--- /dev/null
+/*------------------------------------------------------------------------
+ * smc9000.h
+ *
+ * Copyright (C) 1998 by Daniel Engström
+ * Copyright (C) 1996 by Erik Stahlman
+ *
+ * This software may be used and distributed according to the terms
+ * of the GNU Public License, incorporated herein by reference.
+ *
+ * This file contains register information and access macros for
+ * the SMC91xxx chipset.
+ *
+ * Information contained in this file was obtained from the SMC91C94
+ * manual from SMC. To get a copy, if you really want one, you can find
+ * information under www.smsc.com in the components division.
+ * ( this thanks to advice from Donald Becker ).
+ *
+ * Authors
+ * Daniel Engström <daniel.engstrom@riksnett.no>
+ * Erik Stahlman <erik@vt.edu>
+ *
+ * History
+ * 96-01-06 Erik Stahlman moved definitions here from main .c
+ * file
+ * 96-01-19 Erik Stahlman polished this up some, and added
+ * better error handling
+ * 98-09-25 Daniel Engström adjusted for Etherboot
+ * 98-09-27 Daniel Engström moved some static strings back to the
+ * main .c file
+ * --------------------------------------------------------------------------*/
+
+FILE_LICENCE ( GPL_ANY );
+
+#ifndef _SMC9000_H_
+# define _SMC9000_H_
+
+/* I want some simple types */
+typedef unsigned char byte;
+typedef unsigned short word;
+typedef unsigned long int dword;
+
+/*---------------------------------------------------------------
+ *
+ * A description of the SMC registers is probably in order here,
+ * although for details, the SMC datasheet is invaluable.
+ *
+ * Basically, the chip has 4 banks of registers ( 0 to 3 ), which
+ * are accessed by writing a number into the BANK_SELECT register
+ * ( I also use a SMC_SELECT_BANK macro for this ).
+ *
+ * The banks are configured so that for most purposes, bank 2 is all
+ * that is needed for simple run time tasks.
+ * ----------------------------------------------------------------------*/
+
+/*
+ * Bank Select Register:
+ *
+ * yyyy yyyy 0000 00xx
+ * xx = bank number
+ * yyyy yyyy = 0x33, for identification purposes.
+ */
+#define BANK_SELECT 14
+
+/* BANK 0 */
+
+#define TCR 0 /* transmit control register */
+#define TCR_ENABLE 0x0001 /* if this is 1, we can transmit */
+#define TCR_FDUPLX 0x0800 /* receive packets sent out */
+#define TCR_STP_SQET 0x1000 /* stop transmitting if Signal quality error */
+#define TCR_MON_CNS 0x0400 /* monitors the carrier status */
+#define TCR_PAD_ENABLE 0x0080 /* pads short packets to 64 bytes */
+
+#define TCR_CLEAR 0 /* do NOTHING */
+/* the normal settings for the TCR register : */
+#define TCR_NORMAL (TCR_ENABLE | TCR_PAD_ENABLE)
+
+
+#define EPH_STATUS 2
+#define ES_LINK_OK 0x4000 /* is the link integrity ok ? */
+
+#define RCR 4
+#define RCR_SOFTRESET 0x8000 /* resets the chip */
+#define RCR_STRIP_CRC 0x200 /* strips CRC */
+#define RCR_ENABLE 0x100 /* IFF this is set, we can receive packets */
+#define RCR_ALMUL 0x4 /* receive all multicast packets */
+#define RCR_PROMISC 0x2 /* enable promiscuous mode */
+
+/* the normal settings for the RCR register : */
+#define RCR_NORMAL (RCR_STRIP_CRC | RCR_ENABLE)
+#define RCR_CLEAR 0x0 /* set it to a base state */
+
+#define COUNTER 6
+#define MIR 8
+#define MCR 10
+/* 12 is reserved */
+
+// Receive/Phy Control Register
+/* BANK 0 */
+#define RPC_REG 0x000A
+#define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode.
