--- /dev/null
+/*
+ * Cadence SPI controller driver (master mode only)
+ *
+ * Copyright (C) 2008 - 2014 Xilinx, Inc.
+ *
+ * based on Blackfin On-Chip SPI Driver (spi_bfin5xx.c)
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+/* Name of this driver */
+#define CDNS_SPI_NAME "cdns-spi"
+
+/* Register offset definitions */
+#define CDNS_SPI_CR_OFFSET 0x00 /* Configuration Register, RW */
+#define CDNS_SPI_ISR_OFFSET 0x04 /* Interrupt Status Register, RO */
+#define CDNS_SPI_IER_OFFSET 0x08 /* Interrupt Enable Register, WO */
+#define CDNS_SPI_IDR_OFFSET 0x0c /* Interrupt Disable Register, WO */
+#define CDNS_SPI_IMR_OFFSET 0x10 /* Interrupt Enabled Mask Register, RO */
+#define CDNS_SPI_ER_OFFSET 0x14 /* Enable/Disable Register, RW */
+#define CDNS_SPI_DR_OFFSET 0x18 /* Delay Register, RW */
+#define CDNS_SPI_TXD_OFFSET 0x1C /* Data Transmit Register, WO */
+#define CDNS_SPI_RXD_OFFSET 0x20 /* Data Receive Register, RO */
+#define CDNS_SPI_SICR_OFFSET 0x24 /* Slave Idle Count Register, RW */
+#define CDNS_SPI_THLD_OFFSET 0x28 /* Transmit FIFO Watermark Register,RW */
+
+/*
+ * SPI Configuration Register bit Masks
+ *
+ * This register contains various control bits that affect the operation
+ * of the SPI controller
+ */
+#define CDNS_SPI_CR_MANSTRT_MASK 0x00010000 /* Manual TX Start */
+#define CDNS_SPI_CR_CPHA_MASK 0x00000004 /* Clock Phase Control */
+#define CDNS_SPI_CR_CPOL_MASK 0x00000002 /* Clock Polarity Control */
+#define CDNS_SPI_CR_SSCTRL_MASK 0x00003C00 /* Slave Select Mask */
+#define CDNS_SPI_CR_PERI_SEL_MASK 0x00000200 /* Peripheral Select Decode */
+#define CDNS_SPI_CR_BAUD_DIV_MASK 0x00000038 /* Baud Rate Divisor Mask */
+#define CDNS_SPI_CR_MSTREN_MASK 0x00000001 /* Master Enable Mask */
+#define CDNS_SPI_CR_MANSTRTEN_MASK 0x00008000 /* Manual TX Enable Mask */
+#define CDNS_SPI_CR_SSFORCE_MASK 0x00004000 /* Manual SS Enable Mask */
+#define CDNS_SPI_CR_BAUD_DIV_4_MASK 0x00000008 /* Default Baud Div Mask */
+#define CDNS_SPI_CR_DEFAULT_MASK (CDNS_SPI_CR_MSTREN_MASK | \
+ CDNS_SPI_CR_SSCTRL_MASK | \
+ CDNS_SPI_CR_SSFORCE_MASK | \
+ CDNS_SPI_CR_BAUD_DIV_4_MASK)
+
+/*
+ * SPI Configuration Register - Baud rate and slave select
+ *
+ * These are the values used in the calculation of baud rate divisor and
+ * setting the slave select.
+ */
+
+#define CDNS_SPI_BAUD_DIV_MAX 7 /* Baud rate divisor maximum */
+#define CDNS_SPI_BAUD_DIV_MIN 1 /* Baud rate divisor minimum */
+#define CDNS_SPI_BAUD_DIV_SHIFT 3 /* Baud rate divisor shift in CR */
+#define CDNS_SPI_SS_SHIFT 10 /* Slave Select field shift in CR */
+#define CDNS_SPI_SS0 0x1 /* Slave Select zero */
+
+/*
+ * SPI Interrupt Registers bit Masks
+ *
+ * All the four interrupt registers (Status/Mask/Enable/Disable) have the same
+ * bit definitions.
