#define TEMPSENSE2_PANIC_VALUE_SHIFT 16
#define TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
+#define OCOTP_MEM0 0x0480
#define OCOTP_ANA1 0x04e0
/* The driver supports 1 passive trip point and 1 critical trip point */
IMX_TRIP_NUM,
};
-/*
- * It defines the temperature in millicelsius for passive trip point
- * that will trigger cooling action when crossed.
- */
-#define IMX_TEMP_PASSIVE 85000
-
#define IMX_POLLING_DELAY 2000 /* millisecond */
#define IMX_PASSIVE_DELAY 1000
enum thermal_device_mode mode;
struct regmap *tempmon;
u32 c1, c2; /* See formula in imx_get_sensor_data() */
- unsigned long temp_passive;
- unsigned long temp_critical;
- unsigned long alarm_temp;
- unsigned long last_temp;
+ int temp_passive;
+ int temp_critical;
+ int temp_max;
+ int alarm_temp;
+ int last_temp;
bool irq_enabled;
int irq;
struct clk *thermal_clk;
const struct thermal_soc_data *socdata;
+ const char *temp_grade;
};
static void imx_set_panic_temp(struct imx_thermal_data *data,
- signed long panic_temp)
+ int panic_temp)
{
struct regmap *map = data->tempmon;
int critical_value;
}
static void imx_set_alarm_temp(struct imx_thermal_data *data,
- signed long alarm_temp)
+ int alarm_temp)
{
struct regmap *map = data->tempmon;
int alarm_value;
TEMPSENSE0_ALARM_VALUE_SHIFT);
}
-static int imx_get_temp(struct thermal_zone_device *tz, unsigned long *temp)
+static int imx_get_temp(struct thermal_zone_device *tz, int *temp)
{
struct imx_thermal_data *data = tz->devdata;
struct regmap *map = data->tempmon;
if (data->alarm_temp == data->temp_critical &&
*temp < data->temp_passive) {
imx_set_alarm_temp(data, data->temp_passive);
- dev_dbg(&tz->device, "thermal alarm off: T < %lu\n",
+ dev_dbg(&tz->device, "thermal alarm off: T < %d\n",
data->alarm_temp / 1000);
}
}
if (*temp != data->last_temp) {
- dev_dbg(&tz->device, "millicelsius: %ld\n", *temp);
+ dev_dbg(&tz->device, "millicelsius: %d\n", *temp);
data->last_temp = *temp;
}
return 0;
}
-static int imx_get_crit_temp(struct thermal_zone_device *tz,
- unsigned long *temp)
+static int imx_get_crit_temp(struct thermal_zone_device *tz, int *temp)
{
struct imx_thermal_data *data = tz->devdata;
}
static int imx_get_trip_temp(struct thermal_zone_device *tz, int trip,
- unsigned long *temp)
+ int *temp)
{
struct imx_thermal_data *data = tz->devdata;
}
static int imx_set_trip_temp(struct thermal_zone_device *tz, int trip,
- unsigned long temp)
+ int temp)
{
struct imx_thermal_data *data = tz->devdata;
+ /* do not allow changing critical threshold */
if (trip == IMX_TRIP_CRITICAL)
return -EPERM;
- if (temp > IMX_TEMP_PASSIVE)
+ /* do not allow passive to be set higher than critical */
+ if (temp < 0 || temp > data->temp_critical)
return -EINVAL;
data->temp_passive = temp;
ret = thermal_zone_bind_cooling_device(tz, IMX_TRIP_PASSIVE, cdev,
THERMAL_NO_LIMIT,
- THERMAL_NO_LIMIT);
+ THERMAL_NO_LIMIT,
+ THERMAL_WEIGHT_DEFAULT);
if (ret) {
dev_err(&tz->device,
"binding zone %s with cdev %s failed:%d\n",
data->c1 = temp64;
data->c2 = n1 * data->c1 + 1000 * t1;
- /*
- * Set the default passive cooling trip point,
- * can be changed from userspace.
- */
- data->temp_passive = IMX_TEMP_PASSIVE;
+ /* use OTP for thermal grade */
+ ret = regmap_read(map, OCOTP_MEM0, &val);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to read temp grade: %d\n", ret);
+ return ret;
+ }
+
+ /* The maximum die temp is specified by the Temperature Grade */
+ switch ((val >> 6) & 0x3) {
+ case 0: /* Commercial (0 to 95C) */
+ data->temp_grade = "Commercial";
+ data->temp_max = 95000;
+ break;
+ case 1: /* Extended Commercial (-20 to 105C) */
+ data->temp_grade = "Extended Commercial";
+ data->temp_max = 105000;
+ break;
+ case 2: /* Industrial (-40 to 105C) */
+ data->temp_grade = "Industrial";
+ data->temp_max = 105000;
+ break;
+ case 3: /* Automotive (-40 to 125C) */
+ data->temp_grade = "Automotive";
+ data->temp_max = 125000;
+ break;
+ }
/*
- * The maximum die temperature set to 20 C higher than
- * IMX_TEMP_PASSIVE.
+ * Set the critical trip point at 5C under max
+ * Set the passive trip point at 10C under max (can change via sysfs)
*/
- data->temp_critical = 1000 * 20 + data->temp_passive;
+ data->temp_critical = data->temp_max - (1000 * 5);
+ data->temp_passive = data->temp_max - (1000 * 10);
return 0;
}
{
struct imx_thermal_data *data = dev;
- dev_dbg(&data->tz->device, "THERMAL ALARM: T > %lu\n",
+ dev_dbg(&data->tz->device, "THERMAL ALARM: T > %d\n",
data->alarm_temp / 1000);
thermal_zone_device_update(data->tz);
if (data->irq < 0)
return data->irq;
- ret = devm_request_threaded_irq(&pdev->dev, data->irq,
- imx_thermal_alarm_irq, imx_thermal_alarm_irq_thread,
- 0, "imx_thermal", data);
- if (ret < 0) {
- dev_err(&pdev->dev, "failed to request alarm irq: %d\n", ret);
- return ret;
- }
-
platform_set_drvdata(pdev, data);
ret = imx_get_sensor_data(pdev);
return ret;
}
+ dev_info(&pdev->dev, "%s CPU temperature grade - max:%dC"
+ " critical:%dC passive:%dC\n", data->temp_grade,
+ data->temp_max / 1000, data->temp_critical / 1000,
+ data->temp_passive / 1000);
+
/* Enable measurements at ~ 10 Hz */
regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
+ ret = devm_request_threaded_irq(&pdev->dev, data->irq,
+ imx_thermal_alarm_irq, imx_thermal_alarm_irq_thread,
+ 0, "imx_thermal", data);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to request alarm irq: %d\n", ret);
+ clk_disable_unprepare(data->thermal_clk);
+ thermal_zone_device_unregister(data->tz);
+ cpufreq_cooling_unregister(data->cdev);
+ return ret;
+ }
+
data->irq_enabled = true;
data->mode = THERMAL_DEVICE_ENABLED;
Code Review / kvmfornfv.git / blobdiff