--- /dev/null
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/sizes.h>
+#include <asm/arch/at91sam9263.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_matrix.h>
+#include <asm/arch/at91_pio.h>
+#include <asm/arch/clk.h>
+#include <asm/io.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/hardware.h>
+#include <lcd.h>
+#include <atmel_lcdc.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+#include <atmel_mci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+#ifdef CONFIG_CMD_NAND
+static void at91sam9263ek_nand_hw_init(void)
+{
+ unsigned long csa;
+ at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0;
+ at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
+ at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+
+ /* Enable CS3 */
+ csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
+ writel(csa, &matrix->csa[0]);
+
+ /* Enable CS3 */
+
+ /* Configure SMC CS3 for NAND/SmartMedia */
+ writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+
+ writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+ AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+ &smc->cs[3].pulse);
+
+ writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+ &smc->cs[3].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+ AT91_SMC_MODE_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+ AT91_SMC_MODE_DBW_8 |
+#endif
+ AT91_SMC_MODE_TDF_CYCLE(2),
+ &smc->cs[3].mode);
+
+ writel(1 << ATMEL_ID_PIOA | 1 << ATMEL_ID_PIOCDE,
+ &pmc->pcer);
+
+ /* Configure RDY/BSY */
+ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+ /* Enable NandFlash */
+ at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+#endif
+
+#ifdef CONFIG_MACB
+static void at91sam9263ek_macb_hw_init(void)
+{
+ at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+ at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
+
+ /* Enable clock */
+ writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
+
+ /*
+ * Disable pull-up on:
+ * RXDV (PC25) => PHY normal mode (not Test mode)
+ * ERX0 (PE25) => PHY ADDR0
+ * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
+ *
+ * PHY has internal pull-down
+ */
+ writel(1 << 25, &pio->pioc.pudr);
+ writel((1 << 25) | (1 <<26), &pio->pioe.pudr);
+
+ at91_phy_reset();
+
+ /* Re-enable pull-up */
+ writel(1 << 25, &pio->pioc.puer);
+ writel((1 << 25) | (1 <<26), &pio->pioe.puer);
+
+ at91_macb_hw_init();
+}
+#endif
+
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+ vl_col: 240,
+ vl_row: 320,
+ vl_clk: 4965000,
+ vl_sync: ATMEL_LCDC_INVLINE_INVERTED |
+ ATMEL_LCDC_INVFRAME_INVERTED,
+ vl_bpix: 3,
+ vl_tft: 1,
+ vl_hsync_len: 5,
+ vl_left_margin: 1,
+ vl_right_margin:33,
+ vl_vsync_len: 1,
+ vl_upper_margin:1,
+ vl_lower_margin:0,
+ mmio: ATMEL_BASE_LCDC,
+};
+
+void lcd_enable(void)
+{
+ at91_set_pio_value(AT91_PIO_PORTA, 30, 1); /* power up */
+}
+
+void lcd_disable(void)
+{
+ at91_set_pio_value(AT91_PIO_PORTA, 30, 0); /* power down */
+}
+
+static void at91sam9263ek_lcd_hw_init(void)
+{
+ at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+
+ at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */
+ at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */
+ at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */
+ at91_set_b_periph(AT91_PIO_PORTB, 9, 0); /* LCDCC */
+ at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD2 */
+ at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD3 */
+ at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD4 */
+ at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD5 */
+ at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD6 */
+ at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD7 */
+ at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD10 */
+ at91_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD11 */
+ at91_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD12 */
+ at91_set_b_periph(AT91_PIO_PORTC, 12, 0); /* LCDD13 */
+ at91_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD14 */
+ at91_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD15 */
+ at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD18 */
+ at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD19 */
+ at91_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDD20 */
+ at91_set_b_periph(AT91_PIO_PORTC, 17, 0); /* LCDD21 */
+ at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */
+ at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */
+
+ writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
+ gd->fb_base = ATMEL_BASE_SRAM0;
+}
+
+#ifdef CONFIG_LCD_INFO
+#include <nand.h>
+#include <version.h>
+
+#ifndef CONFIG_SYS_NO_FLASH
+extern flash_info_t flash_info[];
+#endif
+
+void lcd_show_board_info(void)
+{
+ ulong dram_size, nand_size;
+#ifndef CONFIG_SYS_NO_FLASH
+ ulong flash_size;
+#endif
+ int i;
+ char temp[32];
+
+ lcd_printf ("%s\n", U_BOOT_VERSION);
+ lcd_printf ("(C) 2008 ATMEL Corp\n");
+ lcd_printf ("at91support@atmel.com\n");
+ lcd_printf ("%s CPU at %s MHz\n",
+ ATMEL_CPU_NAME,
+ strmhz(temp, get_cpu_clk_rate()));
+
+ dram_size = 0;
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+ dram_size += gd->bd->bi_dram[i].size;
+ nand_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+ nand_size += nand_info[i].size;
+#ifndef CONFIG_SYS_NO_FLASH
+ flash_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
+ flash_size += flash_info[i].size;
+#endif
+ lcd_printf (" %ld MB SDRAM, %ld MB NAND",
+ dram_size >> 20,
+ nand_size >> 20 );
+#ifndef CONFIG_SYS_NO_FLASH
+ lcd_printf (",\n %ld MB NOR",
+ flash_size >> 20);
+#endif
+ lcd_puts ("\n");
+}
+#endif /* CONFIG_LCD_INFO */
+#endif
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+int board_mmc_init(bd_t *bd)
+{
+ at91_mci_hw_init();
+
+ return atmel_mci_init((void *)ATMEL_BASE_MCI1);
+}
+#endif
+
+int board_early_init_f(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+ /* Enable clocks for all PIOs */
+ writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
+ (1 << ATMEL_ID_PIOCDE),
+ &pmc->pcer);
+
+ at91_seriald_hw_init();
+ return 0;
+}
+
+int board_init(void)
+{
+ /* arch number of AT91SAM9263EK-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9263EK;
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_CMD_NAND
+ at91sam9263ek_nand_hw_init();
+#endif
+#ifdef CONFIG_HAS_DATAFLASH
+ at91_set_pio_output(AT91_PIO_PORTE, 20, 1); /* select spi0 clock */
+ at91_spi0_hw_init(1 << 0);
+#endif
+#ifdef CONFIG_MACB
+ at91sam9263ek_macb_hw_init();
+#endif
+#ifdef CONFIG_USB_OHCI_NEW
+ at91_uhp_hw_init();
+#endif
+#ifdef CONFIG_LCD
+ at91sam9263ek_lcd_hw_init();
+#endif
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *) ATMEL_BASE_EMAC, 0x00);
+#endif
+ return rc;
+}
Code Review / kvmfornfv.git / blobdiff