--- /dev/null
+/*
+ * (C) Copyright 2000 - 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <config.h>
+#include <mpc824x.h>
+#include <common.h>
+#include <command.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkcpu (void)
+{
+ unsigned int pvr = get_pvr ();
+ unsigned int version = pvr >> 16;
+ unsigned char revision;
+ ulong clock = gd->cpu_clk;
+ char buf[32];
+
+ puts ("CPU: ");
+
+ switch (version) {
+ case CPU_TYPE_8240:
+ puts ("MPC8240");
+ break;
+
+ case CPU_TYPE_8245:
+ puts ("MPC8245");
+ break;
+
+ default:
+ return -1; /*not valid for this source */
+ }
+
+ CONFIG_READ_BYTE (REVID, revision);
+
+ if (revision) {
+ printf (" Revision %d.%d",
+ (revision & 0xf0) >> 4,
+ (revision & 0x0f));
+ } else {
+ return -1; /* no valid CPU revision info */
+ }
+
+ printf(" at %s MHz: ", strmhz(buf, clock));
+
+ print_size(checkicache(), " I-Cache ");
+ print_size(checkdcache(), " D-Cache\n");
+
+ return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+/* L1 i-cache */
+
+int checkicache (void)
+{
+ /*TODO*/
+ return 128 * 4 * 32;
+};
+
+/* ------------------------------------------------------------------------- */
+/* L1 d-cache */
+
+int checkdcache (void)
+{
+ /*TODO*/
+ return 128 * 4 * 32;
+
+};
+
+/*------------------------------------------------------------------- */
+
+int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ ulong msr, addr;
+
+ /* Interrupts and MMU off */
+ __asm__ ("mtspr 81, 0");
+
+ /* Interrupts and MMU off */
+ __asm__ __volatile__ ("mfmsr %0":"=r" (msr):);
+
+ msr &= ~0x1030;
+ __asm__ __volatile__ ("mtmsr %0"::"r" (msr));
+
+ /*
+ * Trying to execute the next instruction at a non-existing address
+ * should cause a machine check, resulting in reset
+ */
+#ifdef CONFIG_SYS_RESET_ADDRESS
+ addr = CONFIG_SYS_RESET_ADDRESS;
+#else
+ /*
+ * note: when CONFIG_SYS_MONITOR_BASE points to a RAM address,
+ * CONFIG_SYS_MONITOR_BASE - sizeof (ulong) is usually a valid
+ * address. Better pick an address known to be invalid on
+ * your system and assign it to CONFIG_SYS_RESET_ADDRESS.
+ * "(ulong)-1" used to be a good choice for many systems...
+ */
+ addr = CONFIG_SYS_MONITOR_BASE - sizeof (ulong);
+#endif
+ ((void (*)(void)) addr) ();
+ return 1;
+
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Get timebase clock frequency (like cpu_clk in Hz)
+ * This is the sys_logic_clk (memory bus) divided by 4
+ */
+unsigned long get_tbclk (void)
+{
+ return ((get_bus_freq (0) + 2L) / 4L);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * The MPC824x has an integrated PCI controller known as the MPC107.
+ * The following are MPC107 Bridge Controller and PCI Support functions
+ *
+ */
+
+/*
+ * This procedure reads a 32-bit address MPC107 register, and returns
+ * a 32 bit value. It swaps the address to little endian before
+ * writing it to config address, and swaps the value to big endian
+ * before returning to the caller.
+ */
+unsigned int mpc824x_mpc107_getreg (unsigned int regNum)
+{
+ unsigned int temp;
+
+ /* swap the addr. to little endian */
+ *(volatile unsigned int *) CHRP_REG_ADDR = PCISWAP (regNum);
+ temp = *(volatile unsigned int *) CHRP_REG_DATA;
+ return PCISWAP (temp); /* swap the data upon return */
+}
+
+/*
+ * This procedure writes a 32-bit address MPC107 register. It swaps
+ * the address to little endian before writing it to config address.
+ */
+
+void mpc824x_mpc107_setreg (unsigned int regNum, unsigned int regVal)
+{
+ /* swap the addr. to little endian */
+ *(volatile unsigned int *) CHRP_REG_ADDR = PCISWAP (regNum);
+ *(volatile unsigned int *) CHRP_REG_DATA = PCISWAP (regVal);
+ return;
+}
+
+
+/*
+ * Write a byte (8 bits) to a memory location.
+ */
+void mpc824x_mpc107_write8 (unsigned int addr, unsigned char data)
+{
+ *(unsigned char *) addr = data;
+ __asm__ ("sync");
+}
+
+/*
+ * Write a word (16 bits) to a memory location after the value
+ * has been byte swapped (big to little endian or vice versa)
+ */
+
+void mpc824x_mpc107_write16 (unsigned int address, unsigned short data)
+{
+ *(volatile unsigned short *) address = BYTE_SWAP_16_BIT (data);
+ __asm__ ("sync");
+}
+
+/*
+ * Write a long word (32 bits) to a memory location after the value
+ * has been byte swapped (big to little endian or vice versa)
+ */
+
+void mpc824x_mpc107_write32 (unsigned int address, unsigned int data)
+{
+ *(volatile unsigned int *) address = LONGSWAP (data);
+ __asm__ ("sync");
+}
+
+/*
+ * Read a byte (8 bits) from a memory location.
+ */
+unsigned char mpc824x_mpc107_read8 (unsigned int addr)
+{
+ return *(volatile unsigned char *) addr;
+}
+
+
+/*
+ * Read a word (16 bits) from a memory location, and byte swap the
+ * value before returning to the caller.
+ */
+unsigned short mpc824x_mpc107_read16 (unsigned int address)
+{
+ unsigned short retVal;
+
+ retVal = BYTE_SWAP_16_BIT (*(unsigned short *) address);
+ return retVal;
+}
+
+
+/*
+ * Read a long word (32 bits) from a memory location, and byte
+ * swap the value before returning to the caller.
+ */
+unsigned int mpc824x_mpc107_read32 (unsigned int address)
+{
+ unsigned int retVal;
+
+ retVal = LONGSWAP (*(unsigned int *) address);
+ return (retVal);
+}
+
+
+/*
+ * Read a register in the Embedded Utilities Memory Block address
+ * space.
+ * Input: regNum - register number + utility base address. Example,
+ * the base address of EPIC is 0x40000, the register number
+ * being passed is 0x40000+the address of the target register.
+ * (See epic.h for register addresses).
+ * Output: The 32 bit little endian value of the register.
+ */
+
+unsigned int mpc824x_eummbar_read (unsigned int regNum)
+{
+ unsigned int temp;
+
+ temp = *(volatile unsigned int *) (EUMBBAR_VAL + regNum);
+ temp = PCISWAP (temp);
+ return temp;
+}
+
+
+/*
+ * Write a value to a register in the Embedded Utilities Memory
+ * Block address space.
+ * Input: regNum - register number + utility base address. Example,
+ * the base address of EPIC is 0x40000, the register
+ * number is 0x40000+the address of the target register.
+ * (See epic.h for register addresses).
+ * regVal - value to be written to the register.
+ */
+
+void mpc824x_eummbar_write (unsigned int regNum, unsigned int regVal)
+{
+ *(volatile unsigned int *) (EUMBBAR_VAL + regNum) = PCISWAP (regVal);
+ return;
+}
+
+/* ------------------------------------------------------------------------- */
Code Review / kvmfornfv.git / blobdiff