--- /dev/null
+/*
+ * Driver for PLX NET2272 USB device controller
+ *
+ * Copyright (C) 2005-2006 PLX Technology, Inc.
+ * Copyright (C) 2006-2011 Analog Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/prefetch.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/timer.h>
+#include <linux/usb.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+
+#include <asm/byteorder.h>
+#include <asm/unaligned.h>
+
+#include "net2272.h"
+
+#define DRIVER_DESC "PLX NET2272 USB Peripheral Controller"
+
+static const char driver_name[] = "net2272";
+static const char driver_vers[] = "2006 October 17/mainline";
+static const char driver_desc[] = DRIVER_DESC;
+
+static const char ep0name[] = "ep0";
+static const char * const ep_name[] = {
+ ep0name,
+ "ep-a", "ep-b", "ep-c",
+};
+
+#ifdef CONFIG_USB_NET2272_DMA
+/*
+ * use_dma: the NET2272 can use an external DMA controller.
+ * Note that since there is no generic DMA api, some functions,
+ * notably request_dma, start_dma, and cancel_dma will need to be
+ * modified for your platform's particular dma controller.
+ *
+ * If use_dma is disabled, pio will be used instead.
+ */
+static bool use_dma = 0;
+module_param(use_dma, bool, 0644);
+
+/*
+ * dma_ep: selects the endpoint for use with dma (1=ep-a, 2=ep-b)
+ * The NET2272 can only use dma for a single endpoint at a time.
+ * At some point this could be modified to allow either endpoint
+ * to take control of dma as it becomes available.
+ *
+ * Note that DMA should not be used on OUT endpoints unless it can
+ * be guaranteed that no short packets will arrive on an IN endpoint
+ * while the DMA operation is pending. Otherwise the OUT DMA will
+ * terminate prematurely (See NET2272 Errata 630-0213-0101)
+ */
+static ushort dma_ep = 1;
+module_param(dma_ep, ushort, 0644);
+
+/*
+ * dma_mode: net2272 dma mode setting (see LOCCTL1 definiton):
+ * mode 0 == Slow DREQ mode
+ * mode 1 == Fast DREQ mode
+ * mode 2 == Burst mode
+ */
+static ushort dma_mode = 2;
+module_param(dma_mode, ushort, 0644);
+#else
+#define use_dma 0
+#define dma_ep 1
+#define dma_mode 2
+#endif
+
+/*
+ * fifo_mode: net2272 buffer configuration:
+ * mode 0 == ep-{a,b,c} 512db each
+ * mode 1 == ep-a 1k, ep-{b,c} 512db
+ * mode 2 == ep-a 1k, ep-b 1k, ep-c 512db
+ * mode 3 == ep-a 1k, ep-b disabled, ep-c 512db
+ */
+static ushort fifo_mode = 0;
+module_param(fifo_mode, ushort, 0644);
+
+/*
+ * enable_suspend: When enabled, the driver will respond to
+ * USB suspend requests by powering down the NET2272. Otherwise,
+ * USB suspend requests will be ignored. This is acceptible for
+ * self-powered devices. For bus powered devices set this to 1.
+ */
+static ushort enable_suspend = 0;
+module_param(enable_suspend, ushort, 0644);
+
+static void assert_out_naking(struct net2272_ep *ep, const char *where)
+{
+ u8 tmp;
+
+#ifndef DEBUG
+ return;
+#endif
+
+ tmp = net2272_ep_read(ep, EP_STAT0);
+ if ((tmp & (1 << NAK_OUT_PACKETS)) == 0) {
+ dev_dbg(ep->dev->dev, "%s %s %02x !NAK\n",
+ ep->ep.name, where, tmp);
+ net2272_ep_write(ep, EP_RSPSET, 1 << ALT_NAK_OUT_PACKETS);
+ }
+}
+#define ASSERT_OUT_NAKING(ep) assert_out_naking(ep, __func__)
+
+static void stop_out_naking(struct net2272_ep *ep)
+{
+ u8 tmp = net2272_ep_read(ep, EP_STAT0);
+
+ if ((tmp & (1 << NAK_OUT_PACKETS)) != 0)
+ net2272_ep_write(ep, EP_RSPCLR, 1 << ALT_NAK_OUT_PACKETS);
+}
+
+#define PIPEDIR(bAddress) (usb_pipein(bAddress) ? "in" : "out")
+
+static char *type_string(u8 bmAttributes)
+{
+ switch ((bmAttributes) & USB_ENDPOINT_XFERTYPE_MASK) {
+ case USB_ENDPOINT_XFER_BULK: return "bulk";
+ case USB_ENDPOINT_XFER_ISOC: return "iso";
+ case USB_ENDPOINT_XFER_INT: return "intr";
+ default: return "control";
+ }
+}
+
+static char *buf_state_string(unsigned state)
+{
+ switch (state) {
+ case BUFF_FREE: return "free";
+ case BUFF_VALID: return "valid";
+ case BUFF_LCL: return "local";
+ case BUFF_USB: return "usb";
+ default: return "unknown";
+ }
+}
+
+static char *dma_mode_string(void)
+{
+ if (!use_dma)
+ return "PIO";
+ switch (dma_mode) {
+ case 0: return "SLOW DREQ";
+ case 1: return "FAST DREQ";
+ case 2: return "BURST";
+ default: return "invalid";
+ }
+}
+
+static void net2272_dequeue_all(struct net2272_ep *);
+static int net2272_kick_dma(struct net2272_ep *, struct net2272_request *);
+static int net2272_fifo_status(struct usb_ep *);
+
+static struct usb_ep_ops net2272_ep_ops;
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
+{
+ struct net2272 *dev;
+ struct net2272_ep *ep;
+ u32 max;
+ u8 tmp;
+ unsigned long flags;
+
+ ep = container_of(_ep, struct net2272_ep, ep);
+ if (!_ep || !desc || ep->desc || _ep->name == ep0name
+ || desc->bDescriptorType != USB_DT_ENDPOINT)
+ return -EINVAL;
+ dev = ep->dev;
+ if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN)
+ return -ESHUTDOWN;
+
+ max = usb_endpoint_maxp(desc) & 0x1fff;
+
+ spin_lock_irqsave(&dev->lock, flags);
+ _ep->maxpacket = max & 0x7fff;
+ ep->desc = desc;
+
+ /* net2272_ep_reset() has already been called */
+ ep->stopped = 0;
+ ep->wedged = 0;
+
+ /* set speed-dependent max packet */
+ net2272_ep_write(ep, EP_MAXPKT0, max & 0xff);
+ net2272_ep_write(ep, EP_MAXPKT1, (max & 0xff00) >> 8);
+
+ /* set type, direction, address; reset fifo counters */
+ net2272_ep_write(ep, EP_STAT1, 1 << BUFFER_FLUSH);
+ tmp = usb_endpoint_type(desc);
+ if (usb_endpoint_xfer_bulk(desc)) {
+ /* catch some particularly blatant driver bugs */
+ if ((dev->gadget.speed == USB_SPEED_HIGH && max != 512) ||
+ (dev->gadget.speed == USB_SPEED_FULL && max > 64)) {
+ spin_unlock_irqrestore(&dev->lock, flags);
+ return -ERANGE;
+ }
+ }
+ ep->is_iso = usb_endpoint_xfer_isoc(desc) ? 1 : 0;
+ tmp <<= ENDPOINT_TYPE;
+ tmp |= ((desc->bEndpointAddress & 0x0f) << ENDPOINT_NUMBER);
+ tmp |= usb_endpoint_dir_in(desc) << ENDPOINT_DIRECTION;
+ tmp |= (1 << ENDPOINT_ENABLE);
+
+ /* for OUT transfers, block the rx fifo until a read is posted */
+ ep->is_in = usb_endpoint_dir_in(desc);
+ if (!ep->is_in)
+ net2272_ep_write(ep, EP_RSPSET, 1 << ALT_NAK_OUT_PACKETS);
+
+ net2272_ep_write(ep, EP_CFG, tmp);
+
+ /* enable irqs */
+ tmp = (1 << ep->num) | net2272_read(dev, IRQENB0);
+ net2272_write(dev, IRQENB0, tmp);
+
+ tmp = (1 << DATA_PACKET_RECEIVED_INTERRUPT_ENABLE)
+ | (1 << DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE)
+ | net2272_ep_read(ep, EP_IRQENB);
+ net2272_ep_write(ep, EP_IRQENB, tmp);
+
+ tmp = desc->bEndpointAddress;
+ dev_dbg(dev->dev, "enabled %s (ep%d%s-%s) max %04x cfg %02x\n",
+ _ep->name, tmp & 0x0f, PIPEDIR(tmp),
+ type_string(desc->bmAttributes), max,
+ net2272_ep_read(ep, EP_CFG));
+
+ spin_unlock_irqrestore(&dev->lock, flags);
+ return 0;
+}
+
+static void net2272_ep_reset(struct net2272_ep *ep)
+{
+ u8 tmp;
+
+ ep->desc = NULL;
+ INIT_LIST_HEAD(&ep->queue);
+
+ usb_ep_set_maxpacket_limit(&ep->ep, ~0);
+ ep->ep.ops = &net2272_ep_ops;
+
+ /* disable irqs, endpoint */
+ net2272_ep_write(ep, EP_IRQENB, 0);
+
+ /* init to our chosen defaults, notably so that we NAK OUT
+ * packets until the driver queues a read.