+ */
+#define CDNS_SPI_IXR_TXOW_MASK 0x00000004 /* SPI TX FIFO Overwater */
+#define CDNS_SPI_IXR_MODF_MASK 0x00000002 /* SPI Mode Fault */
+#define CDNS_SPI_IXR_RXNEMTY_MASK 0x00000010 /* SPI RX FIFO Not Empty */
+#define CDNS_SPI_IXR_DEFAULT_MASK (CDNS_SPI_IXR_TXOW_MASK | \
+ CDNS_SPI_IXR_MODF_MASK)
+#define CDNS_SPI_IXR_TXFULL_MASK 0x00000008 /* SPI TX Full */
+#define CDNS_SPI_IXR_ALL_MASK 0x0000007F /* SPI all interrupts */
+
+/*
+ * SPI Enable Register bit Masks
+ *
+ * This register is used to enable or disable the SPI controller
+ */
+#define CDNS_SPI_ER_ENABLE_MASK 0x00000001 /* SPI Enable Bit Mask */
+#define CDNS_SPI_ER_DISABLE_MASK 0x0 /* SPI Disable Bit Mask */
+
+/* SPI FIFO depth in bytes */
+#define CDNS_SPI_FIFO_DEPTH 128
+
+/* Default number of chip select lines */
+#define CDNS_SPI_DEFAULT_NUM_CS 4
+
+/**
+ * struct cdns_spi - This definition defines spi driver instance
+ * @regs: Virtual address of the SPI controller registers
+ * @ref_clk: Pointer to the peripheral clock
+ * @pclk: Pointer to the APB clock
+ * @speed_hz: Current SPI bus clock speed in Hz
+ * @txbuf: Pointer to the TX buffer
+ * @rxbuf: Pointer to the RX buffer
+ * @tx_bytes: Number of bytes left to transfer
+ * @rx_bytes: Number of bytes requested
+ * @dev_busy: Device busy flag
+ * @is_decoded_cs: Flag for decoder property set or not
+ */
+struct cdns_spi {
+ void __iomem *regs;
+ struct clk *ref_clk;
+ struct clk *pclk;
+ u32 speed_hz;
+ const u8 *txbuf;
+ u8 *rxbuf;
+ int tx_bytes;
+ int rx_bytes;
+ u8 dev_busy;
+ u32 is_decoded_cs;
+};
+
+/* Macros for the SPI controller read/write */
+static inline u32 cdns_spi_read(struct cdns_spi *xspi, u32 offset)
+{
+ return readl_relaxed(xspi->regs + offset);
+}
+
+static inline void cdns_spi_write(struct cdns_spi *xspi, u32 offset, u32 val)
+{
+ writel_relaxed(val, xspi->regs + offset);
+}
+
+/**
+ * cdns_spi_init_hw - Initialize the hardware and configure the SPI controller
+ * @xspi: Pointer to the cdns_spi structure
+ *
+ * On reset the SPI controller is configured to be in master mode, baud rate
+ * divisor is set to 4, threshold value for TX FIFO not full interrupt is set
+ * to 1 and size of the word to be transferred as 8 bit.
+ * This function initializes the SPI controller to disable and clear all the
+ * interrupts, enable manual slave select and manual start, deselect all the
+ * chip select lines, and enable the SPI controller.
+ */
+static void cdns_spi_init_hw(struct cdns_spi *xspi)
+{
+ u32 ctrl_reg = CDNS_SPI_CR_DEFAULT_MASK;
+
+ if (xspi->is_decoded_cs)
+ ctrl_reg |= CDNS_SPI_CR_PERI_SEL_MASK;
+
+ cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
+ CDNS_SPI_ER_DISABLE_MASK);
+ cdns_spi_write(xspi, CDNS_SPI_IDR_OFFSET,
+ CDNS_SPI_IXR_ALL_MASK);
+
+ /* Clear the RX FIFO */
+ while (cdns_spi_read(xspi, CDNS_SPI_ISR_OFFSET) &
+ CDNS_SPI_IXR_RXNEMTY_MASK)
+ cdns_spi_read(xspi, CDNS_SPI_RXD_OFFSET);
+
+ cdns_spi_write(xspi, CDNS_SPI_ISR_OFFSET,
+ CDNS_SPI_IXR_ALL_MASK);
+ cdns_spi_write(xspi, CDNS_SPI_CR_OFFSET, ctrl_reg);
+ cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
+ CDNS_SPI_ER_ENABLE_MASK);
+}
+
+/**
+ * cdns_spi_chipselect - Select or deselect the chip select line
+ * @spi: Pointer to the spi_device structure
+ * @is_on: Select(0) or deselect (1) the chip select line
+ */
+static void cdns_spi_chipselect(struct spi_device *spi, bool is_high)
+{
+ struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
+ u32 ctrl_reg;
+
+ ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR_OFFSET);
+
+ if (is_high) {
+ /* Deselect the slave */
+ ctrl_reg |= CDNS_SPI_CR_SSCTRL_MASK;
+ } else {
+ /* Select the slave */
+ ctrl_reg &= ~CDNS_SPI_CR_SSCTRL_MASK;
+ if (!(xspi->is_decoded_cs))
+ ctrl_reg |= ((~(CDNS_SPI_SS0 << spi->chip_select)) <<
+ CDNS_SPI_SS_SHIFT) &
+ CDNS_SPI_CR_SSCTRL_MASK;
+ else
+ ctrl_reg |= (spi->chip_select << CDNS_SPI_SS_SHIFT) &
+ CDNS_SPI_CR_SSCTRL_MASK;
+ }
+
+ cdns_spi_write(xspi, CDNS_SPI_CR_OFFSET, ctrl_reg);
+}
+
+/**
+ * cdns_spi_config_clock_mode - Sets clock polarity and phase
+ * @spi: Pointer to the spi_device structure
+ *
+ * Sets the requested clock polarity and phase.