+#define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode
+#define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode
+#define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb
+#define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb
+#define RPC_LED_100_10 (0x00) // LED = 100Mbps OR's with 10Mbps link detect
+#define RPC_LED_RES (0x01) // LED = Reserved
+#define RPC_LED_10 (0x02) // LED = 10Mbps link detect
+#define RPC_LED_FD (0x03) // LED = Full Duplex Mode
+#define RPC_LED_TX_RX (0x04) // LED = TX or RX packet occurred
+#define RPC_LED_100 (0x05) // LED = 100Mbps link detect
+#define RPC_LED_TX (0x06) // LED = TX packet occurred
+#define RPC_LED_RX (0x07) // LED = RX packet occurred
+#define RPC_DEFAULT (RPC_ANEG | (RPC_LED_100 << RPC_LSXA_SHFT) | (RPC_LED_FD << RPC_LSXB_SHFT) | RPC_SPEED | RPC_DPLX)
+
+// Receive/Phy Control Register
+/* BANK 0 */
+#define RPC_REG 0x000A
+#define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode.
+#define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode
+#define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode
+#define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb
+#define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb
+#define RPC_LED_100_10 (0x00) // LED = 100Mbps OR's with 10Mbps link detect
+#define RPC_LED_RES (0x01) // LED = Reserved
+#define RPC_LED_10 (0x02) // LED = 10Mbps link detect
+#define RPC_LED_FD (0x03) // LED = Full Duplex Mode
+#define RPC_LED_TX_RX (0x04) // LED = TX or RX packet occurred
+#define RPC_LED_100 (0x05) // LED = 100Mbps link detect
+#define RPC_LED_TX (0x06) // LED = TX packet occurred
+#define RPC_LED_RX (0x07) // LED = RX packet occurred
+#define RPC_DEFAULT (RPC_ANEG | (RPC_LED_100 << RPC_LSXA_SHFT) | (RPC_LED_FD << RPC_LSXB_SHFT) | RPC_SPEED | RPC_DPLX)
+
+/* BANK 1 */
+#define CFG 0
+#define CFG_AUI_SELECT 0x100
+#define BASE 2
+#define ADDR0 4
+#define ADDR1 6
+#define ADDR2 8
+#define GENERAL 10
+#define CONTROL 12
+#define CTL_POWERDOWN 0x2000
+#define CTL_LE_ENABLE 0x80
+#define CTL_CR_ENABLE 0x40
+#define CTL_TE_ENABLE 0x0020
+#define CTL_AUTO_RELEASE 0x0800
+#define CTL_EPROM_ACCESS 0x0003 /* high if Eprom is being read */
+
+/* BANK 2 */
+#define MMU_CMD 0
+#define MC_BUSY 1 /* only readable bit in the register */
+#define MC_NOP 0
+#define MC_ALLOC 0x20 /* or with number of 256 byte packets */
+#define MC_RESET 0x40
+#define MC_REMOVE 0x60 /* remove the current rx packet */
+#define MC_RELEASE 0x80 /* remove and release the current rx packet */
+#define MC_FREEPKT 0xA0 /* Release packet in PNR register */
+#define MC_ENQUEUE 0xC0 /* Enqueue the packet for transmit */
+
+#define PNR_ARR 2
+#define FIFO_PORTS 4
+
+#define FP_RXEMPTY 0x8000
+#define FP_TXEMPTY 0x80
+
+#define POINTER 6
+#define PTR_READ 0x2000
+#define PTR_RCV 0x8000
+#define PTR_AUTOINC 0x4000
+#define PTR_AUTO_INC 0x0040
+
+#define DATA_1 8
+#define DATA_2 10
+#define INTERRUPT 12
+
+#define INT_MASK 13
+#define IM_RCV_INT 0x1
+#define IM_TX_INT 0x2
+#define IM_TX_EMPTY_INT 0x4
+#define IM_ALLOC_INT 0x8
+#define IM_RX_OVRN_INT 0x10
+#define IM_EPH_INT 0x20
+#define IM_ERCV_INT 0x40 /* not on SMC9192 */
+
+/* BANK 3 */
+#define MULTICAST1 0
+#define MULTICAST2 2
+#define MULTICAST3 4
+#define MULTICAST4 6
+#define MGMT 8
+#define REVISION 10 /* ( hi: chip id low: rev # ) */
+
+// Management Interface Register (MII)
