#ifndef __RTL8188E_SPEC_H__
#define __RTL8188E_SPEC_H__
-#ifndef BIT
-#define BIT(x) (1 << (x))
-#endif
-
-#define BIT0 0x00000001
-#define BIT1 0x00000002
-#define BIT2 0x00000004
-#define BIT3 0x00000008
-#define BIT4 0x00000010
-#define BIT5 0x00000020
-#define BIT6 0x00000040
-#define BIT7 0x00000080
-#define BIT8 0x00000100
-#define BIT9 0x00000200
-#define BIT10 0x00000400
-#define BIT11 0x00000800
-#define BIT12 0x00001000
-#define BIT13 0x00002000
-#define BIT14 0x00004000
-#define BIT15 0x00008000
-#define BIT16 0x00010000
-#define BIT17 0x00020000
-#define BIT18 0x00040000
-#define BIT19 0x00080000
-#define BIT20 0x00100000
-#define BIT21 0x00200000
-#define BIT22 0x00400000
-#define BIT23 0x00800000
-#define BIT24 0x01000000
-#define BIT25 0x02000000
-#define BIT26 0x04000000
-#define BIT27 0x08000000
-#define BIT28 0x10000000
-#define BIT29 0x20000000
-#define BIT30 0x40000000
-#define BIT31 0x80000000
-
/* 8192C Regsiter offset definition */
#define HAL_PS_TIMER_INT_DELAY 50 /* 50 microseconds */
#define MAX_MSS_DENSITY_1T 0x0A
/* EEPROM enable when set 1 */
-#define CmdEEPROM_En BIT5
+#define CmdEEPROM_En BIT(5)
/* System EEPROM select, 0: boot from E-FUSE, 1: The EEPROM used is 9346 */
-#define CmdEERPOMSEL BIT4
-#define Cmd9346CR_9356SEL BIT4
+#define CmdEERPOMSEL BIT(4)
+#define Cmd9346CR_9356SEL BIT(4)
/* 8192C GPIO MUX Configuration Register (offset 0x40, 4 byte) */
#define GPIOSEL_GPIO 0
-#define GPIOSEL_ENBT BIT5
+#define GPIOSEL_ENBT BIT(5)
/* 8192C GPIO PIN Control Register (offset 0x44, 4 byte) */
/* GPIO pins input value */
#define GPIO_MOD (REG_GPIO_PIN_CTRL+3)
/* 8723/8188E Host System Interrupt Mask Register (offset 0x58, 32 byte) */
-#define HSIMR_GPIO12_0_INT_EN BIT0
-#define HSIMR_SPS_OCP_INT_EN BIT5
-#define HSIMR_RON_INT_EN BIT6
-#define HSIMR_PDN_INT_EN BIT7
-#define HSIMR_GPIO9_INT_EN BIT25
+#define HSIMR_GPIO12_0_INT_EN BIT(0)
+#define HSIMR_SPS_OCP_INT_EN BIT(5)
+#define HSIMR_RON_INT_EN BIT(6)
+#define HSIMR_PDN_INT_EN BIT(7)
+#define HSIMR_GPIO9_INT_EN BIT(25)
/* 8723/8188E Host System Interrupt Status Register (offset 0x5C, 32 byte) */
-#define HSISR_GPIO12_0_INT BIT0
-#define HSISR_SPS_OCP_INT BIT5
-#define HSISR_RON_INT_EN BIT6
-#define HSISR_PDNINT BIT7
-#define HSISR_GPIO9_INT BIT25
+#define HSISR_GPIO12_0_INT BIT(0)
+#define HSISR_SPS_OCP_INT BIT(5)
+#define HSISR_RON_INT_EN BIT(6)
+#define HSISR_PDNINT BIT(7)
+#define HSISR_GPIO9_INT BIT(25)
/* 8192C (MSR) Media Status Register (Offset 0x4C, 8 bits) */
/*
