--- /dev/null
+/*
+ * QLogic Fibre Channel HBA Driver
+ * Copyright (c) 2003-2014 QLogic Corporation
+ *
+ * See LICENSE.qla2xxx for copyright and licensing details.
+ */
+#ifndef __QLA_FW_H
+#define __QLA_FW_H
+
+#define MBS_CHECKSUM_ERROR 0x4010
+#define MBS_INVALID_PRODUCT_KEY 0x4020
+
+/*
+ * Firmware Options.
+ */
+#define FO1_ENABLE_PUREX BIT_10
+#define FO1_DISABLE_LED_CTRL BIT_6
+#define FO1_ENABLE_8016 BIT_0
+#define FO2_ENABLE_SEL_CLASS2 BIT_5
+#define FO3_NO_ABTS_ON_LINKDOWN BIT_14
+#define FO3_HOLD_STS_IOCB BIT_12
+
+/*
+ * Port Database structure definition for ISP 24xx.
+ */
+#define PDO_FORCE_ADISC BIT_1
+#define PDO_FORCE_PLOGI BIT_0
+
+
+#define PORT_DATABASE_24XX_SIZE 64
+struct port_database_24xx {
+ uint16_t flags;
+#define PDF_TASK_RETRY_ID BIT_14
+#define PDF_FC_TAPE BIT_7
+#define PDF_ACK0_CAPABLE BIT_6
+#define PDF_FCP2_CONF BIT_5
+#define PDF_CLASS_2 BIT_4
+#define PDF_HARD_ADDR BIT_1
+
+ uint8_t current_login_state;
+ uint8_t last_login_state;
+#define PDS_PLOGI_PENDING 0x03
+#define PDS_PLOGI_COMPLETE 0x04
+#define PDS_PRLI_PENDING 0x05
+#define PDS_PRLI_COMPLETE 0x06
+#define PDS_PORT_UNAVAILABLE 0x07
+#define PDS_PRLO_PENDING 0x09
+#define PDS_LOGO_PENDING 0x11
+#define PDS_PRLI2_PENDING 0x12
+
+ uint8_t hard_address[3];
+ uint8_t reserved_1;
+
+ uint8_t port_id[3];
+ uint8_t sequence_id;
+
+ uint16_t port_timer;
+
+ uint16_t nport_handle; /* N_PORT handle. */
+
+ uint16_t receive_data_size;
+ uint16_t reserved_2;
+
+ uint8_t prli_svc_param_word_0[2]; /* Big endian */
+ /* Bits 15-0 of word 0 */
+ uint8_t prli_svc_param_word_3[2]; /* Big endian */
+ /* Bits 15-0 of word 3 */
+
+ uint8_t port_name[WWN_SIZE];
+ uint8_t node_name[WWN_SIZE];
+
+ uint8_t reserved_3[24];
+};
+
+struct vp_database_24xx {
+ uint16_t vp_status;
+ uint8_t options;
+ uint8_t id;
+ uint8_t port_name[WWN_SIZE];
+ uint8_t node_name[WWN_SIZE];
+ uint16_t port_id_low;
+ uint16_t port_id_high;
+};
+
+struct nvram_24xx {
+ /* NVRAM header. */
+ uint8_t id[4];
+ uint16_t nvram_version;
+ uint16_t reserved_0;
+
+ /* Firmware Initialization Control Block. */
+ uint16_t version;
+ uint16_t reserved_1;
+ __le16 frame_payload_size;
+ uint16_t execution_throttle;
+ uint16_t exchange_count;
+ uint16_t hard_address;
+
+ uint8_t port_name[WWN_SIZE];
+ uint8_t node_name[WWN_SIZE];
+
+ uint16_t login_retry_count;
+ uint16_t link_down_on_nos;
+ uint16_t interrupt_delay_timer;
+ uint16_t login_timeout;
+
+ uint32_t firmware_options_1;
+ uint32_t firmware_options_2;
+ uint32_t firmware_options_3;
+
+ /* Offset 56. */
+
+ /*
+ * BIT 0 = Control Enable
+ * BIT 1-15 =
+ *
+ * BIT 0-7 = Reserved
+ * BIT 8-10 = Output Swing 1G
+ * BIT 11-13 = Output Emphasis 1G
+ * BIT 14-15 = Reserved
+ *
+ * BIT 0-7 = Reserved
+ * BIT 8-10 = Output Swing 2G
+ * BIT 11-13 = Output Emphasis 2G
+ * BIT 14-15 = Reserved
+ *
+ * BIT 0-7 = Reserved
+ * BIT 8-10 = Output Swing 4G
+ * BIT 11-13 = Output Emphasis 4G
+ * BIT 14-15 = Reserved
+ */
+ uint16_t seriallink_options[4];
+
+ uint16_t reserved_2[16];
+
+ /* Offset 96. */
+ uint16_t reserved_3[16];
+
+ /* PCIe table entries. */
+ uint16_t reserved_4[16];
+
+ /* Offset 160. */
+ uint16_t reserved_5[16];
+
+ /* Offset 192. */
+ uint16_t reserved_6[16];
+
+ /* Offset 224. */
+ uint16_t reserved_7[16];
+
+ /*
+ * BIT 0 = Enable spinup delay
+ * BIT 1 = Disable BIOS
+ * BIT 2 = Enable Memory Map BIOS
+ * BIT 3 = Enable Selectable Boot
+ * BIT 4 = Disable RISC code load
+ * BIT 5 = Disable Serdes
+ * BIT 6 =
+ * BIT 7 =
+ *
+ * BIT 8 =
+ * BIT 9 =
+ * BIT 10 = Enable lip full login
+ * BIT 11 = Enable target reset
+ * BIT 12 =
+ * BIT 13 =
+ * BIT 14 =
+ * BIT 15 = Enable alternate WWN
+ *
+ * BIT 16-31 =
+ */
+ uint32_t host_p;
+
+ uint8_t alternate_port_name[WWN_SIZE];
+ uint8_t alternate_node_name[WWN_SIZE];
+
+ uint8_t boot_port_name[WWN_SIZE];
+ uint16_t boot_lun_number;
+ uint16_t reserved_8;
+
+ uint8_t alt1_boot_port_name[WWN_SIZE];
+ uint16_t alt1_boot_lun_number;
+ uint16_t reserved_9;
+
+ uint8_t alt2_boot_port_name[WWN_SIZE];
+ uint16_t alt2_boot_lun_number;
+ uint16_t reserved_10;
+
+ uint8_t alt3_boot_port_name[WWN_SIZE];
+ uint16_t alt3_boot_lun_number;
+ uint16_t reserved_11;
+
+ /*
+ * BIT 0 = Selective Login
+ * BIT 1 = Alt-Boot Enable
+ * BIT 2 = Reserved
+ * BIT 3 = Boot Order List
+ * BIT 4 = Reserved
+ * BIT 5 = Selective LUN
+ * BIT 6 = Reserved
+ * BIT 7-31 =
+ */
+ uint32_t efi_parameters;
+
+ uint8_t reset_delay;
+ uint8_t reserved_12;
+ uint16_t reserved_13;
+
+ uint16_t boot_id_number;
+ uint16_t reserved_14;
+
+ uint16_t max_luns_per_target;
+ uint16_t reserved_15;
+
+ uint16_t port_down_retry_count;
+ uint16_t link_down_timeout;
+
+ /* FCode parameters. */
+ uint16_t fcode_parameter;
+
+ uint16_t reserved_16[3];
+
+ /* Offset 352. */
+ uint8_t prev_drv_ver_major;
+ uint8_t prev_drv_ver_submajob;
+ uint8_t prev_drv_ver_minor;
+ uint8_t prev_drv_ver_subminor;
+
+ uint16_t prev_bios_ver_major;
+ uint16_t prev_bios_ver_minor;
+
+ uint16_t prev_efi_ver_major;
+ uint16_t prev_efi_ver_minor;
+
+ uint16_t prev_fw_ver_major;
+ uint8_t prev_fw_ver_minor;
+ uint8_t prev_fw_ver_subminor;
+
+ uint16_t reserved_17[8];
+
+ /* Offset 384. */
+ uint16_t reserved_18[16];
+
+ /* Offset 416. */
+ uint16_t reserved_19[16];
+
+ /* Offset 448. */
+ uint16_t reserved_20[16];
+
+ /* Offset 480. */
+ uint8_t model_name[16];
+
+ uint16_t reserved_21[2];
+
+ /* Offset 500. */
+ /* HW Parameter Block. */
+ uint16_t pcie_table_sig;
+ uint16_t pcie_table_offset;
+
+ uint16_t subsystem_vendor_id;
+ uint16_t subsystem_device_id;
+
+ uint32_t checksum;
+};
+
+/*
+ * ISP Initialization Control Block.
+ * Little endian except where noted.
