--- /dev/null
+/*
+ * PMC-Sierra SPCv/ve 8088/8089 SAS/SATA based host adapters driver
+ *
+ * Copyright (c) 2008-2009 USI Co., Ltd.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions, and the following disclaimer,
+ * without modification.
+ * 2. Redistributions in binary form must reproduce at minimum a disclaimer
+ * substantially similar to the "NO WARRANTY" disclaimer below
+ * ("Disclaimer") and any redistribution must be conditioned upon
+ * including a substantially similar Disclaimer requirement for further
+ * binary redistribution.
+ * 3. Neither the names of the above-listed copyright holders nor the names
+ * of any contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * NO WARRANTY
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
+ * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGES.
+ *
+ */
+
+#ifndef _PMC8001_REG_H_
+#define _PMC8001_REG_H_
+
+#include <linux/types.h>
+#include <scsi/libsas.h>
+
+/* for Request Opcode of IOMB */
+#define OPC_INB_ECHO 1 /* 0x000 */
+#define OPC_INB_PHYSTART 4 /* 0x004 */
+#define OPC_INB_PHYSTOP 5 /* 0x005 */
+#define OPC_INB_SSPINIIOSTART 6 /* 0x006 */
+#define OPC_INB_SSPINITMSTART 7 /* 0x007 */
+/* 0x8 RESV IN SPCv */
+#define OPC_INB_RSVD 8 /* 0x008 */
+#define OPC_INB_DEV_HANDLE_ACCEPT 9 /* 0x009 */
+#define OPC_INB_SSPTGTIOSTART 10 /* 0x00A */
+#define OPC_INB_SSPTGTRSPSTART 11 /* 0x00B */
+/* 0xC, 0xD, 0xE removed in SPCv */
+#define OPC_INB_SSP_ABORT 15 /* 0x00F */
+#define OPC_INB_DEREG_DEV_HANDLE 16 /* 0x010 */
+#define OPC_INB_GET_DEV_HANDLE 17 /* 0x011 */
+#define OPC_INB_SMP_REQUEST 18 /* 0x012 */
+/* 0x13 SMP_RESPONSE is removed in SPCv */
+#define OPC_INB_SMP_ABORT 20 /* 0x014 */
+/* 0x16 RESV IN SPCv */
+#define OPC_INB_RSVD1 22 /* 0x016 */
+#define OPC_INB_SATA_HOST_OPSTART 23 /* 0x017 */
+#define OPC_INB_SATA_ABORT 24 /* 0x018 */
+#define OPC_INB_LOCAL_PHY_CONTROL 25 /* 0x019 */
+/* 0x1A RESV IN SPCv */
+#define OPC_INB_RSVD2 26 /* 0x01A */
+#define OPC_INB_FW_FLASH_UPDATE 32 /* 0x020 */
+#define OPC_INB_GPIO 34 /* 0x022 */
+#define OPC_INB_SAS_DIAG_MODE_START_END 35 /* 0x023 */
+#define OPC_INB_SAS_DIAG_EXECUTE 36 /* 0x024 */
+/* 0x25 RESV IN SPCv */
+#define OPC_INB_RSVD3 37 /* 0x025 */
+#define OPC_INB_GET_TIME_STAMP 38 /* 0x026 */
+#define OPC_INB_PORT_CONTROL 39 /* 0x027 */
+#define OPC_INB_GET_NVMD_DATA 40 /* 0x028 */
+#define OPC_INB_SET_NVMD_DATA 41 /* 0x029 */
+#define OPC_INB_SET_DEVICE_STATE 42 /* 0x02A */
+#define OPC_INB_GET_DEVICE_STATE 43 /* 0x02B */
+#define OPC_INB_SET_DEV_INFO 44 /* 0x02C */
+/* 0x2D RESV IN SPCv */
+#define OPC_INB_RSVD4 45 /* 0x02D */
+#define OPC_INB_SGPIO_REGISTER 46 /* 0x02E */
+#define OPC_INB_PCIE_DIAG_EXEC 47 /* 0x02F */
+#define OPC_INB_SET_CONTROLLER_CONFIG 48 /* 0x030 */
+#define OPC_INB_GET_CONTROLLER_CONFIG 49 /* 0x031 */
+#define OPC_INB_REG_DEV 50 /* 0x032 */
+#define OPC_INB_SAS_HW_EVENT_ACK 51 /* 0x033 */
+#define OPC_INB_GET_DEVICE_INFO 52 /* 0x034 */
+#define OPC_INB_GET_PHY_PROFILE 53 /* 0x035 */
+#define OPC_INB_FLASH_OP_EXT 54 /* 0x036 */
+#define OPC_INB_SET_PHY_PROFILE 55 /* 0x037 */
+#define OPC_INB_KEK_MANAGEMENT 256 /* 0x100 */
+#define OPC_INB_DEK_MANAGEMENT 257 /* 0x101 */
+#define OPC_INB_SSP_INI_DIF_ENC_IO 258 /* 0x102 */
+#define OPC_INB_SATA_DIF_ENC_IO 259 /* 0x103 */
+
+/* for Response Opcode of IOMB */
+#define OPC_OUB_ECHO 1 /* 0x001 */
+#define OPC_OUB_RSVD 4 /* 0x004 */
+#define OPC_OUB_SSP_COMP 5 /* 0x005 */
+#define OPC_OUB_SMP_COMP 6 /* 0x006 */
+#define OPC_OUB_LOCAL_PHY_CNTRL 7 /* 0x007 */
+#define OPC_OUB_RSVD1 10 /* 0x00A */
+#define OPC_OUB_DEREG_DEV 11 /* 0x00B */
+#define OPC_OUB_GET_DEV_HANDLE 12 /* 0x00C */
+#define OPC_OUB_SATA_COMP 13 /* 0x00D */
+#define OPC_OUB_SATA_EVENT 14 /* 0x00E */
+#define OPC_OUB_SSP_EVENT 15 /* 0x00F */
+#define OPC_OUB_RSVD2 16 /* 0x010 */
+/* 0x11 - SMP_RECEIVED Notification removed in SPCv*/
+#define OPC_OUB_SSP_RECV_EVENT 18 /* 0x012 */