/* 88E Driver Initialization Offload REG_FDHM0(Offset 0x88, 8 bits) */
/* IOL config for REG_FDHM0(Reg0x88) */
-#define CMD_INIT_LLT BIT0
-#define CMD_READ_EFUSE_MAP BIT1
-#define CMD_EFUSE_PATCH BIT2
-#define CMD_IOCONFIG BIT3
-#define CMD_INIT_LLT_ERR BIT4
-#define CMD_READ_EFUSE_MAP_ERR BIT5
-#define CMD_EFUSE_PATCH_ERR BIT6
-#define CMD_IOCONFIG_ERR BIT7
+#define CMD_INIT_LLT BIT(0)
+#define CMD_READ_EFUSE_MAP BIT(1)
+#define CMD_EFUSE_PATCH BIT(2)
+#define CMD_IOCONFIG BIT(3)
+#define CMD_INIT_LLT_ERR BIT(4)
+#define CMD_READ_EFUSE_MAP_ERR BIT(5)
+#define CMD_EFUSE_PATCH_ERR BIT(6)
+#define CMD_IOCONFIG_ERR BIT(7)
/* 6. Adaptive Control Registers (Offset: 0x0160 - 0x01CF) */
/* 8192C Response Rate Set Register (offset 0x181, 24bits) */
-#define RRSR_1M BIT0
-#define RRSR_2M BIT1
-#define RRSR_5_5M BIT2
-#define RRSR_11M BIT3
-#define RRSR_6M BIT4
-#define RRSR_9M BIT5
-#define RRSR_12M BIT6
-#define RRSR_18M BIT7
-#define RRSR_24M BIT8
-#define RRSR_36M BIT9
-#define RRSR_48M BIT10
-#define RRSR_54M BIT11
-#define RRSR_MCS0 BIT12
-#define RRSR_MCS1 BIT13
-#define RRSR_MCS2 BIT14
-#define RRSR_MCS3 BIT15
-#define RRSR_MCS4 BIT16
-#define RRSR_MCS5 BIT17
-#define RRSR_MCS6 BIT18
-#define RRSR_MCS7 BIT19
+#define RRSR_1M BIT(0)
+#define RRSR_2M BIT(1)
+#define RRSR_5_5M BIT(2)
+#define RRSR_11M BIT(3)
+#define RRSR_6M BIT(4)
+#define RRSR_9M BIT(5)
+#define RRSR_12M BIT(6)
+#define RRSR_18M BIT(7)
+#define RRSR_24M BIT(8)
+#define RRSR_36M BIT(9)
+#define RRSR_48M BIT(10)
+#define RRSR_54M BIT(11)
+#define RRSR_MCS0 BIT(12)
+#define RRSR_MCS1 BIT(13)
+#define RRSR_MCS2 BIT(14)
+#define RRSR_MCS3 BIT(15)
+#define RRSR_MCS4 BIT(16)
+#define RRSR_MCS5 BIT(17)
+#define RRSR_MCS6 BIT(18)
+#define RRSR_MCS7 BIT(19)
/* 8192C Response Rate Set Register (offset 0x1BF, 8bits) */
/* WOL bit information */
-#define HAL92C_WOL_PTK_UPDATE_EVENT BIT0
-#define HAL92C_WOL_GTK_UPDATE_EVENT BIT1
+#define HAL92C_WOL_PTK_UPDATE_EVENT BIT(0)
+#define HAL92C_WOL_GTK_UPDATE_EVENT BIT(1)
/* 8192C BW_OPMODE bits (Offset 0x203, 8bit) */
-#define BW_OPMODE_20MHZ BIT2
-#define BW_OPMODE_5G BIT1
+#define BW_OPMODE_20MHZ BIT(2)
+#define BW_OPMODE_5G BIT(1)
/* 8192C CAM Config Setting (offset 0x250, 1 byte) */
-#define CAM_VALID BIT15
+#define CAM_VALID BIT(15)
#define CAM_NOTVALID 0x0000
-#define CAM_USEDK BIT5
+#define CAM_USEDK BIT(5)
#define CAM_CONTENT_COUNT 8
#define CAM_CONFIG_USEDK true
#define CAM_CONFIG_NO_USEDK false
-#define CAM_WRITE BIT16
+#define CAM_WRITE BIT(16)
#define CAM_READ 0x00000000
-#define CAM_POLLINIG BIT31