+ */
+static void cdns_spi_config_clock_mode(struct spi_device *spi)
+{
+ struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
+ u32 ctrl_reg, new_ctrl_reg;
+
+ new_ctrl_reg = ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR_OFFSET);
+
+ /* Set the SPI clock phase and clock polarity */
+ new_ctrl_reg &= ~(CDNS_SPI_CR_CPHA_MASK | CDNS_SPI_CR_CPOL_MASK);
+ if (spi->mode & SPI_CPHA)
+ new_ctrl_reg |= CDNS_SPI_CR_CPHA_MASK;
+ if (spi->mode & SPI_CPOL)
+ new_ctrl_reg |= CDNS_SPI_CR_CPOL_MASK;
+
+ if (new_ctrl_reg != ctrl_reg) {
+ /*
+ * Just writing the CR register does not seem to apply the clock
+ * setting changes. This is problematic when changing the clock
+ * polarity as it will cause the SPI slave to see spurious clock
+ * transitions. To workaround the issue toggle the ER register.
+ */
+ cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
+ CDNS_SPI_ER_DISABLE_MASK);
+ cdns_spi_write(xspi, CDNS_SPI_CR_OFFSET, new_ctrl_reg);
+ cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
+ CDNS_SPI_ER_ENABLE_MASK);
+ }
+}
+
+/**
+ * cdns_spi_config_clock_freq - Sets clock frequency
+ * @spi: Pointer to the spi_device structure
+ * @transfer: Pointer to the spi_transfer structure which provides
+ * information about next transfer setup parameters
+ *
+ * Sets the requested clock frequency.
+ * Note: If the requested frequency is not an exact match with what can be
+ * obtained using the prescalar value the driver sets the clock frequency which
+ * is lower than the requested frequency (maximum lower) for the transfer. If
+ * the requested frequency is higher or lower than that is supported by the SPI
+ * controller the driver will set the highest or lowest frequency supported by
+ * controller.
+ */
+static void cdns_spi_config_clock_freq(struct spi_device *spi,
+ struct spi_transfer *transfer)
+{
+ struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
+ u32 ctrl_reg, baud_rate_val;
+ unsigned long frequency;
+
+ frequency = clk_get_rate(xspi->ref_clk);
+
+ ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR_OFFSET);
+
+ /* Set the clock frequency */
+ if (xspi->speed_hz != transfer->speed_hz) {
+ /* first valid value is 1 */
+ baud_rate_val = CDNS_SPI_BAUD_DIV_MIN;
+ while ((baud_rate_val < CDNS_SPI_BAUD_DIV_MAX) &&
+ (frequency / (2 << baud_rate_val)) > transfer->speed_hz)
+ baud_rate_val++;
+
+ ctrl_reg &= ~CDNS_SPI_CR_BAUD_DIV_MASK;
+ ctrl_reg |= baud_rate_val << CDNS_SPI_BAUD_DIV_SHIFT;
+
+ xspi->speed_hz = frequency / (2 << baud_rate_val);
+ }
+ cdns_spi_write(xspi, CDNS_SPI_CR_OFFSET, ctrl_reg);
+}
+
+/**
+ * cdns_spi_setup_transfer - Configure SPI controller for specified transfer
+ * @spi: Pointer to the spi_device structure
+ * @transfer: Pointer to the spi_transfer structure which provides
+ * information about next transfer setup parameters
+ *
+ * Sets the operational mode of SPI controller for the next SPI transfer and
+ * sets the requested clock frequency.