+#define OPC_OUB_RSVD3 19 /* 0x013 */
+#define OPC_OUB_FW_FLASH_UPDATE 20 /* 0x014 */
+#define OPC_OUB_GPIO_RESPONSE 22 /* 0x016 */
+#define OPC_OUB_GPIO_EVENT 23 /* 0x017 */
+#define OPC_OUB_GENERAL_EVENT 24 /* 0x018 */
+#define OPC_OUB_SSP_ABORT_RSP 26 /* 0x01A */
+#define OPC_OUB_SATA_ABORT_RSP 27 /* 0x01B */
+#define OPC_OUB_SAS_DIAG_MODE_START_END 28 /* 0x01C */
+#define OPC_OUB_SAS_DIAG_EXECUTE 29 /* 0x01D */
+#define OPC_OUB_GET_TIME_STAMP 30 /* 0x01E */
+#define OPC_OUB_RSVD4 31 /* 0x01F */
+#define OPC_OUB_PORT_CONTROL 32 /* 0x020 */
+#define OPC_OUB_SKIP_ENTRY 33 /* 0x021 */
+#define OPC_OUB_SMP_ABORT_RSP 34 /* 0x022 */
+#define OPC_OUB_GET_NVMD_DATA 35 /* 0x023 */
+#define OPC_OUB_SET_NVMD_DATA 36 /* 0x024 */
+#define OPC_OUB_DEVICE_HANDLE_REMOVAL 37 /* 0x025 */
+#define OPC_OUB_SET_DEVICE_STATE 38 /* 0x026 */
+#define OPC_OUB_GET_DEVICE_STATE 39 /* 0x027 */
+#define OPC_OUB_SET_DEV_INFO 40 /* 0x028 */
+#define OPC_OUB_RSVD5 41 /* 0x029 */
+#define OPC_OUB_HW_EVENT 1792 /* 0x700 */
+#define OPC_OUB_DEV_HANDLE_ARRIV 1824 /* 0x720 */
+#define OPC_OUB_THERM_HW_EVENT 1840 /* 0x730 */
+#define OPC_OUB_SGPIO_RESP 2094 /* 0x82E */
+#define OPC_OUB_PCIE_DIAG_EXECUTE 2095 /* 0x82F */
+#define OPC_OUB_DEV_REGIST 2098 /* 0x832 */
+#define OPC_OUB_SAS_HW_EVENT_ACK 2099 /* 0x833 */
+#define OPC_OUB_GET_DEVICE_INFO 2100 /* 0x834 */
+/* spcv specific commands */
+#define OPC_OUB_PHY_START_RESP 2052 /* 0x804 */
+#define OPC_OUB_PHY_STOP_RESP 2053 /* 0x805 */
+#define OPC_OUB_SET_CONTROLLER_CONFIG 2096 /* 0x830 */
+#define OPC_OUB_GET_CONTROLLER_CONFIG 2097 /* 0x831 */
+#define OPC_OUB_GET_PHY_PROFILE 2101 /* 0x835 */
+#define OPC_OUB_FLASH_OP_EXT 2102 /* 0x836 */
+#define OPC_OUB_SET_PHY_PROFILE 2103 /* 0x837 */
+#define OPC_OUB_KEK_MANAGEMENT_RESP 2304 /* 0x900 */
+#define OPC_OUB_DEK_MANAGEMENT_RESP 2305 /* 0x901 */
+#define OPC_OUB_SSP_COALESCED_COMP_RESP 2306 /* 0x902 */
+
+/* for phy start*/
+#define SSC_DISABLE_15 (0x01 << 16)
+#define SSC_DISABLE_30 (0x02 << 16)
+#define SSC_DISABLE_60 (0x04 << 16)
+#define SAS_ASE (0x01 << 15)
+#define SPINHOLD_DISABLE (0x00 << 14)
+#define SPINHOLD_ENABLE (0x01 << 14)
+#define LINKMODE_SAS (0x01 << 12)
+#define LINKMODE_DSATA (0x02 << 12)
+#define LINKMODE_AUTO (0x03 << 12)
+#define LINKRATE_15 (0x01 << 8)
+#define LINKRATE_30 (0x02 << 8)
+#define LINKRATE_60 (0x06 << 8)
+#define LINKRATE_120 (0x08 << 8)
+
+/* phy_profile */
+#define SAS_PHY_ANALOG_SETTINGS_PAGE 0x04
+#define PHY_DWORD_LENGTH 0xC
+
+/* Thermal related */
+#define THERMAL_ENABLE 0x1
+#define THERMAL_LOG_ENABLE 0x1
+#define THERMAL_OP_CODE 0x6
+#define LTEMPHIL 70
+#define RTEMPHIL 100
+
+/* Encryption info */
+#define SCRATCH_PAD3_ENC_DISABLED 0x00000000
+#define SCRATCH_PAD3_ENC_DIS_ERR 0x00000001
+#define SCRATCH_PAD3_ENC_ENA_ERR 0x00000002
+#define SCRATCH_PAD3_ENC_READY 0x00000003
+#define SCRATCH_PAD3_ENC_MASK SCRATCH_PAD3_ENC_READY
+
+#define SCRATCH_PAD3_XTS_ENABLED (1 << 14)
+#define SCRATCH_PAD3_SMA_ENABLED (1 << 4)
+#define SCRATCH_PAD3_SMB_ENABLED (1 << 5)
+#define SCRATCH_PAD3_SMF_ENABLED 0
+#define SCRATCH_PAD3_SM_MASK 0x000000F0
+#define SCRATCH_PAD3_ERR_CODE 0x00FF0000
+
+#define SEC_MODE_SMF 0x0
+#define SEC_MODE_SMA 0x100
+#define SEC_MODE_SMB 0x200
+#define CIPHER_MODE_ECB 0x00000001
+#define CIPHER_MODE_XTS 0x00000002
+#define KEK_MGMT_SUBOP_KEYCARDUPDATE 0x4
+
+/* SAS protocol timer configuration page */
+#define SAS_PROTOCOL_TIMER_CONFIG_PAGE 0x04
+#define STP_MCT_TMO 32
+#define SSP_MCT_TMO 32
+#define SAS_MAX_OPEN_TIME 5
+#define SMP_MAX_CONN_TIMER 0xFF
+#define STP_FRM_TIMER 0
+#define STP_IDLE_TIME 5 /* 5 us; controller default */
+#define SAS_MFD 0
+#define SAS_OPNRJT_RTRY_INTVL 2
+#define SAS_DOPNRJT_RTRY_TMO 128
+#define SAS_COPNRJT_RTRY_TMO 128
+
+/* for phy state */
+#define PHY_STATE_LINK_UP_SPCV 0x2
+/*
+ Making ORR bigger than IT NEXUS LOSS which is 2000000us = 2 second.
