--- /dev/null
+/*
+ * (C) Copyright 2005
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*----------------------------------------------------------------------------+
+ | FPGA registers and bit definitions
+ +----------------------------------------------------------------------------*/
+/*
+ * PowerPC 440EP Board FPGA is reached with physical address 0x80001FF0.
+ * TLB initialization makes it correspond to logical address 0x80001FF0.
+ * => Done init_chip.s in bootlib
+ */
+#define FPGA_BASE_ADDR 0x80002000
+
+/*----------------------------------------------------------------------------+
+ | Board Jumpers Setting Register
+ | Board Settings provided by jumpers
+ +----------------------------------------------------------------------------*/
+#define FPGA_SETTING_REG (FPGA_BASE_ADDR+0x3)
+/* Boot from small flash */
+#define FPGA_SET_REG_BOOT_SMALL_FLASH 0x80
+/* Operational Flash versus SRAM position in Memory Map */
+#define FPGA_SET_REG_OP_CODE_SRAM_SEL_MASK 0x40
+#define FPGA_SET_REG_OP_CODE_FLASH_ABOVE 0x40
+#define FPGA_SET_REG_SRAM_ABOVE 0x00
+/* Boot From NAND Flash */
+#define FPGA_SET_REG_BOOT_NAND_FLASH_MASK 0x40
+#define FPGA_SET_REG_BOOT_NAND_FLASH_SELECT 0x00
+/* On Board PCI Arbiter Select */
+#define FPGA_SET_REG_PCI_EXT_ARBITER_SEL_MASK 0x10
+#define FPGA_SET_REG_PCI_EXT_ARBITER_SEL 0x00
+
+/*----------------------------------------------------------------------------+
+ | Functions Selection Register 1
+ +----------------------------------------------------------------------------*/
+#define FPGA_SELECTION_1_REG (FPGA_BASE_ADDR+0x4)
+#define FPGA_SEL_1_REG_PHY_MASK 0xE0
+#define FPGA_SEL_1_REG_MII 0x80
+#define FPGA_SEL_1_REG_RMII 0x40
+#define FPGA_SEL_1_REG_SMII 0x20
+#define FPGA_SEL_1_REG_USB2_DEV_SEL 0x10 /* USB2 Device Selection */
+#define FPGA_SEL_1_REG_USB2_HOST_SEL 0x08 /* USB2 Host Selection */
+#define FPGA_SEL_1_REG_NF_SELEC_MASK 0x07 /* NF Selection Mask */
+#define FPGA_SEL_1_REG_NF0_SEL_BY_NFCS1 0x04 /* NF0 Selected by NF_CS1 */
+#define FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2 0x02 /* NF1 Selected by NF_CS2 */
+#define FPGA_SEL_1_REG_NF1_SEL_BY_NFCS3 0x01 /* NF1 Selected by NF_CS3 */
+
+/*----------------------------------------------------------------------------+
+ | Functions Selection Register 2
+ +----------------------------------------------------------------------------*/
+#define FPGA_SELECTION_2_REG (FPGA_BASE_ADDR+0x5)
+#define FPGA_SEL2_REG_IIC1_SCP_SEL_MASK 0x80 /* IIC1 / SCP Selection */
+#define FPGA_SEL2_REG_SEL_FRAM 0x80 /* FRAM on IIC1 bus selected - SCP Select */
+#define FPGA_SEL2_REG_SEL_SCP 0x80 /* Identical to SCP Selection */
+#define FPGA_SEL2_REG_SEL_IIC1 0x00 /* IIC1 Selection - Default Value */
+#define FPGA_SEL2_REG_SEL_DMA_A_B 0x40 /* DMA A & B channels selected */
+#define FPGA_SEL2_REG_SEL_DMA_C_D 0x20 /* DMA C & D channels selected */
+#define FPGA_SEL2_REG_DMA_EOT_TC_3_SEL 0x10 /* 0 = EOT - input to 440EP */
+ /* 1 = TC - output from 440EP */
+#define FPGA_SEL2_REG_DMA_EOT_TC_2_SEL 0x08 /* 0 = EOT (input to 440EP) */