+ */
+#define ICB_VERSION 1
+struct init_cb_24xx {
+ uint16_t version;
+ uint16_t reserved_1;
+
+ uint16_t frame_payload_size;
+ uint16_t execution_throttle;
+ uint16_t exchange_count;
+
+ uint16_t hard_address;
+
+ uint8_t port_name[WWN_SIZE]; /* Big endian. */
+ uint8_t node_name[WWN_SIZE]; /* Big endian. */
+
+ uint16_t response_q_inpointer;
+ uint16_t request_q_outpointer;
+
+ uint16_t login_retry_count;
+
+ uint16_t prio_request_q_outpointer;
+
+ uint16_t response_q_length;
+ uint16_t request_q_length;
+
+ uint16_t link_down_on_nos; /* Milliseconds. */
+
+ uint16_t prio_request_q_length;
+
+ uint32_t request_q_address[2];
+ uint32_t response_q_address[2];
+ uint32_t prio_request_q_address[2];
+
+ uint16_t msix;
+ uint16_t msix_atio;
+ uint8_t reserved_2[4];
+
+ uint16_t atio_q_inpointer;
+ uint16_t atio_q_length;
+ uint32_t atio_q_address[2];
+
+ uint16_t interrupt_delay_timer; /* 100us increments. */
+ uint16_t login_timeout;
+
+ /*
+ * BIT 0 = Enable Hard Loop Id
+ * BIT 1 = Enable Fairness
+ * BIT 2 = Enable Full-Duplex
+ * BIT 3 = Reserved
+ * BIT 4 = Enable Target Mode
+ * BIT 5 = Disable Initiator Mode
+ * BIT 6 = Acquire FA-WWN
+ * BIT 7 = Enable D-port Diagnostics
+ *
+ * BIT 8 = Reserved
+ * BIT 9 = Non Participating LIP
+ * BIT 10 = Descending Loop ID Search
+ * BIT 11 = Acquire Loop ID in LIPA
+ * BIT 12 = Reserved
+ * BIT 13 = Full Login after LIP
+ * BIT 14 = Node Name Option
+ * BIT 15-31 = Reserved
+ */
+ uint32_t firmware_options_1;
+
+ /*
+ * BIT 0 = Operation Mode bit 0
+ * BIT 1 = Operation Mode bit 1
+ * BIT 2 = Operation Mode bit 2
+ * BIT 3 = Operation Mode bit 3
+ * BIT 4 = Connection Options bit 0
+ * BIT 5 = Connection Options bit 1
+ * BIT 6 = Connection Options bit 2
+ * BIT 7 = Enable Non part on LIHA failure
+ *
+ * BIT 8 = Enable Class 2
+ * BIT 9 = Enable ACK0
+ * BIT 10 = Reserved
+ * BIT 11 = Enable FC-SP Security
+ * BIT 12 = FC Tape Enable
+ * BIT 13 = Reserved
+ * BIT 14 = Enable Target PRLI Control
+ * BIT 15-31 = Reserved
+ */
+ uint32_t firmware_options_2;
+
+ /*
+ * BIT 0 = Reserved
+ * BIT 1 = Soft ID only
+ * BIT 2 = Reserved
+ * BIT 3 = Reserved
+ * BIT 4 = FCP RSP Payload bit 0
+ * BIT 5 = FCP RSP Payload bit 1
+ * BIT 6 = Enable Receive Out-of-Order data frame handling
+ * BIT 7 = Disable Automatic PLOGI on Local Loop
+ *
+ * BIT 8 = Reserved
+ * BIT 9 = Enable Out-of-Order FCP_XFER_RDY relative offset handling
+ * BIT 10 = Reserved
+ * BIT 11 = Reserved
+ * BIT 12 = Reserved
+ * BIT 13 = Data Rate bit 0
+ * BIT 14 = Data Rate bit 1
+ * BIT 15 = Data Rate bit 2
+ * BIT 16 = Enable 75 ohm Termination Select
+ * BIT 17-28 = Reserved
+ * BIT 29 = Enable response queue 0 in index shadowing
+ * BIT 30 = Enable request queue 0 out index shadowing
+ * BIT 31 = Reserved
+ */
+ uint32_t firmware_options_3;
+ uint16_t qos;
+ uint16_t rid;
+ uint8_t reserved_3[20];
+};
+
+/*
+ * ISP queue - command entry structure definition.
+ */
+#define COMMAND_BIDIRECTIONAL 0x75
+struct cmd_bidir {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined */
+ uint8_t entry_status; /* Entry status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t nport_handle; /* N_PORT hanlde. */
+
+ uint16_t timeout; /* Commnad timeout. */
+
+ uint16_t wr_dseg_count; /* Write Data segment count. */
+ uint16_t rd_dseg_count; /* Read Data segment count. */
+
+ struct scsi_lun lun; /* FCP LUN (BE). */
+
+ uint16_t control_flags; /* Control flags. */
+#define BD_WRAP_BACK BIT_3
+#define BD_READ_DATA BIT_1
+#define BD_WRITE_DATA BIT_0
+
+ uint16_t fcp_cmnd_dseg_len; /* Data segment length. */
+ uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */
+
+ uint16_t reserved[2]; /* Reserved */
+
+ uint32_t rd_byte_count; /* Total Byte count Read. */
+ uint32_t wr_byte_count; /* Total Byte count write. */
+
+ uint8_t port_id[3]; /* PortID of destination port.*/
+ uint8_t vp_index;
+
+ uint32_t fcp_data_dseg_address[2]; /* Data segment address. */
+ uint16_t fcp_data_dseg_len; /* Data segment length. */
+};
+
+#define COMMAND_TYPE_6 0x48 /* Command Type 6 entry */
+struct cmd_type_6 {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t nport_handle; /* N_PORT handle. */
+ uint16_t timeout; /* Command timeout. */
+
+ uint16_t dseg_count; /* Data segment count. */
+
+ uint16_t fcp_rsp_dsd_len; /* FCP_RSP DSD length. */
+
+ struct scsi_lun lun; /* FCP LUN (BE). */
+
+ uint16_t control_flags; /* Control flags. */
+#define CF_DIF_SEG_DESCR_ENABLE BIT_3
+#define CF_DATA_SEG_DESCR_ENABLE BIT_2
+#define CF_READ_DATA BIT_1
+#define CF_WRITE_DATA BIT_0
+
+ uint16_t fcp_cmnd_dseg_len; /* Data segment length. */
+ uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */
+
+ uint32_t fcp_rsp_dseg_address[2]; /* Data segment address. */
+
+ uint32_t byte_count; /* Total byte count. */
+
+ uint8_t port_id[3]; /* PortID of destination port. */
+ uint8_t vp_index;
+
+ uint32_t fcp_data_dseg_address[2]; /* Data segment address. */
+ uint32_t fcp_data_dseg_len; /* Data segment length. */
+};
+
+#define COMMAND_TYPE_7 0x18 /* Command Type 7 entry */
+struct cmd_type_7 {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t nport_handle; /* N_PORT handle. */
+ uint16_t timeout; /* Command timeout. */
+#define FW_MAX_TIMEOUT 0x1999
+
+ uint16_t dseg_count; /* Data segment count. */
+ uint16_t reserved_1;
+
+ struct scsi_lun lun; /* FCP LUN (BE). */
+
+ uint16_t task_mgmt_flags; /* Task management flags. */
+#define TMF_CLEAR_ACA BIT_14
+#define TMF_TARGET_RESET BIT_13
+#define TMF_LUN_RESET BIT_12
+#define TMF_CLEAR_TASK_SET BIT_10
+#define TMF_ABORT_TASK_SET BIT_9
+#define TMF_DSD_LIST_ENABLE BIT_2
+#define TMF_READ_DATA BIT_1
+#define TMF_WRITE_DATA BIT_0
+
+ uint8_t task;
+#define TSK_SIMPLE 0
+#define TSK_HEAD_OF_QUEUE 1
+#define TSK_ORDERED 2
+#define TSK_ACA 4
+#define TSK_UNTAGGED 5
+
+ uint8_t crn;
+
+ uint8_t fcp_cdb[MAX_CMDSZ]; /* SCSI command words. */
+ uint32_t byte_count; /* Total byte count. */
+
+ uint8_t port_id[3]; /* PortID of destination port. */
+ uint8_t vp_index;
+
+ uint32_t dseg_0_address[2]; /* Data segment 0 address. */
+ uint32_t dseg_0_len; /* Data segment 0 length. */
+};
+
+#define COMMAND_TYPE_CRC_2 0x6A /* Command Type CRC_2 (Type 6)
+ * (T10-DIF) */
+struct cmd_type_crc_2 {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t nport_handle; /* N_PORT handle. */
+ uint16_t timeout; /* Command timeout. */
+
+ uint16_t dseg_count; /* Data segment count. */
+
+ uint16_t fcp_rsp_dseg_len; /* FCP_RSP DSD length. */
+
+ struct scsi_lun lun; /* FCP LUN (BE). */
+
+ uint16_t control_flags; /* Control flags. */
+
+ uint16_t fcp_cmnd_dseg_len; /* Data segment length. */
+ uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */
+
+ uint32_t fcp_rsp_dseg_address[2]; /* Data segment address. */
+
+ uint32_t byte_count; /* Total byte count. */
+
+ uint8_t port_id[3]; /* PortID of destination port. */
+ uint8_t vp_index;
+
+ uint32_t crc_context_address[2]; /* Data segment address. */
+ uint16_t crc_context_len; /* Data segment length. */
+ uint16_t reserved_1; /* MUST be set to 0. */
+};
+
+
+/*
+ * ISP queue - status entry structure definition.