+ */
+ tmp = (1 << NAK_OUT_PACKETS_MODE) | (1 << ALT_NAK_OUT_PACKETS);
+ net2272_ep_write(ep, EP_RSPSET, tmp);
+
+ tmp = (1 << INTERRUPT_MODE) | (1 << HIDE_STATUS_PHASE);
+ if (ep->num != 0)
+ tmp |= (1 << ENDPOINT_TOGGLE) | (1 << ENDPOINT_HALT);
+
+ net2272_ep_write(ep, EP_RSPCLR, tmp);
+
+ /* scrub most status bits, and flush any fifo state */
+ net2272_ep_write(ep, EP_STAT0,
+ (1 << DATA_IN_TOKEN_INTERRUPT)
+ | (1 << DATA_OUT_TOKEN_INTERRUPT)
+ | (1 << DATA_PACKET_TRANSMITTED_INTERRUPT)
+ | (1 << DATA_PACKET_RECEIVED_INTERRUPT)
+ | (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT));
+
+ net2272_ep_write(ep, EP_STAT1,
+ (1 << TIMEOUT)
+ | (1 << USB_OUT_ACK_SENT)
+ | (1 << USB_OUT_NAK_SENT)
+ | (1 << USB_IN_ACK_RCVD)
+ | (1 << USB_IN_NAK_SENT)
+ | (1 << USB_STALL_SENT)
+ | (1 << LOCAL_OUT_ZLP)
+ | (1 << BUFFER_FLUSH));
+
+ /* fifo size is handled seperately */
+}
+
+static int net2272_disable(struct usb_ep *_ep)
+{
+ struct net2272_ep *ep;
+ unsigned long flags;
+
+ ep = container_of(_ep, struct net2272_ep, ep);
+ if (!_ep || !ep->desc || _ep->name == ep0name)
+ return -EINVAL;
+
+ spin_lock_irqsave(&ep->dev->lock, flags);
+ net2272_dequeue_all(ep);
+ net2272_ep_reset(ep);
+
+ dev_vdbg(ep->dev->dev, "disabled %s\n", _ep->name);
+
+ spin_unlock_irqrestore(&ep->dev->lock, flags);
+ return 0;
+}
+
+/*---------------------------------------------------------------------------*/
+
+static struct usb_request *
+net2272_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags)
+{
+ struct net2272_ep *ep;
+ struct net2272_request *req;
+
+ if (!_ep)
+ return NULL;
+ ep = container_of(_ep, struct net2272_ep, ep);
+
+ req = kzalloc(sizeof(*req), gfp_flags);
+ if (!req)
+ return NULL;
+
+ INIT_LIST_HEAD(&req->queue);
+
+ return &req->req;
+}
+
+static void
+net2272_free_request(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct net2272_ep *ep;
+ struct net2272_request *req;
+
+ ep = container_of(_ep, struct net2272_ep, ep);
+ if (!_ep || !_req)
+ return;
+
+ req = container_of(_req, struct net2272_request, req);
+ WARN_ON(!list_empty(&req->queue));
+ kfree(req);
+}
+
+static void
+net2272_done(struct net2272_ep *ep, struct net2272_request *req, int status)
+{
+ struct net2272 *dev;
+ unsigned stopped = ep->stopped;
+
+ if (ep->num == 0) {
+ if (ep->dev->protocol_stall) {
+ ep->stopped = 1;
+ set_halt(ep);
+ }
+ allow_status(ep);
+ }
+
+ list_del_init(&req->queue);
+
+ if (req->req.status == -EINPROGRESS)
+ req->req.status = status;
+ else
+ status = req->req.status;
+
+ dev = ep->dev;
+ if (use_dma && ep->dma)
+ usb_gadget_unmap_request(&dev->gadget, &req->req,
+ ep->is_in);
+
+ if (status && status != -ESHUTDOWN)
+ dev_vdbg(dev->dev, "complete %s req %p stat %d len %u/%u buf %p\n",
+ ep->ep.name, &req->req, status,
+ req->req.actual, req->req.length, req->req.buf);
+
+ /* don't modify queue heads during completion callback */
+ ep->stopped = 1;
+ spin_unlock(&dev->lock);
+ usb_gadget_giveback_request(&ep->ep, &req->req);
+ spin_lock(&dev->lock);
+ ep->stopped = stopped;
+}
+
+static int
+net2272_write_packet(struct net2272_ep *ep, u8 *buf,
+ struct net2272_request *req, unsigned max)
+{
+ u16 __iomem *ep_data = net2272_reg_addr(ep->dev, EP_DATA);
+ u16 *bufp;
+ unsigned length, count;
+ u8 tmp;
+
+ length = min(req->req.length - req->req.actual, max);
+ req->req.actual += length;
+
+ dev_vdbg(ep->dev->dev, "write packet %s req %p max %u len %u avail %u\n",
+ ep->ep.name, req, max, length,
+ (net2272_ep_read(ep, EP_AVAIL1) << 8) | net2272_ep_read(ep, EP_AVAIL0));
+
+ count = length;
+ bufp = (u16 *)buf;
+
+ while (likely(count >= 2)) {
+ /* no byte-swap required; chip endian set during init */
+ writew(*bufp++, ep_data);
+ count -= 2;
+ }
+ buf = (u8 *)bufp;
+
+ /* write final byte by placing the NET2272 into 8-bit mode */
+ if (unlikely(count)) {
+ tmp = net2272_read(ep->dev, LOCCTL);
+ net2272_write(ep->dev, LOCCTL, tmp & ~(1 << DATA_WIDTH));
+ writeb(*buf, ep_data);
+ net2272_write(ep->dev, LOCCTL, tmp);
+ }
+ return length;
+}
+
+/* returns: 0: still running, 1: completed, negative: errno */
+static int
+net2272_write_fifo(struct net2272_ep *ep, struct net2272_request *req)
+{
+ u8 *buf;
+ unsigned count, max;
+ int status;
+
+ dev_vdbg(ep->dev->dev, "write_fifo %s actual %d len %d\n",
+ ep->ep.name, req->req.actual, req->req.length);
+
+ /*
+ * Keep loading the endpoint until the final packet is loaded,
+ * or the endpoint buffer is full.
+ */
+ top:
+ /*
+ * Clear interrupt status
+ * - Packet Transmitted interrupt will become set again when the
+ * host successfully takes another packet
+ */
+ net2272_ep_write(ep, EP_STAT0, (1 << DATA_PACKET_TRANSMITTED_INTERRUPT));
+ while (!(net2272_ep_read(ep, EP_STAT0) & (1 << BUFFER_FULL))) {
+ buf = req->req.buf + req->req.actual;
+ prefetch(buf);
+
+ /* force pagesel */
+ net2272_ep_read(ep, EP_STAT0);
+
+ max = (net2272_ep_read(ep, EP_AVAIL1) << 8) |
+ (net2272_ep_read(ep, EP_AVAIL0));
+
+ if (max < ep->ep.maxpacket)
+ max = (net2272_ep_read(ep, EP_AVAIL1) << 8)
+ | (net2272_ep_read(ep, EP_AVAIL0));
+
+ count = net2272_write_packet(ep, buf, req, max);
+ /* see if we are done */
+ if (req->req.length == req->req.actual) {
+ /* validate short or zlp packet */
+ if (count < ep->ep.maxpacket)
+ set_fifo_bytecount(ep, 0);
+ net2272_done(ep, req, 0);
+
+ if (!list_empty(&ep->queue)) {
+ req = list_entry(ep->queue.next,
+ struct net2272_request,
+ queue);
+ status = net2272_kick_dma(ep, req);
+
+ if (status < 0)
+ if ((net2272_ep_read(ep, EP_STAT0)
+ & (1 << BUFFER_EMPTY)))
+ goto top;
+ }
+ return 1;
+ }
+ net2272_ep_write(ep, EP_STAT0, (1 << DATA_PACKET_TRANSMITTED_INTERRUPT));
+ }
+ return 0;
+}
+
+static void
+net2272_out_flush(struct net2272_ep *ep)
+{
+ ASSERT_OUT_NAKING(ep);
+
+ net2272_ep_write(ep, EP_STAT0, (1 << DATA_OUT_TOKEN_INTERRUPT)
+ | (1 << DATA_PACKET_RECEIVED_INTERRUPT));
+ net2272_ep_write(ep, EP_STAT1, 1 << BUFFER_FLUSH);
+}
+
+static int
+net2272_read_packet(struct net2272_ep *ep, u8 *buf,
+ struct net2272_request *req, unsigned avail)
+{
+ u16 __iomem *ep_data = net2272_reg_addr(ep->dev, EP_DATA);
+ unsigned is_short;
+ u16 *bufp;
+
+ req->req.actual += avail;
+
+ dev_vdbg(ep->dev->dev, "read packet %s req %p len %u avail %u\n",
+ ep->ep.name, req, avail,
+ (net2272_ep_read(ep, EP_AVAIL1) << 8) | net2272_ep_read(ep, EP_AVAIL0));
+
+ is_short = (avail < ep->ep.maxpacket);
+
+ if (unlikely(avail == 0)) {
+ /* remove any zlp from the buffer */
+ (void)readw(ep_data);
+ return is_short;
+ }
+
+ /* Ensure we get the final byte */
+ if (unlikely(avail % 2))
+ avail++;
+ bufp = (u16 *)buf;
+
+ do {
+ *bufp++ = readw(ep_data);
+ avail -= 2;
+ } while (avail);
+
+ /*
+ * To avoid false endpoint available race condition must read
+ * ep stat0 twice in the case of a short transfer
+ */
+ if (net2272_ep_read(ep, EP_STAT0) & (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT))
+ net2272_ep_read(ep, EP_STAT0);
+
+ return is_short;
+}
+
+static int
+net2272_read_fifo(struct net2272_ep *ep, struct net2272_request *req)
+{
+ u8 *buf;
+ unsigned is_short;
+ int count;
+ int tmp;
+ int cleanup = 0;
+ int status = -1;
+
+ dev_vdbg(ep->dev->dev, "read_fifo %s actual %d len %d\n",
+ ep->ep.name, req->req.actual, req->req.length);
+
+ top:
+ do {
+ buf = req->req.buf + req->req.actual;
+ prefetchw(buf);
+
+ count = (net2272_ep_read(ep, EP_AVAIL1) << 8)
+ | net2272_ep_read(ep, EP_AVAIL0);
+
+ net2272_ep_write(ep, EP_STAT0,
+ (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT) |
+ (1 << DATA_PACKET_RECEIVED_INTERRUPT));
+
+ tmp = req->req.length - req->req.actual;
+
+ if (count > tmp) {
+ if ((tmp % ep->ep.maxpacket) != 0) {
+ dev_err(ep->dev->dev,
+ "%s out fifo %d bytes, expected %d\n",
+ ep->ep.name, count, tmp);
+ cleanup = 1;
+ }
+ count = (tmp > 0) ? tmp : 0;
+ }
+
+ is_short = net2272_read_packet(ep, buf, req, count);
+
+ /* completion */
+ if (unlikely(cleanup || is_short ||
+ ((req->req.actual == req->req.length)
+ && !req->req.zero))) {
+
+ if (cleanup) {
+ net2272_out_flush(ep);
+ net2272_done(ep, req, -EOVERFLOW);
+ } else
+ net2272_done(ep, req, 0);
+
+ /* re-initialize endpoint transfer registers
+ * otherwise they may result in erroneous pre-validation
+ * for subsequent control reads
+ */
+ if (unlikely(ep->num == 0)) {
+ net2272_ep_write(ep, EP_TRANSFER2, 0);
+ net2272_ep_write(ep, EP_TRANSFER1, 0);
+ net2272_ep_write(ep, EP_TRANSFER0, 0);
+ }
+
+ if (!list_empty(&ep->queue)) {
+ req = list_entry(ep->queue.next,
+ struct net2272_request, queue);
+ status = net2272_kick_dma(ep, req);
+ if ((status < 0) &&
+ !(net2272_ep_read(ep, EP_STAT0) & (1 << BUFFER_EMPTY)))
+ goto top;
+ }
+ return 1;
+ }
+ } while (!(net2272_ep_read(ep, EP_STAT0) & (1 << BUFFER_EMPTY)));
+
+ return 0;
+}
+
+static void
+net2272_pio_advance(struct net2272_ep *ep)
+{
+ struct net2272_request *req;
+
+ if (unlikely(list_empty(&ep->queue)))
+ return;
+
+ req = list_entry(ep->queue.next, struct net2272_request, queue);
+ (ep->is_in ? net2272_write_fifo : net2272_read_fifo)(ep, req);
+}
+
+/* returns 0 on success, else negative errno */
+static int
+net2272_request_dma(struct net2272 *dev, unsigned ep, u32 buf,
+ unsigned len, unsigned dir)
+{
+ dev_vdbg(dev->dev, "request_dma ep %d buf %08x len %d dir %d\n",
+ ep, buf, len, dir);
+
+ /* The NET2272 only supports a single dma channel */
+ if (dev->dma_busy)
+ return -EBUSY;
+ /*
+ * EP_TRANSFER (used to determine the number of bytes received
+ * in an OUT transfer) is 24 bits wide; don't ask for more than that.