+ /* 1 = TC (output from 440EP) */
+#define FPGA_SEL2_REG_SEL_GPIO_1 0x04 /* EBC_GPIO & USB2_GPIO selected */
+#define FPGA_SEL2_REG_SEL_GPIO_2 0x02 /* Ether._GPIO & UART_GPIO selected */
+#define FPGA_SEL2_REG_SEL_GPIO_3 0x01 /* DMA_GPIO & Trace_GPIO selected */
+
+/*----------------------------------------------------------------------------+
+ | Functions Selection Register 3
+ +----------------------------------------------------------------------------*/
+#define FPGA_SELECTION_3_REG (FPGA_BASE_ADDR+0x6)
+#define FPGA_SEL3_REG_EXP_SLOT_EN 0x80 /* Expansion Slot enabled */
+#define FPGA_SEL3_REG_SEL_UART_CONFIG_MASK 0x70
+#define FPGA_SEL3_REG_SEL_UART_CONFIG1 0x40 /* one 8_pin UART */
+#define FPGA_SEL3_REG_SEL_UART_CONFIG2 0x20 /* two 4_pin UARTs */
+#define FPGA_SEL3_REG_SEL_UART_CONFIG3 0x10 /* one 4_pin & two 2_pin UARTs */
+#define FPGA_SEL3_REG_SEL_UART_CONFIG4 0x08 /* four 2_pin UARTs */
+#define FPGA_SEL3_REG_DTR_DSR_MODE_4_PIN_UART 0x00 /* DTR/DSR mode for 4_pin_UART */
+#define FPGA_SEL3_REG_RTS_CTS_MODE_4_PIN_UART 0x04 /* RTS/CTS mode for 4_pin_UART */
+
+/*----------------------------------------------------------------------------+
+ | Soft Reset Register
+ +----------------------------------------------------------------------------*/
+#define FPGA_RESET_REG (FPGA_BASE_ADDR+0x7)
+#define FPGA_RESET_REG_RESET_USB20_DEV 0x80 /* Hard Reset of the GT3200 */
+#define FPGA_RESET_REG_RESET_DISPLAY 0x40 /* Hard Reset on Display Device */
+#define FPGA_RESET_REG_STATUS_LED_0 0x08 /* 1 = Led On */
+#define FPGA_RESET_REG_STATUS_LED_1 0x04 /* 1 = Led On */
+#define FPGA_RESET_REG_STATUS_LED_2 0x02 /* 1 = Led On */
+#define FPGA_RESET_REG_STATUS_LED_3 0x01 /* 1 = Led On */
+
+
+/*----------------------------------------------------------------------------+
+| SDR Configuration registers
++----------------------------------------------------------------------------*/
+#define SDR0_SDSTP1_EBC_ROM_BS_MASK 0x00006000 /* EBC Boot Size Mask */
+#define SDR0_SDSTP1_EBC_ROM_BS_32BIT 0x00004000 /* EBC 32 bits */
+#define SDR0_SDSTP1_EBC_ROM_BS_16BIT 0x00002000 /* EBC 16 Bits */
+#define SDR0_SDSTP1_EBC_ROM_BS_8BIT 0x00000000 /* EBC 8 Bits */
+
+#define SDR0_SDSTP1_BOOT_SEL_MASK 0x00001800 /* Boot device Selection Mask */
+#define SDR0_SDSTP1_BOOT_SEL_EBC 0x00000000 /* EBC */
+#define SDR0_SDSTP1_BOOT_SEL_PCI 0x00000800 /* PCI */
+#define SDR0_SDSTP1_BOOT_SEL_NDFC 0x00001000 /* NDFC */
+
+/* Serial Device Enabled - Addr = 0xA8 */
+#define SDR0_PSTRP0_BOOTSTRAP_IIC_A8_EN SDR0_PSTRP0_BOOTSTRAP_SETTINGS5
+/* Serial Device Enabled - Addr = 0xA4 */
+#define SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN SDR0_PSTRP0_BOOTSTRAP_SETTINGS7
+
+/* Pin Straps Reg */
+#define SDR0_PSTRP0 0x0040
+#define SDR0_PSTRP0_BOOTSTRAP_MASK 0xE0000000 /* Strap Bits */
+