+ */
+#define STATUS_TYPE 0x03 /* Status entry. */
+struct sts_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t comp_status; /* Completion status. */
+ uint16_t ox_id; /* OX_ID used by the firmware. */
+
+ uint32_t residual_len; /* FW calc residual transfer length. */
+
+ uint16_t reserved_1;
+ uint16_t state_flags; /* State flags. */
+#define SF_TRANSFERRED_DATA BIT_11
+#define SF_FCP_RSP_DMA BIT_0
+
+ uint16_t retry_delay;
+ uint16_t scsi_status; /* SCSI status. */
+#define SS_CONFIRMATION_REQ BIT_12
+
+ uint32_t rsp_residual_count; /* FCP RSP residual count. */
+
+ uint32_t sense_len; /* FCP SENSE length. */
+ uint32_t rsp_data_len; /* FCP response data length. */
+ uint8_t data[28]; /* FCP response/sense information. */
+ /*
+ * If DIF Error is set in comp_status, these additional fields are
+ * defined:
+ *
+ * !!! NOTE: Firmware sends expected/actual DIF data in big endian
+ * format; but all of the "data" field gets swab32-d in the beginning
+ * of qla2x00_status_entry().
+ *
+ * &data[10] : uint8_t report_runt_bg[2]; - computed guard
+ * &data[12] : uint8_t actual_dif[8]; - DIF Data received
+ * &data[20] : uint8_t expected_dif[8]; - DIF Data computed
+ */
+};
+
+
+/*
+ * Status entry completion status
+ */
+#define CS_DATA_REASSEMBLY_ERROR 0x11 /* Data Reassembly Error.. */
+#define CS_ABTS_BY_TARGET 0x13 /* Target send ABTS to abort IOCB. */
+#define CS_FW_RESOURCE 0x2C /* Firmware Resource Unavailable. */
+#define CS_TASK_MGMT_OVERRUN 0x30 /* Task management overrun (8+). */
+#define CS_ABORT_BY_TARGET 0x47 /* Abort By Target. */
+
+/*
+ * ISP queue - marker entry structure definition.
+ */
+#define MARKER_TYPE 0x04 /* Marker entry. */
+struct mrk_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t handle_count; /* Handle count. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t nport_handle; /* N_PORT handle. */
+
+ uint8_t modifier; /* Modifier (7-0). */
+#define MK_SYNC_ID_LUN 0 /* Synchronize ID/LUN */
+#define MK_SYNC_ID 1 /* Synchronize ID */
+#define MK_SYNC_ALL 2 /* Synchronize all ID/LUN */
+ uint8_t reserved_1;
+
+ uint8_t reserved_2;
+ uint8_t vp_index;
+
+ uint16_t reserved_3;
+
+ uint8_t lun[8]; /* FCP LUN (BE). */
+ uint8_t reserved_4[40];
+};
+
+/*
+ * ISP queue - CT Pass-Through entry structure definition.
+ */
+#define CT_IOCB_TYPE 0x29 /* CT Pass-Through IOCB entry */
+struct ct_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System Defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t comp_status; /* Completion status. */
+
+ uint16_t nport_handle; /* N_PORT handle. */
+
+ uint16_t cmd_dsd_count;
+
+ uint8_t vp_index;
+ uint8_t reserved_1;
+
+ uint16_t timeout; /* Command timeout. */
+ uint16_t reserved_2;
+
+ uint16_t rsp_dsd_count;
+
+ uint8_t reserved_3[10];
+
+ uint32_t rsp_byte_count;
+ uint32_t cmd_byte_count;
+
+ uint32_t dseg_0_address[2]; /* Data segment 0 address. */
+ uint32_t dseg_0_len; /* Data segment 0 length. */
+ uint32_t dseg_1_address[2]; /* Data segment 1 address. */
+ uint32_t dseg_1_len; /* Data segment 1 length. */
+};
+
+/*
+ * ISP queue - ELS Pass-Through entry structure definition.
+ */
+#define ELS_IOCB_TYPE 0x53 /* ELS Pass-Through IOCB entry */
+struct els_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System Defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t reserved_1;
+
+ uint16_t nport_handle; /* N_PORT handle. */
+
+ uint16_t tx_dsd_count;
+
+ uint8_t vp_index;
+ uint8_t sof_type;
+#define EST_SOFI3 (1 << 4)
+#define EST_SOFI2 (3 << 4)
+
+ uint32_t rx_xchg_address; /* Receive exchange address. */
+ uint16_t rx_dsd_count;
+
+ uint8_t opcode;
+ uint8_t reserved_2;
+
+ uint8_t port_id[3];
+ uint8_t reserved_3;
+
+ uint16_t reserved_4;
+
+ uint16_t control_flags; /* Control flags. */
+#define ECF_PAYLOAD_DESCR_MASK (BIT_15|BIT_14|BIT_13)
+#define EPD_ELS_COMMAND (0 << 13)
+#define EPD_ELS_ACC (1 << 13)
+#define EPD_ELS_RJT (2 << 13)
+#define EPD_RX_XCHG (3 << 13)
+#define ECF_CLR_PASSTHRU_PEND BIT_12
+#define ECF_INCL_FRAME_HDR BIT_11
+
+ uint32_t rx_byte_count;
+ uint32_t tx_byte_count;
+
+ uint32_t tx_address[2]; /* Data segment 0 address. */
+ uint32_t tx_len; /* Data segment 0 length. */
+ uint32_t rx_address[2]; /* Data segment 1 address. */
+ uint32_t rx_len; /* Data segment 1 length. */
+};
+
+struct els_sts_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System Defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t comp_status;
+
+ uint16_t nport_handle; /* N_PORT handle. */
+
+ uint16_t reserved_1;
+
+ uint8_t vp_index;
+ uint8_t sof_type;
+
+ uint32_t rx_xchg_address; /* Receive exchange address. */
+ uint16_t reserved_2;
+
+ uint8_t opcode;
+ uint8_t reserved_3;
+
+ uint8_t port_id[3];
+ uint8_t reserved_4;
+
+ uint16_t reserved_5;
+
+ uint16_t control_flags; /* Control flags. */
+ uint32_t total_byte_count;
+ uint32_t error_subcode_1;
+ uint32_t error_subcode_2;
+};
+/*
+ * ISP queue - Mailbox Command entry structure definition.
