--- /dev/null
+#ifndef _RTL819XU_HTTYPE_H_
+#define _RTL819XU_HTTYPE_H_
+
+//------------------------------------------------------------
+// The HT Capability element is present in beacons, association request,
+// reassociation request and probe response frames
+//------------------------------------------------------------
+
+//
+// Operation mode value
+//
+#define HT_OPMODE_NO_PROTECT 0
+#define HT_OPMODE_OPTIONAL 1
+#define HT_OPMODE_40MHZ_PROTECT 2
+#define HT_OPMODE_MIXED 3
+
+//
+// MIMO Power Save Settings
+//
+#define MIMO_PS_STATIC 0
+#define MIMO_PS_DYNAMIC 1
+#define MIMO_PS_NOLIMIT 3
+
+
+//
+// There should be 128 bits to cover all of the MCS rates. However, since
+// 8190 does not support too much rates, one integer is quite enough.
+//
+
+#define sHTCLng 4
+
+
+#define HT_SUPPORTED_MCS_1SS_BITMAP 0x000000ff
+#define HT_SUPPORTED_MCS_2SS_BITMAP 0x0000ff00
+#define HT_SUPPORTED_MCS_1SS_2SS_BITMAP HT_MCS_1SS_BITMAP|HT_MCS_1SS_2SS_BITMAP
+
+
+typedef enum _HT_MCS_RATE{
+ HT_MCS0 = 0x00000001,
+ HT_MCS1 = 0x00000002,
+ HT_MCS2 = 0x00000004,
+ HT_MCS3 = 0x00000008,
+ HT_MCS4 = 0x00000010,
+ HT_MCS5 = 0x00000020,
+ HT_MCS6 = 0x00000040,
+ HT_MCS7 = 0x00000080,
+ HT_MCS8 = 0x00000100,
+ HT_MCS9 = 0x00000200,
+ HT_MCS10 = 0x00000400,
+ HT_MCS11 = 0x00000800,
+ HT_MCS12 = 0x00001000,
+ HT_MCS13 = 0x00002000,
+ HT_MCS14 = 0x00004000,
+ HT_MCS15 = 0x00008000,
+ // Do not define MCS32 here although 8190 support MCS32
+} HT_MCS_RATE, *PHT_MCS_RATE;
+
+//
+// Represent Channel Width in HT Capabilities
+//
+typedef enum _HT_CHANNEL_WIDTH{
+ HT_CHANNEL_WIDTH_20 = 0,
+ HT_CHANNEL_WIDTH_20_40 = 1,
+}HT_CHANNEL_WIDTH, *PHT_CHANNEL_WIDTH;
+
+//
+// Represent Extension Channel Offset in HT Capabilities
+// This is available only in 40Mhz mode.
+//
+typedef enum _HT_EXTCHNL_OFFSET{
+ HT_EXTCHNL_OFFSET_NO_EXT = 0,
+ HT_EXTCHNL_OFFSET_UPPER = 1,
+ HT_EXTCHNL_OFFSET_NO_DEF = 2,
+ HT_EXTCHNL_OFFSET_LOWER = 3,
+}HT_EXTCHNL_OFFSET, *PHT_EXTCHNL_OFFSET;
+
+typedef enum _CHNLOP{
+ CHNLOP_NONE = 0, // No Action now
+ CHNLOP_SCAN = 1, // Scan in progress
+ CHNLOP_SWBW = 2, // Bandwidth switching in progress
+ CHNLOP_SWCHNL = 3, // Software Channel switching in progress
+} CHNLOP, *PCHNLOP;
+
+// Determine if the Channel Operation is in progress
+#define CHHLOP_IN_PROGRESS(_pHTInfo) \
+ ((_pHTInfo)->ChnlOp > CHNLOP_NONE) ? TRUE : FALSE
+
+/*
+typedef union _HT_CAPABILITY{
+ u16 ShortData;
+ u8 CharData[2];
+ struct