+ Assuming a bigger value 3 second, 3000000/128 = 23437.5 where 128
+ is DOPNRJT_RTRY_TMO
+*/
+#define SAS_DOPNRJT_RTRY_THR 23438
+#define SAS_COPNRJT_RTRY_THR 23438
+#define SAS_MAX_AIP 0x200000
+#define IT_NEXUS_TIMEOUT 0x7D0
+#define PORT_RECOVERY_TIMEOUT ((IT_NEXUS_TIMEOUT/100) + 30)
+
+struct mpi_msg_hdr {
+ __le32 header; /* Bits [11:0] - Message operation code */
+ /* Bits [15:12] - Message Category */
+ /* Bits [21:16] - Outboundqueue ID for the
+ operation completion message */
+ /* Bits [23:22] - Reserved */
+ /* Bits [28:24] - Buffer Count, indicates how
+ many buffer are allocated for the massage */
+ /* Bits [30:29] - Reserved */
+ /* Bits [31] - Message Valid bit */
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of PHY Start Command
+ * use to describe enable the phy (128 bytes)
+ */
+struct phy_start_req {
+ __le32 tag;
+ __le32 ase_sh_lm_slr_phyid;
+ struct sas_identify_frame sas_identify; /* 28 Bytes */
+ __le32 spasti;
+ u32 reserved[21];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of PHY Start Command
+ * use to disable the phy (128 bytes)
+ */
+struct phy_stop_req {
+ __le32 tag;
+ __le32 phy_id;
+ u32 reserved[29];
+} __attribute__((packed, aligned(4)));
+
+/* set device bits fis - device to host */
+struct set_dev_bits_fis {
+ u8 fis_type; /* 0xA1*/
+ u8 n_i_pmport;
+ /* b7 : n Bit. Notification bit. If set device needs attention. */
+ /* b6 : i Bit. Interrupt Bit */
+ /* b5-b4: reserved2 */
+ /* b3-b0: PM Port */
+ u8 status;
+ u8 error;
+ u32 _r_a;
+} __attribute__ ((packed));
+/* PIO setup FIS - device to host */
+struct pio_setup_fis {
+ u8 fis_type; /* 0x5f */
+ u8 i_d_pmPort;
+ /* b7 : reserved */
+ /* b6 : i bit. Interrupt bit */
+ /* b5 : d bit. data transfer direction. set to 1 for device to host
+ xfer */
+ /* b4 : reserved */
+ /* b3-b0: PM Port */
+ u8 status;
+ u8 error;
+ u8 lbal;
+ u8 lbam;
+ u8 lbah;
+ u8 device;
+ u8 lbal_exp;
+ u8 lbam_exp;
+ u8 lbah_exp;
+ u8 _r_a;
+ u8 sector_count;
+ u8 sector_count_exp;
+ u8 _r_b;
+ u8 e_status;
+ u8 _r_c[2];
+ u8 transfer_count;
+} __attribute__ ((packed));
+
+/*
+ * brief the data structure of SATA Completion Response
+ * use to describe the sata task response (64 bytes)
+ */
+struct sata_completion_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 param;
+ u32 sata_resp[12];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of SAS HW Event Notification
+ * use to alert the host about the hardware event(64 bytes)
+ */
+/* updated outbound struct for spcv */
+
+struct hw_event_resp {
+ __le32 lr_status_evt_portid;
+ __le32 evt_param;
+ __le32 phyid_npip_portstate;
+ struct sas_identify_frame sas_identify;
+ struct dev_to_host_fis sata_fis;
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure for thermal event notification
+ */
+
+struct thermal_hw_event {
+ __le32 thermal_event;
+ __le32 rht_lht;
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of REGISTER DEVICE Command
+ * use to describe MPI REGISTER DEVICE Command (64 bytes)
+ */
+
+struct reg_dev_req {
+ __le32 tag;
+ __le32 phyid_portid;
+ __le32 dtype_dlr_mcn_ir_retry;
+ __le32 firstburstsize_ITNexustimeout;
+ u8 sas_addr[SAS_ADDR_SIZE];
+ __le32 upper_device_id;
+ u32 reserved[24];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of DEREGISTER DEVICE Command
+ * use to request spc to remove all internal resources associated
+ * with the device id (64 bytes)
+ */
+
+struct dereg_dev_req {
+ __le32 tag;
+ __le32 device_id;
+ u32 reserved[29];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of DEVICE_REGISTRATION Response
+ * use to notify the completion of the device registration (64 bytes)
+ */
+struct dev_reg_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 device_id;
+ u32 reserved[12];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of Local PHY Control Command
+ * use to issue PHY CONTROL to local phy (64 bytes)
+ */
+struct local_phy_ctl_req {
+ __le32 tag;
+ __le32 phyop_phyid;
+ u32 reserved1[29];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of Local Phy Control Response
+ * use to describe MPI Local Phy Control Response (64 bytes)
+ */
+ struct local_phy_ctl_resp {
+ __le32 tag;
+ __le32 phyop_phyid;
+ __le32 status;
+ u32 reserved[12];
+} __attribute__((packed, aligned(4)));
+
+#define OP_BITS 0x0000FF00
+#define ID_BITS 0x000000FF
+
+/*
+ * brief the data structure of PORT Control Command
+ * use to control port properties (64 bytes)
+ */
+
+struct port_ctl_req {
+ __le32 tag;
+ __le32 portop_portid;
+ __le32 param0;
+ __le32 param1;
+ u32 reserved1[27];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of HW Event Ack Command
+ * use to acknowledge receive HW event (64 bytes)
+ */
+struct hw_event_ack_req {
+ __le32 tag;
+ __le32 phyid_sea_portid;
+ __le32 param0;
+ __le32 param1;
+ u32 reserved1[27];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of PHY_START Response Command
+ * indicates the completion of PHY_START command (64 bytes)