+#define CAM_POLLINIG BIT(31)
#define SCR_UseDK 0x01
#define SCR_TxSecEnable 0x02
#define SCR_RxSecEnable 0x04
/* 10. Power Save Control Registers (Offset: 0x0260 - 0x02DF) */
-#define WOW_PMEN BIT0 /* Power management Enable. */
-#define WOW_WOMEN BIT1 /* WoW function on or off. */
-#define WOW_MAGIC BIT2 /* Magic packet */
-#define WOW_UWF BIT3 /* Unicast Wakeup frame. */
+#define WOW_PMEN BIT(0) /* Power management Enable. */
+#define WOW_WOMEN BIT(1) /* WoW function on or off. */
+#define WOW_MAGIC BIT(2) /* Magic packet */
+#define WOW_UWF BIT(3) /* Unicast Wakeup frame. */
/* 12. Host Interrupt Status Registers (Offset: 0x0300 - 0x030F) */
/* 8188 IMR/ISR bits */
#define IMR_DISABLED_88E 0x0
/* IMR DW0(0x0060-0063) Bit 0-31 */
-#define IMR_TXCCK_88E BIT30 /* TXRPT interrupt when CCX bit of the packet is set */
-#define IMR_PSTIMEOUT_88E BIT29 /* Power Save Time Out Interrupt */
-#define IMR_GTINT4_88E BIT28 /* When GTIMER4 expires, this bit is set to 1 */
-#define IMR_GTINT3_88E BIT27 /* When GTIMER3 expires, this bit is set to 1 */
-#define IMR_TBDER_88E BIT26 /* Transmit Beacon0 Error */
-#define IMR_TBDOK_88E BIT25 /* Transmit Beacon0 OK */
-#define IMR_TSF_BIT32_TOGGLE_88E BIT24 /* TSF Timer BIT32 toggle indication interrupt */
-#define IMR_BCNDMAINT0_88E BIT20 /* Beacon DMA Interrupt 0 */
-#define IMR_BCNDERR0_88E BIT16 /* Beacon Queue DMA Error 0 */
-#define IMR_HSISR_IND_ON_INT_88E BIT15 /* HSISR Indicator (HSIMR & HSISR is true, this bit is set to 1) */
-#define IMR_BCNDMAINT_E_88E BIT14 /* Beacon DMA Interrupt Extension for Win7 */
-#define IMR_ATIMEND_88E BIT12 /* CTWidnow End or ATIM Window End */
-#define IMR_HISR1_IND_INT_88E BIT11 /* HISR1 Indicator (HISR1 & HIMR1 is true, this bit is set to 1) */
-#define IMR_C2HCMD_88E BIT10 /* CPU to Host Command INT Status, Write 1 clear */
-#define IMR_CPWM2_88E BIT9 /* CPU power Mode exchange INT Status, Write 1 clear */
-#define IMR_CPWM_88E BIT8 /* CPU power Mode exchange INT Status, Write 1 clear */
-#define IMR_HIGHDOK_88E BIT7 /* High Queue DMA OK */
-#define IMR_MGNTDOK_88E BIT6 /* Management Queue DMA OK */
-#define IMR_BKDOK_88E BIT5 /* AC_BK DMA OK */
-#define IMR_BEDOK_88E BIT4 /* AC_BE DMA OK */
-#define IMR_VIDOK_88E BIT3 /* AC_VI DMA OK */
-#define IMR_VODOK_88E BIT2 /* AC_VO DMA OK */
-#define IMR_RDU_88E BIT1 /* Rx Descriptor Unavailable */
-#define IMR_ROK_88E BIT0 /* Receive DMA OK */
+#define IMR_TXCCK_88E BIT(30) /* TXRPT interrupt when CCX bit of the packet is set */