+ {
+ u16 AdvCoding:1;
+ u16 ChlWidth:1;
+ u16 MimoPwrSave:2;
+ u16 GreenField:1;
+ u16 ShortGI20Mhz:1;
+ u16 ShortGI40Mhz:1;
+ u16 STBC:1;
+ u16 BeamForm:1;
+ u16 DelayBA:1;
+ u16 MaxAMSDUSize:1;
+ u16 DssCCk:1;
+ u16 PSMP:1;
+ u16 Rsvd:3;
+ }Field;
+}HT_CAPABILITY, *PHT_CAPABILITY;
+
+typedef union _HT_CAPABILITY_MACPARA{
+ u8 ShortData;
+ u8 CharData[1];
+ struct
+ {
+ u8 MaxRxAMPDU:2;
+ u8 MPDUDensity:2;
+ u8 Rsvd:4;
+ }Field;
+}HT_CAPABILITY_MACPARA, *PHT_CAPABILITY_MACPARA;
+*/
+
+typedef enum _HT_ACTION{
+ ACT_RECOMMAND_WIDTH = 0,
+ ACT_MIMO_PWR_SAVE = 1,
+ ACT_PSMP = 2,
+ ACT_SET_PCO_PHASE = 3,
+ ACT_MIMO_CHL_MEASURE = 4,
+ ACT_RECIPROCITY_CORRECT = 5,
+ ACT_MIMO_CSI_MATRICS = 6,
+ ACT_MIMO_NOCOMPR_STEER = 7,
+ ACT_MIMO_COMPR_STEER = 8,
+ ACT_ANTENNA_SELECT = 9,
+} HT_ACTION, *PHT_ACTION;
+
+
+/* 2007/06/07 MH Define sub-carrier mode for 40MHZ. */
+typedef enum _HT_Bandwidth_40MHZ_Sub_Carrier{
+ SC_MODE_DUPLICATE = 0,
+ SC_MODE_LOWER = 1,
+ SC_MODE_UPPER = 2,
+ SC_MODE_FULL40MHZ = 3,
+}HT_BW40_SC_E;
+
+typedef struct _HT_CAPABILITY_ELE{
+
+ //HT capability info
+ u8 AdvCoding:1;
+ u8 ChlWidth:1;
+ u8 MimoPwrSave:2;
+ u8 GreenField:1;
+ u8 ShortGI20Mhz:1;
+ u8 ShortGI40Mhz:1;
+ u8 TxSTBC:1;
+ u8 RxSTBC:2;
+ u8 DelayBA:1;
+ u8 MaxAMSDUSize:1;
+ u8 DssCCk:1;
+ u8 PSMP:1;
+ u8 Rsvd1:1;
+ u8 LSigTxopProtect:1;
+
+ //MAC HT parameters info
+ u8 MaxRxAMPDUFactor:2;
+ u8 MPDUDensity:3;
+ u8 Rsvd2:3;
+
+ //Supported MCS set
+ u8 MCS[16];
+
+
+ //Extended HT Capability Info
+ u16 ExtHTCapInfo;
+
+ //TXBF Capabilities
+ u8 TxBFCap[4];
+
+ //Antenna Selection Capabilities
+ u8 ASCap;
+
+} __attribute__ ((packed)) HT_CAPABILITY_ELE, *PHT_CAPABILITY_ELE;
+
+//------------------------------------------------------------
+// The HT Information element is present in beacons
+// Only AP is required to include this element
+//------------------------------------------------------------
+
+typedef struct _HT_INFORMATION_ELE{
+ u8 ControlChl;
+
+ u8 ExtChlOffset:2;
+ u8 RecommemdedTxWidth:1;
+ u8 RIFS:1;
+ u8 PSMPAccessOnly:1;
+ u8 SrvIntGranularity:3;
+
+ u8 OptMode:2;
+ u8 NonGFDevPresent:1;
+ u8 Revd1:5;
+ u8 Revd2:8;
+
+ u8 Rsvd3:6;
+ u8 DualBeacon:1;
+ u8 DualCTSProtect:1;
+
+ u8 SecondaryBeacon:1;
+ u8 LSigTxopProtectFull:1;
+ u8 PcoActive:1;
+ u8 PcoPhase:1;
+ u8 Rsvd4:4;
+
+ u8 BasicMSC[16];
+} __attribute__ ((packed)) HT_INFORMATION_ELE, *PHT_INFORMATION_ELE;
+
+//
+// MIMO Power Save control field.