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS1 0x20000000 /* Default strap settings 1 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS2 0x40000000 /* Default strap settings 2 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS3 0x60000000 /* Default strap settings 3 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS4 0x80000000 /* Default strap settings 4 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS5 0xA0000000 /* Default strap settings 5 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS6 0xC0000000 /* Default strap settings 6 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS7 0xE0000000 /* Default strap settings 7 */
+
+/*----------------------------------------------------------------------------+
+| EBC Configuration Register - EBC0_CFG
++----------------------------------------------------------------------------*/
+/* External Bus Three-State Control */
+#define EBC0_CFG_EBTC_DRIVEN 0x80000000
+/* Device-Paced Time-out Disable */
+#define EBC0_CFG_PTD_ENABLED 0x00000000
+/* Ready Timeout Count */
+#define EBC0_CFG_RTC_MASK 0x38000000
+#define EBC0_CFG_RTC_16PERCLK 0x00000000
+#define EBC0_CFG_RTC_32PERCLK 0x08000000
+#define EBC0_CFG_RTC_64PERCLK 0x10000000
+#define EBC0_CFG_RTC_128PERCLK 0x18000000
+#define EBC0_CFG_RTC_256PERCLK 0x20000000
+#define EBC0_CFG_RTC_512PERCLK 0x28000000
+#define EBC0_CFG_RTC_1024PERCLK 0x30000000
+#define EBC0_CFG_RTC_2048PERCLK 0x38000000
+/* External Master Priority Low */
+#define EBC0_CFG_EMPL_LOW 0x00000000
+#define EBC0_CFG_EMPL_MEDIUM_LOW 0x02000000
+#define EBC0_CFG_EMPL_MEDIUM_HIGH 0x04000000
+#define EBC0_CFG_EMPL_HIGH 0x06000000
+/* External Master Priority High */
+#define EBC0_CFG_EMPH_LOW 0x00000000
+#define EBC0_CFG_EMPH_MEDIUM_LOW 0x00800000
+#define EBC0_CFG_EMPH_MEDIUM_HIGH 0x01000000
+#define EBC0_CFG_EMPH_HIGH 0x01800000
+/* Chip Select Three-State Control */
+#define EBC0_CFG_CSTC_DRIVEN 0x00400000
+/* Burst Prefetch */
+#define EBC0_CFG_BPF_ONEDW 0x00000000
+#define EBC0_CFG_BPF_TWODW 0x00100000
+#define EBC0_CFG_BPF_FOURDW 0x00200000
+/* External Master Size */
+#define EBC0_CFG_EMS_8BIT 0x00000000
+/* Power Management Enable */
+#define EBC0_CFG_PME_DISABLED 0x00000000
+#define EBC0_CFG_PME_ENABLED 0x00020000
+/* Power Management Timer */
+#define EBC0_CFG_PMT_ENCODE(n) ((((unsigned long)(n))&0x1F)<<12)
+
+/*----------------------------------------------------------------------------+
+| Peripheral Bank Configuration Register - EBC0_BnCR
++----------------------------------------------------------------------------*/
+/* BAS - Base Address Select */
+#define EBC0_BNCR_BAS_ENCODE(n) ((((unsigned long)(n))&0xFFF00000)<<0)
+/* BS - Bank Size */
+#define EBC0_BNCR_BS_MASK 0x000E0000
+#define EBC0_BNCR_BS_1MB 0x00000000
+#define EBC0_BNCR_BS_2MB 0x00020000
+#define EBC0_BNCR_BS_4MB 0x00040000
+#define EBC0_BNCR_BS_8MB 0x00060000
+#define EBC0_BNCR_BS_16MB 0x00080000
+#define EBC0_BNCR_BS_32MB 0x000A0000
+#define EBC0_BNCR_BS_64MB 0x000C0000
+#define EBC0_BNCR_BS_128MB 0x000E0000
+/* BU - Bank Usage */
+#define EBC0_BNCR_BU_MASK 0x00018000
+#define EBC0_BNCR_BU_RO 0x00008000
+#define EBC0_BNCR_BU_WO 0x00010000
+#define EBC0_BNCR_BU_RW 0x00018000
+/* BW - Bus Width */
+#define EBC0_BNCR_BW_MASK 0x00006000
