Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / arch / blackfin / cpu / cache.S

diff --git a/qemu/roms/u-boot/arch/blackfin/cpu/cache.S b/qemu/roms/u-boot/arch/blackfin/cpu/cache.S
new file mode 100644 (file)
index 0000000..5ca9e91
--- /dev/null
+++ b/qemu/roms/u-boot/arch/blackfin/cpu/cache.S
@@ -0,0 +1,87 @@
+/*
+ * Blackfin cache control code
+ *
+ * Copyright 2003-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <config.h>
+#include <linux/linkage.h>
+#include <asm/blackfin.h>
+
+.text
+/* Since all L1 caches work the same way, we use the same method for flushing
+ * them.  Only the actual flush instruction differs.  We write this in asm as
+ * GCC can be hard to coax into writing nice hardware loops.
+ *
+ * Also, we assume the following register setup:
+ * R0 = start address
+ * R1 = end address
+ */
+.macro do_flush flushins:req optflushins optnopins label
+
+       R2 = -L1_CACHE_BYTES;
+
+       /* start = (start & -L1_CACHE_BYTES) */
+       R0 = R0 & R2;
+
+       /* end = ((end - 1) & -L1_CACHE_BYTES) + L1_CACHE_BYTES; */
+       R1 += -1;
+       R1 = R1 & R2;
+       R1 += L1_CACHE_BYTES;
+
+       /* count = (end - start) >> L1_CACHE_SHIFT */
+       R2 = R1 - R0;
+       R2 >>= L1_CACHE_SHIFT;
+       P1 = R2;
+
+.ifnb \label
+\label :
+.endif
+       P0 = R0;
+       LSETUP (1f, 2f) LC1 = P1;
+1:
+.ifnb \optflushins
+       \optflushins [P0];
+.endif
+#if ANOMALY_05000443
+.ifb \optnopins
+2:
+.endif
+       \flushins [P0++];
+.ifnb \optnopins
+2:     \optnopins;
+.endif
+#else
+2:     \flushins [P0++];
+#endif
+
+       RTS;
+.endm
+
+/* Invalidate all instruction cache lines assocoiated with this memory area */
+ENTRY(_blackfin_icache_flush_range)
+       do_flush IFLUSH, , nop
+ENDPROC(_blackfin_icache_flush_range)
+
+/* Flush all cache lines assocoiated with this area of memory. */
+ENTRY(_blackfin_icache_dcache_flush_range)
+       do_flush FLUSH, IFLUSH
+ENDPROC(_blackfin_icache_dcache_flush_range)
+
+/* Throw away all D-cached data in specified region without any obligation to
+ * write them back.  Since the Blackfin ISA does not have an "invalidate"
+ * instruction, we use flush/invalidate.  Perhaps as a speed optimization we
+ * could bang on the DTEST MMRs ...
+ */
+ENTRY(_blackfin_dcache_flush_invalidate_range)
+       do_flush FLUSHINV
+ENDPROC(_blackfin_dcache_flush_invalidate_range)
+
+/* Flush all data cache lines assocoiated with this memory area */
+ENTRY(_blackfin_dcache_flush_range)
+       do_flush FLUSH, , , .Ldfr
+ENDPROC(_blackfin_dcache_flush_range)