+#define IMR_PSTIMEOUT_88E BIT(29) /* Power Save Time Out Interrupt */
+#define IMR_GTINT4_88E BIT(28) /* When GTIMER4 expires, this bit is set to 1 */
+#define IMR_GTINT3_88E BIT(27) /* When GTIMER3 expires, this bit is set to 1 */
+#define IMR_TBDER_88E BIT(26) /* Transmit Beacon0 Error */
+#define IMR_TBDOK_88E BIT(25) /* Transmit Beacon0 OK */
+#define IMR_TSF_BIT32_TOGGLE_88E BIT(24) /* TSF Timer BIT32 toggle indication interrupt */
+#define IMR_BCNDMAINT0_88E BIT(20) /* Beacon DMA Interrupt 0 */
+#define IMR_BCNDERR0_88E BIT(16) /* Beacon Queue DMA Error 0 */
+#define IMR_HSISR_IND_ON_INT_88E BIT(15) /* HSISR Indicator (HSIMR & HSISR is true, this bit is set to 1) */
+#define IMR_BCNDMAINT_E_88E BIT(14) /* Beacon DMA Interrupt Extension for Win7 */
+#define IMR_ATIMEND_88E BIT(12) /* CTWidnow End or ATIM Window End */
+#define IMR_HISR1_IND_INT_88E BIT(11) /* HISR1 Indicator (HISR1 & HIMR1 is true, this bit is set to 1) */
+#define IMR_C2HCMD_88E BIT(10) /* CPU to Host Command INT Status, Write 1 clear */
+#define IMR_CPWM2_88E BIT(9) /* CPU power Mode exchange INT Status, Write 1 clear */
+#define IMR_CPWM_88E BIT(8) /* CPU power Mode exchange INT Status, Write 1 clear */
+#define IMR_HIGHDOK_88E BIT(7) /* High Queue DMA OK */
+#define IMR_MGNTDOK_88E BIT(6) /* Management Queue DMA OK */
+#define IMR_BKDOK_88E BIT(5) /* AC_BK DMA OK */
+#define IMR_BEDOK_88E BIT(4) /* AC_BE DMA OK */
+#define IMR_VIDOK_88E BIT(3) /* AC_VI DMA OK */
+#define IMR_VODOK_88E BIT(2) /* AC_VO DMA OK */
+#define IMR_RDU_88E BIT(1) /* Rx Descriptor Unavailable */
+#define IMR_ROK_88E BIT(0) /* Receive DMA OK */
/* IMR DW1(0x00B4-00B7) Bit 0-31 */
-#define IMR_BCNDMAINT7_88E BIT27 /* Beacon DMA Interrupt 7 */
-#define IMR_BCNDMAINT6_88E BIT26 /* Beacon DMA Interrupt 6 */
-#define IMR_BCNDMAINT5_88E BIT25 /* Beacon DMA Interrupt 5 */
-#define IMR_BCNDMAINT4_88E BIT24 /* Beacon DMA Interrupt 4 */
-#define IMR_BCNDMAINT3_88E BIT23 /* Beacon DMA Interrupt 3 */
-#define IMR_BCNDMAINT2_88E BIT22 /* Beacon DMA Interrupt 2 */
-#define IMR_BCNDMAINT1_88E BIT21 /* Beacon DMA Interrupt 1 */
-#define IMR_BCNDERR7_88E BIT20 /* Beacon DMA Error Int 7 */
-#define IMR_BCNDERR6_88E BIT19 /* Beacon DMA Error Int 6 */
-#define IMR_BCNDERR5_88E BIT18 /* Beacon DMA Error Int 5 */
-#define IMR_BCNDERR4_88E BIT17 /* Beacon DMA Error Int 4 */
-#define IMR_BCNDERR3_88E BIT16 /* Beacon DMA Error Int 3 */
-#define IMR_BCNDERR2_88E BIT15 /* Beacon DMA Error Int 2 */
-#define IMR_BCNDERR1_88E BIT14 /* Beacon DMA Error Int 1 */