+#define MII_REG 0x0008
+#define MII_MSK_CRS100 0x4000 // Disables CRS100 detection during tx half dup
+#define MII_MDOE 0x0008 // MII Output Enable
+#define MII_MCLK 0x0004 // MII Clock, pin MDCLK
+#define MII_MDI 0x0002 // MII Input, pin MDI
+#define MII_MDO 0x0001 // MII Output, pin MDO
+
+/* this is NOT on SMC9192 */
+#define ERCV 12
+
+/* Note that 9194 and 9196 have the smame chip id,
+ * the 9196 will have revisions starting at 6 */
+#define CHIP_9190 3
+#define CHIP_9194 4
+#define CHIP_9195 5
+#define CHIP_9196 4
+#define CHIP_91100 7
+#define CHIP_91100FD 8
+
+#define REV_9196 6
+
+/*
+ * Transmit status bits
+ */
+#define TS_SUCCESS 0x0001
+#define TS_LOSTCAR 0x0400
+#define TS_LATCOL 0x0200
+#define TS_16COL 0x0010
+
+/*
+ * Receive status bits
+ */
+#define RS_ALGNERR 0x8000
+#define RS_BADCRC 0x2000
+#define RS_ODDFRAME 0x1000
+#define RS_TOOLONG 0x0800
+#define RS_TOOSHORT 0x0400
+#define RS_MULTICAST 0x0001
+#define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT)
+
+// PHY Register Addresses (LAN91C111 Internal PHY)
+
+// PHY Control Register
+#define PHY_CNTL_REG 0x00
+#define PHY_CNTL_RST 0x8000 // 1=PHY Reset
+#define PHY_CNTL_LPBK 0x4000 // 1=PHY Loopback
+#define PHY_CNTL_SPEED 0x2000 // 1=100Mbps, 0=10Mpbs
+#define PHY_CNTL_ANEG_EN 0x1000 // 1=Enable Auto negotiation
+#define PHY_CNTL_PDN 0x0800 // 1=PHY Power Down mode
+#define PHY_CNTL_MII_DIS 0x0400 // 1=MII 4 bit interface disabled
+#define PHY_CNTL_ANEG_RST 0x0200 // 1=Reset Auto negotiate
+#define PHY_CNTL_DPLX 0x0100 // 1=Full Duplex, 0=Half Duplex
+#define PHY_CNTL_COLTST 0x0080 // 1= MII Colision Test
+
+// PHY Status Register
+#define PHY_STAT_REG 0x01
+#define PHY_STAT_CAP_T4 0x8000 // 1=100Base-T4 capable
+#define PHY_STAT_CAP_TXF 0x4000 // 1=100Base-X full duplex capable
+#define PHY_STAT_CAP_TXH 0x2000 // 1=100Base-X half duplex capable
+#define PHY_STAT_CAP_TF 0x1000 // 1=10Mbps full duplex capable
+#define PHY_STAT_CAP_TH 0x0800 // 1=10Mbps half duplex capable
+#define PHY_STAT_CAP_SUPR 0x0040 // 1=recv mgmt frames with not preamble
+#define PHY_STAT_ANEG_ACK 0x0020 // 1=ANEG has completed
+#define PHY_STAT_REM_FLT 0x0010 // 1=Remote Fault detected
+#define PHY_STAT_CAP_ANEG 0x0008 // 1=Auto negotiate capable
+#define PHY_STAT_LINK 0x0004 // 1=valid link
+#define PHY_STAT_JAB 0x0002 // 1=10Mbps jabber condition
+#define PHY_STAT_EXREG 0x0001 // 1=extended registers implemented
+
+// PHY Identifier Registers
+#define PHY_ID1_REG 0x02 // PHY Identifier 1
+#define PHY_ID2_REG 0x03 // PHY Identifier 2
+
+// PHY Auto-Negotiation Advertisement Register
+#define PHY_AD_REG 0x04
+#define PHY_AD_NP 0x8000 // 1=PHY requests exchange of Next Page
+#define PHY_AD_ACK 0x4000 // 1=got link code word from remote
+#define PHY_AD_RF 0x2000 // 1=advertise remote fault
+#define PHY_AD_T4 0x0200 // 1=PHY is capable of 100Base-T4
+#define PHY_AD_TX_FDX 0x0100 // 1=PHY is capable of 100Base-TX FDPLX
+#define PHY_AD_TX_HDX 0x0080 // 1=PHY is capable of 100Base-TX HDPLX
+#define PHY_AD_10_FDX 0x0040 // 1=PHY is capable of 10Base-T FDPLX
+#define PHY_AD_10_HDX 0x0020 // 1=PHY is capable of 10Base-T HDPLX
+#define PHY_AD_CSMA 0x0001 // 1=PHY is capable of 802.3 CMSA
+
+// PHY Auto-negotiation Remote End Capability Register
+#define PHY_RMT_REG 0x05
+// Uses same bit definitions as PHY_AD_REG
+
+// PHY Configuration Register 1
