--- /dev/null
+/*
+ * MPC8560 FCC Fast Ethernet
+ * Copyright (c) 2003 Motorola,Inc.
+ * Xianghua Xiao, (X.Xiao@motorola.com)
+ *
+ * Copyright (c) 2000 MontaVista Software, Inc. Dan Malek (dmalek@jlc.net)
+ *
+ * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * MPC8560 FCC Fast Ethernet
+ * Basic ET HW initialization and packet RX/TX routines
+ *
+ * This code will not perform the IO port configuration. This should be
+ * done in the iop_conf_t structure specific for the board.
+ *
+ * TODO:
+ * add a PHY driver to do the negotiation
+ * reflect negotiation results in FPSMR
+ * look for ways to configure the board specific stuff elsewhere, eg.
+ * config_xxx.h or the board directory
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <asm/cpm_85xx.h>
+#include <command.h>
+#include <config.h>
+#include <net.h>
+
+#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
+#include <miiphy.h>
+#endif
+
+#if defined(CONFIG_ETHER_ON_FCC) && defined(CONFIG_CMD_NET)
+
+static struct ether_fcc_info_s
+{
+ int ether_index;
+ int proff_enet;
+ ulong cpm_cr_enet_sblock;
+ ulong cpm_cr_enet_page;
+ ulong cmxfcr_mask;
+ ulong cmxfcr_value;
+}
+ ether_fcc_info[] =
+{
+#ifdef CONFIG_ETHER_ON_FCC1
+{
+ 0,
+ PROFF_FCC1,
+ CPM_CR_FCC1_SBLOCK,
+ CPM_CR_FCC1_PAGE,
+ CONFIG_SYS_CMXFCR_MASK1,
+ CONFIG_SYS_CMXFCR_VALUE1
+},
+#endif
+
+#ifdef CONFIG_ETHER_ON_FCC2
+{
+ 1,
+ PROFF_FCC2,
+ CPM_CR_FCC2_SBLOCK,
+ CPM_CR_FCC2_PAGE,
+ CONFIG_SYS_CMXFCR_MASK2,
+ CONFIG_SYS_CMXFCR_VALUE2
+},
+#endif
+
+#ifdef CONFIG_ETHER_ON_FCC3
+{
+ 2,
+ PROFF_FCC3,
+ CPM_CR_FCC3_SBLOCK,
+ CPM_CR_FCC3_PAGE,
+ CONFIG_SYS_CMXFCR_MASK3,
+ CONFIG_SYS_CMXFCR_VALUE3
+},
+#endif
+};
+
+/*---------------------------------------------------------------------*/
+
+/* Maximum input DMA size. Must be a should(?) be a multiple of 4. */
+#define PKT_MAXDMA_SIZE 1520
+
+/* The FCC stores dest/src/type, data, and checksum for receive packets. */
+#define PKT_MAXBUF_SIZE 1518
+#define PKT_MINBUF_SIZE 64
+
+/* Maximum input buffer size. Must be a multiple of 32. */
+#define PKT_MAXBLR_SIZE 1536
+
+#define TOUT_LOOP 1000000
+
+#define TX_BUF_CNT 2
+
+static uint rxIdx; /* index of the current RX buffer */
+static uint txIdx; /* index of the current TX buffer */
+
+/*
+ * FCC Ethernet Tx and Rx buffer descriptors.