-#define IMR_ATIMEND_E_88E BIT13 /* ATIM Window End Ext for Win7 */
-#define IMR_TXERR_88E BIT11 /* Tx Err Flag Int Status, write 1 clear. */
-#define IMR_RXERR_88E BIT10 /* Rx Err Flag INT Status, Write 1 clear */
-#define IMR_TXFOVW_88E BIT9 /* Transmit FIFO Overflow */
-#define IMR_RXFOVW_88E BIT8 /* Receive FIFO Overflow */
+#define IMR_BCNDMAINT7_88E BIT(27) /* Beacon DMA Interrupt 7 */
+#define IMR_BCNDMAINT6_88E BIT(26) /* Beacon DMA Interrupt 6 */
+#define IMR_BCNDMAINT5_88E BIT(25) /* Beacon DMA Interrupt 5 */
+#define IMR_BCNDMAINT4_88E BIT(24) /* Beacon DMA Interrupt 4 */
+#define IMR_BCNDMAINT3_88E BIT(23) /* Beacon DMA Interrupt 3 */
+#define IMR_BCNDMAINT2_88E BIT(22) /* Beacon DMA Interrupt 2 */
+#define IMR_BCNDMAINT1_88E BIT(21) /* Beacon DMA Interrupt 1 */
+#define IMR_BCNDERR7_88E BIT(20) /* Beacon DMA Error Int 7 */
+#define IMR_BCNDERR6_88E BIT(19) /* Beacon DMA Error Int 6 */
+#define IMR_BCNDERR5_88E BIT(18) /* Beacon DMA Error Int 5 */
+#define IMR_BCNDERR4_88E BIT(17) /* Beacon DMA Error Int 4 */
+#define IMR_BCNDERR3_88E BIT(16) /* Beacon DMA Error Int 3 */
+#define IMR_BCNDERR2_88E BIT(15) /* Beacon DMA Error Int 2 */
+#define IMR_BCNDERR1_88E BIT(14) /* Beacon DMA Error Int 1 */
+#define IMR_ATIMEND_E_88E BIT(13) /* ATIM Window End Ext for Win7 */
+#define IMR_TXERR_88E BIT(11) /* Tx Err Flag Int Status, write 1 clear. */
+#define IMR_RXERR_88E BIT(10) /* Rx Err Flag INT Status, Write 1 clear */
+#define IMR_TXFOVW_88E BIT(9) /* Transmit FIFO Overflow */
+#define IMR_RXFOVW_88E BIT(8) /* Receive FIFO Overflow */
#define HAL_NIC_UNPLUG_ISR 0xFFFFFFFF /* The value when the NIC is unplugged for PCI. */
/* the correct arragement is VO - Bit0, VI - Bit1, BE - Bit2,
* and BK - Bit3. */
/* 8723 and 88E may be not correct either in the earlier version. */
-#define StopBecon BIT6
-#define StopHigh BIT5
-#define StopMgt BIT4
-#define StopBK BIT3
-#define StopBE BIT2
-#define StopVI BIT1
-#define StopVO BIT0
+#define StopBecon BIT(6)
+#define StopHigh BIT(5)
+#define StopMgt BIT(4)
+#define StopBK BIT(3)
+#define StopBE BIT(2)
+#define StopVI BIT(1)
+#define StopVO BIT(0)
/* 8192C (RCR) Receive Configuration Register(Offset 0x608, 32 bits) */
-#define RCR_APPFCS BIT31 /* WMAC append FCS after payload */
-#define RCR_APP_MIC BIT30
-#define RCR_APP_PHYSTS BIT28
-#define RCR_APP_ICV BIT29
-#define RCR_APP_PHYST_RXFF BIT28
-#define RCR_APP_BA_SSN BIT27 /* Accept BA SSN */
-#define RCR_ENMBID BIT24 /* Enable Multiple BssId. */
-#define RCR_LSIGEN BIT23
