins for FPGA */
+ mx31_gpio_mux(IOMUX_MODE(0x76, MUX_CTL_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(0x7e, MUX_CTL_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(0x91, MUX_CTL_OUT_FUNC | MUX_CTL_IN_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(0x92, MUX_CTL_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(0x93, MUX_CTL_GPIO));
+
+ /* FPGA reset Pin */
+ /* rstn = 0 */
+ gpio_direction_output(QONG_FPGA_RST_PIN, 0);
+
+ /* set interrupt pin as input */
+ gpio_direction_input(QONG_FPGA_IRQ_PIN);
+
+ /* FPGA JTAG Interface */
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SFS6, MUX_CTL_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SCK6, MUX_CTL_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_CAPTURE, MUX_CTL_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_COMPARE, MUX_CTL_GPIO));
+ gpio_direction_output(QONG_FPGA_TCK_PIN, 0);
+ gpio_direction_output(QONG_FPGA_TMS_PIN, 0);
+ gpio_direction_output(QONG_FPGA_TDI_PIN, 0);
+ gpio_direction_input(QONG_FPGA_TDO_PIN);
+#endif
+
+ /* setup pins for UART1 */
+ mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
+ mx31_gpio_mux(MUX_TXD1__UART1_TXD_MUX);
+ mx31_gpio_mux(MUX_RTS1__UART1_RTS_B);
+ mx31_gpio_mux(MUX_CTS1__UART1_CTS_B);
+
+ /* setup pins for SPI (pmic) */
+ mx31_gpio_mux(MUX_CSPI2_SS0__CSPI2_SS0_B);
+ mx31_gpio_mux(MUX_CSPI2_MOSI__CSPI2_MOSI);
+ mx31_gpio_mux(MUX_CSPI2_MISO__CSPI2_MISO);
+ mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK);
+ mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B);
+
+ /* Setup pins for USB2 Host */
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_CLK, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DIR, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_NXT, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_STP, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA0, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA1, MUX_CTL_FUNC));
+
+#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
+ PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
+
+ mx31_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
+ mx31_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
+ mx31_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG); /* USBH2_DATA2 */
+ mx31_set_pad(MX31_PIN_STXD6, H2_PAD_CFG); /* USBH2_DATA3 */
+ mx31_set_pad(MX31_PIN_SFS3, H2_PAD_CFG); /* USBH2_DATA4 */
+ mx31_set_pad(MX31_PIN_SCK3, H2_PAD_CFG); /* USBH2_DATA5 */
+ mx31_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG); /* USBH2_DATA6 */
+ mx31_set_pad(MX31_PIN_STXD3, H2_PAD_CFG); /* USBH2_DATA7 */
+
+ mx31_set_gpr(MUX_PGP_UH2, 1);
+
+ return 0;
+
+}
+
+int board_init(void)
+{
+ /* Chip selects */
+ /* CS0: Nor Flash #0 - it must be init'ed when executing from DDR */
+ /* Assumptions: HCLK = 133 MHz, tACC = 130ns */
+ static const struct mxc_weimcs cs0 = {
+ /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+ CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 3, 21, 0, 0, 6),
+ /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+ CSCR_L(0, 1, 3, 3, 1, 1, 5, 1, 0, 0, 0, 1),
+ /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+ CSCR_A(0, 1, 2, 2, 0, 0, 2, 0, 0, 0, 0, 0, 0, 0)
+ };
+
+ mxc_setup_weimcs(0, &cs0);
+
+ /* board id for linux */
+ gd->bd->bi_arch_number = MACH_TYPE_QONG;
+ gd->bd->bi_boot_params = (0x80000100); /* adress of boot parameters */
+
+ qong_fpga_init();
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ u32 val;
+ struct pmic *p;
+ int ret;
+
+ ret = pmic_init(I2C_PMIC);
+ if (ret)
+ return ret;
+
+ p = pmic_get("FSL_PMIC");
+ if (!p)
+ return -ENODEV;
+ /* Enable RTC battery */
+ pmic_reg_read(p, REG_POWER_CTL0, &val);
+ pmic_reg_write(p, REG_POWER_CTL0, val | COINCHEN);
+ pmic_reg_write(p, REG_INT_STATUS1, RTCRSTI);
+
+#ifdef CONFIG_HW_WATCHDOG
+ hw_watchdog_init();
+#endif
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ printf("Board: DAVE/DENX Qong\n");
+ return 0;
+}
+
+int misc_init_r(void)
+{
+#ifdef CONFIG_QONG_FPGA
+ u32 tmp;
+
+ tmp = *(volatile u32*)QONG_FPGA_CTRL_VERSION;
+ printf("FPGA: ");
+ printf("version register = %u.%u.%u\n",
+ (tmp & 0xF000) >> 12, (tmp & 0x0F00) >> 8, tmp & 0x00FF);
+#endif
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_QONG_FPGA) && defined(CONFIG_DNET)
+ return dnet_eth_initialize(0, (void *)CONFIG_DNET_BASE, -1);
+#else
+ return 0;
+#endif
+}
+
+#if defined(CONFIG_QONG_FPGA) && defined(CONFIG_NAND_PLAT)
+static void board_nand_setup(void)
+{
+ /* CS3: NAND 8-bit */
+ static const struct mxc_weimcs cs3 = {
+ /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+ CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 1, 15, 0, 0, 0),
+ /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+ CSCR_L(2, 0, 0, 1, 3, 1, 3, 3, 0, 0, 0, 1),
+ /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+ CSCR_A(0, 0, 0, 2, 0, 0, 2, 0, 0, 0, 0, 0, 0, 0)
+ };
+
+ mxc_setup_weimcs(3, &cs3);
+
+ mx31_set_gpr(MUX_SDCTL_CSD1_SEL, 1);
+
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_WP, MUX_CTL_IN_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_CE, MUX_CTL_IN_GPIO));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_RB, MUX_CTL_IN_GPIO));
+
+ /* Make sure to reset the fpga else you cannot access NAND */
+ qong_fpga_reset();
+
+ /* Enable NAND flash */
+ gpio_set_value(15, 1);
+ gpio_set_value(14, 1);
+ gpio_direction_output(15, 0);
+ gpio_direction_input(16);
+ gpio_direction_input(14);
+
+}
+
+int qong_nand_rdy(void *chip)
+{
+ udelay(1);
+ return gpio_get_value(16);
+}
+
+void qong_nand_select_chip(struct mtd_info *mtd, int chip)
+{
+ if (chip >= 0)
+ gpio_set_value(15, 0);
+ else
+ gpio_set_value(15, 1);
+
+}
+
+void qong_nand_plat_init(void *chip)
+{
+ struct nand_chip *nand = (struct nand_chip *)chip;
+ nand->chip_delay = 20;
+ nand->select_chip = qong_nand_select_chip;
+ nand->options &= ~NAND_BUSWIDTH_16;
+ board_nand_setup();
+}
+
+#endif
Code Review / kvmfornfv.git / blobdiff