+ */
+ if ((dir == 1) && (len > 0x1000000))
+ return -EINVAL;
+
+ dev->dma_busy = 1;
+
+ /* initialize platform's dma */
+#ifdef CONFIG_PCI
+ /* NET2272 addr, buffer addr, length, etc. */
+ switch (dev->dev_id) {
+ case PCI_DEVICE_ID_RDK1:
+ /* Setup PLX 9054 DMA mode */
+ writel((1 << LOCAL_BUS_WIDTH) |
+ (1 << TA_READY_INPUT_ENABLE) |
+ (0 << LOCAL_BURST_ENABLE) |
+ (1 << DONE_INTERRUPT_ENABLE) |
+ (1 << LOCAL_ADDRESSING_MODE) |
+ (1 << DEMAND_MODE) |
+ (1 << DMA_EOT_ENABLE) |
+ (1 << FAST_SLOW_TERMINATE_MODE_SELECT) |
+ (1 << DMA_CHANNEL_INTERRUPT_SELECT),
+ dev->rdk1.plx9054_base_addr + DMAMODE0);
+
+ writel(0x100000, dev->rdk1.plx9054_base_addr + DMALADR0);
+ writel(buf, dev->rdk1.plx9054_base_addr + DMAPADR0);
+ writel(len, dev->rdk1.plx9054_base_addr + DMASIZ0);
+ writel((dir << DIRECTION_OF_TRANSFER) |
+ (1 << INTERRUPT_AFTER_TERMINAL_COUNT),
+ dev->rdk1.plx9054_base_addr + DMADPR0);
+ writel((1 << LOCAL_DMA_CHANNEL_0_INTERRUPT_ENABLE) |
+ readl(dev->rdk1.plx9054_base_addr + INTCSR),
+ dev->rdk1.plx9054_base_addr + INTCSR);
+
+ break;
+ }
+#endif
+
+ net2272_write(dev, DMAREQ,
+ (0 << DMA_BUFFER_VALID) |
+ (1 << DMA_REQUEST_ENABLE) |
+ (1 << DMA_CONTROL_DACK) |
+ (dev->dma_eot_polarity << EOT_POLARITY) |
+ (dev->dma_dack_polarity << DACK_POLARITY) |
+ (dev->dma_dreq_polarity << DREQ_POLARITY) |
+ ((ep >> 1) << DMA_ENDPOINT_SELECT));
+
+ (void) net2272_read(dev, SCRATCH);
+
+ return 0;
+}
+
+static void
+net2272_start_dma(struct net2272 *dev)
+{
+ /* start platform's dma controller */
+#ifdef CONFIG_PCI
+ switch (dev->dev_id) {
+ case PCI_DEVICE_ID_RDK1:
+ writeb((1 << CHANNEL_ENABLE) | (1 << CHANNEL_START),
+ dev->rdk1.plx9054_base_addr + DMACSR0);
+ break;
+ }
+#endif
+}
+
+/* returns 0 on success, else negative errno */
+static int
+net2272_kick_dma(struct net2272_ep *ep, struct net2272_request *req)
+{
+ unsigned size;
+ u8 tmp;
+
+ if (!use_dma || (ep->num < 1) || (ep->num > 2) || !ep->dma)
+ return -EINVAL;
+
+ /* don't use dma for odd-length transfers
+ * otherwise, we'd need to deal with the last byte with pio
+ */
+ if (req->req.length & 1)
+ return -EINVAL;
+
+ dev_vdbg(ep->dev->dev, "kick_dma %s req %p dma %08llx\n",
+ ep->ep.name, req, (unsigned long long) req->req.dma);
+
+ net2272_ep_write(ep, EP_RSPSET, 1 << ALT_NAK_OUT_PACKETS);
+
+ /* The NET2272 can only use DMA on one endpoint at a time */
+ if (ep->dev->dma_busy)
+ return -EBUSY;
+
+ /* Make sure we only DMA an even number of bytes (we'll use
+ * pio to complete the transfer)
+ */
+ size = req->req.length;
+ size &= ~1;
+
+ /* device-to-host transfer */
+ if (ep->is_in) {
+ /* initialize platform's dma controller */
+ if (net2272_request_dma(ep->dev, ep->num, req->req.dma, size, 0))
+ /* unable to obtain DMA channel; return error and use pio mode */
+ return -EBUSY;
+ req->req.actual += size;
+
+ /* host-to-device transfer */
+ } else {
+ tmp = net2272_ep_read(ep, EP_STAT0);
+
+ /* initialize platform's dma controller */
+ if (net2272_request_dma(ep->dev, ep->num, req->req.dma, size, 1))
+ /* unable to obtain DMA channel; return error and use pio mode */
+ return -EBUSY;
+
+ if (!(tmp & (1 << BUFFER_EMPTY)))
+ ep->not_empty = 1;
+ else
+ ep->not_empty = 0;
+
+
+ /* allow the endpoint's buffer to fill */
+ net2272_ep_write(ep, EP_RSPCLR, 1 << ALT_NAK_OUT_PACKETS);
+
+ /* this transfer completed and data's already in the fifo
+ * return error so pio gets used.
+ */
+ if (tmp & (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT)) {
+
+ /* deassert dreq */
+ net2272_write(ep->dev, DMAREQ,
+ (0 << DMA_BUFFER_VALID) |
+ (0 << DMA_REQUEST_ENABLE) |
+ (1 << DMA_CONTROL_DACK) |
+ (ep->dev->dma_eot_polarity << EOT_POLARITY) |
+ (ep->dev->dma_dack_polarity << DACK_POLARITY) |
+ (ep->dev->dma_dreq_polarity << DREQ_POLARITY) |
+ ((ep->num >> 1) << DMA_ENDPOINT_SELECT));
+
+ return -EBUSY;
+ }
+ }
+
+ /* Don't use per-packet interrupts: use dma interrupts only */
+ net2272_ep_write(ep, EP_IRQENB, 0);
+
+ net2272_start_dma(ep->dev);
+
+ return 0;
+}
+
+static void net2272_cancel_dma(struct net2272 *dev)
+{
+#ifdef CONFIG_PCI
+ switch (dev->dev_id) {
+ case PCI_DEVICE_ID_RDK1:
+ writeb(0, dev->rdk1.plx9054_base_addr + DMACSR0);
+ writeb(1 << CHANNEL_ABORT, dev->rdk1.plx9054_base_addr + DMACSR0);
+ while (!(readb(dev->rdk1.plx9054_base_addr + DMACSR0) &
+ (1 << CHANNEL_DONE)))
+ continue; /* wait for dma to stabalize */
+
+ /* dma abort generates an interrupt */
+ writeb(1 << CHANNEL_CLEAR_INTERRUPT,
+ dev->rdk1.plx9054_base_addr + DMACSR0);
+ break;
+ }
+#endif
+
+ dev->dma_busy = 0;
+}
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
+{
+ struct net2272_request *req;
+ struct net2272_ep *ep;
+ struct net2272 *dev;
+ unsigned long flags;
+ int status = -1;
+ u8 s;
+
+ req = container_of(_req, struct net2272_request, req);
+ if (!_req || !_req->complete || !_req->buf
+ || !list_empty(&req->queue))
+ return -EINVAL;
+ ep = container_of(_ep, struct net2272_ep, ep);
+ if (!_ep || (!ep->desc && ep->num != 0))
+ return -EINVAL;
+ dev = ep->dev;
+ if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN)
+ return -ESHUTDOWN;
+
+ /* set up dma mapping in case the caller didn't */
+ if (use_dma && ep->dma) {
+ status = usb_gadget_map_request(&dev->gadget, _req,
+ ep->is_in);
+ if (status)
+ return status;
+ }
+
+ dev_vdbg(dev->dev, "%s queue req %p, len %d buf %p dma %08llx %s\n",
+ _ep->name, _req, _req->length, _req->buf,
+ (unsigned long long) _req->dma, _req->zero ? "zero" : "!zero");
+
+ spin_lock_irqsave(&dev->lock, flags);
+
+ _req->status = -EINPROGRESS;
+ _req->actual = 0;
+
+ /* kickstart this i/o queue? */
+ if (list_empty(&ep->queue) && !ep->stopped) {
+ /* maybe there's no control data, just status ack */
+ if (ep->num == 0 && _req->length == 0) {
+ net2272_done(ep, req, 0);
+ dev_vdbg(dev->dev, "%s status ack\n", ep->ep.name);
+ goto done;
+ }
+
+ /* Return zlp, don't let it block subsequent packets */
+ s = net2272_ep_read(ep, EP_STAT0);
+ if (s & (1 << BUFFER_EMPTY)) {
+ /* Buffer is empty check for a blocking zlp, handle it */
+ if ((s & (1 << NAK_OUT_PACKETS)) &&
+ net2272_ep_read(ep, EP_STAT1) & (1 << LOCAL_OUT_ZLP)) {
+ dev_dbg(dev->dev, "WARNING: returning ZLP short packet termination!\n");
+ /*
+ * Request is going to terminate with a short packet ...
+ * hope the client is ready for it!
+ */
+ status = net2272_read_fifo(ep, req);
+ /* clear short packet naking */
+ net2272_ep_write(ep, EP_STAT0, (1 << NAK_OUT_PACKETS));
+ goto done;
+ }
+ }
+
+ /* try dma first */
+ status = net2272_kick_dma(ep, req);
+
+ if (status < 0) {
+ /* dma failed (most likely in use by another endpoint)
+ * fallback to pio
+ */
+ status = 0;
+
+ if (ep->is_in)
+ status = net2272_write_fifo(ep, req);
+ else {
+ s = net2272_ep_read(ep, EP_STAT0);
+ if ((s & (1 << BUFFER_EMPTY)) == 0)
+ status = net2272_read_fifo(ep, req);
+ }
+
+ if (unlikely(status != 0)) {
+ if (status > 0)
+ status = 0;
+ req = NULL;
+ }
+ }
+ }
+ if (likely(req))
+ list_add_tail(&req->queue, &ep->queue);
+
+ if (likely(!list_empty(&ep->queue)))
+ net2272_ep_write(ep, EP_RSPCLR, 1 << ALT_NAK_OUT_PACKETS);
+ done:
+ spin_unlock_irqrestore(&dev->lock, flags);
+
+ return 0;
+}
+
+/* dequeue ALL requests */
+static void
+net2272_dequeue_all(struct net2272_ep *ep)
+{
+ struct net2272_request *req;
+
+ /* called with spinlock held */
+ ep->stopped = 1;
+
+ while (!list_empty(&ep->queue)) {
+ req = list_entry(ep->queue.next,
+ struct net2272_request,
+ queue);
+ net2272_done(ep, req, -ESHUTDOWN);
+ }
+}
+
+/* dequeue JUST ONE request */
+static int
+net2272_dequeue(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct net2272_ep *ep;
+ struct net2272_request *req;
+ unsigned long flags;
+ int stopped;
+
+ ep = container_of(_ep, struct net2272_ep, ep);
+ if (!_ep || (!ep->desc && ep->num != 0) || !_req)
+ return -EINVAL;
+
+ spin_lock_irqsave(&ep->dev->lock, flags);
+ stopped = ep->stopped;
+ ep->stopped = 1;
+
+ /* make sure it's still queued on this endpoint */
+ list_for_each_entry(req, &ep->queue, queue) {
+ if (&req->req == _req)
+ break;
+ }
+ if (&req->req != _req) {
+ spin_unlock_irqrestore(&ep->dev->lock, flags);
+ return -EINVAL;
+ }
+
+ /* queue head may be partially complete */
+ if (ep->queue.next == &req->queue) {
+ dev_dbg(ep->dev->dev, "unlink (%s) pio\n", _ep->name);
+ net2272_done(ep, req, -ECONNRESET);
+ }
+ req = NULL;
+ ep->stopped = stopped;
+
+ spin_unlock_irqrestore(&ep->dev->lock, flags);
+ return 0;
+}
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_set_halt_and_wedge(struct usb_ep *_ep, int value, int wedged)
+{
+ struct net2272_ep *ep;
+ unsigned long flags;
+ int ret = 0;
+
+ ep = container_of(_ep, struct net2272_ep, ep);
+ if (!_ep || (!ep->desc && ep->num != 0))
+ return -EINVAL;
+ if (!ep->dev->driver || ep->dev->gadget.speed == USB_SPEED_UNKNOWN)
+ return -ESHUTDOWN;
+ if (ep->desc /* not ep0 */ && usb_endpoint_xfer_isoc(ep->desc))
+ return -EINVAL;
+
+ spin_lock_irqsave(&ep->dev->lock, flags);
+ if (!list_empty(&ep->queue))
+ ret = -EAGAIN;
+ else if (ep->is_in && value && net2272_fifo_status(_ep) != 0)
+ ret = -EAGAIN;
+ else {
+ dev_vdbg(ep->dev->dev, "%s %s %s\n", _ep->name,
+ value ? "set" : "clear",
+ wedged ? "wedge" : "halt");
+ /* set/clear */