-#define RCR_MFBEN BIT22
-#define RCR_HTC_LOC_CTRL BIT14 /* MFC<--HTC=1 MFC-->HTC=0 */
-#define RCR_AMF BIT13 /* Accept management type frame */
-#define RCR_ACF BIT12 /* Accept control type frame */
-#define RCR_ADF BIT11 /* Accept data type frame */
-#define RCR_AICV BIT9 /* Accept ICV error packet */
-#define RCR_ACRC32 BIT8 /* Accept CRC32 error packet */
-#define RCR_CBSSID_BCN BIT7 /* Accept BSSID match packet
+#define RCR_APPFCS BIT(31) /* WMAC append FCS after payload */
+#define RCR_APP_MIC BIT(30)
+#define RCR_APP_PHYSTS BIT(28)
+#define RCR_APP_ICV BIT(29)
+#define RCR_APP_PHYST_RXFF BIT(28)
+#define RCR_APP_BA_SSN BIT(27) /* Accept BA SSN */
+#define RCR_ENMBID BIT(24) /* Enable Multiple BssId. */
+#define RCR_LSIGEN BIT(23)
+#define RCR_MFBEN BIT(22)
+#define RCR_HTC_LOC_CTRL BIT(14) /* MFC<--HTC=1 MFC-->HTC=0 */
+#define RCR_AMF BIT(13) /* Accept management type frame */
+#define RCR_ACF BIT(12) /* Accept control type frame */
+#define RCR_ADF BIT(11) /* Accept data type frame */
+#define RCR_AICV BIT(9) /* Accept ICV error packet */
+#define RCR_ACRC32 BIT(8) /* Accept CRC32 error packet */
+#define RCR_CBSSID_BCN BIT(7) /* Accept BSSID match packet
* (Rx beacon, probe rsp) */
-#define RCR_CBSSID_DATA BIT6 /* Accept BSSID match (Data)*/
+#define RCR_CBSSID_DATA BIT(6) /* Accept BSSID match (Data)*/
#define RCR_CBSSID RCR_CBSSID_DATA /* Accept BSSID match */
-#define RCR_APWRMGT BIT5 /* Accept power management pkt*/
-#define RCR_ADD3 BIT4 /* Accept address 3 match pkt */
-#define RCR_AB BIT3 /* Accept broadcast packet */
-#define RCR_AM BIT2 /* Accept multicast packet */
-#define RCR_APM BIT1 /* Accept physical match pkt */
-#define RCR_AAP BIT0 /* Accept all unicast packet */
+#define RCR_APWRMGT BIT(5) /* Accept power management pkt*/
+#define RCR_ADD3 BIT(4) /* Accept address 3 match pkt */
+#define RCR_AB BIT(3) /* Accept broadcast packet */
+#define RCR_AM BIT(2) /* Accept multicast packet */
+#define RCR_APM BIT(1) /* Accept physical match pkt */
+#define RCR_AAP BIT(0) /* Accept all unicast packet */
#define RCR_MXDMA_OFFSET 8
#define RCR_FIFO_OFFSET 13
#define SDIO_HIMR_DISABLED 0
/* RTL8188E SDIO Host Interrupt Mask Register */
-#define SDIO_HIMR_RX_REQUEST_MSK BIT0
-#define SDIO_HIMR_AVAL_MSK BIT1
-#define SDIO_HIMR_TXERR_MSK BIT2
-#define SDIO_HIMR_RXERR_MSK BIT3
-#define SDIO_HIMR_TXFOVW_MSK BIT4
-#define SDIO_HIMR_RXFOVW_MSK BIT5
-#define SDIO_HIMR_TXBCNOK_MSK BIT6
-#define SDIO_HIMR_TXBCNERR_MSK BIT7
-#define SDIO_HIMR_BCNERLY_INT_MSK BIT16