+ * Provide for Double Buffering
+ * Note: PKTBUFSRX is defined in net.h
+ */
+
+typedef volatile struct rtxbd {
+ cbd_t rxbd[PKTBUFSRX];
+ cbd_t txbd[TX_BUF_CNT];
+} RTXBD;
+
+/* Good news: the FCC supports external BDs! */
+#ifdef __GNUC__
+static RTXBD rtx __attribute__ ((aligned(8)));
+#else
+#error "rtx must be 64-bit aligned"
+#endif
+
+#undef ET_DEBUG
+
+static int fec_send(struct eth_device *dev, void *packet, int length)
+{
+ int i = 0;
+ int result = 0;
+
+ if (length <= 0) {
+ printf("fec: bad packet size: %d\n", length);
+ goto out;
+ }
+
+ for(i=0; rtx.txbd[txIdx].cbd_sc & BD_ENET_TX_READY; i++) {
+ if (i >= TOUT_LOOP) {
+ printf("fec: tx buffer not ready\n");
+ goto out;
+ }
+ }
+
+ rtx.txbd[txIdx].cbd_bufaddr = (uint)packet;
+ rtx.txbd[txIdx].cbd_datlen = length;
+ rtx.txbd[txIdx].cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_LAST | \
+ BD_ENET_TX_TC | BD_ENET_TX_PAD);
+
+ for(i=0; rtx.txbd[txIdx].cbd_sc & BD_ENET_TX_READY; i++) {
+ if (i >= TOUT_LOOP) {
+ printf("fec: tx error\n");
+ goto out;
+ }
+ }
+
+#ifdef ET_DEBUG
+ printf("cycles: 0x%x txIdx=0x%04x status: 0x%04x\n", i, txIdx,rtx.txbd[txIdx].cbd_sc);
+ printf("packets at 0x%08x, length_in_bytes=0x%x\n",(uint)packet,length);
+ for(i=0;i<(length/16 + 1);i++) {
+ printf("%08x %08x %08x %08x\n",*((uint *)rtx.txbd[txIdx].cbd_bufaddr+i*4),\
+ *((uint *)rtx.txbd[txIdx].cbd_bufaddr + i*4 + 1),*((uint *)rtx.txbd[txIdx].cbd_bufaddr + i*4 + 2), \
+ *((uint *)rtx.txbd[txIdx].cbd_bufaddr + i*4 + 3));
+ }
+#endif
+
+ /* return only status bits */
+ result = rtx.txbd[txIdx].cbd_sc & BD_ENET_TX_STATS;
+ txIdx = (txIdx + 1) % TX_BUF_CNT;
+
+out:
+ return result;
+}
+
+static int fec_recv(struct eth_device* dev)
+{
+ int length;
+
+ for (;;)
+ {
+ if (rtx.rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
+ length = -1;
+ break; /* nothing received - leave for() loop */
+ }
+ length = rtx.rxbd[rxIdx].cbd_datlen;
+
+ if (rtx.rxbd[rxIdx].cbd_sc & 0x003f) {
+ printf("fec: rx error %04x\n", rtx.rxbd[rxIdx].cbd_sc);
+ }
+ else {
+ /* Pass the packet up to the protocol layers. */
+ NetReceive(NetRxPackets[rxIdx], length - 4);
+ }
+
+
+ /* Give the buffer back to the FCC. */
+ rtx.rxbd[rxIdx].cbd_datlen = 0;
+
+ /* wrap around buffer index when necessary */
+ if ((rxIdx + 1) >= PKTBUFSRX) {
+ rtx.rxbd[PKTBUFSRX - 1].cbd_sc = (BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
+ rxIdx = 0;
+ }
+ else {
+ rtx.rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
+ rxIdx++;
+ }
+ }
+ return length;
+}
+
+
+static int fec_init(struct eth_device* dev, bd_t *bis)
+{
+ struct ether_fcc_info_s * info = dev->priv;
+ int i;
+ volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR;
+ volatile ccsr_cpm_cp_t *cp = &(cpm->im_cpm_cp);
+ fcc_enet_t *pram_ptr;