+ *
+ * Return: Always 0
+ */
+static int cdns_spi_setup_transfer(struct spi_device *spi,
+ struct spi_transfer *transfer)
+{
+ struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
+
+ cdns_spi_config_clock_freq(spi, transfer);
+
+ dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u clock speed\n",
+ __func__, spi->mode, spi->bits_per_word,
+ xspi->speed_hz);
+
+ return 0;
+}
+
+/**
+ * cdns_spi_fill_tx_fifo - Fills the TX FIFO with as many bytes as possible
+ * @xspi: Pointer to the cdns_spi structure
+ */
+static void cdns_spi_fill_tx_fifo(struct cdns_spi *xspi)
+{
+ unsigned long trans_cnt = 0;
+
+ while ((trans_cnt < CDNS_SPI_FIFO_DEPTH) &&
+ (xspi->tx_bytes > 0)) {
+ if (xspi->txbuf)
+ cdns_spi_write(xspi, CDNS_SPI_TXD_OFFSET,
+ *xspi->txbuf++);
+ else
+ cdns_spi_write(xspi, CDNS_SPI_TXD_OFFSET, 0);
+
+ xspi->tx_bytes--;
+ trans_cnt++;
+ }
+}
+
+/**
+ * cdns_spi_irq - Interrupt service routine of the SPI controller
+ * @irq: IRQ number
+ * @dev_id: Pointer to the xspi structure
+ *
+ * This function handles TX empty and Mode Fault interrupts only.
+ * On TX empty interrupt this function reads the received data from RX FIFO and
+ * fills the TX FIFO if there is any data remaining to be transferred.
+ * On Mode Fault interrupt this function indicates that transfer is completed,
+ * the SPI subsystem will identify the error as the remaining bytes to be
+ * transferred is non-zero.
+ *
+ * Return: IRQ_HANDLED when handled; IRQ_NONE otherwise.
+ */
+static irqreturn_t cdns_spi_irq(int irq, void *dev_id)
+{
+ struct spi_master *master = dev_id;
+ struct cdns_spi *xspi = spi_master_get_devdata(master);
+ u32 intr_status, status;
+
+ status = IRQ_NONE;
+ intr_status = cdns_spi_read(xspi, CDNS_SPI_ISR_OFFSET);
+ cdns_spi_write(xspi, CDNS_SPI_ISR_OFFSET, intr_status);
+
+ if (intr_status & CDNS_SPI_IXR_MODF_MASK) {
+ /* Indicate that transfer is completed, the SPI subsystem will
+ * identify the error as the remaining bytes to be
+ * transferred is non-zero
+ */
+ cdns_spi_write(xspi, CDNS_SPI_IDR_OFFSET,
+ CDNS_SPI_IXR_DEFAULT_MASK);
+ spi_finalize_current_transfer(master);
+ status = IRQ_HANDLED;
+ } else if (intr_status & CDNS_SPI_IXR_TXOW_MASK) {
+ unsigned long trans_cnt;
+
+ trans_cnt = xspi->rx_bytes - xspi->tx_bytes;
+
+ /* Read out the data from the RX FIFO */
+ while (trans_cnt) {
+ u8 data;
+
+ data = cdns_spi_read(xspi, CDNS_SPI_RXD_OFFSET);
+ if (xspi->rxbuf)
+ *xspi->rxbuf++ = data;
+
+ xspi->rx_bytes--;
+ trans_cnt--;
+ }
+
+ if (xspi->tx_bytes) {
+ /* There is more data to send */
+ cdns_spi_fill_tx_fifo(xspi);
+ } else {
+ /* Transfer is completed */
+ cdns_spi_write(xspi, CDNS_SPI_IDR_OFFSET,
+ CDNS_SPI_IXR_DEFAULT_MASK);
+ spi_finalize_current_transfer(master);
+ }
+ status = IRQ_HANDLED;
+ }
+
+ return status;
+}
+static int cdns_prepare_message(struct spi_master *master,
+ struct spi_message *msg)
+{
+ cdns_spi_config_clock_mode(msg->spi);
+ return 0;
+}
+
+/**
+ * cdns_transfer_one - Initiates the SPI transfer
+ * @master: Pointer to spi_master structure
+ * @spi: Pointer to the spi_device structure
+ * @transfer: Pointer to the spi_transfer structure which provides
+ * information about next transfer parameters
+ *
+ * This function fills the TX FIFO, starts the SPI transfer and
+ * returns a positive transfer count so that core will wait for completion.
