Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / board / amcc / yosemite / init.S

diff --git a/qemu/roms/u-boot/board/amcc/yosemite/init.S b/qemu/roms/u-boot/board/amcc/yosemite/init.S
new file mode 100644 (file)
index 0000000..529cc65
--- /dev/null
+++ b/qemu/roms/u-boot/board/amcc/yosemite/init.S
@@ -0,0 +1,49 @@
+/*
+ * SPDX-License-Identifier:    GPL-2.0+
+*/
+
+#include <asm-offsets.h>
+#include <ppc_asm.tmpl>
+#include <asm/mmu.h>
+#include <config.h>
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+
+    .section .bootpg,"ax"
+    .globl tlbtab
+
+tlbtab:
+    tlbtab_start
+
+    /*
+     * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+     * speed up boot process. It is patched after relocation to enable SA_I
+     */
+    tlbentry( CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 0, AC_RWX | SA_G/*|SA_I*/)
+
+    /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
+    tlbentry( CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G )
+
+    tlbentry( CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_RWX | SA_IG )
+    tlbentry( CONFIG_SYS_PCI_BASE, SZ_256M, CONFIG_SYS_PCI_BASE, 0, AC_RW | SA_IG )
+    tlbentry( CONFIG_SYS_NVRAM_BASE_ADDR, SZ_256M, CONFIG_SYS_NVRAM_BASE_ADDR, 0, AC_RWX | SA_W|SA_I )
+
+    /* PCI */
+    tlbentry( CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 0, AC_RW | SA_IG )
+    tlbentry( CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 0, AC_RW | SA_IG )
+    tlbentry( CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 0, AC_RW | SA_IG )
+    tlbentry( CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 0, AC_RW | SA_IG )
+
+    /* USB 2.0 Device */
+    tlbentry( CONFIG_SYS_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_RW | SA_IG )
+
+    tlbtab_end