+ unsigned long mem_addr;
+
+#if 0
+ mii_discover_phy();
+#endif
+
+ /* 28.9 - (1-2): ioports have been set up already */
+
+ /* 28.9 - (3): connect FCC's tx and rx clocks */
+ cpm->im_cpm_mux.cmxuar = 0; /* ATM */
+ cpm->im_cpm_mux.cmxfcr = (cpm->im_cpm_mux.cmxfcr & ~info->cmxfcr_mask) |
+ info->cmxfcr_value;
+
+ /* 28.9 - (4): GFMR: disable tx/rx, CCITT CRC, set Mode Ethernet */
+ if(info->ether_index == 0) {
+ cpm->im_cpm_fcc1.gfmr = FCC_GFMR_MODE_ENET | FCC_GFMR_TCRC_32;
+ } else if (info->ether_index == 1) {
+ cpm->im_cpm_fcc2.gfmr = FCC_GFMR_MODE_ENET | FCC_GFMR_TCRC_32;
+ } else if (info->ether_index == 2) {
+ cpm->im_cpm_fcc3.gfmr = FCC_GFMR_MODE_ENET | FCC_GFMR_TCRC_32;
+ }
+
+ /* 28.9 - (5): FPSMR: enable full duplex, select CCITT CRC for Ethernet,MII */
+ if(info->ether_index == 0) {
+ cpm->im_cpm_fcc1.fpsmr = CONFIG_SYS_FCC_PSMR | FCC_PSMR_ENCRC;
+ } else if (info->ether_index == 1){
+ cpm->im_cpm_fcc2.fpsmr = CONFIG_SYS_FCC_PSMR | FCC_PSMR_ENCRC;
+ } else if (info->ether_index == 2){
+ cpm->im_cpm_fcc3.fpsmr = CONFIG_SYS_FCC_PSMR | FCC_PSMR_ENCRC;
+ }
+
+ /* 28.9 - (6): FDSR: Ethernet Syn */
+ if(info->ether_index == 0) {
+ cpm->im_cpm_fcc1.fdsr = 0xD555;
+ } else if (info->ether_index == 1) {
+ cpm->im_cpm_fcc2.fdsr = 0xD555;
+ } else if (info->ether_index == 2) {
+ cpm->im_cpm_fcc3.fdsr = 0xD555;
+ }
+
+ /* reset indeces to current rx/tx bd (see eth_send()/eth_rx()) */
+ rxIdx = 0;
+ txIdx = 0;
+
+ /* Setup Receiver Buffer Descriptors */
+ for (i = 0; i < PKTBUFSRX; i++)
+ {
+ rtx.rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
+ rtx.rxbd[i].cbd_datlen = 0;
+ rtx.rxbd[i].cbd_bufaddr = (uint)NetRxPackets[i];
+ }
+ rtx.rxbd[PKTBUFSRX - 1].cbd_sc |= BD_ENET_RX_WRAP;
+
+ /* Setup Ethernet Transmitter Buffer Descriptors */
+ for (i = 0; i < TX_BUF_CNT; i++)
+ {
+ rtx.txbd[i].cbd_sc = 0;
+ rtx.txbd[i].cbd_datlen = 0;
+ rtx.txbd[i].cbd_bufaddr = 0;
+ }
+ rtx.txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;
+
+ /* 28.9 - (7): initialize parameter ram */
+ pram_ptr = (fcc_enet_t *)&(cpm->im_dprambase[info->proff_enet]);
+
+ /* clear whole structure to make sure all reserved fields are zero */
+ memset((void*)pram_ptr, 0, sizeof(fcc_enet_t));
+
+ /*
+ * common Parameter RAM area
+ *
+ * Allocate space in the reserved FCC area of DPRAM for the
+ * internal buffers. No one uses this space (yet), so we
+ * can do this. Later, we will add resource management for
+ * this area.
+ * CPM_FCC_SPECIAL_BASE: 0xB000 for MPC8540, MPC8560
+ * 0x9000 for MPC8541, MPC8555
+ */
+ mem_addr = CPM_FCC_SPECIAL_BASE + ((info->ether_index) * 64);
+ pram_ptr->fen_genfcc.fcc_riptr = mem_addr;
+ pram_ptr->fen_genfcc.fcc_tiptr = mem_addr+32;
+ /*
+ * Set maximum bytes per receive buffer.
+ * It must be a multiple of 32.