+ *
+ * Return: Number of bytes transferred in the last transfer
+ */
+static int cdns_transfer_one(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *transfer)
+{
+ struct cdns_spi *xspi = spi_master_get_devdata(master);
+
+ xspi->txbuf = transfer->tx_buf;
+ xspi->rxbuf = transfer->rx_buf;
+ xspi->tx_bytes = transfer->len;
+ xspi->rx_bytes = transfer->len;
+
+ cdns_spi_setup_transfer(spi, transfer);
+
+ cdns_spi_fill_tx_fifo(xspi);
+
+ cdns_spi_write(xspi, CDNS_SPI_IER_OFFSET,
+ CDNS_SPI_IXR_DEFAULT_MASK);
+ return transfer->len;
+}
+
+/**
+ * cdns_prepare_transfer_hardware - Prepares hardware for transfer.
+ * @master: Pointer to the spi_master structure which provides
+ * information about the controller.
+ *
+ * This function enables SPI master controller.
+ *
+ * Return: 0 always
+ */
+static int cdns_prepare_transfer_hardware(struct spi_master *master)
+{
+ struct cdns_spi *xspi = spi_master_get_devdata(master);
+
+ cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
+ CDNS_SPI_ER_ENABLE_MASK);
+
+ return 0;
+}
+
+/**
+ * cdns_unprepare_transfer_hardware - Relaxes hardware after transfer
+ * @master: Pointer to the spi_master structure which provides
+ * information about the controller.
+ *
+ * This function disables the SPI master controller.
+ *
+ * Return: 0 always
+ */
+static int cdns_unprepare_transfer_hardware(struct spi_master *master)
+{
+ struct cdns_spi *xspi = spi_master_get_devdata(master);
+
+ cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
+ CDNS_SPI_ER_DISABLE_MASK);
+
+ return 0;
+}
+
+/**
+ * cdns_spi_probe - Probe method for the SPI driver
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This function initializes the driver data structures and the hardware.
+ *
+ * Return: 0 on success and error value on error
+ */
+static int cdns_spi_probe(struct platform_device *pdev)
+{
+ int ret = 0, irq;
+ struct spi_master *master;
+ struct cdns_spi *xspi;
+ struct resource *res;
+ u32 num_cs;
+
+ master = spi_alloc_master(&pdev->dev, sizeof(*xspi));
+ if (master == NULL)
+ return -ENOMEM;
+
+ xspi = spi_master_get_devdata(master);
+ master->dev.of_node = pdev->dev.of_node;
+ platform_set_drvdata(pdev, master);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ xspi->regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(xspi->regs)) {
+ ret = PTR_ERR(xspi->regs);
+ goto remove_master;
+ }
+
+ xspi->pclk = devm_clk_get(&pdev->dev, "pclk");
+ if (IS_ERR(xspi->pclk)) {
+ dev_err(&pdev->dev, "pclk clock not found.\n");
+ ret = PTR_ERR(xspi->pclk);
+ goto remove_master;
+ }
+
+ xspi->ref_clk = devm_clk_get(&pdev->dev, "ref_clk");
+ if (IS_ERR(xspi->ref_clk)) {
+ dev_err(&pdev->dev, "ref_clk clock not found.\n");
+ ret = PTR_ERR(xspi->ref_clk);
+ goto remove_master;
+ }
+
+ ret = clk_prepare_enable(xspi->pclk);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to enable APB clock.\n");
+ goto remove_master;
+ }
+
+ ret = clk_prepare_enable(xspi->ref_clk);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to enable device clock.\n");
+ goto clk_dis_apb;
+ }
+
+ ret = of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs);
+ if (ret < 0)
+ master->num_chipselect = CDNS_SPI_DEFAULT_NUM_CS;
+ else
+ master->num_chipselect = num_cs;
+
+ ret = of_property_read_u32(pdev->dev.of_node, "is-decoded-cs",
+ &xspi->is_decoded_cs);
+ if (ret < 0)
+ xspi->is_decoded_cs = 0;
+
+ /* SPI controller initializations */
+ cdns_spi_init_hw(xspi);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0) {
+ ret = -ENXIO;
+ dev_err(&pdev->dev, "irq number is invalid\n");
+ goto remove_master;
+ }
+
+ ret = devm_request_irq(&pdev->dev, irq, cdns_spi_irq,
+ 0, pdev->name, master);
+ if (ret != 0) {