-#define SDIO_HIMR_C2HCMD_MSK BIT17
-#define SDIO_HIMR_CPWM1_MSK BIT18
-#define SDIO_HIMR_CPWM2_MSK BIT19
-#define SDIO_HIMR_HSISR_IND_MSK BIT20
-#define SDIO_HIMR_GTINT3_IND_MSK BIT21
-#define SDIO_HIMR_GTINT4_IND_MSK BIT22
-#define SDIO_HIMR_PSTIMEOUT_MSK BIT23
-#define SDIO_HIMR_OCPINT_MSK BIT24
-#define SDIO_HIMR_ATIMEND_MSK BIT25
-#define SDIO_HIMR_ATIMEND_E_MSK BIT26
-#define SDIO_HIMR_CTWEND_MSK BIT27
+#define SDIO_HIMR_RX_REQUEST_MSK BIT(0)
+#define SDIO_HIMR_AVAL_MSK BIT(1)
+#define SDIO_HIMR_TXERR_MSK BIT(2)
+#define SDIO_HIMR_RXERR_MSK BIT(3)
+#define SDIO_HIMR_TXFOVW_MSK BIT(4)
+#define SDIO_HIMR_RXFOVW_MSK BIT(5)
+#define SDIO_HIMR_TXBCNOK_MSK BIT(6)
+#define SDIO_HIMR_TXBCNERR_MSK BIT(7)
+#define SDIO_HIMR_BCNERLY_INT_MSK BIT(16)
+#define SDIO_HIMR_C2HCMD_MSK BIT(17)
+#define SDIO_HIMR_CPWM1_MSK BIT(18)
+#define SDIO_HIMR_CPWM2_MSK BIT(19)
+#define SDIO_HIMR_HSISR_IND_MSK BIT(20)
+#define SDIO_HIMR_GTINT3_IND_MSK BIT(21)
+#define SDIO_HIMR_GTINT4_IND_MSK BIT(22)
+#define SDIO_HIMR_PSTIMEOUT_MSK BIT(23)
+#define SDIO_HIMR_OCPINT_MSK BIT(24)
+#define SDIO_HIMR_ATIMEND_MSK BIT(25)
+#define SDIO_HIMR_ATIMEND_E_MSK BIT(26)
+#define SDIO_HIMR_CTWEND_MSK BIT(27)
/* RTL8188E SDIO Specific */
-#define SDIO_HIMR_MCU_ERR_MSK BIT28
-#define SDIO_HIMR_TSF_BIT32_TOGGLE_MSK BIT29
+#define SDIO_HIMR_MCU_ERR_MSK BIT(28)
+#define SDIO_HIMR_TSF_BIT32_TOGGLE_MSK BIT(29)
/* SDIO Host Interrupt Service Routine */
-#define SDIO_HISR_RX_REQUEST BIT0
-#define SDIO_HISR_AVAL BIT1
-#define SDIO_HISR_TXERR BIT2
-#define SDIO_HISR_RXERR BIT3
-#define SDIO_HISR_TXFOVW BIT4
-#define SDIO_HISR_RXFOVW BIT5
-#define SDIO_HISR_TXBCNOK BIT6
-#define SDIO_HISR_TXBCNERR BIT7
-#define SDIO_HISR_BCNERLY_INT BIT16
-#define SDIO_HISR_C2HCMD BIT17
-#define SDIO_HISR_CPWM1 BIT18
-#define SDIO_HISR_CPWM2 BIT19
-#define SDIO_HISR_HSISR_IND BIT20
-#define SDIO_HISR_GTINT3_IND BIT21
-#define SDIO_HISR_GTINT4_IND BIT22
-#define SDIO_HISR_PSTIME BIT23
-#define SDIO_HISR_OCPINT BIT24
-#define SDIO_HISR_ATIMEND BIT25
-#define SDIO_HISR_ATIMEND_E BIT26
-#define SDIO_HISR_CTWEND BIT27
+#define SDIO_HISR_RX_REQUEST BIT(0)
+#define SDIO_HISR_AVAL BIT(1)
+#define SDIO_HISR_TXERR BIT(2)
+#define SDIO_HISR_RXERR BIT(3)
+#define SDIO_HISR_TXFOVW BIT(4)
+#define SDIO_HISR_RXFOVW BIT(5)
+#define SDIO_HISR_TXBCNOK BIT(6)
+#define SDIO_HISR_TXBCNERR BIT(7)
+#define SDIO_HISR_BCNERLY_INT BIT(16)
+#define SDIO_HISR_C2HCMD BIT(17)
+#define SDIO_HISR_CPWM1 BIT(18)
+#define SDIO_HISR_CPWM2 BIT(19)
+#define SDIO_HISR_HSISR_IND BIT(20)