+ */
+struct phy_start_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 phyid;
+ u32 reserved[12];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of PHY_STOP Response Command
+ * indicates the completion of PHY_STOP command (64 bytes)
+ */
+struct phy_stop_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 phyid;
+ u32 reserved[12];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of SSP Completion Response
+ * use to indicate a SSP Completion (n bytes)
+ */
+struct ssp_completion_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 param;
+ __le32 ssptag_rescv_rescpad;
+ struct ssp_response_iu ssp_resp_iu;
+ __le32 residual_count;
+} __attribute__((packed, aligned(4)));
+
+#define SSP_RESCV_BIT 0x00010000
+
+/*
+ * brief the data structure of SATA EVNET response
+ * use to indicate a SATA Completion (64 bytes)
+ */
+struct sata_event_resp {
+ __le32 tag;
+ __le32 event;
+ __le32 port_id;
+ __le32 device_id;
+ u32 reserved;
+ __le32 event_param0;
+ __le32 event_param1;
+ __le32 sata_addr_h32;
+ __le32 sata_addr_l32;
+ __le32 e_udt1_udt0_crc;
+ __le32 e_udt5_udt4_udt3_udt2;
+ __le32 a_udt1_udt0_crc;
+ __le32 a_udt5_udt4_udt3_udt2;
+ __le32 hwdevid_diferr;
+ __le32 err_framelen_byteoffset;
+ __le32 err_dataframe;
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of SSP EVNET esponse
+ * use to indicate a SSP Completion (64 bytes)
+ */
+struct ssp_event_resp {
+ __le32 tag;
+ __le32 event;
+ __le32 port_id;
+ __le32 device_id;
+ __le32 ssp_tag;
+ __le32 event_param0;
+ __le32 event_param1;
+ __le32 sas_addr_h32;
+ __le32 sas_addr_l32;
+ __le32 e_udt1_udt0_crc;
+ __le32 e_udt5_udt4_udt3_udt2;
+ __le32 a_udt1_udt0_crc;
+ __le32 a_udt5_udt4_udt3_udt2;
+ __le32 hwdevid_diferr;
+ __le32 err_framelen_byteoffset;
+ __le32 err_dataframe;
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of General Event Notification Response
+ * use to describe MPI General Event Notification Response (64 bytes)
+ */
+struct general_event_resp {
+ __le32 status;
+ __le32 inb_IOMB_payload[14];
+} __attribute__((packed, aligned(4)));
+
+#define GENERAL_EVENT_PAYLOAD 14
+#define OPCODE_BITS 0x00000fff
+
+/*
+ * brief the data structure of SMP Request Command
+ * use to describe MPI SMP REQUEST Command (64 bytes)
+ */
+struct smp_req {
+ __le32 tag;
+ __le32 device_id;
+ __le32 len_ip_ir;
+ /* Bits [0] - Indirect response */
+ /* Bits [1] - Indirect Payload */
+ /* Bits [15:2] - Reserved */
+ /* Bits [23:16] - direct payload Len */
+ /* Bits [31:24] - Reserved */
+ u8 smp_req16[16];
+ union {
+ u8 smp_req[32];
+ struct {
+ __le64 long_req_addr;/* sg dma address, LE */
+ __le32 long_req_size;/* LE */
+ u32 _r_a;
+ __le64 long_resp_addr;/* sg dma address, LE */
+ __le32 long_resp_size;/* LE */
+ u32 _r_b;
+ } long_smp_req;/* sequencer extension */
+ };
+ __le32 rsvd[16];
+} __attribute__((packed, aligned(4)));
+/*
+ * brief the data structure of SMP Completion Response
+ * use to describe MPI SMP Completion Response (64 bytes)
+ */
+struct smp_completion_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 param;
+ u8 _r_a[252];
+} __attribute__((packed, aligned(4)));
+
+/*
+ *brief the data structure of SSP SMP SATA Abort Command
+ * use to describe MPI SSP SMP & SATA Abort Command (64 bytes)
+ */
+struct task_abort_req {
+ __le32 tag;
+ __le32 device_id;
+ __le32 tag_to_abort;
+ __le32 abort_all;
+ u32 reserved[27];
+} __attribute__((packed, aligned(4)));
+
+/* These flags used for SSP SMP & SATA Abort */
+#define ABORT_MASK 0x3
+#define ABORT_SINGLE 0x0
+#define ABORT_ALL 0x1
+
+/**
+ * brief the data structure of SSP SATA SMP Abort Response
+ * use to describe SSP SMP & SATA Abort Response ( 64 bytes)
+ */
+struct task_abort_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 scp;
+ u32 reserved[12];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SAS Diagnostic Start/End Command
+ * use to describe MPI SAS Diagnostic Start/End Command (64 bytes)
+ */
+struct sas_diag_start_end_req {
+ __le32 tag;
+ __le32 operation_phyid;
+ u32 reserved[29];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SAS Diagnostic Execute Command
+ * use to describe MPI SAS Diagnostic Execute Command (64 bytes)
+ */
+struct sas_diag_execute_req {
+ __le32 tag;
+ __le32 cmdtype_cmddesc_phyid;
+ __le32 pat1_pat2;
+ __le32 threshold;
+ __le32 codepat_errmsk;
+ __le32 pmon;
+ __le32 pERF1CTL;
+ u32 reserved[24];
+} __attribute__((packed, aligned(4)));
+
+#define SAS_DIAG_PARAM_BYTES 24
+
+/*
+ * brief the data structure of Set Device State Command
+ * use to describe MPI Set Device State Command (64 bytes)
+ */
+struct set_dev_state_req {
+ __le32 tag;
+ __le32 device_id;
+ __le32 nds;
+ u32 reserved[28];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of SATA Start Command
+ * use to describe MPI SATA IO Start Command (64 bytes)
+ * Note: This structure is common for normal / encryption I/O
+ */
+
+struct sata_start_req {
