--- /dev/null
+/*
+ * (C) Copyright 2006-2009
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2006
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/ppc4xx.h>
+#include <asm/ppc4xx-gpio.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/bitops.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if !defined(CONFIG_SYS_NO_FLASH)
+extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
+#endif
+
+extern void __ft_board_setup(void *blob, bd_t *bd);
+ulong flash_get_size(ulong base, int banknum);
+
+static inline u32 get_async_pci_freq(void)
+{
+ if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) &
+ CONFIG_SYS_BCSR5_PCI66EN)
+ return 66666666;
+ else
+ return 33333333;
+}
+
+int board_early_init_f(void)
+{
+ u32 sdr0_cust0;
+ u32 sdr0_pfc1, sdr0_pfc2;
+ u32 reg;
+
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, 0xb8400000);
+
+ /*
+ * Setup the interrupt controller polarities, triggers, etc.
+ */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+ mtdcr(UIC0ER, 0x00000000); /* disable all */
+ mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */
+ mtdcr(UIC0PR, 0xfffff7ff); /* per ref-board manual */
+ mtdcr(UIC0TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+ mtdcr(UIC1ER, 0x00000000); /* disable all */
+ mtdcr(UIC1CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC1PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC1TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC2SR, 0xffffffff); /* clear all */
+ mtdcr(UIC2ER, 0x00000000); /* disable all */
+ mtdcr(UIC2CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC2PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC2TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC2SR, 0xffffffff); /* clear all */
+
+ /* Check and reconfigure the PCI sync clock if necessary */
+ ppc4xx_pci_sync_clock_config(get_async_pci_freq());
+
+ /* 50MHz tmrclk */
+ out_8((u8 *) CONFIG_SYS_BCSR_BASE + 0x04, 0x00);
+
+ /* clear write protects */
+ out_8((u8 *) CONFIG_SYS_BCSR_BASE + 0x07, 0x00);
+
+ /* enable Ethernet */
+ out_8((u8 *) CONFIG_SYS_BCSR_BASE + 0x08, 0x00);
+
+ /* enable USB device */
+ out_8((u8 *) CONFIG_SYS_BCSR_BASE + 0x09, 0x20);
+
+ /* select Ethernet (and optionally IIC1) pins */
+ mfsdr(SDR0_PFC1, sdr0_pfc1);
+ sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) |
+ SDR0_PFC1_SELECT_CONFIG_4;
+#ifdef CONFIG_I2C_MULTI_BUS
+ sdr0_pfc1 |= ((sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_IIC1_SEL);
+#endif
+ /* Two UARTs, so we need 4-pin mode. Also, we want CTS/RTS mode. */
+ sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_4PINS;
+ sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U0ME_CTS_RTS;
+ sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_CTS_RTS;
+
+ mfsdr(SDR0_PFC2, sdr0_pfc2);
+ sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) |
+ SDR0_PFC2_SELECT_CONFIG_4;
+ mtsdr(SDR0_PFC2, sdr0_pfc2);
+ mtsdr(SDR0_PFC1, sdr0_pfc1);
+
+ /* PCI arbiter enabled */
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg);
+
+ /* setup NAND FLASH */
+ mfsdr(SDR0_CUST0, sdr0_cust0);
+ sdr0_cust0 = SDR0_CUST0_MUX_NDFC_SEL |
+ SDR0_CUST0_NDFC_ENABLE |
+ SDR0_CUST0_NDFC_BW_8_BIT |
+ SDR0_CUST0_NDFC_ARE_MASK |
+ (0x80000000 >> (28 + CONFIG_SYS_NAND_CS));
+ mtsdr(SDR0_CUST0, sdr0_cust0);
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+#if !defined(CONFIG_SYS_NO_FLASH)
+ uint pbcr;
+ int size_val = 0;
+#endif
+#ifdef CONFIG_440EPX
+ unsigned long usb2d0cr = 0;
+ unsigned long usb2phy0cr, usb2h0cr = 0;
+ unsigned long sdr0_pfc1;
+ char *act = getenv("usbact");
+#endif
+ u32 reg;
+
+#if !defined(CONFIG_SYS_NO_FLASH)
+ /* Re-do flash sizing to get full correct info */
+
+ /* adjust flash start and offset */
+ gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+ gd->bd->bi_flashoffset = 0;
+
+#if defined(CONFIG_SYS_RAMBOOT)
+ mtdcr(EBC0_CFGADDR, PB3CR);
+#else