+#define EBC0_BNCR_BW_8BIT 0x00000000
+#define EBC0_BNCR_BW_16BIT 0x00002000
+#define EBC0_BNCR_BW_32BIT 0x00004000
+
+/*----------------------------------------------------------------------------+
+| Peripheral Bank Access Parameters - EBC0_BnAP
++----------------------------------------------------------------------------*/
+/* Burst Mode Enable */
+#define EBC0_BNAP_BME_ENABLED 0x80000000
+#define EBC0_BNAP_BME_DISABLED 0x00000000
+/* Transfert Wait */
+#define EBC0_BNAP_TWT_ENCODE(n) ((((unsigned long)(n))&0xFF)<<23) /* Bits 1:8 */
+/* Chip Select On Timing */
+#define EBC0_BNAP_CSN_ENCODE(n) ((((unsigned long)(n))&0x3)<<18) /* Bits 12:13 */
+/* Output Enable On Timing */
+#define EBC0_BNAP_OEN_ENCODE(n) ((((unsigned long)(n))&0x3)<<16) /* Bits 14:15 */
+/* Write Back Enable On Timing */
+#define EBC0_BNAP_WBN_ENCODE(n) ((((unsigned long)(n))&0x3)<<14) /* Bits 16:17 */
+/* Write Back Enable Off Timing */
+#define EBC0_BNAP_WBF_ENCODE(n) ((((unsigned long)(n))&0x3)<<12) /* Bits 18:19 */
+/* Transfert Hold */
+#define EBC0_BNAP_TH_ENCODE(n) ((((unsigned long)(n))&0x7)<<9) /* Bits 20:22 */
+/* PerReady Enable */
+#define EBC0_BNAP_RE_ENABLED 0x00000100
+#define EBC0_BNAP_RE_DISABLED 0x00000000
+/* Sample On Ready */
+#define EBC0_BNAP_SOR_DELAYED 0x00000000
+#define EBC0_BNAP_SOR_NOT_DELAYED 0x00000080
+/* Byte Enable Mode */
+#define EBC0_BNAP_BEM_WRITEONLY 0x00000000
+#define EBC0_BNAP_BEM_RW 0x00000040
+/* Parity Enable */
+#define EBC0_BNAP_PEN_DISABLED 0x00000000
+#define EBC0_BNAP_PEN_ENABLED 0x00000020
+
+/*----------------------------------------------------------------------------+
+| Define Boot devices
++----------------------------------------------------------------------------*/
+/* */
+#define BOOT_FROM_SMALL_FLASH 0x00
+#define BOOT_FROM_LARGE_FLASH_OR_SRAM 0x01
+#define BOOT_FROM_NAND_FLASH0 0x02
+#define BOOT_FROM_PCI 0x03
+#define BOOT_DEVICE_UNKNOWN 0x04
+
+
+#define PVR_POWERPC_440EP_PASS1 0x42221850
+#define PVR_POWERPC_440EP_PASS2 0x422218D3
+
+#define GPIO0 0
+#define GPIO1 1
+
+/*#define MAX_SELECTION_NB CORE_NB */
+#define MAX_CORE_SELECT_NB 22
+
+/*----------------------------------------------------------------------------+
+ | PPC440EP GPIOs addresses.
+ +----------------------------------------------------------------------------*/
+#define GPIO0_REAL 0xEF600B00
+
+#define GPIO1_REAL 0xEF600C00
+
+/* Offsets */
+#define GPIOx_OR 0x00 /* GPIO Output Register */
+#define GPIOx_TCR 0x04 /* GPIO Three-State Control Register */
+#define GPIOx_OSL 0x08 /* GPIO Output Select Register (Bits 0-31) */
+#define GPIOx_OSH 0x0C /* GPIO Ouput Select Register (Bits 32-63) */
+#define GPIOx_TSL 0x10 /* GPIO Three-State Select Register (Bits 0-31) */
+#define GPIOx_TSH 0x14 /* GPIO Three-State Select Register (Bits 32-63) */
+#define GPIOx_ODR 0x18 /* GPIO Open drain Register */
+#define GPIOx_IR 0x1C /* GPIO Input Register */
+#define GPIOx_RR1 0x20 /* GPIO Receive Register 1 */
+#define GPIOx_RR2 0x24 /* GPIO Receive Register 2 */
+#define GPIOx_RR3 0x28 /* GPIO Receive Register 3 */