+ */
+#define MBX_IOCB_TYPE 0x39
+struct mbx_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t handle_count; /* Handle count. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t mbx[28];
+};
+
+
+#define LOGINOUT_PORT_IOCB_TYPE 0x52 /* Login/Logout Port entry. */
+struct logio_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t comp_status; /* Completion status. */
+#define CS_LOGIO_ERROR 0x31 /* Login/Logout IOCB error. */
+
+ uint16_t nport_handle; /* N_PORT handle. */
+
+ uint16_t control_flags; /* Control flags. */
+ /* Modifiers. */
+#define LCF_INCLUDE_SNS BIT_10 /* Include SNS (FFFFFC) during LOGO. */
+#define LCF_FCP2_OVERRIDE BIT_9 /* Set/Reset word 3 of PRLI. */
+#define LCF_CLASS_2 BIT_8 /* Enable class 2 during PLOGI. */
+#define LCF_FREE_NPORT BIT_7 /* Release NPORT handle after LOGO. */
+#define LCF_EXPL_LOGO BIT_6 /* Perform an explicit LOGO. */
+#define LCF_SKIP_PRLI BIT_5 /* Skip PRLI after PLOGI. */
+#define LCF_IMPL_LOGO_ALL BIT_5 /* Implicit LOGO to all ports. */
+#define LCF_COND_PLOGI BIT_4 /* PLOGI only if not logged-in. */
+#define LCF_IMPL_LOGO BIT_4 /* Perform an implicit LOGO. */
+#define LCF_IMPL_PRLO BIT_4 /* Perform an implicit PRLO. */
+ /* Commands. */
+#define LCF_COMMAND_PLOGI 0x00 /* PLOGI. */
+#define LCF_COMMAND_PRLI 0x01 /* PRLI. */
+#define LCF_COMMAND_PDISC 0x02 /* PDISC. */
+#define LCF_COMMAND_ADISC 0x03 /* ADISC. */
+#define LCF_COMMAND_LOGO 0x08 /* LOGO. */
+#define LCF_COMMAND_PRLO 0x09 /* PRLO. */
+#define LCF_COMMAND_TPRLO 0x0A /* TPRLO. */
+
+ uint8_t vp_index;
+ uint8_t reserved_1;
+
+ uint8_t port_id[3]; /* PortID of destination port. */
+
+ uint8_t rsp_size; /* Response size in 32bit words. */
+
+ uint32_t io_parameter[11]; /* General I/O parameters. */
+#define LSC_SCODE_NOLINK 0x01
+#define LSC_SCODE_NOIOCB 0x02
+#define LSC_SCODE_NOXCB 0x03
+#define LSC_SCODE_CMD_FAILED 0x04
+#define LSC_SCODE_NOFABRIC 0x05
+#define LSC_SCODE_FW_NOT_READY 0x07
+#define LSC_SCODE_NOT_LOGGED_IN 0x09
+#define LSC_SCODE_NOPCB 0x0A
+
+#define LSC_SCODE_ELS_REJECT 0x18
+#define LSC_SCODE_CMD_PARAM_ERR 0x19
+#define LSC_SCODE_PORTID_USED 0x1A
+#define LSC_SCODE_NPORT_USED 0x1B
+#define LSC_SCODE_NONPORT 0x1C
+#define LSC_SCODE_LOGGED_IN 0x1D
+#define LSC_SCODE_NOFLOGI_ACC 0x1F
+};
+
+#define TSK_MGMT_IOCB_TYPE 0x14
+struct tsk_mgmt_entry {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t handle_count; /* Handle count. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t nport_handle; /* N_PORT handle. */
+
+ uint16_t reserved_1;
+
+ uint16_t delay; /* Activity delay in seconds. */
+
+ uint16_t timeout; /* Command timeout. */
+
+ struct scsi_lun lun; /* FCP LUN (BE). */
+
+ uint32_t control_flags; /* Control Flags. */
+#define TCF_NOTMCMD_TO_TARGET BIT_31
+#define TCF_LUN_RESET BIT_4
+#define TCF_ABORT_TASK_SET BIT_3
+#define TCF_CLEAR_TASK_SET BIT_2
+#define TCF_TARGET_RESET BIT_1
+#define TCF_CLEAR_ACA BIT_0
+
+ uint8_t reserved_2[20];
+
+ uint8_t port_id[3]; /* PortID of destination port. */
+ uint8_t vp_index;
+
+ uint8_t reserved_3[12];
+};
+
+#define ABORT_IOCB_TYPE 0x33
+struct abort_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t handle_count; /* Handle count. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t nport_handle; /* N_PORT handle. */
+ /* or Completion status. */
+
+ uint16_t options; /* Options. */
+#define AOF_NO_ABTS BIT_0 /* Do not send any ABTS. */
+
+ uint32_t handle_to_abort; /* System handle to abort. */
+
+ uint16_t req_que_no;
+ uint8_t reserved_1[30];
+
+ uint8_t port_id[3]; /* PortID of destination port. */
+ uint8_t vp_index;
+
+ uint8_t reserved_2[12];
+};
+
+/*
+ * ISP I/O Register Set structure definitions.
+ */
+struct device_reg_24xx {
+ uint32_t flash_addr; /* Flash/NVRAM BIOS address. */
+#define FARX_DATA_FLAG BIT_31
+#define FARX_ACCESS_FLASH_CONF 0x7FFD0000
+#define FARX_ACCESS_FLASH_DATA 0x7FF00000
+#define FARX_ACCESS_NVRAM_CONF 0x7FFF0000
+#define FARX_ACCESS_NVRAM_DATA 0x7FFE0000
+
+#define FA_NVRAM_FUNC0_ADDR 0x80
+#define FA_NVRAM_FUNC1_ADDR 0x180
+
+#define FA_NVRAM_VPD_SIZE 0x200
+#define FA_NVRAM_VPD0_ADDR 0x00
+#define FA_NVRAM_VPD1_ADDR 0x100
+
+#define FA_BOOT_CODE_ADDR 0x00000
+ /*
+ * RISC code begins at offset 512KB
+ * within flash. Consisting of two
+ * contiguous RISC code segments.
+ */
+#define FA_RISC_CODE_ADDR 0x20000
+#define FA_RISC_CODE_SEGMENTS 2
+
+#define FA_FLASH_DESCR_ADDR_24 0x11000
+#define FA_FLASH_LAYOUT_ADDR_24 0x11400
+#define FA_NPIV_CONF0_ADDR_24 0x16000
+#define FA_NPIV_CONF1_ADDR_24 0x17000
+
+#define FA_FW_AREA_ADDR 0x40000
+#define FA_VPD_NVRAM_ADDR 0x48000
+#define FA_FEATURE_ADDR 0x4C000
+#define FA_FLASH_DESCR_ADDR 0x50000
+#define FA_FLASH_LAYOUT_ADDR 0x50400
+#define FA_HW_EVENT0_ADDR 0x54000
+#define FA_HW_EVENT1_ADDR 0x54400
+#define FA_HW_EVENT_SIZE 0x200
+#define FA_HW_EVENT_ENTRY_SIZE 4
+#define FA_NPIV_CONF0_ADDR 0x5C000
+#define FA_NPIV_CONF1_ADDR 0x5D000
+#define FA_FCP_PRIO0_ADDR 0x10000
+#define FA_FCP_PRIO1_ADDR 0x12000
+
+/*
+ * Flash Error Log Event Codes.
+ */
+#define HW_EVENT_RESET_ERR 0xF00B
+#define HW_EVENT_ISP_ERR 0xF020
+#define HW_EVENT_PARITY_ERR 0xF022
+#define HW_EVENT_NVRAM_CHKSUM_ERR 0xF023
+#define HW_EVENT_FLASH_FW_ERR 0xF024
+
+ uint32_t flash_data; /* Flash/NVRAM BIOS data. */
+
+ uint32_t ctrl_status; /* Control/Status. */
+#define CSRX_FLASH_ACCESS_ERROR BIT_18 /* Flash/NVRAM Access Error. */
+#define CSRX_DMA_ACTIVE BIT_17 /* DMA Active status. */
+#define CSRX_DMA_SHUTDOWN BIT_16 /* DMA Shutdown control status. */
+#define CSRX_FUNCTION BIT_15 /* Function number. */
+ /* PCI-X Bus Mode. */
+#define CSRX_PCIX_BUS_MODE_MASK (BIT_11|BIT_10|BIT_9|BIT_8)
+#define PBM_PCI_33MHZ (0 << 8)
+#define PBM_PCIX_M1_66MHZ (1 << 8)
+#define PBM_PCIX_M1_100MHZ (2 << 8)
+#define PBM_PCIX_M1_133MHZ (3 << 8)
+#define PBM_PCIX_M2_66MHZ (5 << 8)
+#define PBM_PCIX_M2_100MHZ (6 << 8)
+#define PBM_PCIX_M2_133MHZ (7 << 8)
+#define PBM_PCI_66MHZ (8 << 8)
+ /* Max Write Burst byte count. */
+#define CSRX_MAX_WRT_BURST_MASK (BIT_5|BIT_4)
+#define MWB_512_BYTES (0 << 4)
+#define MWB_1024_BYTES (1 << 4)
+#define MWB_2048_BYTES (2 << 4)
+#define MWB_4096_BYTES (3 << 4)
+
+#define CSRX_64BIT_SLOT BIT_2 /* PCI 64-Bit Bus Slot. */
+#define CSRX_FLASH_ENABLE BIT_1 /* Flash BIOS Read/Write enable. */
+#define CSRX_ISP_SOFT_RESET BIT_0 /* ISP soft reset. */
+
+ uint32_t ictrl; /* Interrupt control. */
+#define ICRX_EN_RISC_INT BIT_3 /* Enable RISC interrupts on PCI. */
+
+ uint32_t istatus; /* Interrupt status. */
+#define ISRX_RISC_INT BIT_3 /* RISC interrupt. */
+
+ uint32_t unused_1[2]; /* Gap. */
+
+ /* Request Queue. */
+ uint32_t req_q_in; /* In-Pointer. */
+ uint32_t req_q_out; /* Out-Pointer. */
+ /* Response Queue. */
+ uint32_t rsp_q_in; /* In-Pointer. */
+ uint32_t rsp_q_out; /* Out-Pointer. */
+ /* Priority Request Queue. */
+ uint32_t preq_q_in; /* In-Pointer. */
+ uint32_t preq_q_out; /* Out-Pointer. */
+
+ uint32_t unused_2[2]; /* Gap. */
+
+ /* ATIO Queue. */
+ uint32_t atio_q_in; /* In-Pointer. */
+ uint32_t atio_q_out; /* Out-Pointer. */
+
+ uint32_t host_status;
+#define HSRX_RISC_INT BIT_15 /* RISC to Host interrupt. */
+#define HSRX_RISC_PAUSED BIT_8 /* RISC Paused. */
+
+ uint32_t hccr; /* Host command & control register. */
+ /* HCCR statuses. */
+#define HCCRX_HOST_INT BIT_6 /* Host to RISC interrupt bit. */
+#define HCCRX_RISC_RESET BIT_5 /* RISC Reset mode bit. */
+ /* HCCR commands. */
+ /* NOOP. */
+#define HCCRX_NOOP 0x00000000
+ /* Set RISC Reset. */
+#define HCCRX_SET_RISC_RESET 0x10000000
+ /* Clear RISC Reset. */
+#define HCCRX_CLR_RISC_RESET 0x20000000
+ /* Set RISC Pause. */
+#define HCCRX_SET_RISC_PAUSE 0x30000000
+ /* Releases RISC Pause. */
+#define HCCRX_REL_RISC_PAUSE 0x40000000
+ /* Set HOST to RISC interrupt. */
+#define HCCRX_SET_HOST_INT 0x50000000
+ /* Clear HOST to RISC interrupt. */
+#define HCCRX_CLR_HOST_INT 0x60000000
+ /* Clear RISC to PCI interrupt. */
+#define HCCRX_CLR_RISC_INT 0xA0000000
+
+ uint32_t gpiod; /* GPIO Data register. */
+
+ /* LED update mask. */
+#define GPDX_LED_UPDATE_MASK (BIT_20|BIT_19|BIT_18)
+ /* Data update mask. */
+#define GPDX_DATA_UPDATE_MASK (BIT_17|BIT_16)
+ /* Data update mask. */
+#define GPDX_DATA_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16)
+ /* LED control mask. */
+#define GPDX_LED_COLOR_MASK (BIT_4|BIT_3|BIT_2)
+ /* LED bit values. Color names as
+ * referenced in fw spec.