+ if (value) {
+ if (ep->num == 0)
+ ep->dev->protocol_stall = 1;
+ else
+ set_halt(ep);
+ if (wedged)
+ ep->wedged = 1;
+ } else {
+ clear_halt(ep);
+ ep->wedged = 0;
+ }
+ }
+ spin_unlock_irqrestore(&ep->dev->lock, flags);
+
+ return ret;
+}
+
+static int
+net2272_set_halt(struct usb_ep *_ep, int value)
+{
+ return net2272_set_halt_and_wedge(_ep, value, 0);
+}
+
+static int
+net2272_set_wedge(struct usb_ep *_ep)
+{
+ if (!_ep || _ep->name == ep0name)
+ return -EINVAL;
+ return net2272_set_halt_and_wedge(_ep, 1, 1);
+}
+
+static int
+net2272_fifo_status(struct usb_ep *_ep)
+{
+ struct net2272_ep *ep;
+ u16 avail;
+
+ ep = container_of(_ep, struct net2272_ep, ep);
+ if (!_ep || (!ep->desc && ep->num != 0))
+ return -ENODEV;
+ if (!ep->dev->driver || ep->dev->gadget.speed == USB_SPEED_UNKNOWN)
+ return -ESHUTDOWN;
+
+ avail = net2272_ep_read(ep, EP_AVAIL1) << 8;
+ avail |= net2272_ep_read(ep, EP_AVAIL0);
+ if (avail > ep->fifo_size)
+ return -EOVERFLOW;
+ if (ep->is_in)
+ avail = ep->fifo_size - avail;
+ return avail;
+}
+
+static void
+net2272_fifo_flush(struct usb_ep *_ep)
+{
+ struct net2272_ep *ep;
+
+ ep = container_of(_ep, struct net2272_ep, ep);
+ if (!_ep || (!ep->desc && ep->num != 0))
+ return;
+ if (!ep->dev->driver || ep->dev->gadget.speed == USB_SPEED_UNKNOWN)
+ return;
+
+ net2272_ep_write(ep, EP_STAT1, 1 << BUFFER_FLUSH);
+}
+
+static struct usb_ep_ops net2272_ep_ops = {
+ .enable = net2272_enable,
+ .disable = net2272_disable,
+
+ .alloc_request = net2272_alloc_request,
+ .free_request = net2272_free_request,
+
+ .queue = net2272_queue,
+ .dequeue = net2272_dequeue,
+
+ .set_halt = net2272_set_halt,
+ .set_wedge = net2272_set_wedge,
+ .fifo_status = net2272_fifo_status,
+ .fifo_flush = net2272_fifo_flush,
+};
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_get_frame(struct usb_gadget *_gadget)
+{
+ struct net2272 *dev;
+ unsigned long flags;
+ u16 ret;
+
+ if (!_gadget)
+ return -ENODEV;
+ dev = container_of(_gadget, struct net2272, gadget);
+ spin_lock_irqsave(&dev->lock, flags);
+
+ ret = net2272_read(dev, FRAME1) << 8;
+ ret |= net2272_read(dev, FRAME0);
+
+ spin_unlock_irqrestore(&dev->lock, flags);
+ return ret;
+}
+
+static int
+net2272_wakeup(struct usb_gadget *_gadget)
+{
+ struct net2272 *dev;
+ u8 tmp;
+ unsigned long flags;
+
+ if (!_gadget)
+ return 0;
+ dev = container_of(_gadget, struct net2272, gadget);
+
+ spin_lock_irqsave(&dev->lock, flags);
+ tmp = net2272_read(dev, USBCTL0);
+ if (tmp & (1 << IO_WAKEUP_ENABLE))
+ net2272_write(dev, USBCTL1, (1 << GENERATE_RESUME));
+
+ spin_unlock_irqrestore(&dev->lock, flags);
+
+ return 0;
+}
+
+static int
+net2272_set_selfpowered(struct usb_gadget *_gadget, int value)
+{
+ if (!_gadget)
+ return -ENODEV;
+
+ _gadget->is_selfpowered = (value != 0);
+
+ return 0;
+}
+
+static int
+net2272_pullup(struct usb_gadget *_gadget, int is_on)
+{
+ struct net2272 *dev;
+ u8 tmp;
+ unsigned long flags;
+
+ if (!_gadget)
+ return -ENODEV;
+ dev = container_of(_gadget, struct net2272, gadget);
+
+ spin_lock_irqsave(&dev->lock, flags);
+ tmp = net2272_read(dev, USBCTL0);
+ dev->softconnect = (is_on != 0);
+ if (is_on)
+ tmp |= (1 << USB_DETECT_ENABLE);
+ else
+ tmp &= ~(1 << USB_DETECT_ENABLE);
+ net2272_write(dev, USBCTL0, tmp);
+ spin_unlock_irqrestore(&dev->lock, flags);
+
+ return 0;
+}
+
+static int net2272_start(struct usb_gadget *_gadget,
+ struct usb_gadget_driver *driver);
+static int net2272_stop(struct usb_gadget *_gadget);
+
+static const struct usb_gadget_ops net2272_ops = {
+ .get_frame = net2272_get_frame,
+ .wakeup = net2272_wakeup,
+ .set_selfpowered = net2272_set_selfpowered,
+ .pullup = net2272_pullup,
+ .udc_start = net2272_start,
+ .udc_stop = net2272_stop,
+};
+
+/*---------------------------------------------------------------------------*/
+
+static ssize_t
+registers_show(struct device *_dev, struct device_attribute *attr, char *buf)
+{
+ struct net2272 *dev;
+ char *next;
+ unsigned size, t;
+ unsigned long flags;
+ u8 t1, t2;
+ int i;
+ const char *s;
+
+ dev = dev_get_drvdata(_dev);
+ next = buf;
+ size = PAGE_SIZE;
+ spin_lock_irqsave(&dev->lock, flags);
+
+ if (dev->driver)
+ s = dev->driver->driver.name;
+ else
+ s = "(none)";
+
+ /* Main Control Registers */
+ t = scnprintf(next, size, "%s version %s,"
+ "chiprev %02x, locctl %02x\n"
+ "irqenb0 %02x irqenb1 %02x "
+ "irqstat0 %02x irqstat1 %02x\n",
+ driver_name, driver_vers, dev->chiprev,
+ net2272_read(dev, LOCCTL),
+ net2272_read(dev, IRQENB0),
+ net2272_read(dev, IRQENB1),
+ net2272_read(dev, IRQSTAT0),
+ net2272_read(dev, IRQSTAT1));
+ size -= t;
+ next += t;
+
+ /* DMA */
+ t1 = net2272_read(dev, DMAREQ);
+ t = scnprintf(next, size, "\ndmareq %02x: %s %s%s%s%s\n",
+ t1, ep_name[(t1 & 0x01) + 1],
+ t1 & (1 << DMA_CONTROL_DACK) ? "dack " : "",
+ t1 & (1 << DMA_REQUEST_ENABLE) ? "reqenb " : "",
+ t1 & (1 << DMA_REQUEST) ? "req " : "",
+ t1 & (1 << DMA_BUFFER_VALID) ? "valid " : "");
+ size -= t;
+ next += t;
+
+ /* USB Control Registers */
+ t1 = net2272_read(dev, USBCTL1);
+ if (t1 & (1 << VBUS_PIN)) {
+ if (t1 & (1 << USB_HIGH_SPEED))
+ s = "high speed";
+ else if (dev->gadget.speed == USB_SPEED_UNKNOWN)
+ s = "powered";
+ else
+ s = "full speed";
+ } else
+ s = "not attached";
+ t = scnprintf(next, size,
+ "usbctl0 %02x usbctl1 %02x addr 0x%02x (%s)\n",
+ net2272_read(dev, USBCTL0), t1,
+ net2272_read(dev, OURADDR), s);
+ size -= t;
+ next += t;
+
+ /* Endpoint Registers */
+ for (i = 0; i < 4; ++i) {
+ struct net2272_ep *ep;
+
+ ep = &dev->ep[i];
+ if (i && !ep->desc)
+ continue;
+
+ t1 = net2272_ep_read(ep, EP_CFG);
+ t2 = net2272_ep_read(ep, EP_RSPSET);
+ t = scnprintf(next, size,
+ "\n%s\tcfg %02x rsp (%02x) %s%s%s%s%s%s%s%s"
+ "irqenb %02x\n",
+ ep->ep.name, t1, t2,
+ (t2 & (1 << ALT_NAK_OUT_PACKETS)) ? "NAK " : "",
+ (t2 & (1 << HIDE_STATUS_PHASE)) ? "hide " : "",
+ (t2 & (1 << AUTOVALIDATE)) ? "auto " : "",
+ (t2 & (1 << INTERRUPT_MODE)) ? "interrupt " : "",
+ (t2 & (1 << CONTROL_STATUS_PHASE_HANDSHAKE)) ? "status " : "",
+ (t2 & (1 << NAK_OUT_PACKETS_MODE)) ? "NAKmode " : "",
+ (t2 & (1 << ENDPOINT_TOGGLE)) ? "DATA1 " : "DATA0 ",
+ (t2 & (1 << ENDPOINT_HALT)) ? "HALT " : "",
+ net2272_ep_read(ep, EP_IRQENB));
+ size -= t;
+ next += t;
+
+ t = scnprintf(next, size,
+ "\tstat0 %02x stat1 %02x avail %04x "
+ "(ep%d%s-%s)%s\n",
+ net2272_ep_read(ep, EP_STAT0),
+ net2272_ep_read(ep, EP_STAT1),
+ (net2272_ep_read(ep, EP_AVAIL1) << 8) | net2272_ep_read(ep, EP_AVAIL0),
+ t1 & 0x0f,
+ ep->is_in ? "in" : "out",
+ type_string(t1 >> 5),
+ ep->stopped ? "*" : "");
+ size -= t;
+ next += t;
+
+ t = scnprintf(next, size,
+ "\tep_transfer %06x\n",
+ ((net2272_ep_read(ep, EP_TRANSFER2) & 0xff) << 16) |
+ ((net2272_ep_read(ep, EP_TRANSFER1) & 0xff) << 8) |
+ ((net2272_ep_read(ep, EP_TRANSFER0) & 0xff)));
+ size -= t;
+ next += t;
+
+ t1 = net2272_ep_read(ep, EP_BUFF_STATES) & 0x03;
+ t2 = (net2272_ep_read(ep, EP_BUFF_STATES) >> 2) & 0x03;
+ t = scnprintf(next, size,
+ "\tbuf-a %s buf-b %s\n",
+ buf_state_string(t1),
+ buf_state_string(t2));
+ size -= t;
+ next += t;
+ }
+
+ spin_unlock_irqrestore(&dev->lock, flags);
+
+ return PAGE_SIZE - size;
+}
+static DEVICE_ATTR_RO(registers);
+
+/*---------------------------------------------------------------------------*/
+
+static void
+net2272_set_fifo_mode(struct net2272 *dev, int mode)
+{
+ u8 tmp;
+
+ tmp = net2272_read(dev, LOCCTL) & 0x3f;
+ tmp |= (mode << 6);
+ net2272_write(dev, LOCCTL, tmp);
+
+ INIT_LIST_HEAD(&dev->gadget.ep_list);
+
+ /* always ep-a, ep-c ... maybe not ep-b */
+ list_add_tail(&dev->ep[1].ep.ep_list, &dev->gadget.ep_list);
+
+ switch (mode) {
+ case 0:
+ list_add_tail(&dev->ep[2].ep.ep_list, &dev->gadget.ep_list);
+ dev->ep[1].fifo_size = dev->ep[2].fifo_size = 512;
+ break;
+ case 1:
+ list_add_tail(&dev->ep[2].ep.ep_list, &dev->gadget.ep_list);
+ dev->ep[1].fifo_size = 1024;
+ dev->ep[2].fifo_size = 512;
+ break;
+ case 2:
+ list_add_tail(&dev->ep[2].ep.ep_list, &dev->gadget.ep_list);
+ dev->ep[1].fifo_size = dev->ep[2].fifo_size = 1024;
+ break;
+ case 3:
+ dev->ep[1].fifo_size = 1024;
+ break;
+ }
+
+ /* ep-c is always 2 512 byte buffers */
+ list_add_tail(&dev->ep[3].ep.ep_list, &dev->gadget.ep_list);
+ dev->ep[3].fifo_size = 512;
+}
+
+/*---------------------------------------------------------------------------*/
+
+static void
+net2272_usb_reset(struct net2272 *dev)
+{
+ dev->gadget.speed = USB_SPEED_UNKNOWN;
+
+ net2272_cancel_dma(dev);
+
+ net2272_write(dev, IRQENB0, 0);
+ net2272_write(dev, IRQENB1, 0);
+
+ /* clear irq state */
+ net2272_write(dev, IRQSTAT0, 0xff);
+ net2272_write(dev, IRQSTAT1, ~(1 << SUSPEND_REQUEST_INTERRUPT));
+
+ net2272_write(dev, DMAREQ,
+ (0 << DMA_BUFFER_VALID) |
+ (0 << DMA_REQUEST_ENABLE) |
+ (1 << DMA_CONTROL_DACK) |
+ (dev->dma_eot_polarity << EOT_POLARITY) |
+ (dev->dma_dack_polarity << DACK_POLARITY) |
+ (dev->dma_dreq_polarity << DREQ_POLARITY) |
+ ((dma_ep >> 1) << DMA_ENDPOINT_SELECT));
+
+ net2272_cancel_dma(dev);
+ net2272_set_fifo_mode(dev, (fifo_mode <= 3) ? fifo_mode : 0);
+
+ /* Set the NET2272 ep fifo data width to 16-bit mode and for correct byte swapping
+ * note that the higher level gadget drivers are expected to convert data to little endian.
