--- /dev/null
+#
+# 1-wire slaves configuration
+#
+
+menu "1-wire Slaves"
+
+config W1_SLAVE_THERM
+ tristate "Thermal family implementation"
+ help
+ Say Y here if you want to connect 1-wire thermal sensors to your
+ wire.
+
+config W1_SLAVE_SMEM
+ tristate "Simple 64bit memory family implementation"
+ help
+ Say Y here if you want to connect 1-wire
+ simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire.
+
+config W1_SLAVE_DS2408
+ tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)"
+ help
+ Say Y here if you want to use a 1-wire
+ DS2408 8-Channel Addressable Switch device support
+
+config W1_SLAVE_DS2408_READBACK
+ bool "Read-back values written to DS2408's output register"
+ depends on W1_SLAVE_DS2408
+ default y
+ help
+ Enabling this will cause the driver to read back the values written
+ to the chip's output register in order to detect errors.
+
+ This is slower but useful when debugging chips and/or busses.
+
+config W1_SLAVE_DS2413
+ tristate "Dual Channel Addressable Switch 0x3a family support (DS2413)"
+ help
+ Say Y here if you want to use a 1-wire
+ DS2413 Dual Channel Addressable Switch device support
+
+config W1_SLAVE_DS2406
+ tristate "Dual Channel Addressable Switch 0x12 family support (DS2406)"
+ select CRC16
+ help
+ Say Y or M here if you want to use a 1-wire
+ DS2406 Dual Channel Addressable Switch. EPROM read/write
+ support for these devices is not implemented.
+
+config W1_SLAVE_DS2423
+ tristate "Counter 1-wire device (DS2423)"
+ select CRC16
+ help
+ If you enable this you can read the counter values available
+ in the DS2423 chipset from the w1_slave file under the
+ sys file system.
+
+ Say Y here if you want to use a 1-wire
+ counter family device (DS2423).
+
+config W1_SLAVE_DS2431
+ tristate "1kb EEPROM family support (DS2431)"
+ help
+ Say Y here if you want to use a 1-wire
+ 1kb EEPROM family device (DS2431)
+
+config W1_SLAVE_DS2433
+ tristate "4kb EEPROM family support (DS2433)"
+ help
+ Say Y here if you want to use a 1-wire
+ 4kb EEPROM family device (DS2433).
+
+config W1_SLAVE_DS2433_CRC
+ bool "Protect DS2433 data with a CRC16"
+ depends on W1_SLAVE_DS2433
+ select CRC16
+ help
+ Say Y here to protect DS2433 data with a CRC16.
+ Each block has 30 bytes of data and a two byte CRC16.
+ Full block writes are only allowed if the CRC is valid.
+
+config W1_SLAVE_DS2760
+ tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
+ help
+ If you enable this you will have the DS2760 battery monitor
+ chip support.
+
+ The battery monitor chip is used in many batteries/devices
+ as the one who is responsible for charging/discharging/monitoring
+ Li+ batteries.
+
+ If you are unsure, say N.
+
+config W1_SLAVE_DS2780
+ tristate "Dallas 2780 battery monitor chip"
+ help
+ If you enable this you will have the DS2780 battery monitor
+ chip support.
+
+ The battery monitor chip is used in many batteries/devices
+ as the one who is responsible for charging/discharging/monitoring
+ Li+ batteries.
+
+ If you are unsure, say N.
+
+config W1_SLAVE_DS2781
+ tristate "Dallas 2781 battery monitor chip"
+ help
+ If you enable this you will have the DS2781 battery monitor
+ chip support.
+
+ The battery monitor chip is used in many batteries/devices
+ as the one who is responsible for charging/discharging/monitoring
+ Li+ batteries.
+
+ If you are unsure, say N.
+
+config W1_SLAVE_DS28E04
+ tristate "4096-Bit Addressable 1-Wire EEPROM with PIO (DS28E04-100)"
+ select CRC16
+ help
+ If you enable this you will have the DS28E04-100
+ chip support.
+
+ Say Y here if you want to use a 1-wire
+ 4kb EEPROM with PIO family device (DS28E04).
+
+ If you are unsure, say N.
+
+config W1_SLAVE_BQ27000
+ tristate "BQ27000 slave support"
+ help
+ Say Y here if you want to use a hdq
+ bq27000 slave support.
+
+endmenu
Code Review / kvmfornfv.git / blobdiff