+ */
+#define GPDX_LED_YELLOW_ON BIT_2
+#define GPDX_LED_GREEN_ON BIT_3
+#define GPDX_LED_AMBER_ON BIT_4
+ /* Data in/out. */
+#define GPDX_DATA_INOUT (BIT_1|BIT_0)
+
+ uint32_t gpioe; /* GPIO Enable register. */
+ /* Enable update mask. */
+#define GPEX_ENABLE_UPDATE_MASK (BIT_17|BIT_16)
+ /* Enable update mask. */
+#define GPEX_ENABLE_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16)
+ /* Enable. */
+#define GPEX_ENABLE (BIT_1|BIT_0)
+
+ uint32_t iobase_addr; /* I/O Bus Base Address register. */
+
+ uint32_t unused_3[10]; /* Gap. */
+
+ uint16_t mailbox0;
+ uint16_t mailbox1;
+ uint16_t mailbox2;
+ uint16_t mailbox3;
+ uint16_t mailbox4;
+ uint16_t mailbox5;
+ uint16_t mailbox6;
+ uint16_t mailbox7;
+ uint16_t mailbox8;
+ uint16_t mailbox9;
+ uint16_t mailbox10;
+ uint16_t mailbox11;
+ uint16_t mailbox12;
+ uint16_t mailbox13;
+ uint16_t mailbox14;
+ uint16_t mailbox15;
+ uint16_t mailbox16;
+ uint16_t mailbox17;
+ uint16_t mailbox18;
+ uint16_t mailbox19;
+ uint16_t mailbox20;
+ uint16_t mailbox21;
+ uint16_t mailbox22;
+ uint16_t mailbox23;
+ uint16_t mailbox24;
+ uint16_t mailbox25;
+ uint16_t mailbox26;
+ uint16_t mailbox27;
+ uint16_t mailbox28;
+ uint16_t mailbox29;
+ uint16_t mailbox30;
+ uint16_t mailbox31;
+
+ uint32_t iobase_window;
+ uint32_t iobase_c4;
+ uint32_t iobase_c8;
+ uint32_t unused_4_1[6]; /* Gap. */
+ uint32_t iobase_q;
+ uint32_t unused_5[2]; /* Gap. */
+ uint32_t iobase_select;
+ uint32_t unused_6[2]; /* Gap. */
+ uint32_t iobase_sdata;
+};
+/* RISC-RISC semaphore register PCI offet */
+#define RISC_REGISTER_BASE_OFFSET 0x7010
+#define RISC_REGISTER_WINDOW_OFFET 0x6
+
+/* RISC-RISC semaphore/flag register (risc address 0x7016) */
+
+#define RISC_SEMAPHORE 0x1UL
+#define RISC_SEMAPHORE_WE (RISC_SEMAPHORE << 16)
+#define RISC_SEMAPHORE_CLR (RISC_SEMAPHORE_WE | 0x0UL)
+#define RISC_SEMAPHORE_SET (RISC_SEMAPHORE_WE | RISC_SEMAPHORE)
+
+#define RISC_SEMAPHORE_FORCE 0x8000UL
+#define RISC_SEMAPHORE_FORCE_WE (RISC_SEMAPHORE_FORCE << 16)
+#define RISC_SEMAPHORE_FORCE_CLR (RISC_SEMAPHORE_FORCE_WE | 0x0UL)
+#define RISC_SEMAPHORE_FORCE_SET \
+ (RISC_SEMAPHORE_FORCE_WE | RISC_SEMAPHORE_FORCE)
+
+/* RISC semaphore timeouts (ms) */
+#define TIMEOUT_SEMAPHORE 2500
+#define TIMEOUT_SEMAPHORE_FORCE 2000
+#define TIMEOUT_TOTAL_ELAPSED 4500
+
+/* Trace Control *************************************************************/
+
+#define TC_AEN_DISABLE 0
+
+#define TC_EFT_ENABLE 4
+#define TC_EFT_DISABLE 5
+
+#define TC_FCE_ENABLE 8
+#define TC_FCE_OPTIONS 0
+#define TC_FCE_DEFAULT_RX_SIZE 2112
+#define TC_FCE_DEFAULT_TX_SIZE 2112
+#define TC_FCE_DISABLE 9
+#define TC_FCE_DISABLE_TRACE BIT_0
+
+/* MID Support ***************************************************************/
+
+#define MIN_MULTI_ID_FABRIC 64 /* Must be power-of-2. */
+#define MAX_MULTI_ID_FABRIC 256 /* ... */
+
+struct mid_conf_entry_24xx {
+ uint16_t reserved_1;
+
+ /*
+ * BIT 0 = Enable Hard Loop Id
+ * BIT 1 = Acquire Loop ID in LIPA
+ * BIT 2 = ID not Acquired
+ * BIT 3 = Enable VP
+ * BIT 4 = Enable Initiator Mode
+ * BIT 5 = Disable Target Mode
+ * BIT 6-7 = Reserved
+ */
+ uint8_t options;
+
+ uint8_t hard_address;
+
+ uint8_t port_name[WWN_SIZE];
+ uint8_t node_name[WWN_SIZE];
+};
+
+struct mid_init_cb_24xx {
+ struct init_cb_24xx init_cb;
+
+ uint16_t count;
+ uint16_t options;
+
+ struct mid_conf_entry_24xx entries[MAX_MULTI_ID_FABRIC];
+};
+
+
+struct mid_db_entry_24xx {
+ uint16_t status;
+#define MDBS_NON_PARTIC BIT_3
+#define MDBS_ID_ACQUIRED BIT_1
+#define MDBS_ENABLED BIT_0
+
+ uint8_t options;
+ uint8_t hard_address;
+
+ uint8_t port_name[WWN_SIZE];
+ uint8_t node_name[WWN_SIZE];
+
+ uint8_t port_id[3];
+ uint8_t reserved_1;
+};
+
+/*
+ * Virtual Port Control IOCB
+ */
+#define VP_CTRL_IOCB_TYPE 0x30 /* Virtual Port Control entry. */
+struct vp_ctrl_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t vp_idx_failed;
+
+ uint16_t comp_status; /* Completion status. */
+#define CS_VCE_IOCB_ERROR 0x01 /* Error processing IOCB */
+#define CS_VCE_ACQ_ID_ERROR 0x02 /* Error while acquireing ID. */
+#define CS_VCE_BUSY 0x05 /* Firmware not ready to accept cmd. */
+
+ uint16_t command;
+#define VCE_COMMAND_ENABLE_VPS 0x00 /* Enable VPs. */
+#define VCE_COMMAND_DISABLE_VPS 0x08 /* Disable VPs. */
+#define VCE_COMMAND_DISABLE_VPS_REINIT 0x09 /* Disable VPs and reinit link. */
+#define VCE_COMMAND_DISABLE_VPS_LOGO 0x0a /* Disable VPs and LOGO ports. */
+#define VCE_COMMAND_DISABLE_VPS_LOGO_ALL 0x0b /* Disable VPs and LOGO ports. */
+
+ uint16_t vp_count;
+
+ uint8_t vp_idx_map[16];
+ uint16_t flags;
+ uint16_t id;
+ uint16_t reserved_4;
+ uint16_t hopct;
+ uint8_t reserved_5[24];
+};
+
+/*
+ * Modify Virtual Port Configuration IOCB
+ */
+#define VP_CONFIG_IOCB_TYPE 0x31 /* Virtual Port Config entry. */
+struct vp_config_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t handle_count;
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t flags;
+#define CS_VF_BIND_VPORTS_TO_VF BIT_0
+#define CS_VF_SET_QOS_OF_VPORTS BIT_1
+#define CS_VF_SET_HOPS_OF_VPORTS BIT_2
+
+ uint16_t comp_status; /* Completion status. */
+#define CS_VCT_STS_ERROR 0x01 /* Specified VPs were not disabled. */
+#define CS_VCT_CNT_ERROR 0x02 /* Invalid VP count. */
+#define CS_VCT_ERROR 0x03 /* Unknown error. */
+#define CS_VCT_IDX_ERROR 0x02 /* Invalid VP index. */
+#define CS_VCT_BUSY 0x05 /* Firmware not ready to accept cmd. */
+
+ uint8_t command;
+#define VCT_COMMAND_MOD_VPS 0x00 /* Modify VP configurations. */
+#define VCT_COMMAND_MOD_ENABLE_VPS 0x01 /* Modify configuration & enable VPs. */
+
+ uint8_t vp_count;
+
+ uint8_t vp_index1;
+ uint8_t vp_index2;
+
+ uint8_t options_idx1;
+ uint8_t hard_address_idx1;
+ uint16_t reserved_vp1;
+ uint8_t port_name_idx1[WWN_SIZE];