+ * Enable byte swap for your local bus/cpu if needed by setting BYTE_SWAP in LOCCTL here
+ */
+ net2272_write(dev, LOCCTL, net2272_read(dev, LOCCTL) | (1 << DATA_WIDTH));
+ net2272_write(dev, LOCCTL1, (dma_mode << DMA_MODE));
+}
+
+static void
+net2272_usb_reinit(struct net2272 *dev)
+{
+ int i;
+
+ /* basic endpoint init */
+ for (i = 0; i < 4; ++i) {
+ struct net2272_ep *ep = &dev->ep[i];
+
+ ep->ep.name = ep_name[i];
+ ep->dev = dev;
+ ep->num = i;
+ ep->not_empty = 0;
+
+ if (use_dma && ep->num == dma_ep)
+ ep->dma = 1;
+
+ if (i > 0 && i <= 3)
+ ep->fifo_size = 512;
+ else
+ ep->fifo_size = 64;
+ net2272_ep_reset(ep);
+ }
+ usb_ep_set_maxpacket_limit(&dev->ep[0].ep, 64);
+
+ dev->gadget.ep0 = &dev->ep[0].ep;
+ dev->ep[0].stopped = 0;
+ INIT_LIST_HEAD(&dev->gadget.ep0->ep_list);
+}
+
+static void
+net2272_ep0_start(struct net2272 *dev)
+{
+ struct net2272_ep *ep0 = &dev->ep[0];
+
+ net2272_ep_write(ep0, EP_RSPSET,
+ (1 << NAK_OUT_PACKETS_MODE) |
+ (1 << ALT_NAK_OUT_PACKETS));
+ net2272_ep_write(ep0, EP_RSPCLR,
+ (1 << HIDE_STATUS_PHASE) |
+ (1 << CONTROL_STATUS_PHASE_HANDSHAKE));
+ net2272_write(dev, USBCTL0,
+ (dev->softconnect << USB_DETECT_ENABLE) |
+ (1 << USB_ROOT_PORT_WAKEUP_ENABLE) |
+ (1 << IO_WAKEUP_ENABLE));
+ net2272_write(dev, IRQENB0,
+ (1 << SETUP_PACKET_INTERRUPT_ENABLE) |
+ (1 << ENDPOINT_0_INTERRUPT_ENABLE) |
+ (1 << DMA_DONE_INTERRUPT_ENABLE));
+ net2272_write(dev, IRQENB1,
+ (1 << VBUS_INTERRUPT_ENABLE) |
+ (1 << ROOT_PORT_RESET_INTERRUPT_ENABLE) |
+ (1 << SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE));
+}
+
+/* when a driver is successfully registered, it will receive
+ * control requests including set_configuration(), which enables
+ * non-control requests. then usb traffic follows until a
+ * disconnect is reported. then a host may connect again, or
+ * the driver might get unbound.
+ */
+static int net2272_start(struct usb_gadget *_gadget,
+ struct usb_gadget_driver *driver)
+{
+ struct net2272 *dev;
+ unsigned i;
+
+ if (!driver || !driver->setup ||
+ driver->max_speed != USB_SPEED_HIGH)
+ return -EINVAL;
+
+ dev = container_of(_gadget, struct net2272, gadget);
+
+ for (i = 0; i < 4; ++i)
+ dev->ep[i].irqs = 0;
+ /* hook up the driver ... */
+ dev->softconnect = 1;
+ driver->driver.bus = NULL;
+ dev->driver = driver;
+
+ /* ... then enable host detection and ep0; and we're ready
+ * for set_configuration as well as eventual disconnect.
+ */
+ net2272_ep0_start(dev);
+
+ return 0;
+}
+
+static void
+stop_activity(struct net2272 *dev, struct usb_gadget_driver *driver)
+{
+ int i;
+
+ /* don't disconnect if it's not connected */
+ if (dev->gadget.speed == USB_SPEED_UNKNOWN)
+ driver = NULL;
+
+ /* stop hardware; prevent new request submissions;
+ * and kill any outstanding requests.
+ */
+ net2272_usb_reset(dev);
+ for (i = 0; i < 4; ++i)
+ net2272_dequeue_all(&dev->ep[i]);
+
+ /* report disconnect; the driver is already quiesced */
+ if (driver) {
+ spin_unlock(&dev->lock);
+ driver->disconnect(&dev->gadget);
+ spin_lock(&dev->lock);
+ }
+
+ net2272_usb_reinit(dev);
+}
+
+static int net2272_stop(struct usb_gadget *_gadget)
+{
+ struct net2272 *dev;
+ unsigned long flags;
+
+ dev = container_of(_gadget, struct net2272, gadget);
+
+ spin_lock_irqsave(&dev->lock, flags);
+ stop_activity(dev, NULL);
+ spin_unlock_irqrestore(&dev->lock, flags);
+
+ dev->driver = NULL;
+
+ return 0;
+}
+
+/*---------------------------------------------------------------------------*/
+/* handle ep-a/ep-b dma completions */
+static void
+net2272_handle_dma(struct net2272_ep *ep)
+{
+ struct net2272_request *req;
+ unsigned len;
+ int status;
+
+ if (!list_empty(&ep->queue))
+ req = list_entry(ep->queue.next,
+ struct net2272_request, queue);
+ else
+ req = NULL;
+
+ dev_vdbg(ep->dev->dev, "handle_dma %s req %p\n", ep->ep.name, req);
+
+ /* Ensure DREQ is de-asserted */
+ net2272_write(ep->dev, DMAREQ,
+ (0 << DMA_BUFFER_VALID)
+ | (0 << DMA_REQUEST_ENABLE)
+ | (1 << DMA_CONTROL_DACK)
+ | (ep->dev->dma_eot_polarity << EOT_POLARITY)
+ | (ep->dev->dma_dack_polarity << DACK_POLARITY)
+ | (ep->dev->dma_dreq_polarity << DREQ_POLARITY)
+ | (ep->dma << DMA_ENDPOINT_SELECT));
+
+ ep->dev->dma_busy = 0;
+
+ net2272_ep_write(ep, EP_IRQENB,
+ (1 << DATA_PACKET_RECEIVED_INTERRUPT_ENABLE)
+ | (1 << DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE)
+ | net2272_ep_read(ep, EP_IRQENB));
+
+ /* device-to-host transfer completed */
+ if (ep->is_in) {
+ /* validate a short packet or zlp if necessary */
+ if ((req->req.length % ep->ep.maxpacket != 0) ||
+ req->req.zero)
+ set_fifo_bytecount(ep, 0);
+
+ net2272_done(ep, req, 0);
+ if (!list_empty(&ep->queue)) {
+ req = list_entry(ep->queue.next,
+ struct net2272_request, queue);
+ status = net2272_kick_dma(ep, req);
+ if (status < 0)
+ net2272_pio_advance(ep);
+ }
+
+ /* host-to-device transfer completed */
+ } else {
+ /* terminated with a short packet? */
+ if (net2272_read(ep->dev, IRQSTAT0) &
+ (1 << DMA_DONE_INTERRUPT)) {
+ /* abort system dma */
+ net2272_cancel_dma(ep->dev);
+ }
+
+ /* EP_TRANSFER will contain the number of bytes
+ * actually received.
+ * NOTE: There is no overflow detection on EP_TRANSFER:
+ * We can't deal with transfers larger than 2^24 bytes!
+ */
+ len = (net2272_ep_read(ep, EP_TRANSFER2) << 16)
+ | (net2272_ep_read(ep, EP_TRANSFER1) << 8)
+ | (net2272_ep_read(ep, EP_TRANSFER0));
+
+ if (ep->not_empty)
+ len += 4;
+
+ req->req.actual += len;
+
+ /* get any remaining data */
+ net2272_pio_advance(ep);
+ }
+}
+
+/*---------------------------------------------------------------------------*/
+
+static void
+net2272_handle_ep(struct net2272_ep *ep)
+{
+ struct net2272_request *req;
+ u8 stat0, stat1;
+
+ if (!list_empty(&ep->queue))
+ req = list_entry(ep->queue.next,
+ struct net2272_request, queue);
+ else
+ req = NULL;
+
+ /* ack all, and handle what we care about */
+ stat0 = net2272_ep_read(ep, EP_STAT0);
+ stat1 = net2272_ep_read(ep, EP_STAT1);
+ ep->irqs++;
+
+ dev_vdbg(ep->dev->dev, "%s ack ep_stat0 %02x, ep_stat1 %02x, req %p\n",
+ ep->ep.name, stat0, stat1, req ? &req->req : NULL);
+
+ net2272_ep_write(ep, EP_STAT0, stat0 &
+ ~((1 << NAK_OUT_PACKETS)
+ | (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT)));
+ net2272_ep_write(ep, EP_STAT1, stat1);
+
+ /* data packet(s) received (in the fifo, OUT)
+ * direction must be validated, otherwise control read status phase
+ * could be interpreted as a valid packet
+ */
+ if (!ep->is_in && (stat0 & (1 << DATA_PACKET_RECEIVED_INTERRUPT)))
+ net2272_pio_advance(ep);
+ /* data packet(s) transmitted (IN) */
+ else if (stat0 & (1 << DATA_PACKET_TRANSMITTED_INTERRUPT))
+ net2272_pio_advance(ep);
+}
+
+static struct net2272_ep *
+net2272_get_ep_by_addr(struct net2272 *dev, u16 wIndex)
+{
+ struct net2272_ep *ep;
+
+ if ((wIndex & USB_ENDPOINT_NUMBER_MASK) == 0)
+ return &dev->ep[0];
+
+ list_for_each_entry(ep, &dev->gadget.ep_list, ep.ep_list) {
+ u8 bEndpointAddress;
+
+ if (!ep->desc)
+ continue;
+ bEndpointAddress = ep->desc->bEndpointAddress;
+ if ((wIndex ^ bEndpointAddress) & USB_DIR_IN)
+ continue;
+ if ((wIndex & 0x0f) == (bEndpointAddress & 0x0f))
+ return ep;
+ }
+ return NULL;
+}
+
+/*
+ * USB Test Packet:
+ * JKJKJKJK * 9
+ * JJKKJJKK * 8
+ * JJJJKKKK * 8
+ * JJJJJJJKKKKKKK * 8
+ * JJJJJJJK * 8
+ * {JKKKKKKK * 10}, JK
+ */
+static const u8 net2272_test_packet[] = {
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA,
+ 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE,
+ 0xFE, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0x7F, 0xBF, 0xDF, 0xEF, 0xF7, 0xFB, 0xFD,
+ 0xFC, 0x7E, 0xBF, 0xDF, 0xEF, 0xF7, 0xFD, 0x7E
+};
+
+static void
+net2272_set_test_mode(struct net2272 *dev, int mode)
+{
+ int i;
+
+ /* Disable all net2272 interrupts:
+ * Nothing but a power cycle should stop the test.