+// This is appear in MIMO Power Save Action Frame
+//
+typedef struct _MIMOPS_CTRL{
+ u8 MimoPsEnable:1;
+ u8 MimoPsMode:1;
+ u8 Reserved:6;
+} MIMOPS_CTRL, *PMIMOPS_CTRL;
+
+typedef enum _HT_SPEC_VER{
+ HT_SPEC_VER_IEEE = 0,
+ HT_SPEC_VER_EWC = 1,
+}HT_SPEC_VER, *PHT_SPEC_VER;
+
+typedef enum _HT_AGGRE_MODE_E{
+ HT_AGG_AUTO = 0,
+ HT_AGG_FORCE_ENABLE = 1,
+ HT_AGG_FORCE_DISABLE = 2,
+}HT_AGGRE_MODE_E, *PHT_AGGRE_MODE_E;
+
+//------------------------------------------------------------
+// The Data structure is used to keep HT related variables when card is
+// configured as non-AP STA mode. **Note** Current_xxx should be set
+// to default value in HTInitializeHTInfo()
+//------------------------------------------------------------
+
+typedef struct _RT_HIGH_THROUGHPUT{
+ u8 bEnableHT;
+ u8 bCurrentHTSupport;
+
+ u8 bRegBW40MHz; // Tx 40MHz channel capability
+ u8 bCurBW40MHz; // Tx 40MHz channel capability
+
+ u8 bRegShortGI40MHz; // Tx Short GI for 40Mhz
+ u8 bCurShortGI40MHz; // Tx Short GI for 40MHz
+
+ u8 bRegShortGI20MHz; // Tx Short GI for 20MHz
+ u8 bCurShortGI20MHz; // Tx Short GI for 20MHz
+
+ u8 bRegSuppCCK; // Tx CCK rate capability
+ u8 bCurSuppCCK; // Tx CCK rate capability
+
+ // 802.11n spec version for "peer"
+ HT_SPEC_VER ePeerHTSpecVer;
+
+
+ // HT related information for "Self"
+ HT_CAPABILITY_ELE SelfHTCap; // This is HT cap element sent to peer STA, which also indicate HT Rx capabilities.
+ HT_INFORMATION_ELE SelfHTInfo; // This is HT info element sent to peer STA, which also indicate HT Rx capabilities.
+
+ // HT related information for "Peer"
+ u8 PeerHTCapBuf[32];
+ u8 PeerHTInfoBuf[32];
+
+
+ // A-MSDU related
+ u8 bAMSDU_Support; // This indicates Tx A-MSDU capability
+ u16 nAMSDU_MaxSize; // This indicates Tx A-MSDU capability
+ u8 bCurrent_AMSDU_Support; // This indicates Tx A-MSDU capability
+ u16 nCurrent_AMSDU_MaxSize; // This indicates Tx A-MSDU capability
+
+
+ // AMPDU related <2006.08.10 Emily>
+ u8 bAMPDUEnable; // This indicate Tx A-MPDU capability
+ u8 bCurrentAMPDUEnable; // This indicate Tx A-MPDU capability
+ u8 AMPDU_Factor; // This indicate Tx A-MPDU capability
+ u8 CurrentAMPDUFactor; // This indicate Tx A-MPDU capability
+ u8 MPDU_Density; // This indicate Tx A-MPDU capability
+ u8 CurrentMPDUDensity; // This indicate Tx A-MPDU capability
+
+ // Forced A-MPDU enable
+ HT_AGGRE_MODE_E ForcedAMPDUMode;
+ u8 ForcedAMPDUFactor;
+ u8 ForcedMPDUDensity;
+
+ // Forced A-MSDU enable
+ HT_AGGRE_MODE_E ForcedAMSDUMode;
+ u16 ForcedAMSDUMaxSize;
+
+ u8 bForcedShortGI;
+
+ u8 CurrentOpMode;
+
+ // MIMO PS related
+ u8 SelfMimoPs;
+ u8 PeerMimoPs;
+
+ // 40MHz Channel Offset settings.