+ uint8_t node_name_idx1[WWN_SIZE];
+
+ uint8_t options_idx2;
+ uint8_t hard_address_idx2;
+ uint16_t reserved_vp2;
+ uint8_t port_name_idx2[WWN_SIZE];
+ uint8_t node_name_idx2[WWN_SIZE];
+ uint16_t id;
+ uint16_t reserved_4;
+ uint16_t hopct;
+ uint8_t reserved_5[2];
+};
+
+#define VP_RPT_ID_IOCB_TYPE 0x32 /* Report ID Acquisition entry. */
+struct vp_rpt_id_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+
+ uint16_t vp_count; /* Format 0 -- | VP setup | VP acq |. */
+ /* Format 1 -- | VP count |. */
+ uint16_t vp_idx; /* Format 0 -- Reserved. */
+ /* Format 1 -- VP status and index. */
+
+ uint8_t port_id[3];
+ uint8_t format;
+
+ uint8_t vp_idx_map[16];
+
+ uint8_t reserved_4[32];
+};
+
+#define VF_EVFP_IOCB_TYPE 0x26 /* Exchange Virtual Fabric Parameters entry. */
+struct vf_evfp_entry_24xx {
+ uint8_t entry_type; /* Entry type. */
+ uint8_t entry_count; /* Entry count. */
+ uint8_t sys_define; /* System defined. */
+ uint8_t entry_status; /* Entry Status. */
+
+ uint32_t handle; /* System handle. */
+ uint16_t comp_status; /* Completion status. */
+ uint16_t timeout; /* timeout */
+ uint16_t adim_tagging_mode;
+
+ uint16_t vfport_id;
+ uint32_t exch_addr;
+
+ uint16_t nport_handle; /* N_PORT handle. */
+ uint16_t control_flags;
+ uint32_t io_parameter_0;
+ uint32_t io_parameter_1;
+ uint32_t tx_address[2]; /* Data segment 0 address. */
+ uint32_t tx_len; /* Data segment 0 length. */
+ uint32_t rx_address[2]; /* Data segment 1 address. */
+ uint32_t rx_len; /* Data segment 1 length. */
+};
+
+/* END MID Support ***********************************************************/
+
+/* Flash Description Table ***************************************************/
+
+struct qla_fdt_layout {
+ uint8_t sig[4];
+ uint16_t version;
+ uint16_t len;
+ uint16_t checksum;
+ uint8_t unused1[2];
+ uint8_t model[16];
+ uint16_t man_id;
+ uint16_t id;
+ uint8_t flags;
+ uint8_t erase_cmd;
+ uint8_t alt_erase_cmd;
+ uint8_t wrt_enable_cmd;
+ uint8_t wrt_enable_bits;
+ uint8_t wrt_sts_reg_cmd;
+ uint8_t unprotect_sec_cmd;
+ uint8_t read_man_id_cmd;
+ uint32_t block_size;
+ uint32_t alt_block_size;
+ uint32_t flash_size;
+ uint32_t wrt_enable_data;
+ uint8_t read_id_addr_len;
+ uint8_t wrt_disable_bits;
+ uint8_t read_dev_id_len;
+ uint8_t chip_erase_cmd;
+ uint16_t read_timeout;
+ uint8_t protect_sec_cmd;
+ uint8_t unused2[65];
+};
+
+/* Flash Layout Table ********************************************************/
+
+struct qla_flt_location {
+ uint8_t sig[4];
+ uint16_t start_lo;
+ uint16_t start_hi;
+ uint8_t version;
+ uint8_t unused[5];
+ uint16_t checksum;
+};
+
+struct qla_flt_header {
+ uint16_t version;
+ uint16_t length;
+ uint16_t checksum;
+ uint16_t unused;
+};
+
+#define FLT_REG_FW 0x01
+#define FLT_REG_BOOT_CODE 0x07
+#define FLT_REG_VPD_0 0x14
+#define FLT_REG_NVRAM_0 0x15
+#define FLT_REG_VPD_1 0x16
+#define FLT_REG_NVRAM_1 0x17
+#define FLT_REG_VPD_2 0xD4
+#define FLT_REG_NVRAM_2 0xD5
+#define FLT_REG_VPD_3 0xD6
+#define FLT_REG_NVRAM_3 0xD7
+#define FLT_REG_FDT 0x1a
+#define FLT_REG_FLT 0x1c
+#define FLT_REG_HW_EVENT_0 0x1d
+#define FLT_REG_HW_EVENT_1 0x1f
+#define FLT_REG_NPIV_CONF_0 0x29
+#define FLT_REG_NPIV_CONF_1 0x2a
+#define FLT_REG_GOLD_FW 0x2f
+#define FLT_REG_FCP_PRIO_0 0x87
+#define FLT_REG_FCP_PRIO_1 0x88
+#define FLT_REG_CNA_FW 0x97
+#define FLT_REG_BOOT_CODE_8044 0xA2
+#define FLT_REG_FCOE_FW 0xA4
+#define FLT_REG_FCOE_NVRAM_0 0xAA
+#define FLT_REG_FCOE_NVRAM_1 0xAC
+
+struct qla_flt_region {
+ uint32_t code;
+ uint32_t size;
+ uint32_t start;
+ uint32_t end;
+};
+
+/* Flash NPIV Configuration Table ********************************************/
+
+struct qla_npiv_header {
+ uint8_t sig[2];
+ uint16_t version;
+ uint16_t entries;
+ uint16_t unused[4];
+ uint16_t checksum;
+};
+
+struct qla_npiv_entry {
+ uint16_t flags;
+ uint16_t vf_id;
+ uint8_t q_qos;
+ uint8_t f_qos;
+ uint16_t unused1;
+ uint8_t port_name[WWN_SIZE];
+ uint8_t node_name[WWN_SIZE];
+};
+
+/* 84XX Support **************************************************************/
+
+#define MBA_ISP84XX_ALERT 0x800f /* Alert Notification. */
+#define A84_PANIC_RECOVERY 0x1
+#define A84_OP_LOGIN_COMPLETE 0x2
+#define A84_DIAG_LOGIN_COMPLETE 0x3
+#define A84_GOLD_LOGIN_COMPLETE 0x4
+
+#define MBC_ISP84XX_RESET 0x3a /* Reset. */
+
+#define FSTATE_REMOTE_FC_DOWN BIT_0
+#define FSTATE_NSL_LINK_DOWN BIT_1
+#define FSTATE_IS_DIAG_FW BIT_2
+#define FSTATE_LOGGED_IN BIT_3
+#define FSTATE_WAITING_FOR_VERIFY BIT_4
+
+#define VERIFY_CHIP_IOCB_TYPE 0x1B
+struct verify_chip_entry_84xx {
+ uint8_t entry_type;
+ uint8_t entry_count;
+ uint8_t sys_defined;
+ uint8_t entry_status;
+
+ uint32_t handle;
+
+ uint16_t options;
+#define VCO_DONT_UPDATE_FW BIT_0
+#define VCO_FORCE_UPDATE BIT_1
+#define VCO_DONT_RESET_UPDATE BIT_2
+#define VCO_DIAG_FW BIT_3
+#define VCO_END_OF_DATA BIT_14
+#define VCO_ENABLE_DSD BIT_15
+
+ uint16_t reserved_1;
+
+ uint16_t data_seg_cnt;
+ uint16_t reserved_2[3];
+
+ uint32_t fw_ver;
+ uint32_t exchange_address;
+
+ uint32_t reserved_3[3];
+ uint32_t fw_size;
+ uint32_t fw_seq_size;
+ uint32_t relative_offset;
+
+ uint32_t dseg_address[2];
+ uint32_t dseg_length;
+};
+
+struct verify_chip_rsp_84xx {
+ uint8_t entry_type;
+ uint8_t entry_count;
+ uint8_t sys_defined;
+ uint8_t entry_status;
+
+ uint32_t handle;
+
+ uint16_t comp_status;
+#define CS_VCS_CHIP_FAILURE 0x3
+#define CS_VCS_BAD_EXCHANGE 0x8
+#define CS_VCS_SEQ_COMPLETEi 0x40
+
+ uint16_t failure_code;
+#define VFC_CHECKSUM_ERROR 0x1
+#define VFC_INVALID_LEN 0x2
+#define VFC_ALREADY_IN_PROGRESS 0x8
+
+ uint16_t reserved_1[4];
+
+ uint32_t fw_ver;
+ uint32_t exchange_address;
+
+ uint32_t reserved_2[6];
+};
+
+#define ACCESS_CHIP_IOCB_TYPE 0x2B
+struct access_chip_84xx {
+ uint8_t entry_type;