+ */
+ net2272_write(dev, IRQENB0, 0x00);
+ net2272_write(dev, IRQENB1, 0x00);
+
+ /* Force tranceiver to high-speed */
+ net2272_write(dev, XCVRDIAG, 1 << FORCE_HIGH_SPEED);
+
+ net2272_write(dev, PAGESEL, 0);
+ net2272_write(dev, EP_STAT0, 1 << DATA_PACKET_TRANSMITTED_INTERRUPT);
+ net2272_write(dev, EP_RSPCLR,
+ (1 << CONTROL_STATUS_PHASE_HANDSHAKE)
+ | (1 << HIDE_STATUS_PHASE));
+ net2272_write(dev, EP_CFG, 1 << ENDPOINT_DIRECTION);
+ net2272_write(dev, EP_STAT1, 1 << BUFFER_FLUSH);
+
+ /* wait for status phase to complete */
+ while (!(net2272_read(dev, EP_STAT0) &
+ (1 << DATA_PACKET_TRANSMITTED_INTERRUPT)))
+ ;
+
+ /* Enable test mode */
+ net2272_write(dev, USBTEST, mode);
+
+ /* load test packet */
+ if (mode == TEST_PACKET) {
+ /* switch to 8 bit mode */
+ net2272_write(dev, LOCCTL, net2272_read(dev, LOCCTL) &
+ ~(1 << DATA_WIDTH));
+
+ for (i = 0; i < sizeof(net2272_test_packet); ++i)
+ net2272_write(dev, EP_DATA, net2272_test_packet[i]);
+
+ /* Validate test packet */
+ net2272_write(dev, EP_TRANSFER0, 0);
+ }
+}
+
+static void
+net2272_handle_stat0_irqs(struct net2272 *dev, u8 stat)
+{
+ struct net2272_ep *ep;
+ u8 num, scratch;
+
+ /* starting a control request? */
+ if (unlikely(stat & (1 << SETUP_PACKET_INTERRUPT))) {
+ union {
+ u8 raw[8];
+ struct usb_ctrlrequest r;
+ } u;
+ int tmp = 0;
+ struct net2272_request *req;
+
+ if (dev->gadget.speed == USB_SPEED_UNKNOWN) {
+ if (net2272_read(dev, USBCTL1) & (1 << USB_HIGH_SPEED))
+ dev->gadget.speed = USB_SPEED_HIGH;
+ else
+ dev->gadget.speed = USB_SPEED_FULL;
+ dev_dbg(dev->dev, "%s\n",
+ usb_speed_string(dev->gadget.speed));
+ }
+
+ ep = &dev->ep[0];
+ ep->irqs++;
+
+ /* make sure any leftover interrupt state is cleared */
+ stat &= ~(1 << ENDPOINT_0_INTERRUPT);
+ while (!list_empty(&ep->queue)) {
+ req = list_entry(ep->queue.next,
+ struct net2272_request, queue);
+ net2272_done(ep, req,
+ (req->req.actual == req->req.length) ? 0 : -EPROTO);
+ }
+ ep->stopped = 0;
+ dev->protocol_stall = 0;
+ net2272_ep_write(ep, EP_STAT0,
+ (1 << DATA_IN_TOKEN_INTERRUPT)
+ | (1 << DATA_OUT_TOKEN_INTERRUPT)
+ | (1 << DATA_PACKET_TRANSMITTED_INTERRUPT)
+ | (1 << DATA_PACKET_RECEIVED_INTERRUPT)
+ | (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT));
+ net2272_ep_write(ep, EP_STAT1,
+ (1 << TIMEOUT)
+ | (1 << USB_OUT_ACK_SENT)
+ | (1 << USB_OUT_NAK_SENT)
+ | (1 << USB_IN_ACK_RCVD)
+ | (1 << USB_IN_NAK_SENT)
+ | (1 << USB_STALL_SENT)
+ | (1 << LOCAL_OUT_ZLP));
+
+ /*
+ * Ensure Control Read pre-validation setting is beyond maximum size
+ * - Control Writes can leave non-zero values in EP_TRANSFER. If
+ * an EP0 transfer following the Control Write is a Control Read,
+ * the NET2272 sees the non-zero EP_TRANSFER as an unexpected
+ * pre-validation count.
+ * - Setting EP_TRANSFER beyond the maximum EP0 transfer size ensures
+ * the pre-validation count cannot cause an unexpected validatation
+ */
+ net2272_write(dev, PAGESEL, 0);
+ net2272_write(dev, EP_TRANSFER2, 0xff);
+ net2272_write(dev, EP_TRANSFER1, 0xff);
+ net2272_write(dev, EP_TRANSFER0, 0xff);
+
+ u.raw[0] = net2272_read(dev, SETUP0);
+ u.raw[1] = net2272_read(dev, SETUP1);
+ u.raw[2] = net2272_read(dev, SETUP2);
+ u.raw[3] = net2272_read(dev, SETUP3);
+ u.raw[4] = net2272_read(dev, SETUP4);
+ u.raw[5] = net2272_read(dev, SETUP5);
+ u.raw[6] = net2272_read(dev, SETUP6);
+ u.raw[7] = net2272_read(dev, SETUP7);
+ /*
+ * If you have a big endian cpu make sure le16_to_cpus
+ * performs the proper byte swapping here...
+ */
+ le16_to_cpus(&u.r.wValue);
+ le16_to_cpus(&u.r.wIndex);
+ le16_to_cpus(&u.r.wLength);
+
+ /* ack the irq */
+ net2272_write(dev, IRQSTAT0, 1 << SETUP_PACKET_INTERRUPT);
+ stat ^= (1 << SETUP_PACKET_INTERRUPT);
+
+ /* watch control traffic at the token level, and force
+ * synchronization before letting the status phase happen.
+ */
+ ep->is_in = (u.r.bRequestType & USB_DIR_IN) != 0;
+ if (ep->is_in) {
+ scratch = (1 << DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE)
+ | (1 << DATA_OUT_TOKEN_INTERRUPT_ENABLE)
+ | (1 << DATA_IN_TOKEN_INTERRUPT_ENABLE);
+ stop_out_naking(ep);
+ } else
+ scratch = (1 << DATA_PACKET_RECEIVED_INTERRUPT_ENABLE)
+ | (1 << DATA_OUT_TOKEN_INTERRUPT_ENABLE)
+ | (1 << DATA_IN_TOKEN_INTERRUPT_ENABLE);
+ net2272_ep_write(ep, EP_IRQENB, scratch);
+
+ if ((u.r.bRequestType & USB_TYPE_MASK) != USB_TYPE_STANDARD)
+ goto delegate;
+ switch (u.r.bRequest) {
+ case USB_REQ_GET_STATUS: {
+ struct net2272_ep *e;
+ u16 status = 0;
+
+ switch (u.r.bRequestType & USB_RECIP_MASK) {
+ case USB_RECIP_ENDPOINT:
+ e = net2272_get_ep_by_addr(dev, u.r.wIndex);
+ if (!e || u.r.wLength > 2)
+ goto do_stall;
+ if (net2272_ep_read(e, EP_RSPSET) & (1 << ENDPOINT_HALT))
+ status = __constant_cpu_to_le16(1);
+ else
+ status = __constant_cpu_to_le16(0);
+
+ /* don't bother with a request object! */
+ net2272_ep_write(&dev->ep[0], EP_IRQENB, 0);
+ writew(status, net2272_reg_addr(dev, EP_DATA));
+ set_fifo_bytecount(&dev->ep[0], 0);
+ allow_status(ep);
+ dev_vdbg(dev->dev, "%s stat %02x\n",
+ ep->ep.name, status);
+ goto next_endpoints;
+ case USB_RECIP_DEVICE:
+ if (u.r.wLength > 2)
+ goto do_stall;
+ if (dev->gadget.is_selfpowered)
+ status = (1 << USB_DEVICE_SELF_POWERED);
+
+ /* don't bother with a request object! */
+ net2272_ep_write(&dev->ep[0], EP_IRQENB, 0);
+ writew(status, net2272_reg_addr(dev, EP_DATA));
+ set_fifo_bytecount(&dev->ep[0], 0);
+ allow_status(ep);
+ dev_vdbg(dev->dev, "device stat %02x\n", status);
+ goto next_endpoints;
+ case USB_RECIP_INTERFACE:
+ if (u.r.wLength > 2)
+ goto do_stall;
+
+ /* don't bother with a request object! */
+ net2272_ep_write(&dev->ep[0], EP_IRQENB, 0);
+ writew(status, net2272_reg_addr(dev, EP_DATA));
+ set_fifo_bytecount(&dev->ep[0], 0);
+ allow_status(ep);
+ dev_vdbg(dev->dev, "interface status %02x\n", status);
+ goto next_endpoints;
+ }
+
+ break;
+ }
+ case USB_REQ_CLEAR_FEATURE: {
+ struct net2272_ep *e;
+
+ if (u.r.bRequestType != USB_RECIP_ENDPOINT)
+ goto delegate;
+ if (u.r.wValue != USB_ENDPOINT_HALT ||
+ u.r.wLength != 0)
+ goto do_stall;
+ e = net2272_get_ep_by_addr(dev, u.r.wIndex);
+ if (!e)
+ goto do_stall;
+ if (e->wedged) {
+ dev_vdbg(dev->dev, "%s wedged, halt not cleared\n",
+ ep->ep.name);
+ } else {
+ dev_vdbg(dev->dev, "%s clear halt\n", ep->ep.name);
+ clear_halt(e);
+ }
+ allow_status(ep);
+ goto next_endpoints;
+ }
+ case USB_REQ_SET_FEATURE: {
+ struct net2272_ep *e;
+
+ if (u.r.bRequestType == USB_RECIP_DEVICE) {
+ if (u.r.wIndex != NORMAL_OPERATION)
+ net2272_set_test_mode(dev, (u.r.wIndex >> 8));
+ allow_status(ep);
+ dev_vdbg(dev->dev, "test mode: %d\n", u.r.wIndex);
+ goto next_endpoints;
+ } else if (u.r.bRequestType != USB_RECIP_ENDPOINT)
+ goto delegate;
+ if (u.r.wValue != USB_ENDPOINT_HALT ||
+ u.r.wLength != 0)
+ goto do_stall;
+ e = net2272_get_ep_by_addr(dev, u.r.wIndex);
+ if (!e)
+ goto do_stall;
+ set_halt(e);
+ allow_status(ep);
+ dev_vdbg(dev->dev, "%s set halt\n", ep->ep.name);
+ goto next_endpoints;
+ }
+ case USB_REQ_SET_ADDRESS: {
+ net2272_write(dev, OURADDR, u.r.wValue & 0xff);
+ allow_status(ep);
+ break;
+ }
+ default:
+ delegate:
+ dev_vdbg(dev->dev, "setup %02x.%02x v%04x i%04x "
+ "ep_cfg %08x\n",
+ u.r.bRequestType, u.r.bRequest,
+ u.r.wValue, u.r.wIndex,
+ net2272_ep_read(ep, EP_CFG));
+ spin_unlock(&dev->lock);
+ tmp = dev->driver->setup(&dev->gadget, &u.r);
+ spin_lock(&dev->lock);
+ }
+
+ /* stall ep0 on error */
+ if (tmp < 0) {
+ do_stall:
+ dev_vdbg(dev->dev, "req %02x.%02x protocol STALL; stat %d\n",
+ u.r.bRequestType, u.r.bRequest, tmp);
+ dev->protocol_stall = 1;
+ }
+ /* endpoint dma irq? */
+ } else if (stat & (1 << DMA_DONE_INTERRUPT)) {
+ net2272_cancel_dma(dev);
+ net2272_write(dev, IRQSTAT0, 1 << DMA_DONE_INTERRUPT);
+ stat &= ~(1 << DMA_DONE_INTERRUPT);
+ num = (net2272_read(dev, DMAREQ) & (1 << DMA_ENDPOINT_SELECT))
+ ? 2 : 1;
+
+ ep = &dev->ep[num];
+ net2272_handle_dma(ep);
+ }
+
+ next_endpoints:
+ /* endpoint data irq? */
+ scratch = stat & 0x0f;
+ stat &= ~0x0f;
+ for (num = 0; scratch; num++) {
+ u8 t;
+
+ /* does this endpoint's FIFO and queue need tending? */
+ t = 1 << num;
+ if ((scratch & t) == 0)
+ continue;
+ scratch ^= t;
+
+ ep = &dev->ep[num];
+ net2272_handle_ep(ep);
+ }
+
+ /* some interrupts we can just ignore */
+ stat &= ~(1 << SOF_INTERRUPT);
+
+ if (stat)
+ dev_dbg(dev->dev, "unhandled irqstat0 %02x\n", stat);
+}
+
+static void
+net2272_handle_stat1_irqs(struct net2272 *dev, u8 stat)
+{
+ u8 tmp, mask;
+
+ /* after disconnect there's nothing else to do! */
+ tmp = (1 << VBUS_INTERRUPT) | (1 << ROOT_PORT_RESET_INTERRUPT);
+ mask = (1 << USB_HIGH_SPEED) | (1 << USB_FULL_SPEED);
+
+ if (stat & tmp) {
+ bool reset = false;
+ bool disconnect = false;
+
+ /*
+ * Ignore disconnects and resets if the speed hasn't been set.
+ * VBUS can bounce and there's always an initial reset.