+ mtdcr(EBC0_CFGADDR, PB0CR);
+#endif
+ pbcr = mfdcr(EBC0_CFGDATA);
+ size_val = ffs(gd->bd->bi_flashsize) - 21;
+ pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
+#if defined(CONFIG_SYS_RAMBOOT)
+ mtdcr(EBC0_CFGADDR, PB3CR);
+#else
+ mtdcr(EBC0_CFGADDR, PB0CR);
+#endif
+ mtdcr(EBC0_CFGDATA, pbcr);
+
+ /*
+ * Re-check to get correct base address
+ */
+ flash_get_size(gd->bd->bi_flashstart, 0);
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+ /* Monitor protection ON by default */
+ (void)flash_protect(FLAG_PROTECT_SET,
+ -CONFIG_SYS_MONITOR_LEN,
+ 0xffffffff,
+ &flash_info[0]);
+
+ /* Env protection ON by default */
+ (void)flash_protect(FLAG_PROTECT_SET,
+ CONFIG_ENV_ADDR_REDUND,
+ CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
+ &flash_info[0]);
+#endif
+#endif /* CONFIG_SYS_NO_FLASH */
+
+ /*
+ * USB suff...
+ */
+#ifdef CONFIG_440EPX
+ if (act == NULL || strcmp(act, "hostdev") == 0) {
+ /* SDR Setting */
+ mfsdr(SDR0_PFC1, sdr0_pfc1);
+ mfsdr(SDR0_USB2D0CR, usb2d0cr);
+ mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+ mfsdr(SDR0_USB2H0CR, usb2h0cr);
+
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;
+
+ /*
+ * An 8-bit/60MHz interface is the only possible alternative
+ * when connecting the Device to the PHY
+ */
+ usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
+ usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;
+
+ /*
+ * To enable the USB 2.0 Device function
+ * through the UTMI interface
+ */
+ usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
+ usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION;
+
+ sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
+ sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL;
+
+ mtsdr(SDR0_PFC1, sdr0_pfc1);
+ mtsdr(SDR0_USB2D0CR, usb2d0cr);
+ mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+ mtsdr(SDR0_USB2H0CR, usb2h0cr);
+
+ /*clear resets*/
+ udelay (1000);
+ mtsdr(SDR0_SRST1, 0x00000000);
+ udelay (1000);
+ mtsdr(SDR0_SRST0, 0x00000000);
+
+ printf("USB: Host(int phy) Device(ext phy)\n");
+
+ } else if (strcmp(act, "dev") == 0) {
+ /*-------------------PATCH-------------------------------*/
+ mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;
+ mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+
+ udelay (1000);
+ mtsdr(SDR0_SRST1, 0x672c6000);
+
+ udelay (1000);
+ mtsdr(SDR0_SRST0, 0x00000080);
+
+ udelay (1000);
+ mtsdr(SDR0_SRST1, 0x60206000);
+
+ *(unsigned int *)(0xe0000350) = 0x00000001;
+
+ udelay (1000);
+ mtsdr(SDR0_SRST1, 0x60306000);
+ /*-------------------PATCH-------------------------------*/
+
+ /* SDR Setting */
+ mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+ mfsdr(SDR0_USB2H0CR, usb2h0cr);
+ mfsdr(SDR0_USB2D0CR, usb2d0cr);
+ mfsdr(SDR0_PFC1, sdr0_pfc1);
+
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_DEV;
+ usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_DEV;
+
+ usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
+ usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_8BIT_60MHZ;
+
+ usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
+ usb2d0cr = usb2d0cr | SDR0_USB2D0CR_EBC_SELECTION;
+
+ sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
+ sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL;
+
+ mtsdr(SDR0_USB2H0CR, usb2h0cr);
+ mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+ mtsdr(SDR0_USB2D0CR, usb2d0cr);
+ mtsdr(SDR0_PFC1, sdr0_pfc1);
+
+ /* clear resets */
+ udelay (1000);
+ mtsdr(SDR0_SRST1, 0x00000000);
+ udelay (1000);
+ mtsdr(SDR0_SRST0, 0x00000000);
+
+ printf("USB: Device(int phy)\n");
+ }
+#endif /* CONFIG_440EPX */
+
+ mfsdr(SDR0_SRST1, reg); /* enable security/kasumi engines */
+ reg &= ~(SDR0_SRST1_CRYP0 | SDR0_SRST1_KASU0);
+ mtsdr(SDR0_SRST1, reg);
+
+ /*
+ * Clear PLB4A0_ACR[WRP]
+ * This fix will make the MAL burst disabling patch for the Linux
+ * EMAC driver obsolete.