+ */
+ pram_ptr->fen_genfcc.fcc_mrblr = PKT_MAXBLR_SIZE; /* 1536 */
+ /* localbus SDRAM should be preferred */
+ pram_ptr->fen_genfcc.fcc_rstate = (CPMFCR_GBL | CPMFCR_EB |
+ CONFIG_SYS_CPMFCR_RAMTYPE) << 24;
+ pram_ptr->fen_genfcc.fcc_rbase = (unsigned int)(&rtx.rxbd[rxIdx]);
+ pram_ptr->fen_genfcc.fcc_rbdstat = 0;
+ pram_ptr->fen_genfcc.fcc_rbdlen = 0;
+ pram_ptr->fen_genfcc.fcc_rdptr = 0;
+ /* localbus SDRAM should be preferred */
+ pram_ptr->fen_genfcc.fcc_tstate = (CPMFCR_GBL | CPMFCR_EB |
+ CONFIG_SYS_CPMFCR_RAMTYPE) << 24;
+ pram_ptr->fen_genfcc.fcc_tbase = (unsigned int)(&rtx.txbd[txIdx]);
+ pram_ptr->fen_genfcc.fcc_tbdstat = 0;
+ pram_ptr->fen_genfcc.fcc_tbdlen = 0;
+ pram_ptr->fen_genfcc.fcc_tdptr = 0;
+
+ /* protocol-specific area */
+ pram_ptr->fen_statbuf = 0x0;
+ pram_ptr->fen_cmask = 0xdebb20e3; /* CRC mask */
+ pram_ptr->fen_cpres = 0xffffffff; /* CRC preset */
+ pram_ptr->fen_crcec = 0;
+ pram_ptr->fen_alec = 0;
+ pram_ptr->fen_disfc = 0;
+ pram_ptr->fen_retlim = 15; /* Retry limit threshold */
+ pram_ptr->fen_retcnt = 0;
+ pram_ptr->fen_pper = 0;
+ pram_ptr->fen_boffcnt = 0;
+ pram_ptr->fen_gaddrh = 0;
+ pram_ptr->fen_gaddrl = 0;
+ pram_ptr->fen_mflr = PKT_MAXBUF_SIZE; /* maximum frame length register */
+ /*
+ * Set Ethernet station address.
+ *
+ * This is supplied in the board information structure, so we
+ * copy that into the controller.
+ * So far we have only been given one Ethernet address. We make
+ * it unique by setting a few bits in the upper byte of the
+ * non-static part of the address.
+ */
+#define ea eth_get_dev()->enetaddr
+ pram_ptr->fen_paddrh = (ea[5] << 8) + ea[4];
+ pram_ptr->fen_paddrm = (ea[3] << 8) + ea[2];
+ pram_ptr->fen_paddrl = (ea[1] << 8) + ea[0];
+#undef ea
+ pram_ptr->fen_ibdcount = 0;
+ pram_ptr->fen_ibdstart = 0;
+ pram_ptr->fen_ibdend = 0;
+ pram_ptr->fen_txlen = 0;
+ pram_ptr->fen_iaddrh = 0; /* disable hash */
+ pram_ptr->fen_iaddrl = 0;
+ pram_ptr->fen_minflr = PKT_MINBUF_SIZE; /* minimum frame length register: 64 */
+ /* pad pointer. use tiptr since we don't need a specific padding char */
+ pram_ptr->fen_padptr = pram_ptr->fen_genfcc.fcc_tiptr;
+ pram_ptr->fen_maxd1 = PKT_MAXDMA_SIZE; /* maximum DMA1 length:1520 */
+ pram_ptr->fen_maxd2 = PKT_MAXDMA_SIZE; /* maximum DMA2 length:1520 */
+
+#if defined(ET_DEBUG)
+ printf("parm_ptr(0xff788500) = %p\n",pram_ptr);
+ printf("pram_ptr->fen_genfcc.fcc_rbase %08x\n",
+ pram_ptr->fen_genfcc.fcc_rbase);
+ printf("pram_ptr->fen_genfcc.fcc_tbase %08x\n",
+ pram_ptr->fen_genfcc.fcc_tbase);
+#endif
+
+ /* 28.9 - (8)(9): clear out events in FCCE */
+ /* 28.9 - (9): FCCM: mask all events */
+ if(info->ether_index == 0) {
+ cpm->im_cpm_fcc1.fcce = ~0x0;
+ cpm->im_cpm_fcc1.fccm = 0;
+ } else if (info->ether_index == 1) {
+ cpm->im_cpm_fcc2.fcce = ~0x0;
+ cpm->im_cpm_fcc2.fccm = 0;
+ } else if (info->ether_index == 2) {
+ cpm->im_cpm_fcc3.fcce = ~0x0;
+ cpm->im_cpm_fcc3.fccm = 0;
+ }
+
+ /* 28.9 - (10-12): we don't use ethernet interrupts */
+
+ /* 28.9 - (13)
+ *
+ * Let's re-initialize the channel now. We have to do it later
+ * than the manual describes because we have just now finished
+ * the BD initialization.
