--- /dev/null
+/*
+ * (C) Copyright 2001-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc8xx.h>
+
+/* ------------------------------------------------------------------------- */
+
+static long int dram_size (long int, long int *, long int);
+
+/* ------------------------------------------------------------------------- */
+
+#define _NOT_USED_ 0xFFFFFFFF
+
+const uint sdram_table[] =
+{
+ /*
+ * Single Read. (Offset 0 in UPMA RAM)
+ */
+ 0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
+ 0x1FF77C47, /* last */
+ /*
+ * SDRAM Initialization (offset 5 in UPMA RAM)
+ *
+ * This is no UPM entry point. The following definition uses
+ * the remaining space to establish an initialization
+ * sequence, which is executed by a RUN command.
+ *
+ */
+ 0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
+ /*
+ * Burst Read. (Offset 8 in UPMA RAM)
+ */
+ 0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
+ 0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Single Write. (Offset 18 in UPMA RAM)
+ */
+ 0x1F07FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Burst Write. (Offset 20 in UPMA RAM)
+ */
+ 0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
+ 0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
+ _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Refresh (Offset 30 in UPMA RAM)
+ */
+ 0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+ 0xFFFFFC84, 0xFFFFFC07, /* last */
+ _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Exception. (Offset 3c in UPMA RAM)
+ */
+ 0x7FFFFC07, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_,
+};
+
+/* ------------------------------------------------------------------------- */
+
+
+/*
+ * Check Board Identity:
+ *
+ * Always return 1 (no second DRAM bank).
+ */
+
+int checkboard (void)
+{
+ char buf[64];
+ int i;
+ int l = getenv_f("serial#", buf, sizeof(buf));
+
+ puts ("Board: RRvision ");
+
+ for (i=0; i < l; ++i) {
+ if (buf[i] == ' ')
+ break;
+ putc (buf[i]);
+ }
+
+ putc ('\n');
+
+ return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+phys_size_t initdram (int board_type)
+{
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+ volatile memctl8xx_t *memctl = &immap->im_memctl;
+ unsigned long reg;
+ long int size8, size9;
+ long int size = 0;
+
+ upmconfig (UPMA, (uint *)sdram_table, sizeof(sdram_table) / sizeof(uint));
+
+ /*
+ * Preliminary prescaler for refresh (depends on number of
+ * banks): This value is selected for four cycles every 62.4 us
+ * with two SDRAM banks or four cycles every 31.2 us with one
+ * bank. It will be adjusted after memory sizing.
+ */
+ memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
+
+ memctl->memc_mar = 0x00000088;
+
+ /*
+ * Map controller bank 1 the SDRAM bank 2 at physical address 0.
+ */
+ memctl->memc_or1 = CONFIG_SYS_OR2_PRELIM;
+ memctl->memc_br1 = CONFIG_SYS_BR2_PRELIM;
+
+ memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
+
+ udelay (200);
+
+ /* perform SDRAM initializsation sequence */
+
+ memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
+ udelay (1);
+ memctl->memc_mcr = 0x80002230; /* SDRAM bank 0 - execute twice */
+ udelay (1);
+
+ memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
+
+ udelay (1000);
+
+ /*
+ * Check Bank 0 Memory Size
+ *
+ * try 8 column mode
+ */
+ size8 = dram_size (CONFIG_SYS_MAMR_8COL,
+ SDRAM_BASE2_PRELIM,
+ SDRAM_MAX_SIZE);
+
+ udelay (1000);
+
+ /*
+ * try 9 column mode
+ */
+ size9 = dram_size (CONFIG_SYS_MAMR_9COL,
+ SDRAM_BASE2_PRELIM,
+ SDRAM_MAX_SIZE);
+
+ if (size8 < size9) { /* leave configuration at 9 columns */
+ size = size9;
+/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
+ } else { /* back to 8 columns */
+ size = size8;
+ memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
+ udelay (500);
+/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
+ }
+
+ udelay (1000);
+
+ /*
+ * Adjust refresh rate depending on SDRAM type
+ * For types > 128 MBit leave it at the current (fast) rate
+ */
+ if (size < 0x02000000) {
+ /* reduce to 15.6 us (62.4 us / quad) */
+ memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
+ udelay (1000);
+ }
+
+ /*
+ * Final mapping
+ */
+ memctl->memc_or1 = ((-size) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
+ memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
+
+ /*
+ * No bank 1
+ *
+ * invalidate bank
+ */
+ memctl->memc_br3 = 0;
+
+ /* adjust refresh rate depending on SDRAM type, one bank */
+ reg = memctl->memc_mptpr;
+ reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
+ memctl->memc_mptpr = reg;
+
+ udelay (10000);
+
+ return (size);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+
+static long int dram_size (long int mamr_value, long int *base,
+ long int maxsize)
+{
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+ volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+ memctl->memc_mamr = mamr_value;
+
+ return (get_ram_size(base, maxsize));
+}
Code Review / kvmfornfv.git / blobdiff