+ __le32 tag;
+ __le32 device_id;
+ __le32 data_len;
+ __le32 ncqtag_atap_dir_m_dad;
+ struct host_to_dev_fis sata_fis;
+ u32 reserved1;
+ u32 reserved2; /* dword 11. rsvd for normal I/O. */
+ /* EPLE Descl for enc I/O */
+ u32 addr_low; /* dword 12. rsvd for enc I/O */
+ u32 addr_high; /* dword 13. reserved for enc I/O */
+ __le32 len; /* dword 14: length for normal I/O. */
+ /* EPLE Desch for enc I/O */
+ __le32 esgl; /* dword 15. rsvd for enc I/O */
+ __le32 atapi_scsi_cdb[4]; /* dword 16-19. rsvd for enc I/O */
+ /* The below fields are reserved for normal I/O */
+ __le32 key_index_mode; /* dword 20 */
+ __le32 sector_cnt_enss;/* dword 21 */
+ __le32 keytagl; /* dword 22 */
+ __le32 keytagh; /* dword 23 */
+ __le32 twk_val0; /* dword 24 */
+ __le32 twk_val1; /* dword 25 */
+ __le32 twk_val2; /* dword 26 */
+ __le32 twk_val3; /* dword 27 */
+ __le32 enc_addr_low; /* dword 28. Encryption SGL address high */
+ __le32 enc_addr_high; /* dword 29. Encryption SGL address low */
+ __le32 enc_len; /* dword 30. Encryption length */
+ __le32 enc_esgl; /* dword 31. Encryption esgl bit */
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SSP INI TM Start Command
+ * use to describe MPI SSP INI TM Start Command (64 bytes)
+ */
+struct ssp_ini_tm_start_req {
+ __le32 tag;
+ __le32 device_id;
+ __le32 relate_tag;
+ __le32 tmf;
+ u8 lun[8];
+ __le32 ds_ads_m;
+ u32 reserved[24];
+} __attribute__((packed, aligned(4)));
+
+struct ssp_info_unit {
+ u8 lun[8];/* SCSI Logical Unit Number */
+ u8 reserved1;/* reserved */
+ u8 efb_prio_attr;
+ /* B7 : enabledFirstBurst */
+ /* B6-3 : taskPriority */
+ /* B2-0 : taskAttribute */
+ u8 reserved2; /* reserved */
+ u8 additional_cdb_len;
+ /* B7-2 : additional_cdb_len */
+ /* B1-0 : reserved */
+ u8 cdb[16];/* The SCSI CDB up to 16 bytes length */
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SSP INI IO Start Command
+ * use to describe MPI SSP INI IO Start Command (64 bytes)
+ * Note: This structure is common for normal / encryption I/O
+ */
+struct ssp_ini_io_start_req {
+ __le32 tag;
+ __le32 device_id;
+ __le32 data_len;
+ __le32 dad_dir_m_tlr;
+ struct ssp_info_unit ssp_iu;
+ __le32 addr_low; /* dword 12: sgl low for normal I/O. */
+ /* epl_descl for encryption I/O */
+ __le32 addr_high; /* dword 13: sgl hi for normal I/O */
+ /* dpl_descl for encryption I/O */
+ __le32 len; /* dword 14: len for normal I/O. */
+ /* edpl_desch for encryption I/O */
+ __le32 esgl; /* dword 15: ESGL bit for normal I/O. */
+ /* user defined tag mask for enc I/O */
+ /* The below fields are reserved for normal I/O */
+ u8 udt[12]; /* dword 16-18 */
+ __le32 sectcnt_ios; /* dword 19 */
+ __le32 key_cmode; /* dword 20 */
+ __le32 ks_enss; /* dword 21 */
+ __le32 keytagl; /* dword 22 */
+ __le32 keytagh; /* dword 23 */
+ __le32 twk_val0; /* dword 24 */
+ __le32 twk_val1; /* dword 25 */
+ __le32 twk_val2; /* dword 26 */
+ __le32 twk_val3; /* dword 27 */
+ __le32 enc_addr_low; /* dword 28: Encryption sgl addr low */
+ __le32 enc_addr_high; /* dword 29: Encryption sgl addr hi */
+ __le32 enc_len; /* dword 30: Encryption length */
+ __le32 enc_esgl; /* dword 31: ESGL bit for encryption */
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for SSP_INI_DIF_ENC_IO COMMAND
+ * use to initiate SSP I/O operation with optional DIF/ENC
+ */
+struct ssp_dif_enc_io_req {
+ __le32 tag;
+ __le32 device_id;
+ __le32 data_len;
+ __le32 dirMTlr;
+ __le32 sspiu0;
+ __le32 sspiu1;
+ __le32 sspiu2;
+ __le32 sspiu3;
+ __le32 sspiu4;
+ __le32 sspiu5;
+ __le32 sspiu6;
+ __le32 epl_des;
+ __le32 dpl_desl_ndplr;
+ __le32 dpl_desh;
+ __le32 uum_uuv_bss_difbits;
+ u8 udt[12];
+ __le32 sectcnt_ios;
+ __le32 key_cmode;
+ __le32 ks_enss;
+ __le32 keytagl;
+ __le32 keytagh;
+ __le32 twk_val0;
+ __le32 twk_val1;
+ __le32 twk_val2;
+ __le32 twk_val3;
+ __le32 addr_low;
+ __le32 addr_high;
+ __le32 len;
+ __le32 esgl;
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of Firmware download
+ * use to describe MPI FW DOWNLOAD Command (64 bytes)
+ */
+struct fw_flash_Update_req {
+ __le32 tag;
+ __le32 cur_image_offset;
+ __le32 cur_image_len;
+ __le32 total_image_len;
+ u32 reserved0[7];
+ __le32 sgl_addr_lo;
+ __le32 sgl_addr_hi;
+ __le32 len;
+ __le32 ext_reserved;
+ u32 reserved1[16];
+} __attribute__((packed, aligned(4)));
+
+#define FWFLASH_IOMB_RESERVED_LEN 0x07
+/**
+ * brief the data structure of FW_FLASH_UPDATE Response
+ * use to describe MPI FW_FLASH_UPDATE Response (64 bytes)
+ *
+ */
+ struct fw_flash_Update_resp {
+ __le32 tag;
+ __le32 status;
+ u32 reserved[13];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of Get NVM Data Command
+ * use to get data from NVM in HBA(64 bytes)
+ */
+struct get_nvm_data_req {
+ __le32 tag;
+ __le32 len_ir_vpdd;
+ __le32 vpd_offset;
+ u32 reserved[8];
+ __le32 resp_addr_lo;
+ __le32 resp_addr_hi;
+ __le32 resp_len;
+ u32 reserved1[17];
+} __attribute__((packed, aligned(4)));
+
+struct set_nvm_data_req {
