--- /dev/null
+/*
+ * Copyright (c) 2010-2011 Atheros Communications Inc.
+ *
+ * Modified for iPXE by Scott K Logan <logans@cottsay.net> July 2011
+ * Original from Linux kernel 3.0.1
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef AR9003_EEPROM_H
+#define AR9003_EEPROM_H
+
+FILE_LICENCE ( BSD2 );
+
+#define AR9300_EEP_VER 0xD000
+#define AR9300_EEP_VER_MINOR_MASK 0xFFF
+#define AR9300_EEP_MINOR_VER_1 0x1
+#define AR9300_EEP_MINOR_VER AR9300_EEP_MINOR_VER_1
+
+/* 16-bit offset location start of calibration struct */
+#define AR9300_EEP_START_LOC 256
+#define AR9300_NUM_5G_CAL_PIERS 8
+#define AR9300_NUM_2G_CAL_PIERS 3
+#define AR9300_NUM_5G_20_TARGET_POWERS 8
+#define AR9300_NUM_5G_40_TARGET_POWERS 8
+#define AR9300_NUM_2G_CCK_TARGET_POWERS 2
+#define AR9300_NUM_2G_20_TARGET_POWERS 3
+#define AR9300_NUM_2G_40_TARGET_POWERS 3
+/* #define AR9300_NUM_CTLS 21 */
+#define AR9300_NUM_CTLS_5G 9
+#define AR9300_NUM_CTLS_2G 12
+#define AR9300_NUM_BAND_EDGES_5G 8
+#define AR9300_NUM_BAND_EDGES_2G 4
+#define AR9300_EEPMISC_BIG_ENDIAN 0x01
+#define AR9300_EEPMISC_WOW 0x02
+#define AR9300_CUSTOMER_DATA_SIZE 20
+
+#define FBIN2FREQ(x, y) ((y) ? (2300 + x) : (4800 + 5 * x))
+#define AR9300_MAX_CHAINS 3
+#define AR9300_ANT_16S 25
+#define AR9300_FUTURE_MODAL_SZ 6
+
+#define AR9300_PAPRD_RATE_MASK 0x01ffffff
+#define AR9300_PAPRD_SCALE_1 0x0e000000
+#define AR9300_PAPRD_SCALE_1_S 25
+#define AR9300_PAPRD_SCALE_2 0x70000000
+#define AR9300_PAPRD_SCALE_2_S 28
+
+/* Delta from which to start power to pdadc table */
+/* This offset is used in both open loop and closed loop power control
+ * schemes. In open loop power control, it is not really needed, but for
+ * the "sake of consistency" it was kept. For certain AP designs, this
+ * value is overwritten by the value in the flag "pwrTableOffset" just
+ * before writing the pdadc vs pwr into the chip registers.
+ */
+#define AR9300_PWR_TABLE_OFFSET 0
+
+/* byte addressable */
+#define AR9300_EEPROM_SIZE (16*1024)
+
+#define AR9300_BASE_ADDR_4K 0xfff
+#define AR9300_BASE_ADDR 0x3ff
+#define AR9300_BASE_ADDR_512 0x1ff
+
+#define AR9300_OTP_BASE 0x14000
+#define AR9300_OTP_STATUS 0x15f18
+#define AR9300_OTP_STATUS_TYPE 0x7
+#define AR9300_OTP_STATUS_VALID 0x4
+#define AR9300_OTP_STATUS_ACCESS_BUSY 0x2
+#define AR9300_OTP_STATUS_SM_BUSY 0x1
+#define AR9300_OTP_READ_DATA 0x15f1c
+
+enum targetPowerHTRates {
+ HT_TARGET_RATE_0_8_16,
