--- /dev/null
+/*
+ * common.c
+ *
+ * common board functions for B&R boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <power/tps65217.h>
+#include "bur_common.h"
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+/* --------------------------------------------------------------------------*/
+void blink(u32 blinks, u32 intervall, u32 pin)
+{
+ gpio_direction_output(pin, 0);
+ int val = 0;
+
+ do {
+ val ^= 0x01;
+ gpio_set_value(pin, val);
+ mdelay(intervall);
+ } while (blinks--);
+
+ gpio_set_value(pin, 0);
+}
+#ifdef CONFIG_SPL_BUILD
+void pmicsetup(u32 mpupll)
+{
+ int mpu_vdd;
+ int usb_cur_lim;
+
+ /* setup I2C */
+ enable_i2c0_pin_mux();
+ i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+ if (i2c_probe(TPS65217_CHIP_PM)) {
+ puts("PMIC (0x24) not found! skip further initalization.\n");
+ return;
+ }
+
+ /* Get the frequency which is defined by device fuses */
+ dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+ printf("detected max. frequency: %d - ", dpll_mpu_opp100.m);
+
+ if (0 != mpupll) {
+ dpll_mpu_opp100.m = MPUPLL_M_1000;
+ printf("retuning MPU-PLL to: %d MHz.\n", dpll_mpu_opp100.m);
+ } else {
+ puts("ok.\n");
+ }
+ /*
+ * Increase USB current limit to 1300mA or 1800mA and set
+ * the MPU voltage controller as needed.
+ */
+ if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
+ usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
+ mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
+ } else {
+ usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
+ mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
+ }
+
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
+ usb_cur_lim, TPS65217_USB_INPUT_CUR_LIMIT_MASK))
+ puts("tps65217_reg_write failure\n");
+
+ /* Set DCDC3 (CORE) voltage to 1.125V */
+ if (tps65217_voltage_update(TPS65217_DEFDCDC3,
+ TPS65217_DCDC_VOLT_SEL_1125MV)) {
+ puts("tps65217_voltage_update failure\n");
+ return;
+ }
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+ /* Set DCDC2 (MPU) voltage */
+ if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
+ puts("tps65217_voltage_update failure\n");
+ return;
+ }
+
+ /* Set LDO3 to 1.8V */
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+ TPS65217_DEFLS1,
+ TPS65217_LDO_VOLTAGE_OUT_1_8,
+ TPS65217_LDO_MASK))
+ puts("tps65217_reg_write failure\n");
+ /* Set LDO4 to 3.3V */
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+ TPS65217_DEFLS2,
+ TPS65217_LDO_VOLTAGE_OUT_3_3,
+ TPS65217_LDO_MASK))
+ puts("tps65217_reg_write failure\n");
+
+ /* Set MPU Frequency to what we detected now that voltages are set */
+ do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+void set_uart_mux_conf(void)
+{
+ enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+ enable_board_pin_mux();
+}
+
+#endif /* CONFIG_SPL_BUILD */
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+ return;
+}
+
+/* describing port offsets of TI's CPSW block */
+static struct cpsw_slave_data cpsw_slaves[] = {
+ {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_addr = 1,
+ },
+ {
+ .slave_reg_ofs = 0x308,
+ .sliver_reg_ofs = 0xdc0,
+ .phy_addr = 2,
+ },
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = CPSW_MDIO_BASE,
+ .cpsw_base = CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = cpsw_slaves,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .bd_ram_ofs = 0x2000,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+#endif /* CONFIG_DRIVER_TI_CPSW, ... */
+
+#if defined(CONFIG_DRIVER_TI_CPSW)
+
+int board_eth_init(bd_t *bis)
+{
+ int rv = 0;
+ uint8_t mac_addr[6];
+ uint32_t mac_hi, mac_lo;
+
+ /* try reading mac address from efuse */
+ mac_lo = readl(&cdev->macid0l);
+ mac_hi = readl(&cdev->macid0h);
+ mac_addr[0] = mac_hi & 0xFF;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+ mac_addr[4] = mac_lo & 0xFF;
+ mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+ if (!getenv("ethaddr")) {
+ printf("<ethaddr> not set. Validating first E-fuse MAC ... ");
+
+ if (is_valid_ether_addr(mac_addr)) {
+ printf("using: %02X:%02X:%02X:%02X:%02X:%02X.\n",
+ mac_addr[0], mac_addr[1], mac_addr[2],
+ mac_addr[3], mac_addr[4], mac_addr[5]
+ );
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+ }
+ }
+ writel(MII_MODE_ENABLE, &cdev->miisel);
+ cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
+ cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII;
+
+ rv = cpsw_register(&cpsw_data);
+ if (rv < 0) {
+ printf("Error %d registering CPSW switch\n", rv);
+ return 0;
+ }
+#endif /* CONFIG_DRIVER_TI_CPSW, ... */
+ return rv;
+}
+#endif /* CONFIG_DRIVER_TI_CPSW */
Code Review / kvmfornfv.git / blobdiff