+ __le32 tag;
+ __le32 len_ir_vpdd;
+ __le32 vpd_offset;
+ u32 reserved[8];
+ __le32 resp_addr_lo;
+ __le32 resp_addr_hi;
+ __le32 resp_len;
+ u32 reserved1[17];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for SET CONTROLLER CONFIG COMMAND
+ * use to modify controller configuration
+ */
+struct set_ctrl_cfg_req {
+ __le32 tag;
+ __le32 cfg_pg[14];
+ u32 reserved[16];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for GET CONTROLLER CONFIG COMMAND
+ * use to get controller configuration page
+ */
+struct get_ctrl_cfg_req {
+ __le32 tag;
+ __le32 pgcd;
+ __le32 int_vec;
+ u32 reserved[28];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for KEK_MANAGEMENT COMMAND
+ * use for KEK management
+ */
+struct kek_mgmt_req {
+ __le32 tag;
+ __le32 new_curidx_ksop;
+ u32 reserved;
+ __le32 kblob[12];
+ u32 reserved1[16];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for DEK_MANAGEMENT COMMAND
+ * use for DEK management
+ */
+struct dek_mgmt_req {
+ __le32 tag;
+ __le32 kidx_dsop;
+ __le32 dekidx;
+ __le32 addr_l;
+ __le32 addr_h;
+ __le32 nent;
+ __le32 dbf_tblsize;
+ u32 reserved[24];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for SET PHY PROFILE COMMAND
+ * use to retrive phy specific information
+ */
+struct set_phy_profile_req {
+ __le32 tag;
+ __le32 ppc_phyid;
+ u32 reserved[29];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for GET PHY PROFILE COMMAND
+ * use to retrive phy specific information
+ */
+struct get_phy_profile_req {
+ __le32 tag;
+ __le32 ppc_phyid;
+ __le32 profile[29];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for EXT FLASH PARTITION
+ * use to manage ext flash partition
+ */
+struct ext_flash_partition_req {
+ __le32 tag;
+ __le32 cmd;
+ __le32 offset;
+ __le32 len;
+ u32 reserved[7];
+ __le32 addr_low;
+ __le32 addr_high;
+ __le32 len1;
+ __le32 ext;
+ u32 reserved1[16];
+} __attribute__((packed, aligned(4)));
+
+#define TWI_DEVICE 0x0
+#define C_SEEPROM 0x1
+#define VPD_FLASH 0x4
+#define AAP1_RDUMP 0x5
+#define IOP_RDUMP 0x6
+#define EXPAN_ROM 0x7
+
+#define IPMode 0x80000000
+#define NVMD_TYPE 0x0000000F
+#define NVMD_STAT 0x0000FFFF
+#define NVMD_LEN 0xFF000000
+/**
+ * brief the data structure of Get NVMD Data Response
+ * use to describe MPI Get NVMD Data Response (64 bytes)
+ */
+struct get_nvm_data_resp {
+ __le32 tag;
+ __le32 ir_tda_bn_dps_das_nvm;
+ __le32 dlen_status;
+ __le32 nvm_data[12];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SAS Diagnostic Start/End Response
+ * use to describe MPI SAS Diagnostic Start/End Response (64 bytes)
+ *
+ */
+struct sas_diag_start_end_resp {
+ __le32 tag;
+ __le32 status;
+ u32 reserved[13];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SAS Diagnostic Execute Response
+ * use to describe MPI SAS Diagnostic Execute Response (64 bytes)
+ *
+ */
+struct sas_diag_execute_resp {
+ __le32 tag;
+ __le32 cmdtype_cmddesc_phyid;
+ __le32 Status;
+ __le32 ReportData;
+ u32 reserved[11];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of Set Device State Response
+ * use to describe MPI Set Device State Response (64 bytes)
+ *
+ */
+struct set_dev_state_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 device_id;
+ __le32 pds_nds;
+ u32 reserved[11];
+} __attribute__((packed, aligned(4)));
+
+/* new outbound structure for spcv - begins */
+/**
+ * brief the data structure for SET CONTROLLER CONFIG COMMAND
+ * use to modify controller configuration
+ */
+struct set_ctrl_cfg_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 err_qlfr_pgcd;
+ u32 reserved[12];
+} __attribute__((packed, aligned(4)));
+
+struct get_ctrl_cfg_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 err_qlfr;
+ __le32 confg_page[12];
+} __attribute__((packed, aligned(4)));
+
+struct kek_mgmt_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 kidx_new_curr_ksop;
+ __le32 err_qlfr;
+ u32 reserved[11];
+} __attribute__((packed, aligned(4)));
+
+struct dek_mgmt_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 kekidx_tbls_dsop;
+ __le32 dekidx;
+ __le32 err_qlfr;
+ u32 reserved[10];
+} __attribute__((packed, aligned(4)));
+
+struct get_phy_profile_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 ppc_phyid;
+ __le32 ppc_specific_rsp[12];
+} __attribute__((packed, aligned(4)));
+
+struct flash_op_ext_resp {
+ __le32 tag;
+ __le32 cmd;
+ __le32 status;
+ __le32 epart_size;
+ __le32 epart_sect_size;
+ u32 reserved[10];
+} __attribute__((packed, aligned(4)));
+
+struct set_phy_profile_resp {
+ __le32 tag;
+ __le32 status;
+ __le32 ppc_phyid;
+ __le32 ppc_specific_rsp[12];
+} __attribute__((packed, aligned(4)));
+
+struct ssp_coalesced_comp_resp {
+ __le32 coal_cnt;
+ __le32 tag0;
+ __le32 ssp_tag0;
+ __le32 tag1;
+ __le32 ssp_tag1;
+ __le32 add_tag_ssp_tag[10];
+} __attribute__((packed, aligned(4)));
+
+/* new outbound structure for spcv - ends */
+
+/* brief data structure for SAS protocol timer configuration page.