+#define PHY_CFG1_REG 0x10
+#define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled
+#define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled
+#define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down
+#define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler
+#define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable
+#define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled
+#define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm)
+#define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
+#define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust
+#define PHY_CFG1_TLVL_MASK 0x003C
+#define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time
+
+
+// PHY Configuration Register 2
+#define PHY_CFG2_REG 0x11
+#define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled
+#define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled
+#define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt)
+#define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo
+
+// PHY Status Output (and Interrupt status) Register
+#define PHY_INT_REG 0x12 // Status Output (Interrupt Status)
+#define PHY_INT_INT 0x8000 // 1=bits have changed since last read
+#define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected
+#define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync
+#define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx
+#define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx
+#define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx
+#define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected
+#define PHY_INT_JAB 0x0100 // 1=Jabber detected
+#define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode
+#define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex
+
+// PHY Interrupt/Status Mask Register
+#define PHY_MASK_REG 0x13 // Interrupt Mask
+// Uses the same bit definitions as PHY_INT_REG
+
+
+// PHY Register Addresses (LAN91C111 Internal PHY)
+
+// PHY Control Register
+#define PHY_CNTL_REG 0x00
+#define PHY_CNTL_RST 0x8000 // 1=PHY Reset
+#define PHY_CNTL_LPBK 0x4000 // 1=PHY Loopback
+#define PHY_CNTL_SPEED 0x2000 // 1=100Mbps, 0=10Mpbs
+#define PHY_CNTL_ANEG_EN 0x1000 // 1=Enable Auto negotiation
+#define PHY_CNTL_PDN 0x0800 // 1=PHY Power Down mode
+#define PHY_CNTL_MII_DIS 0x0400 // 1=MII 4 bit interface disabled
+#define PHY_CNTL_ANEG_RST 0x0200 // 1=Reset Auto negotiate
+#define PHY_CNTL_DPLX 0x0100 // 1=Full Duplex, 0=Half Duplex
+#define PHY_CNTL_COLTST 0x0080 // 1= MII Colision Test
+
+// PHY Status Register
+#define PHY_STAT_REG 0x01
+#define PHY_STAT_CAP_T4 0x8000 // 1=100Base-T4 capable
+#define PHY_STAT_CAP_TXF 0x4000 // 1=100Base-X full duplex capable
+#define PHY_STAT_CAP_TXH 0x2000 // 1=100Base-X half duplex capable
+#define PHY_STAT_CAP_TF 0x1000 // 1=10Mbps full duplex capable
+#define PHY_STAT_CAP_TH 0x0800 // 1=10Mbps half duplex capable
+#define PHY_STAT_CAP_SUPR 0x0040 // 1=recv mgmt frames with not preamble
+#define PHY_STAT_ANEG_ACK 0x0020 // 1=ANEG has completed
+#define PHY_STAT_REM_FLT 0x0010 // 1=Remote Fault detected
+#define PHY_STAT_CAP_ANEG 0x0008 // 1=Auto negotiate capable
+#define PHY_STAT_LINK 0x0004 // 1=valid link
+#define PHY_STAT_JAB 0x0002 // 1=10Mbps jabber condition
+#define PHY_STAT_EXREG 0x0001 // 1=extended registers implemented
+
+// PHY Identifier Registers
+#define PHY_ID1_REG 0x02 // PHY Identifier 1