+ */
+ cp->cpcr = mk_cr_cmd(info->cpm_cr_enet_page,
+ info->cpm_cr_enet_sblock,
+ 0x0c,
+ CPM_CR_INIT_TRX) | CPM_CR_FLG;
+ do {
+ __asm__ __volatile__ ("eieio");
+ } while (cp->cpcr & CPM_CR_FLG);
+
+ /* 28.9 - (14): enable tx/rx in gfmr */
+ if(info->ether_index == 0) {
+ cpm->im_cpm_fcc1.gfmr |= FCC_GFMR_ENT | FCC_GFMR_ENR;
+ } else if (info->ether_index == 1) {
+ cpm->im_cpm_fcc2.gfmr |= FCC_GFMR_ENT | FCC_GFMR_ENR;
+ } else if (info->ether_index == 2) {
+ cpm->im_cpm_fcc3.gfmr |= FCC_GFMR_ENT | FCC_GFMR_ENR;
+ }
+
+ return 1;
+}
+
+static void fec_halt(struct eth_device* dev)
+{
+ struct ether_fcc_info_s * info = dev->priv;
+ volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR;
+
+ /* write GFMR: disable tx/rx */
+ if(info->ether_index == 0) {
+ cpm->im_cpm_fcc1.gfmr &= ~(FCC_GFMR_ENT | FCC_GFMR_ENR);
+ } else if(info->ether_index == 1) {
+ cpm->im_cpm_fcc2.gfmr &= ~(FCC_GFMR_ENT | FCC_GFMR_ENR);
+ } else if(info->ether_index == 2) {
+ cpm->im_cpm_fcc3.gfmr &= ~(FCC_GFMR_ENT | FCC_GFMR_ENR);
+ }
+}
+
+int fec_initialize(bd_t *bis)
+{
+ struct eth_device* dev;
+ int i;
+
+ for (i = 0; i < sizeof(ether_fcc_info) / sizeof(ether_fcc_info[0]); i++)
+ {
+ dev = (struct eth_device*) malloc(sizeof *dev);
+ memset(dev, 0, sizeof *dev);
+
+ sprintf(dev->name, "FCC%d",
+ ether_fcc_info[i].ether_index + 1);
+ dev->priv = ðer_fcc_info[i];
+ dev->init = fec_init;
+ dev->halt = fec_halt;
+ dev->send = fec_send;
+ dev->recv = fec_recv;
+
+ eth_register(dev);
+
+#if (defined(CONFIG_MII) || defined(CONFIG_CMD_MII)) \
+ && defined(CONFIG_BITBANGMII)
+ miiphy_register(dev->name,
+ bb_miiphy_read, bb_miiphy_write);
+#endif
+ }
+
+ return 1;
+}
+
+#endif
Code Review / kvmfornfv.git / blobdiff