+ *
+ */
+struct SASProtocolTimerConfig {
+ __le32 pageCode; /* 0 */
+ __le32 MST_MSI; /* 1 */
+ __le32 STP_SSP_MCT_TMO; /* 2 */
+ __le32 STP_FRM_TMO; /* 3 */
+ __le32 STP_IDLE_TMO; /* 4 */
+ __le32 OPNRJT_RTRY_INTVL; /* 5 */
+ __le32 Data_Cmd_OPNRJT_RTRY_TMO; /* 6 */
+ __le32 Data_Cmd_OPNRJT_RTRY_THR; /* 7 */
+ __le32 MAX_AIP; /* 8 */
+} __attribute__((packed, aligned(4)));
+
+typedef struct SASProtocolTimerConfig SASProtocolTimerConfig_t;
+
+#define NDS_BITS 0x0F
+#define PDS_BITS 0xF0
+
+/*
+ * HW Events type
+ */
+
+#define HW_EVENT_RESET_START 0x01
+#define HW_EVENT_CHIP_RESET_COMPLETE 0x02
+#define HW_EVENT_PHY_STOP_STATUS 0x03
+#define HW_EVENT_SAS_PHY_UP 0x04
+#define HW_EVENT_SATA_PHY_UP 0x05
+#define HW_EVENT_SATA_SPINUP_HOLD 0x06
+#define HW_EVENT_PHY_DOWN 0x07
+#define HW_EVENT_PORT_INVALID 0x08
+#define HW_EVENT_BROADCAST_CHANGE 0x09
+#define HW_EVENT_PHY_ERROR 0x0A
+#define HW_EVENT_BROADCAST_SES 0x0B
+#define HW_EVENT_INBOUND_CRC_ERROR 0x0C
+#define HW_EVENT_HARD_RESET_RECEIVED 0x0D
+#define HW_EVENT_MALFUNCTION 0x0E
+#define HW_EVENT_ID_FRAME_TIMEOUT 0x0F
+#define HW_EVENT_BROADCAST_EXP 0x10
+#define HW_EVENT_PHY_START_STATUS 0x11
+#define HW_EVENT_LINK_ERR_INVALID_DWORD 0x12
+#define HW_EVENT_LINK_ERR_DISPARITY_ERROR 0x13
+#define HW_EVENT_LINK_ERR_CODE_VIOLATION 0x14
+#define HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH 0x15
+#define HW_EVENT_LINK_ERR_PHY_RESET_FAILED 0x16
+#define HW_EVENT_PORT_RECOVERY_TIMER_TMO 0x17
+#define HW_EVENT_PORT_RECOVER 0x18
+#define HW_EVENT_PORT_RESET_TIMER_TMO 0x19
+#define HW_EVENT_PORT_RESET_COMPLETE 0x20
+#define EVENT_BROADCAST_ASYNCH_EVENT 0x21
+
+/* port state */
+#define PORT_NOT_ESTABLISHED 0x00
+#define PORT_VALID 0x01
+#define PORT_LOSTCOMM 0x02
+#define PORT_IN_RESET 0x04
+#define PORT_3RD_PARTY_RESET 0x07
+#define PORT_INVALID 0x08
+
+/*
+ * SSP/SMP/SATA IO Completion Status values
+ */
+
+#define IO_SUCCESS 0x00
+#define IO_ABORTED 0x01
+#define IO_OVERFLOW 0x02
+#define IO_UNDERFLOW 0x03
+#define IO_FAILED 0x04
+#define IO_ABORT_RESET 0x05
+#define IO_NOT_VALID 0x06
+#define IO_NO_DEVICE 0x07
+#define IO_ILLEGAL_PARAMETER 0x08
+#define IO_LINK_FAILURE 0x09
+#define IO_PROG_ERROR 0x0A
+
+#define IO_EDC_IN_ERROR 0x0B
+#define IO_EDC_OUT_ERROR 0x0C
+#define IO_ERROR_HW_TIMEOUT 0x0D
+#define IO_XFER_ERROR_BREAK 0x0E
+#define IO_XFER_ERROR_PHY_NOT_READY 0x0F
+#define IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED 0x10
+#define IO_OPEN_CNX_ERROR_ZONE_VIOLATION 0x11
+#define IO_OPEN_CNX_ERROR_BREAK 0x12
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS 0x13
+#define IO_OPEN_CNX_ERROR_BAD_DESTINATION 0x14
+#define IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED 0x15
+#define IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY 0x16
+#define IO_OPEN_CNX_ERROR_WRONG_DESTINATION 0x17
+/* This error code 0x18 is not used on SPCv */
+#define IO_OPEN_CNX_ERROR_UNKNOWN_ERROR 0x18
+#define IO_XFER_ERROR_NAK_RECEIVED 0x19
+#define IO_XFER_ERROR_ACK_NAK_TIMEOUT 0x1A
+#define IO_XFER_ERROR_PEER_ABORTED 0x1B
+#define IO_XFER_ERROR_RX_FRAME 0x1C
+#define IO_XFER_ERROR_DMA 0x1D
+#define IO_XFER_ERROR_CREDIT_TIMEOUT 0x1E
+#define IO_XFER_ERROR_SATA_LINK_TIMEOUT 0x1F
+#define IO_XFER_ERROR_SATA 0x20
+
+/* This error code 0x22 is not used on SPCv */
+#define IO_XFER_ERROR_ABORTED_DUE_TO_SRST 0x22
+#define IO_XFER_ERROR_REJECTED_NCQ_MODE 0x21
+#define IO_XFER_ERROR_ABORTED_NCQ_MODE 0x23
+#define IO_XFER_OPEN_RETRY_TIMEOUT 0x24
+/* This error code 0x25 is not used on SPCv */
+#define IO_XFER_SMP_RESP_CONNECTION_ERROR 0x25
+#define IO_XFER_ERROR_UNEXPECTED_PHASE 0x26
+#define IO_XFER_ERROR_XFER_RDY_OVERRUN 0x27
+#define IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED 0x28
+#define IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT 0x30
+
+/* The following error code 0x31 and 0x32 are not using (obsolete) */
+#define IO_XFER_ERROR_CMD_ISSUE_BREAK_BEFORE_ACK_NAK 0x31
+#define IO_XFER_ERROR_CMD_ISSUE_PHY_DOWN_BEFORE_ACK_NAK 0x32
+
+#define IO_XFER_ERROR_OFFSET_MISMATCH 0x34
+#define IO_XFER_ERROR_XFER_ZERO_DATA_LEN 0x35
+#define IO_XFER_CMD_FRAME_ISSUED 0x36
+#define IO_ERROR_INTERNAL_SMP_RESOURCE 0x37
+#define IO_PORT_IN_RESET 0x38
+#define IO_DS_NON_OPERATIONAL 0x39
+#define IO_DS_IN_RECOVERY 0x3A
+#define IO_TM_TAG_NOT_FOUND 0x3B
+#define IO_XFER_PIO_SETUP_ERROR 0x3C
+#define IO_SSP_EXT_IU_ZERO_LEN_ERROR 0x3D
+#define IO_DS_IN_ERROR 0x3E
+#define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY 0x3F
+#define IO_ABORT_IN_PROGRESS 0x40
+#define IO_ABORT_DELAYED 0x41
+#define IO_INVALID_LENGTH 0x42
+
+/********** additional response event values *****************/
+
+#define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY_ALT 0x43
+#define IO_XFER_OPEN_RETRY_BACKOFF_THRESHOLD_REACHED 0x44
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_TMO 0x45
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_NO_DEST 0x46
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_COLLIDE 0x47
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_PATHWAY_BLOCKED 0x48
+#define IO_DS_INVALID 0x49
+/* WARNING: the value is not contiguous from here */
+#define IO_XFER_ERR_LAST_PIO_DATAIN_CRC_ERR 0x52
+#define IO_XFER_DMA_ACTIVATE_TIMEOUT 0x53
+#define IO_XFER_ERROR_INTERNAL_CRC_ERROR 0x54
+#define MPI_IO_RQE_BUSY_FULL 0x55
+#define IO_XFER_ERR_EOB_DATA_OVERRUN 0x56
+#define IO_XFR_ERROR_INVALID_SSP_RSP_FRAME 0x57
+#define IO_OPEN_CNX_ERROR_OPEN_PREEMPTED 0x58
+
+#define MPI_ERR_IO_RESOURCE_UNAVAILABLE 0x1004
+#define MPI_ERR_ATAPI_DEVICE_BUSY 0x1024
+
+#define IO_XFR_ERROR_DEK_KEY_CACHE_MISS 0x2040
+/*
+ * An encryption IO request failed due to DEK Key Tag mismatch.