+#define PHY_ID2_REG 0x03 // PHY Identifier 2
+
+// PHY Auto-Negotiation Advertisement Register
+#define PHY_AD_REG 0x04
+#define PHY_AD_NP 0x8000 // 1=PHY requests exchange of Next Page
+#define PHY_AD_ACK 0x4000 // 1=got link code word from remote
+#define PHY_AD_RF 0x2000 // 1=advertise remote fault
+#define PHY_AD_T4 0x0200 // 1=PHY is capable of 100Base-T4
+#define PHY_AD_TX_FDX 0x0100 // 1=PHY is capable of 100Base-TX FDPLX
+#define PHY_AD_TX_HDX 0x0080 // 1=PHY is capable of 100Base-TX HDPLX
+#define PHY_AD_10_FDX 0x0040 // 1=PHY is capable of 10Base-T FDPLX
+#define PHY_AD_10_HDX 0x0020 // 1=PHY is capable of 10Base-T HDPLX
+#define PHY_AD_CSMA 0x0001 // 1=PHY is capable of 802.3 CMSA
+
+// PHY Auto-negotiation Remote End Capability Register
+#define PHY_RMT_REG 0x05
+// Uses same bit definitions as PHY_AD_REG
+
+// PHY Configuration Register 1
+#define PHY_CFG1_REG 0x10
+#define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled
+#define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled
+#define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down
+#define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler
+#define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable
+#define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled
+#define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm)
+#define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
+#define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust
+#define PHY_CFG1_TLVL_MASK 0x003C
+#define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time
+
+
+// PHY Configuration Register 2
+#define PHY_CFG2_REG 0x11
+#define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled
+#define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled
+#define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt)
+#define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo
+
+// PHY Status Output (and Interrupt status) Register
+#define PHY_INT_REG 0x12 // Status Output (Interrupt Status)
+#define PHY_INT_INT 0x8000 // 1=bits have changed since last read
+#define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected
+#define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync
+#define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx
+#define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx
+#define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx
+#define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected
+#define PHY_INT_JAB 0x0100 // 1=Jabber detected
+#define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode
+#define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex
+
+// PHY Interrupt/Status Mask Register
+#define PHY_MASK_REG 0x13 // Interrupt Mask
+// Uses the same bit definitions as PHY_INT_REG
+
+
+/*-------------------------------------------------------------------------
+ * I define some macros to make it easier to do somewhat common
+ * or slightly complicated, repeated tasks.
+ --------------------------------------------------------------------------*/
+
+/* select a register bank, 0 to 3 */
+
+#define SMC_SELECT_BANK(x, y) { _outw( y, x + BANK_SELECT ); }
+
+/* define a small delay for the reset */
+#define SMC_DELAY(x) { inw( x + RCR );\
+ inw( x + RCR );\
+ inw( x + RCR ); }
+
+
+#endif /* _SMC_9000_H_ */
+
Code Review / kvmfornfv.git / blobdiff