+ */
+ net2272_write(dev, IRQSTAT1, tmp);
+ if (dev->gadget.speed != USB_SPEED_UNKNOWN) {
+ if ((stat & (1 << VBUS_INTERRUPT)) &&
+ (net2272_read(dev, USBCTL1) &
+ (1 << VBUS_PIN)) == 0) {
+ disconnect = true;
+ dev_dbg(dev->dev, "disconnect %s\n",
+ dev->driver->driver.name);
+ } else if ((stat & (1 << ROOT_PORT_RESET_INTERRUPT)) &&
+ (net2272_read(dev, USBCTL1) & mask)
+ == 0) {
+ reset = true;
+ dev_dbg(dev->dev, "reset %s\n",
+ dev->driver->driver.name);
+ }
+
+ if (disconnect || reset) {
+ stop_activity(dev, dev->driver);
+ net2272_ep0_start(dev);
+ spin_unlock(&dev->lock);
+ if (reset)
+ usb_gadget_udc_reset
+ (&dev->gadget, dev->driver);
+ else
+ (dev->driver->disconnect)
+ (&dev->gadget);
+ spin_lock(&dev->lock);
+ return;
+ }
+ }
+ stat &= ~tmp;
+
+ if (!stat)
+ return;
+ }
+
+ tmp = (1 << SUSPEND_REQUEST_CHANGE_INTERRUPT);
+ if (stat & tmp) {
+ net2272_write(dev, IRQSTAT1, tmp);
+ if (stat & (1 << SUSPEND_REQUEST_INTERRUPT)) {
+ if (dev->driver->suspend)
+ dev->driver->suspend(&dev->gadget);
+ if (!enable_suspend) {
+ stat &= ~(1 << SUSPEND_REQUEST_INTERRUPT);
+ dev_dbg(dev->dev, "Suspend disabled, ignoring\n");
+ }
+ } else {
+ if (dev->driver->resume)
+ dev->driver->resume(&dev->gadget);
+ }
+ stat &= ~tmp;
+ }
+
+ /* clear any other status/irqs */
+ if (stat)
+ net2272_write(dev, IRQSTAT1, stat);
+
+ /* some status we can just ignore */
+ stat &= ~((1 << CONTROL_STATUS_INTERRUPT)
+ | (1 << SUSPEND_REQUEST_INTERRUPT)
+ | (1 << RESUME_INTERRUPT));
+ if (!stat)
+ return;
+ else
+ dev_dbg(dev->dev, "unhandled irqstat1 %02x\n", stat);
+}
+
+static irqreturn_t net2272_irq(int irq, void *_dev)
+{
+ struct net2272 *dev = _dev;
+#if defined(PLX_PCI_RDK) || defined(PLX_PCI_RDK2)
+ u32 intcsr;
+#endif
+#if defined(PLX_PCI_RDK)
+ u8 dmareq;
+#endif
+ spin_lock(&dev->lock);
+#if defined(PLX_PCI_RDK)
+ intcsr = readl(dev->rdk1.plx9054_base_addr + INTCSR);
+
+ if ((intcsr & LOCAL_INTERRUPT_TEST) == LOCAL_INTERRUPT_TEST) {
+ writel(intcsr & ~(1 << PCI_INTERRUPT_ENABLE),
+ dev->rdk1.plx9054_base_addr + INTCSR);
+ net2272_handle_stat1_irqs(dev, net2272_read(dev, IRQSTAT1));
+ net2272_handle_stat0_irqs(dev, net2272_read(dev, IRQSTAT0));
+ intcsr = readl(dev->rdk1.plx9054_base_addr + INTCSR);
+ writel(intcsr | (1 << PCI_INTERRUPT_ENABLE),
+ dev->rdk1.plx9054_base_addr + INTCSR);
+ }
+ if ((intcsr & DMA_CHANNEL_0_TEST) == DMA_CHANNEL_0_TEST) {
+ writeb((1 << CHANNEL_CLEAR_INTERRUPT | (0 << CHANNEL_ENABLE)),
+ dev->rdk1.plx9054_base_addr + DMACSR0);
+
+ dmareq = net2272_read(dev, DMAREQ);
+ if (dmareq & 0x01)
+ net2272_handle_dma(&dev->ep[2]);
+ else
+ net2272_handle_dma(&dev->ep[1]);
+ }
+#endif
+#if defined(PLX_PCI_RDK2)
+ /* see if PCI int for us by checking irqstat */
+ intcsr = readl(dev->rdk2.fpga_base_addr + RDK2_IRQSTAT);
+ if (!intcsr & (1 << NET2272_PCI_IRQ)) {
+ spin_unlock(&dev->lock);
+ return IRQ_NONE;
+ }
+ /* check dma interrupts */
+#endif
+ /* Platform/devcice interrupt handler */
+#if !defined(PLX_PCI_RDK)
+ net2272_handle_stat1_irqs(dev, net2272_read(dev, IRQSTAT1));
+ net2272_handle_stat0_irqs(dev, net2272_read(dev, IRQSTAT0));
+#endif
+ spin_unlock(&dev->lock);
+
+ return IRQ_HANDLED;
+}
+
+static int net2272_present(struct net2272 *dev)
+{
+ /*
+ * Quick test to see if CPU can communicate properly with the NET2272.
+ * Verifies connection using writes and reads to write/read and
+ * read-only registers.
+ *
+ * This routine is strongly recommended especially during early bring-up
+ * of new hardware, however for designs that do not apply Power On System
+ * Tests (POST) it may discarded (or perhaps minimized).
+ */
+ unsigned int ii;
+ u8 val, refval;
+
+ /* Verify NET2272 write/read SCRATCH register can write and read */
+ refval = net2272_read(dev, SCRATCH);
+ for (ii = 0; ii < 0x100; ii += 7) {
+ net2272_write(dev, SCRATCH, ii);
+ val = net2272_read(dev, SCRATCH);
+ if (val != ii) {
+ dev_dbg(dev->dev,
+ "%s: write/read SCRATCH register test failed: "
+ "wrote:0x%2.2x, read:0x%2.2x\n",
+ __func__, ii, val);
+ return -EINVAL;
+ }
+ }
+ /* To be nice, we write the original SCRATCH value back: */
+ net2272_write(dev, SCRATCH, refval);
+
+ /* Verify NET2272 CHIPREV register is read-only: */
+ refval = net2272_read(dev, CHIPREV_2272);
+ for (ii = 0; ii < 0x100; ii += 7) {
+ net2272_write(dev, CHIPREV_2272, ii);
+ val = net2272_read(dev, CHIPREV_2272);
+ if (val != refval) {
+ dev_dbg(dev->dev,
+ "%s: write/read CHIPREV register test failed: "
+ "wrote 0x%2.2x, read:0x%2.2x expected:0x%2.2x\n",
+ __func__, ii, val, refval);
+ return -EINVAL;
+ }
+ }
+
+ /*
+ * Verify NET2272's "NET2270 legacy revision" register
+ * - NET2272 has two revision registers. The NET2270 legacy revision
+ * register should read the same value, regardless of the NET2272
+ * silicon revision. The legacy register applies to NET2270
+ * firmware being applied to the NET2272.
+ */
+ val = net2272_read(dev, CHIPREV_LEGACY);
+ if (val != NET2270_LEGACY_REV) {
+ /*
+ * Unexpected legacy revision value
+ * - Perhaps the chip is a NET2270?
+ */
+ dev_dbg(dev->dev,
+ "%s: WARNING: UNEXPECTED NET2272 LEGACY REGISTER VALUE:\n"
+ " - CHIPREV_LEGACY: expected 0x%2.2x, got:0x%2.2x. (Not NET2272?)\n",
+ __func__, NET2270_LEGACY_REV, val);
+ return -EINVAL;
+ }
+
+ /*
+ * Verify NET2272 silicon revision
+ * - This revision register is appropriate for the silicon version
+ * of the NET2272
+ */
+ val = net2272_read(dev, CHIPREV_2272);
+ switch (val) {
+ case CHIPREV_NET2272_R1:
+ /*
+ * NET2272 Rev 1 has DMA related errata:
+ * - Newer silicon (Rev 1A or better) required
+ */
+ dev_dbg(dev->dev,
+ "%s: Rev 1 detected: newer silicon recommended for DMA support\n",
+ __func__);
+ break;
+ case CHIPREV_NET2272_R1A:
+ break;
+ default:
+ /* NET2272 silicon version *may* not work with this firmware */
+ dev_dbg(dev->dev,
+ "%s: unexpected silicon revision register value: "
+ " CHIPREV_2272: 0x%2.2x\n",
+ __func__, val);
+ /*
+ * Return Success, even though the chip rev is not an expected value
+ * - Older, pre-built firmware can attempt to operate on newer silicon
+ * - Often, new silicon is perfectly compatible
+ */
+ }
+
+ /* Success: NET2272 checks out OK */
+ return 0;
+}
+
+static void
+net2272_gadget_release(struct device *_dev)
+{
+ struct net2272 *dev = dev_get_drvdata(_dev);
+ kfree(dev);
+}
+
+/*---------------------------------------------------------------------------*/
+
+static void
+net2272_remove(struct net2272 *dev)
+{
+ usb_del_gadget_udc(&dev->gadget);
+ free_irq(dev->irq, dev);
+ iounmap(dev->base_addr);
+ device_remove_file(dev->dev, &dev_attr_registers);
+
+ dev_info(dev->dev, "unbind\n");
+}
+
+static struct net2272 *net2272_probe_init(struct device *dev, unsigned int irq)
+{
+ struct net2272 *ret;
+
+ if (!irq) {
+ dev_dbg(dev, "No IRQ!\n");
+ return ERR_PTR(-ENODEV);
+ }
+
+ /* alloc, and start init */
+ ret = kzalloc(sizeof(*ret), GFP_KERNEL);
+ if (!ret)
+ return ERR_PTR(-ENOMEM);
+
+ spin_lock_init(&ret->lock);
+ ret->irq = irq;
+ ret->dev = dev;
+ ret->gadget.ops = &net2272_ops;
+ ret->gadget.max_speed = USB_SPEED_HIGH;
+
+ /* the "gadget" abstracts/virtualizes the controller */
+ ret->gadget.name = driver_name;
+
+ return ret;
+}
+
+static int
+net2272_probe_fin(struct net2272 *dev, unsigned int irqflags)
+{
+ int ret;
+
+ /* See if there... */
+ if (net2272_present(dev)) {
+ dev_warn(dev->dev, "2272 not found!\n");
+ ret = -ENODEV;
+ goto err;
+ }
+
+ net2272_usb_reset(dev);
+ net2272_usb_reinit(dev);
+
+ ret = request_irq(dev->irq, net2272_irq, irqflags, driver_name, dev);
+ if (ret) {
+ dev_err(dev->dev, "request interrupt %i failed\n", dev->irq);
+ goto err;
+ }
+
+ dev->chiprev = net2272_read(dev, CHIPREV_2272);
+
+ /* done */
+ dev_info(dev->dev, "%s\n", driver_desc);
+ dev_info(dev->dev, "irq %i, mem %p, chip rev %04x, dma %s\n",
+ dev->irq, dev->base_addr, dev->chiprev,
+ dma_mode_string());
+ dev_info(dev->dev, "version: %s\n", driver_vers);
+
+ ret = device_create_file(dev->dev, &dev_attr_registers);
+ if (ret)
+ goto err_irq;
+
+ ret = usb_add_gadget_udc_release(dev->dev, &dev->gadget,
+ net2272_gadget_release);
+ if (ret)
+ goto err_add_udc;
+
+ return 0;
+
+err_add_udc:
+ device_remove_file(dev->dev, &dev_attr_registers);
+ err_irq:
+ free_irq(dev->irq, dev);
+ err:
+ return ret;
+}
+
+#ifdef CONFIG_PCI
+
+/*
+ * wrap this driver around the specified device, but
+ * don't respond over USB until a gadget driver binds to us
+ */
+
+static int
+net2272_rdk1_probe(struct pci_dev *pdev, struct net2272 *dev)
+{
+ unsigned long resource, len, tmp;
+ void __iomem *mem_mapped_addr[4];
+ int ret, i;
+
+ /*
+ * BAR 0 holds PLX 9054 config registers
+ * BAR 1 is i/o memory; unused here
+ * BAR 2 holds EPLD config registers
+ * BAR 3 holds NET2272 registers
+ */
+
+ /* Find and map all address spaces */
+ for (i = 0; i < 4; ++i) {
+ if (i == 1)
+ continue; /* BAR1 unused */
+
+ resource = pci_resource_start(pdev, i);
+ len = pci_resource_len(pdev, i);
+
+ if (!request_mem_region(resource, len, driver_name)) {
