Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / board / LaCie / netspace_v2 / netspace_v2.c

diff --git a/qemu/roms/u-boot/board/LaCie/netspace_v2/netspace_v2.c b/qemu/roms/u-boot/board/LaCie/netspace_v2/netspace_v2.c
new file mode 100644 (file)
index 0000000..3773587
--- /dev/null
+++ b/qemu/roms/u-boot/board/LaCie/netspace_v2/netspace_v2.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * Based on Kirkwood support:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/gpio.h>
+
+#include "netspace_v2.h"
+#include "../common/common.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+       /* Gpio configuration */
+       kw_config_gpio(NETSPACE_V2_OE_VAL_LOW, NETSPACE_V2_OE_VAL_HIGH,
+                       NETSPACE_V2_OE_LOW, NETSPACE_V2_OE_HIGH);
+
+       /* Multi-Purpose Pins Functionality configuration */
+       static const u32 kwmpp_config[] = {
+               MPP0_SPI_SCn,
+               MPP1_SPI_MOSI,
+               MPP2_SPI_SCK,
+               MPP3_SPI_MISO,
+               MPP4_NF_IO6,
+               MPP5_NF_IO7,
+               MPP6_SYSRST_OUTn,
+               MPP7_GPO,               /* Fan speed (bit 1) */
+               MPP8_TW_SDA,
+               MPP9_TW_SCK,
+               MPP10_UART0_TXD,
+               MPP11_UART0_RXD,
+               MPP12_GPO,              /* Red led */
+               MPP14_GPIO,             /* USB fuse */
+               MPP16_GPIO,             /* SATA 0 power */
+               MPP17_GPIO,             /* SATA 1 power */
+               MPP18_NF_IO0,
+               MPP19_NF_IO1,
+               MPP20_SATA1_ACTn,
+               MPP21_SATA0_ACTn,
+               MPP22_GPIO,             /* Fan speed (bit 0) */
+               MPP23_GPIO,             /* Fan power */
+               MPP24_GPIO,             /* USB mode select */
+               MPP25_GPIO,             /* Fan rotation fail */
+               MPP26_GPIO,             /* USB vbus-in detection */
+               MPP28_GPIO,             /* USB enable vbus-out */
+               MPP29_GPIO,             /* Blue led (slow register) */
+               MPP30_GPIO,             /* Blue led (command register) */
+               MPP31_GPIO,             /* Board power off */
+               MPP32_GPIO,             /* Button (0 = Released, 1 = Pushed) */
+               MPP33_GPIO,             /* Fan speed (bit 2) */
+               0
+       };
+       kirkwood_mpp_conf(kwmpp_config, NULL);
+
+       return 0;
+}
+
+int board_init(void)
+{
+       /* Machine number */
+       gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
+
+       /* Boot parameters address */
+       gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+       return 0;
+}
+
+#if defined(CONFIG_MISC_INIT_R)
+int misc_init_r(void)
+{
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
+       if (!getenv("ethaddr")) {
+               uchar mac[6];
+               if (lacie_read_mac_address(mac) == 0)
+                       eth_setenv_enetaddr("ethaddr", mac);
+       }
+#endif
+       return 0;
+}
+#endif
+
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
+/* Configure and initialize PHY */
+void reset_phy(void)
+{
+#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
+       mv_phy_88e1318_init("egiga0", 0);
+#else
+       mv_phy_88e1116_init("egiga0", 8);
+#endif
+}
+#endif
+
+#if defined(CONFIG_KIRKWOOD_GPIO)
+/* Return GPIO button status */
+static int
+do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+       return kw_gpio_get_value(NETSPACE_V2_GPIO_BUTTON);
+}
+
+U_BOOT_CMD(button, 1, 1, do_read_button,
+          "Return GPIO button status 0=off 1=on", "");
+#endif