+ uint8_t entry_count;
+ uint8_t sys_defined;
+ uint8_t entry_status;
+
+ uint32_t handle;
+
+ uint16_t options;
+#define ACO_DUMP_MEMORY 0x0
+#define ACO_LOAD_MEMORY 0x1
+#define ACO_CHANGE_CONFIG_PARAM 0x2
+#define ACO_REQUEST_INFO 0x3
+
+ uint16_t reserved1;
+
+ uint16_t dseg_count;
+ uint16_t reserved2[3];
+
+ uint32_t parameter1;
+ uint32_t parameter2;
+ uint32_t parameter3;
+
+ uint32_t reserved3[3];
+ uint32_t total_byte_cnt;
+ uint32_t reserved4;
+
+ uint32_t dseg_address[2];
+ uint32_t dseg_length;
+};
+
+struct access_chip_rsp_84xx {
+ uint8_t entry_type;
+ uint8_t entry_count;
+ uint8_t sys_defined;
+ uint8_t entry_status;
+
+ uint32_t handle;
+
+ uint16_t comp_status;
+ uint16_t failure_code;
+ uint32_t residual_count;
+
+ uint32_t reserved[12];
+};
+
+/* 81XX Support **************************************************************/
+
+#define MBA_DCBX_START 0x8016
+#define MBA_DCBX_COMPLETE 0x8030
+#define MBA_FCF_CONF_ERR 0x8031
+#define MBA_DCBX_PARAM_UPDATE 0x8032
+#define MBA_IDC_COMPLETE 0x8100
+#define MBA_IDC_NOTIFY 0x8101
+#define MBA_IDC_TIME_EXT 0x8102
+
+#define MBC_IDC_ACK 0x101
+#define MBC_RESTART_MPI_FW 0x3d
+#define MBC_FLASH_ACCESS_CTRL 0x3e /* Control flash access. */
+#define MBC_GET_XGMAC_STATS 0x7a
+#define MBC_GET_DCBX_PARAMS 0x51
+
+/*
+ * ISP83xx mailbox commands
+ */
+#define MBC_WRITE_REMOTE_REG 0x0001 /* Write remote register */
+#define MBC_READ_REMOTE_REG 0x0009 /* Read remote register */
+#define MBC_RESTART_NIC_FIRMWARE 0x003d /* Restart NIC firmware */
+#define MBC_SET_ACCESS_CONTROL 0x003e /* Access control command */
+
+/* Flash access control option field bit definitions */
+#define FAC_OPT_FORCE_SEMAPHORE BIT_15
+#define FAC_OPT_REQUESTOR_ID BIT_14
+#define FAC_OPT_CMD_SUBCODE 0xff
+
+/* Flash access control command subcodes */
+#define FAC_OPT_CMD_WRITE_PROTECT 0x00
+#define FAC_OPT_CMD_WRITE_ENABLE 0x01
+#define FAC_OPT_CMD_ERASE_SECTOR 0x02
+#define FAC_OPT_CMD_LOCK_SEMAPHORE 0x03
+#define FAC_OPT_CMD_UNLOCK_SEMAPHORE 0x04
+#define FAC_OPT_CMD_GET_SECTOR_SIZE 0x05
+
+struct nvram_81xx {
+ /* NVRAM header. */
+ uint8_t id[4];
+ uint16_t nvram_version;
+ uint16_t reserved_0;
+
+ /* Firmware Initialization Control Block. */
+ uint16_t version;
+ uint16_t reserved_1;
+ uint16_t frame_payload_size;
+ uint16_t execution_throttle;
+ uint16_t exchange_count;
+ uint16_t reserved_2;
+
+ uint8_t port_name[WWN_SIZE];
+ uint8_t node_name[WWN_SIZE];
+
+ uint16_t login_retry_count;
+ uint16_t reserved_3;
+ uint16_t interrupt_delay_timer;
+ uint16_t login_timeout;
+
+ uint32_t firmware_options_1;
+ uint32_t firmware_options_2;
+ uint32_t firmware_options_3;
+
+ uint16_t reserved_4[4];
+
+ /* Offset 64. */
+ uint8_t enode_mac[6];
+ uint16_t reserved_5[5];
+
+ /* Offset 80. */
+ uint16_t reserved_6[24];
+
+ /* Offset 128. */
+ uint16_t ex_version;
+ uint8_t prio_fcf_matching_flags;
+ uint8_t reserved_6_1[3];
+ uint16_t pri_fcf_vlan_id;
+ uint8_t pri_fcf_fabric_name[8];
+ uint16_t reserved_6_2[7];
+ uint8_t spma_mac_addr[6];
+ uint16_t reserved_6_3[14];
+
+ /* Offset 192. */
+ uint16_t reserved_7[32];
+
+ /*
+ * BIT 0 = Enable spinup delay
+ * BIT 1 = Disable BIOS
+ * BIT 2 = Enable Memory Map BIOS
+ * BIT 3 = Enable Selectable Boot
+ * BIT 4 = Disable RISC code load
+ * BIT 5 = Disable Serdes
+ * BIT 6 = Opt boot mode
+ * BIT 7 = Interrupt enable
+ *
+ * BIT 8 = EV Control enable
+ * BIT 9 = Enable lip reset
+ * BIT 10 = Enable lip full login
+ * BIT 11 = Enable target reset
+ * BIT 12 = Stop firmware
+ * BIT 13 = Enable nodename option
+ * BIT 14 = Default WWPN valid
+ * BIT 15 = Enable alternate WWN
+ *
+ * BIT 16 = CLP LUN string
+ * BIT 17 = CLP Target string
+ * BIT 18 = CLP BIOS enable string
+ * BIT 19 = CLP Serdes string
+ * BIT 20 = CLP WWPN string
+ * BIT 21 = CLP WWNN string
+ * BIT 22 =
+ * BIT 23 =
+ * BIT 24 = Keep WWPN
+ * BIT 25 = Temp WWPN
+ * BIT 26-31 =
+ */
+ uint32_t host_p;
+
+ uint8_t alternate_port_name[WWN_SIZE];
+ uint8_t alternate_node_name[WWN_SIZE];
+
+ uint8_t boot_port_name[WWN_SIZE];
+ uint16_t boot_lun_number;
+ uint16_t reserved_8;
+
+ uint8_t alt1_boot_port_name[WWN_SIZE];
+ uint16_t alt1_boot_lun_number;
+ uint16_t reserved_9;
+
+ uint8_t alt2_boot_port_name[WWN_SIZE];
+ uint16_t alt2_boot_lun_number;
+ uint16_t reserved_10;
+
+ uint8_t alt3_boot_port_name[WWN_SIZE];
+ uint16_t alt3_boot_lun_number;
+ uint16_t reserved_11;
+
+ /*
+ * BIT 0 = Selective Login
+ * BIT 1 = Alt-Boot Enable
+ * BIT 2 = Reserved
+ * BIT 3 = Boot Order List
+ * BIT 4 = Reserved
+ * BIT 5 = Selective LUN
+ * BIT 6 = Reserved
+ * BIT 7-31 =
+ */
+ uint32_t efi_parameters;
+
+ uint8_t reset_delay;
+ uint8_t reserved_12;
+ uint16_t reserved_13;
+
+ uint16_t boot_id_number;
+ uint16_t reserved_14;
+
+ uint16_t max_luns_per_target;
+ uint16_t reserved_15;
+
+ uint16_t port_down_retry_count;
+ uint16_t link_down_timeout;
+
+ /* FCode parameters. */
+ uint16_t fcode_parameter;
+
+ uint16_t reserved_16[3];
+
+ /* Offset 352. */
+ uint8_t reserved_17[4];
+ uint16_t reserved_18[5];
+ uint8_t reserved_19[2];
+ uint16_t reserved_20[8];
+
+ /* Offset 384. */
+ uint8_t reserved_21[16];
+ uint16_t reserved_22[3];
+
+ /*
+ * BIT 0 = Extended BB credits for LR
+ * BIT 1 = Virtual Fabric Enable
+ * BIT 2 = Enhanced Features Unused
+ * BIT 3-7 = Enhanced Features Reserved
+ */
+ /* Enhanced Features */
+ uint8_t enhanced_features;
+
+ uint8_t reserved_23;
+ uint16_t reserved_24[4];
+
+ /* Offset 416. */
+ uint16_t reserved_25[32];
+
+ /* Offset 480. */
+ uint8_t model_name[16];
+
+ /* Offset 496. */
+ uint16_t feature_mask_l;
+ uint16_t feature_mask_h;
+ uint16_t reserved_26[2];
+
+ uint16_t subsystem_vendor_id;
+ uint16_t subsystem_device_id;
+
+ uint32_t checksum;
+};
+
+/*
+ * ISP Initialization Control Block.