+ HT_EXTCHNL_OFFSET CurSTAExtChnlOffset;
+ u8 bCurTxBW40MHz; // If we use 40 MHz to Tx
+ u8 PeerBandwidth;
+
+ // For Bandwidth Switching
+ u8 bSwBwInProgress;
+ CHNLOP ChnlOp; // software switching channel in progress. By Bruce, 2008-02-15.
+ u8 SwBwStep;
+ //struct timer_list SwBwTimer; //moved to ieee80211_device. as timer_list need include some header file here.
+
+ // For Realtek proprietary A-MPDU factor for aggregation
+ u8 bRegRT2RTAggregation;
+ u8 bCurrentRT2RTAggregation;
+ u8 bCurrentRT2RTLongSlotTime;
+ u8 szRT2RTAggBuffer[10];
+
+ // Rx Reorder control
+ u8 bRegRxReorderEnable;
+ u8 bCurRxReorderEnable;
+ u8 RxReorderWinSize;
+ u8 RxReorderPendingTime;
+ u16 RxReorderDropCounter;
+
+#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE
+ u8 UsbTxAggrNum;
+#endif
+#ifdef USB_RX_AGGREGATION_SUPPORT
+ u8 UsbRxFwAggrEn;
+ u8 UsbRxFwAggrPageNum;
+ u8 UsbRxFwAggrPacketNum;
+ u8 UsbRxFwAggrTimeout;
+#endif
+
+ // Add for Broadcom(Linksys) IOT. Joseph
+ u8 bIsPeerBcm;
+
+ // For IOT issue.
+ u8 IOTPeer;
+ u32 IOTAction;
+} __attribute__ ((packed)) RT_HIGH_THROUGHPUT, *PRT_HIGH_THROUGHPUT;
+
+
+//------------------------------------------------------------
+// The Data structure is used to keep HT related variable for "each Sta"
+// when card is configured as "AP mode"
+//------------------------------------------------------------
+
+typedef struct _RT_HTINFO_STA_ENTRY{
+ u8 bEnableHT;
+
+ u8 bSupportCck;
+
+ u16 AMSDU_MaxSize;
+
+ u8 AMPDU_Factor;
+ u8 MPDU_Density;
+
+ u8 HTHighestOperaRate;
+
+ u8 bBw40MHz;
+
+ u8 MimoPs;
+
+ u8 McsRateSet[16];
+
+
+}RT_HTINFO_STA_ENTRY, *PRT_HTINFO_STA_ENTRY;
+
+
+
+
+
+//------------------------------------------------------------
+// The Data structure is used to keep HT related variable for "each AP"
+// when card is configured as "STA mode"
+//------------------------------------------------------------
+
+typedef struct _BSS_HT{
+
+ u8 bdSupportHT;
+
+ // HT related elements
+ u8 bdHTCapBuf[32];
+ u16 bdHTCapLen;
+ u8 bdHTInfoBuf[32];
+ u16 bdHTInfoLen;
+
+ HT_SPEC_VER bdHTSpecVer;
+ //HT_CAPABILITY_ELE bdHTCapEle;
+ //HT_INFORMATION_ELE bdHTInfoEle;
+
+ u8 bdRT2RTAggregation;
+ u8 bdRT2RTLongSlotTime;
+} __attribute__ ((packed)) BSS_HT, *PBSS_HT;
+
+typedef struct _MIMO_RSSI{
+ u32 EnableAntenna;
+ u32 AntennaA;