+ HT_TARGET_RATE_1_3_9_11_17_19,
+ HT_TARGET_RATE_4,
+ HT_TARGET_RATE_5,
+ HT_TARGET_RATE_6,
+ HT_TARGET_RATE_7,
+ HT_TARGET_RATE_12,
+ HT_TARGET_RATE_13,
+ HT_TARGET_RATE_14,
+ HT_TARGET_RATE_15,
+ HT_TARGET_RATE_20,
+ HT_TARGET_RATE_21,
+ HT_TARGET_RATE_22,
+ HT_TARGET_RATE_23
+};
+
+enum targetPowerLegacyRates {
+ LEGACY_TARGET_RATE_6_24,
+ LEGACY_TARGET_RATE_36,
+ LEGACY_TARGET_RATE_48,
+ LEGACY_TARGET_RATE_54
+};
+
+enum targetPowerCckRates {
+ LEGACY_TARGET_RATE_1L_5L,
+ LEGACY_TARGET_RATE_5S,
+ LEGACY_TARGET_RATE_11L,
+ LEGACY_TARGET_RATE_11S
+};
+
+enum ar9300_Rates {
+ ALL_TARGET_LEGACY_6_24,
+ ALL_TARGET_LEGACY_36,
+ ALL_TARGET_LEGACY_48,
+ ALL_TARGET_LEGACY_54,
+ ALL_TARGET_LEGACY_1L_5L,
+ ALL_TARGET_LEGACY_5S,
+ ALL_TARGET_LEGACY_11L,
+ ALL_TARGET_LEGACY_11S,
+ ALL_TARGET_HT20_0_8_16,
+ ALL_TARGET_HT20_1_3_9_11_17_19,
+ ALL_TARGET_HT20_4,
+ ALL_TARGET_HT20_5,
+ ALL_TARGET_HT20_6,
+ ALL_TARGET_HT20_7,
+ ALL_TARGET_HT20_12,
+ ALL_TARGET_HT20_13,
+ ALL_TARGET_HT20_14,
+ ALL_TARGET_HT20_15,
+ ALL_TARGET_HT20_20,
+ ALL_TARGET_HT20_21,
+ ALL_TARGET_HT20_22,
+ ALL_TARGET_HT20_23,
+ ALL_TARGET_HT40_0_8_16,
+ ALL_TARGET_HT40_1_3_9_11_17_19,
+ ALL_TARGET_HT40_4,
+ ALL_TARGET_HT40_5,
+ ALL_TARGET_HT40_6,
+ ALL_TARGET_HT40_7,
+ ALL_TARGET_HT40_12,
+ ALL_TARGET_HT40_13,
+ ALL_TARGET_HT40_14,
+ ALL_TARGET_HT40_15,
+ ALL_TARGET_HT40_20,
+ ALL_TARGET_HT40_21,
+ ALL_TARGET_HT40_22,
+ ALL_TARGET_HT40_23,
+ ar9300RateSize,
+};
+
+
+struct eepFlags {
+ u8 opFlags;
+ u8 eepMisc;
+} __attribute__((packed));
+
+enum CompressAlgorithm {
+ _CompressNone = 0,
+ _CompressLzma,
+ _CompressPairs,
+ _CompressBlock,
+ _Compress4,
+ _Compress5,
+ _Compress6,
+ _Compress7,
+};
+
+struct ar9300_base_eep_hdr {
+ uint16_t regDmn[2];
+ /* 4 bits tx and 4 bits rx */
+ u8 txrxMask;
+ struct eepFlags opCapFlags;
+ u8 rfSilent;
+ u8 blueToothOptions;
+ u8 deviceCap;
+ /* takes lower byte in eeprom location */
+ u8 deviceType;
+ /* offset in dB to be added to beginning
+ * of pdadc table in calibration
+ */
+ int8_t pwrTableOffset;
+ u8 params_for_tuning_caps[2];
+ /*
+ * bit0 - enable tx temp comp
+ * bit1 - enable tx volt comp
+ * bit2 - enable fastClock - default to 1
+ * bit3 - enable doubling - default to 1
+ * bit4 - enable internal regulator - default to 1
+ */
+ u8 featureEnable;
+ /* misc flags: bit0 - turn down drivestrength */
+ u8 miscConfiguration;