+#define SDIO_HISR_GTINT3_IND BIT(21)
+#define SDIO_HISR_GTINT4_IND BIT(22)
+#define SDIO_HISR_PSTIME BIT(23)
+#define SDIO_HISR_OCPINT BIT(24)
+#define SDIO_HISR_ATIMEND BIT(25)
+#define SDIO_HISR_ATIMEND_E BIT(26)
+#define SDIO_HISR_CTWEND BIT(27)
/* RTL8188E SDIO Specific */
-#define SDIO_HISR_MCU_ERR BIT28
-#define SDIO_HISR_TSF_BIT32_TOGGLE BIT29
+#define SDIO_HISR_MCU_ERR BIT(28)
+#define SDIO_HISR_TSF_BIT32_TOGGLE BIT(29)
#define MASK_SDIO_HISR_CLEAR \
(SDIO_HISR_TXERR | SDIO_HISR_RXERR | SDIO_HISR_TXFOVW |\
SDIO_HISR_PSTIMEOUT | SDIO_HISR_OCPINT)
/* SDIO HCI Suspend Control Register */
-#define HCI_RESUME_PWR_RDY BIT1
-#define HCI_SUS_CTRL BIT0
+#define HCI_RESUME_PWR_RDY BIT(1)
+#define HCI_SUS_CTRL BIT(0)
/* SDIO Tx FIFO related */
/* The number of Tx FIFO free page */
/* 2REG_MULTI_FUNC_CTRL(For RTL8723 Only) */
/* Enable GPIO[9] as WiFi HW PDn source */
-#define WL_HWPDN_EN BIT0
+#define WL_HWPDN_EN BIT(0)
/* WiFi HW PDn polarity control */
-#define WL_HWPDN_SL BIT1
+#define WL_HWPDN_SL BIT(1)
/* WiFi function enable */
-#define WL_FUNC_EN BIT2
+#define WL_FUNC_EN BIT(2)
/* Enable GPIO[9] as WiFi RF HW PDn source */
-#define WL_HWROF_EN BIT3
+#define WL_HWROF_EN BIT(3)
/* Enable GPIO[11] as BT HW PDn source */
-#define BT_HWPDN_EN BIT16
+#define BT_HWPDN_EN BIT(16)
/* BT HW PDn polarity control */
-#define BT_HWPDN_SL BIT17
+#define BT_HWPDN_SL BIT(17)
/* BT function enable */
-#define BT_FUNC_EN BIT18
+#define BT_FUNC_EN BIT(18)
/* Enable GPIO[11] as BT/GPS RF HW PDn source */
-#define BT_HWROF_EN BIT19
+#define BT_HWROF_EN BIT(19)
/* Enable GPIO[10] as GPS HW PDn source */
-#define GPS_HWPDN_EN BIT20
+#define GPS_HWPDN_EN BIT(20)
/* GPS HW PDn polarity control */
-#define GPS_HWPDN_SL BIT21
+#define GPS_HWPDN_SL BIT(21)
/* GPS function enable */
-#define GPS_FUNC_EN BIT22
+#define GPS_FUNC_EN BIT(22)
/* 3 REG_LIFECTRL_CTRL */
-#define HAL92C_EN_PKT_LIFE_TIME_BK BIT3
-#define HAL92C_EN_PKT_LIFE_TIME_BE BIT2
-#define HAL92C_EN_PKT_LIFE_TIME_VI BIT1
-#define HAL92C_EN_PKT_LIFE_TIME_VO BIT0
+#define HAL92C_EN_PKT_LIFE_TIME_BK BIT(3)
+#define HAL92C_EN_PKT_LIFE_TIME_BE BIT(2)
+#define HAL92C_EN_PKT_LIFE_TIME_VI BIT(1)
+#define HAL92C_EN_PKT_LIFE_TIME_VO BIT(0)
#define HAL92C_MSDU_LIFE_TIME_UNIT 128 /* in us */
#define POLLING_LLT_THRESHOLD 20
#define POLLING_READY_TIMEOUT_COUNT 1000
/* GPIO BIT */
-#define HAL_8192C_HW_GPIO_WPS_BIT BIT2
+#define HAL_8192C_HW_GPIO_WPS_BIT BIT(2)
/* 8192C EEPROM/EFUSE share register definition. */
Code Review / kvmfornfv.git / blobdiff