Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / arch / arm / cpu / armv7 / exynos / dmc_common.c

diff --git a/qemu/roms/u-boot/arch/arm/cpu/armv7/exynos/dmc_common.c b/qemu/roms/u-boot/arch/arm/cpu/armv7/exynos/dmc_common.c
new file mode 100644 (file)
index 0000000..cca925e
--- /dev/null
+++ b/qemu/roms/u-boot/arch/arm/cpu/armv7/exynos/dmc_common.c
@@ -0,0 +1,176 @@
+/*
+ * Mem setup common file for different types of DDR present on Exynos boards.
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/spl.h>
+
+#include "clock_init.h"
+#include "common_setup.h"
+#include "exynos5_setup.h"
+
+#define ZQ_INIT_TIMEOUT        10000
+
+int dmc_config_zq(struct mem_timings *mem, uint32_t *phy0_con16,
+                       uint32_t *phy1_con16, uint32_t *phy0_con17,
+                       uint32_t *phy1_con17)
+{
+       unsigned long val = 0;
+       int i;
+
+       /*
+        * ZQ Calibration:
+        * Select Driver Strength,
+        * long calibration for manual calibration
+        */
+       val = PHY_CON16_RESET_VAL;
+       val |= mem->zq_mode_dds << PHY_CON16_ZQ_MODE_DDS_SHIFT;
+       val |= mem->zq_mode_term << PHY_CON16_ZQ_MODE_TERM_SHIFT;
+       val |= ZQ_CLK_DIV_EN;
+       writel(val, phy0_con16);
+       writel(val, phy1_con16);
+
+       /* Disable termination */
+       if (mem->zq_mode_noterm)
+               val |= PHY_CON16_ZQ_MODE_NOTERM_MASK;
+       writel(val, phy0_con16);
+       writel(val, phy1_con16);
+
+       /* ZQ_MANUAL_START: Enable */
+       val |= ZQ_MANUAL_STR;
+       writel(val, phy0_con16);
+       writel(val, phy1_con16);
+
+       /* ZQ_MANUAL_START: Disable */
+       val &= ~ZQ_MANUAL_STR;
+
+       /*
+        * Since we are manaully calibrating the ZQ values,
+        * we are looping for the ZQ_init to complete.
+        */
+       i = ZQ_INIT_TIMEOUT;
+       while ((readl(phy0_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+               sdelay(100);
+               i--;
+       }
+       if (!i)
+               return -1;
+       writel(val, phy0_con16);
+
+       i = ZQ_INIT_TIMEOUT;
+       while ((readl(phy1_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+               sdelay(100);
+               i--;
+       }
+       if (!i)
+               return -1;
+       writel(val, phy1_con16);
+
+       return 0;
+}
+
+void update_reset_dll(uint32_t *phycontrol0, enum ddr_mode mode)
+{
+       unsigned long val;
+
+       if (mode == DDR_MODE_DDR3) {
+               val = MEM_TERM_EN | PHY_TERM_EN | DMC_CTRL_SHGATE;
+               writel(val, phycontrol0);
+       }
+
+       /* Update DLL Information: Force DLL Resyncronization */
+       val = readl(phycontrol0);
+       val |= FP_RSYNC;
+       writel(val, phycontrol0);
+
+       /* Reset Force DLL Resyncronization */
+       val = readl(phycontrol0);
+       val &= ~FP_RSYNC;
+       writel(val, phycontrol0);
+}
+
+void dmc_config_mrs(struct mem_timings *mem, uint32_t *directcmd)
+{
+       int channel, chip;
+
+       for (channel = 0; channel < mem->dmc_channels; channel++) {
+               unsigned long mask;
+
+               mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
+               for (chip = 0; chip < mem->chips_to_configure; chip++) {
+                       int i;
+
+                       mask |= chip << DIRECT_CMD_CHIP_SHIFT;
+
+                       /* Sending NOP command */
+                       writel(DIRECT_CMD_NOP | mask, directcmd);
+
+                       /*
+                        * TODO(alim.akhtar@samsung.com): Do we need these
+                        * delays? This one and the next were not there for
+                        * DDR3.
+                        */
+                       sdelay(0x10000);
+
+                       /* Sending EMRS/MRS commands */
+                       for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
+                               writel(mem->direct_cmd_msr[i] | mask,
+                                      directcmd);
+                               sdelay(0x10000);
+                       }
+
+                       if (mem->send_zq_init) {
+                               /* Sending ZQINIT command */
+                               writel(DIRECT_CMD_ZQINIT | mask,
+                                      directcmd);
+
+                               sdelay(10000);
+                       }
+               }
+       }
+}
+
+void dmc_config_prech(struct mem_timings *mem, uint32_t *directcmd)
+{
+       int channel, chip;
+
+       for (channel = 0; channel < mem->dmc_channels; channel++) {
+               unsigned long mask;
+
+               mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
+               for (chip = 0; chip < mem->chips_per_channel; chip++) {
+                       mask |= chip << DIRECT_CMD_CHIP_SHIFT;
+
+                       /* PALL (all banks precharge) CMD */
+                       writel(DIRECT_CMD_PALL | mask, directcmd);
+                       sdelay(0x10000);
+               }
+       }
+}
+
+void mem_ctrl_init(int reset)
+{
+       struct spl_machine_param *param = spl_get_machine_params();
+       struct mem_timings *mem;
+       int ret;
+
+       mem = clock_get_mem_timings();
+
+       /* If there are any other memory variant, add their init call below */
+       if (param->mem_type == DDR_MODE_DDR3) {
+               ret = ddr3_mem_ctrl_init(mem, param->mem_iv_size, reset);
+               if (ret) {
+                       /* will hang if failed to init memory control */
+                       while (1)
+                               ;
+               }
+       } else {
+               /* will hang if unknow memory type  */
+               while (1)
+                       ;
+       }
+}