+ u8 eepromWriteEnableGpio;
+ u8 wlanDisableGpio;
+ u8 wlanLedGpio;
+ u8 rxBandSelectGpio;
+ u8 txrxgain;
+ /* SW controlled internal regulator fields */
+ uint32_t swreg;
+} __attribute__((packed));
+
+struct ar9300_modal_eep_header {
+ /* 4 idle, t1, t2, b (4 bits per setting) */
+ uint32_t antCtrlCommon;
+ /* 4 ra1l1, ra2l1, ra1l2, ra2l2, ra12 */
+ uint32_t antCtrlCommon2;
+ /* 6 idle, t, r, rx1, rx12, b (2 bits each) */
+ uint16_t antCtrlChain[AR9300_MAX_CHAINS];
+ /* 3 xatten1_db for AR9280 (0xa20c/b20c 5:0) */
+ u8 xatten1DB[AR9300_MAX_CHAINS];
+ /* 3 xatten1_margin for merlin (0xa20c/b20c 16:12 */
+ u8 xatten1Margin[AR9300_MAX_CHAINS];
+ int8_t tempSlope;
+ int8_t voltSlope;
+ /* spur channels in usual fbin coding format */
+ u8 spurChans[AR_EEPROM_MODAL_SPURS];
+ /* 3 Check if the register is per chain */
+ int8_t noiseFloorThreshCh[AR9300_MAX_CHAINS];
+ u8 ob[AR9300_MAX_CHAINS];
+ u8 db_stage2[AR9300_MAX_CHAINS];
+ u8 db_stage3[AR9300_MAX_CHAINS];
+ u8 db_stage4[AR9300_MAX_CHAINS];
+ u8 xpaBiasLvl;
+ u8 txFrameToDataStart;
+ u8 txFrameToPaOn;
+ u8 txClip;
+ int8_t antennaGain;
+ u8 switchSettling;
+ int8_t adcDesiredSize;
+ u8 txEndToXpaOff;
+ u8 txEndToRxOn;
+ u8 txFrameToXpaOn;
+ u8 thresh62;
+ uint32_t papdRateMaskHt20;
+ uint32_t papdRateMaskHt40;
+ u8 futureModal[10];
+} __attribute__((packed));
+
+struct ar9300_cal_data_per_freq_op_loop {
+ int8_t refPower;
+ /* pdadc voltage at power measurement */
+ u8 voltMeas;
+ /* pcdac used for power measurement */
+ u8 tempMeas;
+ /* range is -60 to -127 create a mapping equation 1db resolution */
+ int8_t rxNoisefloorCal;
+ /*range is same as noisefloor */
+ int8_t rxNoisefloorPower;
+ /* temp measured when noisefloor cal was performed */
+ u8 rxTempMeas;
+} __attribute__((packed));
+
+struct cal_tgt_pow_legacy {
+ u8 tPow2x[4];
+} __attribute__((packed));
+
+struct cal_tgt_pow_ht {
+ u8 tPow2x[14];
+} __attribute__((packed));
+
+struct cal_ctl_data_2g {
+ u8 ctlEdges[AR9300_NUM_BAND_EDGES_2G];
+} __attribute__((packed));
+
+struct cal_ctl_data_5g {
+ u8 ctlEdges[AR9300_NUM_BAND_EDGES_5G];
+} __attribute__((packed));
+
+struct ar9300_BaseExtension_1 {
+ u8 ant_div_control;
+ u8 future[13];
+} __attribute__((packed));
+
+struct ar9300_BaseExtension_2 {
+ int8_t tempSlopeLow;
+ int8_t tempSlopeHigh;
+ u8 xatten1DBLow[AR9300_MAX_CHAINS];
+ u8 xatten1MarginLow[AR9300_MAX_CHAINS];
+ u8 xatten1DBHigh[AR9300_MAX_CHAINS];