+ * Little endian except where noted.
+ */
+#define ICB_VERSION 1
+struct init_cb_81xx {
+ uint16_t version;
+ uint16_t reserved_1;
+
+ uint16_t frame_payload_size;
+ uint16_t execution_throttle;
+ uint16_t exchange_count;
+
+ uint16_t reserved_2;
+
+ uint8_t port_name[WWN_SIZE]; /* Big endian. */
+ uint8_t node_name[WWN_SIZE]; /* Big endian. */
+
+ uint16_t response_q_inpointer;
+ uint16_t request_q_outpointer;
+
+ uint16_t login_retry_count;
+
+ uint16_t prio_request_q_outpointer;
+
+ uint16_t response_q_length;
+ uint16_t request_q_length;
+
+ uint16_t reserved_3;
+
+ uint16_t prio_request_q_length;
+
+ uint32_t request_q_address[2];
+ uint32_t response_q_address[2];
+ uint32_t prio_request_q_address[2];
+
+ uint8_t reserved_4[8];
+
+ uint16_t atio_q_inpointer;
+ uint16_t atio_q_length;
+ uint32_t atio_q_address[2];
+
+ uint16_t interrupt_delay_timer; /* 100us increments. */
+ uint16_t login_timeout;
+
+ /*
+ * BIT 0-3 = Reserved
+ * BIT 4 = Enable Target Mode
+ * BIT 5 = Disable Initiator Mode
+ * BIT 6 = Reserved
+ * BIT 7 = Reserved
+ *
+ * BIT 8-13 = Reserved
+ * BIT 14 = Node Name Option
+ * BIT 15-31 = Reserved
+ */
+ uint32_t firmware_options_1;
+
+ /*
+ * BIT 0 = Operation Mode bit 0
+ * BIT 1 = Operation Mode bit 1
+ * BIT 2 = Operation Mode bit 2
+ * BIT 3 = Operation Mode bit 3
+ * BIT 4-7 = Reserved
+ *
+ * BIT 8 = Enable Class 2
+ * BIT 9 = Enable ACK0
+ * BIT 10 = Reserved
+ * BIT 11 = Enable FC-SP Security
+ * BIT 12 = FC Tape Enable
+ * BIT 13 = Reserved
+ * BIT 14 = Enable Target PRLI Control
+ * BIT 15-31 = Reserved
+ */
+ uint32_t firmware_options_2;
+
+ /*
+ * BIT 0-3 = Reserved
+ * BIT 4 = FCP RSP Payload bit 0
+ * BIT 5 = FCP RSP Payload bit 1
+ * BIT 6 = Enable Receive Out-of-Order data frame handling
+ * BIT 7 = Reserved
+ *
+ * BIT 8 = Reserved
+ * BIT 9 = Enable Out-of-Order FCP_XFER_RDY relative offset handling
+ * BIT 10-16 = Reserved
+ * BIT 17 = Enable multiple FCFs
+ * BIT 18-20 = MAC addressing mode
+ * BIT 21-25 = Ethernet data rate
+ * BIT 26 = Enable ethernet header rx IOCB for ATIO q
+ * BIT 27 = Enable ethernet header rx IOCB for response q
+ * BIT 28 = SPMA selection bit 0
+ * BIT 28 = SPMA selection bit 1
+ * BIT 30-31 = Reserved
+ */
+ uint32_t firmware_options_3;
+
+ uint8_t reserved_5[8];
+
+ uint8_t enode_mac[6];
+
+ uint8_t reserved_6[10];
+};
+
+struct mid_init_cb_81xx {
+ struct init_cb_81xx init_cb;
+
+ uint16_t count;
+ uint16_t options;
+
+ struct mid_conf_entry_24xx entries[MAX_MULTI_ID_FABRIC];
+};
+
+struct ex_init_cb_81xx {
+ uint16_t ex_version;
+ uint8_t prio_fcf_matching_flags;
+ uint8_t reserved_1[3];
+ uint16_t pri_fcf_vlan_id;
+ uint8_t pri_fcf_fabric_name[8];
+ uint16_t reserved_2[7];
+ uint8_t spma_mac_addr[6];
+ uint16_t reserved_3[14];
+};
+
+#define FARX_ACCESS_FLASH_CONF_81XX 0x7FFD0000
+#define FARX_ACCESS_FLASH_DATA_81XX 0x7F800000
+
+/* FCP priority config defines *************************************/
+/* operations */
+#define QLFC_FCP_PRIO_DISABLE 0x0
+#define QLFC_FCP_PRIO_ENABLE 0x1
+#define QLFC_FCP_PRIO_GET_CONFIG 0x2
+#define QLFC_FCP_PRIO_SET_CONFIG 0x3
+
+struct qla_fcp_prio_entry {
+ uint16_t flags; /* Describes parameter(s) in FCP */
+ /* priority entry that are valid */
+#define FCP_PRIO_ENTRY_VALID 0x1
+#define FCP_PRIO_ENTRY_TAG_VALID 0x2
+#define FCP_PRIO_ENTRY_SPID_VALID 0x4
+#define FCP_PRIO_ENTRY_DPID_VALID 0x8
+#define FCP_PRIO_ENTRY_LUNB_VALID 0x10
+#define FCP_PRIO_ENTRY_LUNE_VALID 0x20
+#define FCP_PRIO_ENTRY_SWWN_VALID 0x40
+#define FCP_PRIO_ENTRY_DWWN_VALID 0x80
+ uint8_t tag; /* Priority value */
+ uint8_t reserved; /* Reserved for future use */
+ uint32_t src_pid; /* Src port id. high order byte */
+ /* unused; -1 (wild card) */
+ uint32_t dst_pid; /* Src port id. high order byte */
+ /* unused; -1 (wild card) */
+ uint16_t lun_beg; /* 1st lun num of lun range. */
+ /* -1 (wild card) */
+ uint16_t lun_end; /* 2nd lun num of lun range. */
+ /* -1 (wild card) */
+ uint8_t src_wwpn[8]; /* Source WWPN: -1 (wild card) */
+ uint8_t dst_wwpn[8]; /* Destination WWPN: -1 (wild card) */
+};
+
+struct qla_fcp_prio_cfg {
+ uint8_t signature[4]; /* "HQOS" signature of config data */
+ uint16_t version; /* 1: Initial version */
+ uint16_t length; /* config data size in num bytes */
+ uint16_t checksum; /* config data bytes checksum */
+ uint16_t num_entries; /* Number of entries */
+ uint16_t size_of_entry; /* Size of each entry in num bytes */
+ uint8_t attributes; /* enable/disable, persistence */
+#define FCP_PRIO_ATTR_DISABLE 0x0
+#define FCP_PRIO_ATTR_ENABLE 0x1
+#define FCP_PRIO_ATTR_PERSIST 0x2
+ uint8_t reserved; /* Reserved for future use */
+#define FCP_PRIO_CFG_HDR_SIZE 0x10
+ struct qla_fcp_prio_entry entry[1]; /* fcp priority entries */
+#define FCP_PRIO_CFG_ENTRY_SIZE 0x20
+};
+
+#define FCP_PRIO_CFG_SIZE (32*1024) /* fcp prio data per port*/
+
+/* 25XX Support ****************************************************/
+#define FA_FCP_PRIO0_ADDR_25 0x3C000
+#define FA_FCP_PRIO1_ADDR_25 0x3E000
+
+/* 81XX Flash locations -- occupies second 2MB region. */
+#define FA_BOOT_CODE_ADDR_81 0x80000
+#define FA_RISC_CODE_ADDR_81 0xA0000
+#define FA_FW_AREA_ADDR_81 0xC0000
+#define FA_VPD_NVRAM_ADDR_81 0xD0000
+#define FA_VPD0_ADDR_81 0xD0000
+#define FA_VPD1_ADDR_81 0xD0400
+#define FA_NVRAM0_ADDR_81 0xD0080
+#define FA_NVRAM1_ADDR_81 0xD0180
+#define FA_FEATURE_ADDR_81 0xD4000
+#define FA_FLASH_DESCR_ADDR_81 0xD8000
+#define FA_FLASH_LAYOUT_ADDR_81 0xD8400
+#define FA_HW_EVENT0_ADDR_81 0xDC000
+#define FA_HW_EVENT1_ADDR_81 0xDC400
+#define FA_NPIV_CONF0_ADDR_81 0xD1000
+#define FA_NPIV_CONF1_ADDR_81 0xD2000
+
+/* 83XX Flash locations -- occupies second 8MB region. */
+#define FA_FLASH_LAYOUT_ADDR_83 0xFC400
+
+#endif
Code Review / kvmfornfv.git / blobdiff