+#define GPIOx_IS1L 0x30 /* GPIO Input Select Register 1 (Bits 0-31) */
+#define GPIOx_IS1H 0x34 /* GPIO Input Select Register 1 (Bits 32-63) */
+#define GPIOx_IS2L 0x38 /* GPIO Input Select Register 2 (Bits 0-31) */
+#define GPIOx_IS2H 0x3C /* GPIO Input Select Register 2 (Bits 32-63) */
+#define GPIOx_IS3L 0x40 /* GPIO Input Select Register 3 (Bits 0-31) */
+#define GPIOx_IS3H 0x44 /* GPIO Input Select Register 3 (Bits 32-63) */
+
+/* GPIO0 */
+#define GPIO0_IS1L (GPIO0_BASE+GPIOx_IS1L)
+#define GPIO0_IS1H (GPIO0_BASE+GPIOx_IS1H)
+#define GPIO0_IS2L (GPIO0_BASE+GPIOx_IS2L)
+#define GPIO0_IS2H (GPIO0_BASE+GPIOx_IS2H)
+#define GPIO0_IS3L (GPIO0_BASE+GPIOx_IS3L)
+#define GPIO0_IS3H (GPIO0_BASE+GPIOx_IS3L)
+
+/* GPIO1 */
+#define GPIO1_IS1L (GPIO1_BASE+GPIOx_IS1L)
+#define GPIO1_IS1H (GPIO1_BASE+GPIOx_IS1H)
+#define GPIO1_IS2L (GPIO1_BASE+GPIOx_IS2L)
+#define GPIO1_IS2H (GPIO1_BASE+GPIOx_IS2H)
+#define GPIO1_IS3L (GPIO1_BASE+GPIOx_IS3L)
+#define GPIO1_IS3H (GPIO1_BASE+GPIOx_IS3L)
+
+#define GPIO_OS(x) (x+GPIOx_OSL) /* GPIO Output Register High or Low */
+#define GPIO_TS(x) (x+GPIOx_TSL) /* GPIO Three-state Control Reg High or Low */
+#define GPIO_IS1(x) (x+GPIOx_IS1L) /* GPIO Input register1 High or Low */
+#define GPIO_IS2(x) (x+GPIOx_IS2L) /* GPIO Input register2 High or Low */
+#define GPIO_IS3(x) (x+GPIOx_IS3L) /* GPIO Input register3 High or Low */
+
+
+/*----------------------------------------------------------------------------+
+ | XX XX
+ |
+ | XXXXXX XXX XX XXX XXX
+ | XX XX X XX XX XX
+ | XX XX X XX XX XX
+ | XX XX XX XX XX
+ | XXXXXX XXX XXX XXXX XXXX
+ +----------------------------------------------------------------------------*/
+/*----------------------------------------------------------------------------+
+ | Defines
+ +----------------------------------------------------------------------------*/
+typedef enum zmii_config { ZMII_CONFIGURATION_UNKNOWN,
+ ZMII_CONFIGURATION_IS_MII,
+ ZMII_CONFIGURATION_IS_RMII,
+ ZMII_CONFIGURATION_IS_SMII
+} zmii_config_t;
+
+/*----------------------------------------------------------------------------+
+ | Declare Configuration values
+ +----------------------------------------------------------------------------*/
+typedef enum uart_config_nb { L1, L2, L3, L4 } uart_config_nb_t;
+typedef enum core_selection { CORE_NOT_SELECTED, CORE_SELECTED} core_selection_t;
+typedef enum config_list { IIC_CORE,
+ SCP_CORE,
+ DMA_CHANNEL_AB,
+ UIC_4_9,
+ USB2_HOST,
+ DMA_CHANNEL_CD,
+ USB2_DEVICE,
+ PACKET_REJ_FUNC_AVAIL,
+ USB1_DEVICE,
+ EBC_MASTER,
+ NAND_FLASH,
+ UART_CORE0,
+ UART_CORE1,
+ UART_CORE2,
+ UART_CORE3,
+ MII_SEL,
+ RMII_SEL,
+ SMII_SEL,
+ PACKET_REJ_FUNC_EN,
+ UIC_0_3,
+ USB1_HOST,
+ PCI_PATCH,
+ CORE_NB
+} core_list_t;
+
+typedef enum block3_value { B3_V1, B3_V2, B3_V3, B3_V4, B3_V5,
+ B3_V6, B3_V7, B3_V8, B3_V9, B3_V10,
+ B3_V11, B3_V12, B3_V13, B3_V14, B3_V15,
+ B3_V16, B3_VALUE_UNKNOWN
+} block3_value_t;
+
+typedef enum config_validity { CONFIG_IS_VALID,
+ CONFIG_IS_INVALID
+} config_validity_t;
Code Review / kvmfornfv.git / blobdiff