+ u8 xatten1MarginHigh[AR9300_MAX_CHAINS];
+} __attribute__((packed));
+
+struct ar9300_eeprom {
+ u8 eepromVersion;
+ u8 templateVersion;
+ u8 macAddr[6];
+ u8 custData[AR9300_CUSTOMER_DATA_SIZE];
+
+ struct ar9300_base_eep_hdr baseEepHeader;
+
+ struct ar9300_modal_eep_header modalHeader2G;
+ struct ar9300_BaseExtension_1 base_ext1;
+ u8 calFreqPier2G[AR9300_NUM_2G_CAL_PIERS];
+ struct ar9300_cal_data_per_freq_op_loop
+ calPierData2G[AR9300_MAX_CHAINS][AR9300_NUM_2G_CAL_PIERS];
+ u8 calTarget_freqbin_Cck[AR9300_NUM_2G_CCK_TARGET_POWERS];
+ u8 calTarget_freqbin_2G[AR9300_NUM_2G_20_TARGET_POWERS];
+ u8 calTarget_freqbin_2GHT20[AR9300_NUM_2G_20_TARGET_POWERS];
+ u8 calTarget_freqbin_2GHT40[AR9300_NUM_2G_40_TARGET_POWERS];
+ struct cal_tgt_pow_legacy
+ calTargetPowerCck[AR9300_NUM_2G_CCK_TARGET_POWERS];
+ struct cal_tgt_pow_legacy
+ calTargetPower2G[AR9300_NUM_2G_20_TARGET_POWERS];
+ struct cal_tgt_pow_ht
+ calTargetPower2GHT20[AR9300_NUM_2G_20_TARGET_POWERS];
+ struct cal_tgt_pow_ht
+ calTargetPower2GHT40[AR9300_NUM_2G_40_TARGET_POWERS];
+ u8 ctlIndex_2G[AR9300_NUM_CTLS_2G];
+ u8 ctl_freqbin_2G[AR9300_NUM_CTLS_2G][AR9300_NUM_BAND_EDGES_2G];
+ struct cal_ctl_data_2g ctlPowerData_2G[AR9300_NUM_CTLS_2G];
+ struct ar9300_modal_eep_header modalHeader5G;
+ struct ar9300_BaseExtension_2 base_ext2;
+ u8 calFreqPier5G[AR9300_NUM_5G_CAL_PIERS];
+ struct ar9300_cal_data_per_freq_op_loop
+ calPierData5G[AR9300_MAX_CHAINS][AR9300_NUM_5G_CAL_PIERS];
+ u8 calTarget_freqbin_5G[AR9300_NUM_5G_20_TARGET_POWERS];
+ u8 calTarget_freqbin_5GHT20[AR9300_NUM_5G_20_TARGET_POWERS];
+ u8 calTarget_freqbin_5GHT40[AR9300_NUM_5G_40_TARGET_POWERS];
+ struct cal_tgt_pow_legacy
+ calTargetPower5G[AR9300_NUM_5G_20_TARGET_POWERS];
+ struct cal_tgt_pow_ht
+ calTargetPower5GHT20[AR9300_NUM_5G_20_TARGET_POWERS];
+ struct cal_tgt_pow_ht
+ calTargetPower5GHT40[AR9300_NUM_5G_40_TARGET_POWERS];
+ u8 ctlIndex_5G[AR9300_NUM_CTLS_5G];
+ u8 ctl_freqbin_5G[AR9300_NUM_CTLS_5G][AR9300_NUM_BAND_EDGES_5G];
+ struct cal_ctl_data_5g ctlPowerData_5G[AR9300_NUM_CTLS_5G];
+} __attribute__((packed));
+
+s32 ar9003_hw_get_tx_gain_idx(struct ath_hw *ah);
+s32 ar9003_hw_get_rx_gain_idx(struct ath_hw *ah);
+
+u8 *ar9003_get_spur_chan_ptr(struct ath_hw *ah, int is_2ghz);
+
+unsigned int ar9003_get_paprd_scale_factor(struct ath_hw *ah,
+ struct ath9k_channel *chan);
+#endif
Code Review / kvmfornfv.git / blobdiff