+ dev_dbg(dev->dev, "controller already in use\n");
+ ret = -EBUSY;
+ goto err;
+ }
+
+ mem_mapped_addr[i] = ioremap_nocache(resource, len);
+ if (mem_mapped_addr[i] == NULL) {
+ release_mem_region(resource, len);
+ dev_dbg(dev->dev, "can't map memory\n");
+ ret = -EFAULT;
+ goto err;
+ }
+ }
+
+ dev->rdk1.plx9054_base_addr = mem_mapped_addr[0];
+ dev->rdk1.epld_base_addr = mem_mapped_addr[2];
+ dev->base_addr = mem_mapped_addr[3];
+
+ /* Set PLX 9054 bus width (16 bits) */
+ tmp = readl(dev->rdk1.plx9054_base_addr + LBRD1);
+ writel((tmp & ~(3 << MEMORY_SPACE_LOCAL_BUS_WIDTH)) | W16_BIT,
+ dev->rdk1.plx9054_base_addr + LBRD1);
+
+ /* Enable PLX 9054 Interrupts */
+ writel(readl(dev->rdk1.plx9054_base_addr + INTCSR) |
+ (1 << PCI_INTERRUPT_ENABLE) |
+ (1 << LOCAL_INTERRUPT_INPUT_ENABLE),
+ dev->rdk1.plx9054_base_addr + INTCSR);
+
+ writeb((1 << CHANNEL_CLEAR_INTERRUPT | (0 << CHANNEL_ENABLE)),
+ dev->rdk1.plx9054_base_addr + DMACSR0);
+
+ /* reset */
+ writeb((1 << EPLD_DMA_ENABLE) |
+ (1 << DMA_CTL_DACK) |
+ (1 << DMA_TIMEOUT_ENABLE) |
+ (1 << USER) |
+ (0 << MPX_MODE) |
+ (1 << BUSWIDTH) |
+ (1 << NET2272_RESET),
+ dev->base_addr + EPLD_IO_CONTROL_REGISTER);
+
+ mb();
+ writeb(readb(dev->base_addr + EPLD_IO_CONTROL_REGISTER) &
+ ~(1 << NET2272_RESET),
+ dev->base_addr + EPLD_IO_CONTROL_REGISTER);
+ udelay(200);
+
+ return 0;
+
+ err:
+ while (--i >= 0) {
+ iounmap(mem_mapped_addr[i]);
+ release_mem_region(pci_resource_start(pdev, i),
+ pci_resource_len(pdev, i));
+ }
+
+ return ret;
+}
+
+static int
+net2272_rdk2_probe(struct pci_dev *pdev, struct net2272 *dev)
+{
+ unsigned long resource, len;
+ void __iomem *mem_mapped_addr[2];
+ int ret, i;
+
+ /*
+ * BAR 0 holds FGPA config registers
+ * BAR 1 holds NET2272 registers
+ */
+
+ /* Find and map all address spaces, bar2-3 unused in rdk 2 */
+ for (i = 0; i < 2; ++i) {
+ resource = pci_resource_start(pdev, i);
+ len = pci_resource_len(pdev, i);
+
+ if (!request_mem_region(resource, len, driver_name)) {
+ dev_dbg(dev->dev, "controller already in use\n");
+ ret = -EBUSY;
+ goto err;
+ }
+
+ mem_mapped_addr[i] = ioremap_nocache(resource, len);
+ if (mem_mapped_addr[i] == NULL) {
+ release_mem_region(resource, len);
+ dev_dbg(dev->dev, "can't map memory\n");
+ ret = -EFAULT;
+ goto err;
+ }
+ }
+
+ dev->rdk2.fpga_base_addr = mem_mapped_addr[0];
+ dev->base_addr = mem_mapped_addr[1];
+
+ mb();
+ /* Set 2272 bus width (16 bits) and reset */
+ writel((1 << CHIP_RESET), dev->rdk2.fpga_base_addr + RDK2_LOCCTLRDK);
+ udelay(200);
+ writel((1 << BUS_WIDTH), dev->rdk2.fpga_base_addr + RDK2_LOCCTLRDK);
+ /* Print fpga version number */
+ dev_info(dev->dev, "RDK2 FPGA version %08x\n",
+ readl(dev->rdk2.fpga_base_addr + RDK2_FPGAREV));
+ /* Enable FPGA Interrupts */
+ writel((1 << NET2272_PCI_IRQ), dev->rdk2.fpga_base_addr + RDK2_IRQENB);
+
+ return 0;
+
+ err:
+ while (--i >= 0) {
+ iounmap(mem_mapped_addr[i]);
+ release_mem_region(pci_resource_start(pdev, i),
+ pci_resource_len(pdev, i));
+ }
+
+ return ret;
+}
+
+static int
+net2272_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+ struct net2272 *dev;
+ int ret;
+
+ dev = net2272_probe_init(&pdev->dev, pdev->irq);
+ if (IS_ERR(dev))
+ return PTR_ERR(dev);
+ dev->dev_id = pdev->device;
+
+ if (pci_enable_device(pdev) < 0) {
+ ret = -ENODEV;
+ goto err_free;
+ }
+
+ pci_set_master(pdev);
+
+ switch (pdev->device) {
+ case PCI_DEVICE_ID_RDK1: ret = net2272_rdk1_probe(pdev, dev); break;
+ case PCI_DEVICE_ID_RDK2: ret = net2272_rdk2_probe(pdev, dev); break;
+ default: BUG();
+ }
+ if (ret)
+ goto err_pci;
+
+ ret = net2272_probe_fin(dev, 0);
+ if (ret)
+ goto err_pci;
+
+ pci_set_drvdata(pdev, dev);
+
+ return 0;
+
+ err_pci:
+ pci_disable_device(pdev);
+ err_free:
+ kfree(dev);
+
+ return ret;
+}
+
+static void
+net2272_rdk1_remove(struct pci_dev *pdev, struct net2272 *dev)
+{
+ int i;
+
+ /* disable PLX 9054 interrupts */
+ writel(readl(dev->rdk1.plx9054_base_addr + INTCSR) &
+ ~(1 << PCI_INTERRUPT_ENABLE),
+ dev->rdk1.plx9054_base_addr + INTCSR);
+
+ /* clean up resources allocated during probe() */
+ iounmap(dev->rdk1.plx9054_base_addr);
+ iounmap(dev->rdk1.epld_base_addr);
+
+ for (i = 0; i < 4; ++i) {
+ if (i == 1)
+ continue; /* BAR1 unused */
+ release_mem_region(pci_resource_start(pdev, i),
+ pci_resource_len(pdev, i));
+ }
+}
+
+static void
+net2272_rdk2_remove(struct pci_dev *pdev, struct net2272 *dev)
+{
+ int i;
+
+ /* disable fpga interrupts
+ writel(readl(dev->rdk1.plx9054_base_addr + INTCSR) &
+ ~(1 << PCI_INTERRUPT_ENABLE),
+ dev->rdk1.plx9054_base_addr + INTCSR);
+ */
+
+ /* clean up resources allocated during probe() */
+ iounmap(dev->rdk2.fpga_base_addr);
+
+ for (i = 0; i < 2; ++i)
+ release_mem_region(pci_resource_start(pdev, i),
+ pci_resource_len(pdev, i));
+}
+
+static void
+net2272_pci_remove(struct pci_dev *pdev)
+{
+ struct net2272 *dev = pci_get_drvdata(pdev);
+
+ net2272_remove(dev);
+
+ switch (pdev->device) {
+ case PCI_DEVICE_ID_RDK1: net2272_rdk1_remove(pdev, dev); break;
+ case PCI_DEVICE_ID_RDK2: net2272_rdk2_remove(pdev, dev); break;
+ default: BUG();
+ }
+
+ pci_disable_device(pdev);
+
+ kfree(dev);
+}
+
+/* Table of matching PCI IDs */
+static struct pci_device_id pci_ids[] = {
+ { /* RDK 1 card */
+ .class = ((PCI_CLASS_BRIDGE_OTHER << 8) | 0xfe),
+ .class_mask = 0,
+ .vendor = PCI_VENDOR_ID_PLX,
+ .device = PCI_DEVICE_ID_RDK1,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ },
+ { /* RDK 2 card */
+ .class = ((PCI_CLASS_BRIDGE_OTHER << 8) | 0xfe),
+ .class_mask = 0,
+ .vendor = PCI_VENDOR_ID_PLX,
+ .device = PCI_DEVICE_ID_RDK2,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ },
+ { }
+};
+MODULE_DEVICE_TABLE(pci, pci_ids);
+
+static struct pci_driver net2272_pci_driver = {
+ .name = driver_name,
+ .id_table = pci_ids,
+
+ .probe = net2272_pci_probe,
+ .remove = net2272_pci_remove,
+};
+
+static int net2272_pci_register(void)
+{
+ return pci_register_driver(&net2272_pci_driver);
+}
+
+static void net2272_pci_unregister(void)
+{
+ pci_unregister_driver(&net2272_pci_driver);
+}
+
+#else
+static inline int net2272_pci_register(void) { return 0; }
+static inline void net2272_pci_unregister(void) { }
+#endif
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_plat_probe(struct platform_device *pdev)
+{
+ struct net2272 *dev;
+ int ret;
+ unsigned int irqflags;
+ resource_size_t base, len;
+ struct resource *iomem, *iomem_bus, *irq_res;
+
+ irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ iomem_bus = platform_get_resource(pdev, IORESOURCE_BUS, 0);
+ if (!irq_res || !iomem) {
+ dev_err(&pdev->dev, "must provide irq/base addr");
+ return -EINVAL;
+ }
+
+ dev = net2272_probe_init(&pdev->dev, irq_res->start);
+ if (IS_ERR(dev))
+ return PTR_ERR(dev);
+
+ irqflags = 0;
+ if (irq_res->flags & IORESOURCE_IRQ_HIGHEDGE)
+ irqflags |= IRQF_TRIGGER_RISING;
+ if (irq_res->flags & IORESOURCE_IRQ_LOWEDGE)
+ irqflags |= IRQF_TRIGGER_FALLING;
+ if (irq_res->flags & IORESOURCE_IRQ_HIGHLEVEL)
+ irqflags |= IRQF_TRIGGER_HIGH;
+ if (irq_res->flags & IORESOURCE_IRQ_LOWLEVEL)
+ irqflags |= IRQF_TRIGGER_LOW;
+
+ base = iomem->start;
+ len = resource_size(iomem);
+ if (iomem_bus)
+ dev->base_shift = iomem_bus->start;
+
+ if (!request_mem_region(base, len, driver_name)) {
+ dev_dbg(dev->dev, "get request memory region!\n");
+ ret = -EBUSY;
+ goto err;
+ }
+ dev->base_addr = ioremap_nocache(base, len);
+ if (!dev->base_addr) {
+ dev_dbg(dev->dev, "can't map memory\n");
+ ret = -EFAULT;
+ goto err_req;
+ }
+
+ ret = net2272_probe_fin(dev, IRQF_TRIGGER_LOW);
+ if (ret)
+ goto err_io;
+
+ platform_set_drvdata(pdev, dev);
+ dev_info(&pdev->dev, "running in 16-bit, %sbyte swap local bus mode\n",
+ (net2272_read(dev, LOCCTL) & (1 << BYTE_SWAP)) ? "" : "no ");
+
+ return 0;
+
+ err_io:
+ iounmap(dev->base_addr);
+ err_req:
+ release_mem_region(base, len);
+ err:
+ return ret;
+}
+
+static int
+net2272_plat_remove(struct platform_device *pdev)
+{
+ struct net2272 *dev = platform_get_drvdata(pdev);
+
+ net2272_remove(dev);
+
+ release_mem_region(pdev->resource[0].start,
+ resource_size(&pdev->resource[0]));
+
+ kfree(dev);
+
+ return 0;
+}
+
+static struct platform_driver net2272_plat_driver = {
+ .probe = net2272_plat_probe,
+ .remove = net2272_plat_remove,
+ .driver = {
+ .name = driver_name,
+ },
+ /* FIXME .suspend, .resume */
+};
+MODULE_ALIAS("platform:net2272");
+
+static int __init net2272_init(void)
+{
+ int ret;
+
+ ret = net2272_pci_register();
+ if (ret)
+ return ret;
+ ret = platform_driver_register(&net2272_plat_driver);
+ if (ret)
+ goto err_pci;
+ return ret;
+
+err_pci:
+ net2272_pci_unregister();
+ return ret;
+}
+module_init(net2272_init);
+
+static void __exit net2272_cleanup(void)
+{
+ net2272_pci_unregister();
+ platform_driver_unregister(&net2272_plat_driver);
+}
+module_exit(net2272_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_AUTHOR("PLX Technology, Inc.");
+MODULE_LICENSE("GPL");
Code Review / kvmfornfv.git / blobdiff