+ */
+ reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
+ mtdcr(PLB4A0_ACR, reg);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ char buf[64];
+ int i = getenv_f("serial#", buf, sizeof(buf));
+ u8 rev;
+ u32 clock = get_async_pci_freq();
+
+#ifdef CONFIG_440EPX
+ printf("Board: Sequoia - AMCC PPC440EPx Evaluation Board");
+#else
+ printf("Board: Rainier - AMCC PPC440GRx Evaluation Board");
+#endif
+
+ rev = in_8((void *)(CONFIG_SYS_BCSR_BASE + 0));
+ printf(", Rev. %X, PCI-Async=%d MHz", rev, clock / 1000000);
+
+ if (i > 0) {
+ puts(", serial# ");
+ puts(buf);
+ }
+ putc('\n');
+
+ /*
+ * Reconfiguration of the PCI sync clock is already done,
+ * now check again if everything is in range:
+ */
+ if (ppc4xx_pci_sync_clock_config(clock)) {
+ printf("ERROR: PCI clocking incorrect (async=%d "
+ "sync=%ld)!\n", clock, get_PCI_freq());
+ }
+
+ return (0);
+}
+
+#if defined(CONFIG_PCI) && defined(CONFIG_PCI_PNP)
+/*
+ * Assign interrupts to PCI devices.
+ */
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+{
+ pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
+}
+#endif
+
+#if defined(CONFIG_SYS_RAMBOOT)
+/*
+ * On NAND-booting sequoia, we need to patch the chips select numbers
+ * in the dtb (CS0 - NAND, CS3 - NOR)
+ */
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ int rc;
+ int len;
+ int nodeoffset;
+ struct fdt_property *prop;
+ u32 *reg;
+ char path[32];
+
+ /* First do common fdt setup */
+ __ft_board_setup(blob, bd);
+
+ /* And now configure NOR chip select to 3 instead of 0 */
+ strcpy(path, "/plb/opb/ebc/nor_flash@0,0");
+ nodeoffset = fdt_path_offset(blob, path);
+ prop = fdt_get_property_w(blob, nodeoffset, "reg", &len);
+ if (prop == NULL) {
+ printf("Unable to update NOR chip select for NAND booting\n");
+ return;
+ }
+ reg = (u32 *)&prop->data[0];
+ reg[0] = 3;
+ rc = fdt_find_and_setprop(blob, path, "reg", reg, 3 * sizeof(u32), 1);
+ if (rc) {
+ printf("Unable to update property NOR mappings, err=%s\n",
+ fdt_strerror(rc));
+ return;
+ }
+
+ /* And now configure NAND chip select to 0 instead of 3 */
+ strcpy(path, "/plb/opb/ebc/ndfc@3,0");
+ nodeoffset = fdt_path_offset(blob, path);
+ prop = fdt_get_property_w(blob, nodeoffset, "reg", &len);
+ if (prop == NULL) {
+ printf("Unable to update NDFC chip select for NAND booting\n");
+ return;
+ }
+ reg = (u32 *)&prop->data[0];
+ reg[0] = 0;
+ rc = fdt_find_and_setprop(blob, path, "reg", reg, 3 * sizeof(u32), 1);
+ if (rc) {
+ printf("Unable to update property NDFC mappings, err=%s\n",
+ fdt_strerror(rc));
+ return;
+ }
+}
+#endif /* CONFIG_SYS_RAMBOOT */
Code Review / kvmfornfv.git / blobdiff