+ u32 AntennaB;
+ u32 AntennaC;
+ u32 AntennaD;
+ u32 Average;
+}MIMO_RSSI, *PMIMO_RSSI;
+
+typedef struct _MIMO_EVM{
+ u32 EVM1;
+ u32 EVM2;
+}MIMO_EVM, *PMIMO_EVM;
+
+typedef struct _FALSE_ALARM_STATISTICS{
+ u32 Cnt_Parity_Fail;
+ u32 Cnt_Rate_Illegal;
+ u32 Cnt_Crc8_fail;
+ u32 Cnt_all;
+}FALSE_ALARM_STATISTICS, *PFALSE_ALARM_STATISTICS;
+
+
+extern u8 MCS_FILTER_ALL[16];
+extern u8 MCS_FILTER_1SS[16];
+
+/* 2007/07/11 MH Modify the macro. Becaus STA may link with a N-AP. If we set
+ STA in A/B/G mode and AP is still in N mode. The macro will be wrong. We have
+ to add a macro to judge wireless mode. */
+#define PICK_RATE(_nLegacyRate, _nMcsRate) \
+ (_nMcsRate==0)?(_nLegacyRate&0x7f):(_nMcsRate)
+/* 2007/07/12 MH We only define legacy and HT wireless mode now. */
+#define LEGACY_WIRELESS_MODE IEEE_MODE_MASK
+
+#define CURRENT_RATE(WirelessMode, LegacyRate, HTRate) \
+ ((WirelessMode & (LEGACY_WIRELESS_MODE))!=0)?\
+ (LegacyRate):\
+ (PICK_RATE(LegacyRate, HTRate))
+
+
+
+// MCS Bw 40 {1~7, 12~15,32}
+#define RATE_ADPT_1SS_MASK 0xFF
+#define RATE_ADPT_2SS_MASK 0xF0 //Skip MCS8~11 because mcs7 > mcs6, 9, 10, 11. 2007.01.16 by Emily
+#define RATE_ADPT_MCS32_MASK 0x01
+
+#define IS_11N_MCS_RATE(rate) (rate&0x80)
+
+typedef enum _HT_AGGRE_SIZE{
+ HT_AGG_SIZE_8K = 0,
+ HT_AGG_SIZE_16K = 1,
+ HT_AGG_SIZE_32K = 2,
+ HT_AGG_SIZE_64K = 3,
+}HT_AGGRE_SIZE_E, *PHT_AGGRE_SIZE_E;
+
+/* Indicate different AP vendor for IOT issue */
+typedef enum _HT_IOT_PEER
+{
+ HT_IOT_PEER_UNKNOWN = 0,
+ HT_IOT_PEER_REALTEK = 1,
+ HT_IOT_PEER_BROADCOM = 2,
+ HT_IOT_PEER_RALINK = 3,
+ HT_IOT_PEER_ATHEROS = 4,
+ HT_IOT_PEER_CISCO= 5,
+ HT_IOT_PEER_MAX = 6
+}HT_IOT_PEER_E, *PHTIOT_PEER_E;
+
+//
+// IOT Action for different AP
+//
+typedef enum _HT_IOT_ACTION{
+ HT_IOT_ACT_TX_USE_AMSDU_4K = 0x00000001,
+ HT_IOT_ACT_TX_USE_AMSDU_8K = 0x00000002,
+ HT_IOT_ACT_DISABLE_MCS14 = 0x00000004,
+ HT_IOT_ACT_DISABLE_MCS15 = 0x00000008,
+ HT_IOT_ACT_DISABLE_ALL_2SS = 0x00000010,
+ HT_IOT_ACT_DISABLE_EDCA_TURBO = 0x00000020,
+ HT_IOT_ACT_MGNT_USE_CCK_6M = 0x00000040,
+ HT_IOT_ACT_CDD_FSYNC = 0x00000080,
+ HT_IOT_ACT_PURE_N_MODE = 0x00000100,
+ HT_IOT_ACT_FORCED_CTS2SELF = 0x00000200,
+}HT_IOT_ACTION_E, *PHT_IOT_ACTION_E;
+
+#endif //_RTL819XU_HTTYPE_H_
Code Review / kvmfornfv.git / blobdiff