+ ret = -ENXIO;
+ dev_err(&pdev->dev, "request_irq failed\n");
+ goto remove_master;
+ }
+
+ master->prepare_transfer_hardware = cdns_prepare_transfer_hardware;
+ master->prepare_message = cdns_prepare_message;
+ master->transfer_one = cdns_transfer_one;
+ master->unprepare_transfer_hardware = cdns_unprepare_transfer_hardware;
+ master->set_cs = cdns_spi_chipselect;
+ master->mode_bits = SPI_CPOL | SPI_CPHA;
+
+ /* Set to default valid value */
+ master->max_speed_hz = clk_get_rate(xspi->ref_clk) / 4;
+ xspi->speed_hz = master->max_speed_hz;
+
+ master->bits_per_word_mask = SPI_BPW_MASK(8);
+
+ ret = spi_register_master(master);
+ if (ret) {
+ dev_err(&pdev->dev, "spi_register_master failed\n");
+ goto clk_dis_all;
+ }
+
+ return ret;
+
+clk_dis_all:
+ clk_disable_unprepare(xspi->ref_clk);
+clk_dis_apb:
+ clk_disable_unprepare(xspi->pclk);
+remove_master:
+ spi_master_put(master);
+ return ret;
+}
+
+/**
+ * cdns_spi_remove - Remove method for the SPI driver
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This function is called if a device is physically removed from the system or
+ * if the driver module is being unloaded. It frees all resources allocated to
+ * the device.
+ *
+ * Return: 0 on success and error value on error
+ */
+static int cdns_spi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct cdns_spi *xspi = spi_master_get_devdata(master);
+
+ cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
+ CDNS_SPI_ER_DISABLE_MASK);
+
+ clk_disable_unprepare(xspi->ref_clk);
+ clk_disable_unprepare(xspi->pclk);
+
+ spi_unregister_master(master);
+
+ return 0;
+}
+
+/**
+ * cdns_spi_suspend - Suspend method for the SPI driver
+ * @dev: Address of the platform_device structure
+ *
+ * This function disables the SPI controller and
+ * changes the driver state to "suspend"
+ *
+ * Return: Always 0
+ */
+static int __maybe_unused cdns_spi_suspend(struct device *dev)
+{
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct cdns_spi *xspi = spi_master_get_devdata(master);
+
+ spi_master_suspend(master);
+
+ clk_disable_unprepare(xspi->ref_clk);
+
+ clk_disable_unprepare(xspi->pclk);
+
+ return 0;
+}
+
+/**
+ * cdns_spi_resume - Resume method for the SPI driver
+ * @dev: Address of the platform_device structure
+ *
+ * This function changes the driver state to "ready"
+ *
+ * Return: 0 on success and error value on error
+ */
+static int __maybe_unused cdns_spi_resume(struct device *dev)
+{
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct cdns_spi *xspi = spi_master_get_devdata(master);
+ int ret = 0;
+
+ ret = clk_prepare_enable(xspi->pclk);
+ if (ret) {
+ dev_err(dev, "Cannot enable APB clock.\n");
+ return ret;
+ }
+
+ ret = clk_prepare_enable(xspi->ref_clk);
+ if (ret) {
+ dev_err(dev, "Cannot enable device clock.\n");
+ clk_disable(xspi->pclk);
+ return ret;
+ }
+ spi_master_resume(master);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(cdns_spi_dev_pm_ops, cdns_spi_suspend,
+ cdns_spi_resume);
+
+static const struct of_device_id cdns_spi_of_match[] = {
+ { .compatible = "xlnx,zynq-spi-r1p6" },
+ { .compatible = "cdns,spi-r1p6" },
+ { /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, cdns_spi_of_match);
+
+/* cdns_spi_driver - This structure defines the SPI subsystem platform driver */
+static struct platform_driver cdns_spi_driver = {
+ .probe = cdns_spi_probe,
+ .remove = cdns_spi_remove,
+ .driver = {
+ .name = CDNS_SPI_NAME,
+ .of_match_table = cdns_spi_of_match,
+ .pm = &cdns_spi_dev_pm_ops,
+ },
+};
+
+module_platform_driver(cdns_spi_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("Cadence SPI driver");
+MODULE_LICENSE("GPL");
Code Review / kvmfornfv.git / blobdiff