+ * The key tag supplied in the encryption IOMB does not match with
+ * the Key Tag in the referenced DEK Entry.
+ */
+#define IO_XFR_ERROR_DEK_KEY_TAG_MISMATCH 0x2041
+#define IO_XFR_ERROR_CIPHER_MODE_INVALID 0x2042
+/*
+ * An encryption I/O request failed because the initial value (IV)
+ * in the unwrapped DEK blob didn't match the IV used to unwrap it.
+ */
+#define IO_XFR_ERROR_DEK_IV_MISMATCH 0x2043
+/* An encryption I/O request failed due to an internal RAM ECC or
+ * interface error while unwrapping the DEK. */
+#define IO_XFR_ERROR_DEK_RAM_INTERFACE_ERROR 0x2044
+/* An encryption I/O request failed due to an internal RAM ECC or
+ * interface error while unwrapping the DEK. */
+#define IO_XFR_ERROR_INTERNAL_RAM 0x2045
+/*
+ * An encryption I/O request failed
+ * because the DEK index specified in the I/O was outside the bounds of
+ * the total number of entries in the host DEK table.
+ */
+#define IO_XFR_ERROR_DEK_INDEX_OUT_OF_BOUNDS0x2046
+
+/* define DIF IO response error status code */
+#define IO_XFR_ERROR_DIF_MISMATCH 0x3000
+#define IO_XFR_ERROR_DIF_APPLICATION_TAG_MISMATCH 0x3001
+#define IO_XFR_ERROR_DIF_REFERENCE_TAG_MISMATCH 0x3002
+#define IO_XFR_ERROR_DIF_CRC_MISMATCH 0x3003
+
+/* define operator management response status and error qualifier code */
+#define OPR_MGMT_OP_NOT_SUPPORTED 0x2060
+#define OPR_MGMT_MPI_ENC_ERR_OPR_PARAM_ILLEGAL 0x2061
+#define OPR_MGMT_MPI_ENC_ERR_OPR_ID_NOT_FOUND 0x2062
+#define OPR_MGMT_MPI_ENC_ERR_OPR_ROLE_NOT_MATCH 0x2063
+#define OPR_MGMT_MPI_ENC_ERR_OPR_MAX_NUM_EXCEEDED 0x2064
+#define OPR_MGMT_MPI_ENC_ERR_KEK_UNWRAP_FAIL 0x2022
+#define OPR_MGMT_MPI_ENC_ERR_NVRAM_OPERATION_FAILURE 0x2023
+/***************** additional response event values ***************/
+
+/* WARNING: This error code must always be the last number.
+ * If you add error code, modify this code also
+ * It is used as an index
+ */
+#define IO_ERROR_UNKNOWN_GENERIC 0x2023
+
+/* MSGU CONFIGURATION TABLE*/
+
+#define SPCv_MSGU_CFG_TABLE_UPDATE 0x001
+#define SPCv_MSGU_CFG_TABLE_RESET 0x002
+#define SPCv_MSGU_CFG_TABLE_FREEZE 0x004
+#define SPCv_MSGU_CFG_TABLE_UNFREEZE 0x008
+#define MSGU_IBDB_SET 0x00
+#define MSGU_HOST_INT_STATUS 0x08
+#define MSGU_HOST_INT_MASK 0x0C
+#define MSGU_IOPIB_INT_STATUS 0x18
+#define MSGU_IOPIB_INT_MASK 0x1C
+#define MSGU_IBDB_CLEAR 0x20
+
+#define MSGU_MSGU_CONTROL 0x24
+#define MSGU_ODR 0x20
+#define MSGU_ODCR 0x28
+
+#define MSGU_ODMR 0x30
+#define MSGU_ODMR_U 0x34
+#define MSGU_ODMR_CLR 0x38
+#define MSGU_ODMR_CLR_U 0x3C
+#define MSGU_OD_RSVD 0x40
+
+#define MSGU_SCRATCH_PAD_0 0x44
+#define MSGU_SCRATCH_PAD_1 0x48
+#define MSGU_SCRATCH_PAD_2 0x4C
+#define MSGU_SCRATCH_PAD_3 0x50
+#define MSGU_HOST_SCRATCH_PAD_0 0x54
+#define MSGU_HOST_SCRATCH_PAD_1 0x58
+#define MSGU_HOST_SCRATCH_PAD_2 0x5C
+#define MSGU_HOST_SCRATCH_PAD_3 0x60
+#define MSGU_HOST_SCRATCH_PAD_4 0x64
+#define MSGU_HOST_SCRATCH_PAD_5 0x68
+#define MSGU_HOST_SCRATCH_PAD_6 0x6C
+#define MSGU_HOST_SCRATCH_PAD_7 0x70
+
+/* bit definition for ODMR register */
+#define ODMR_MASK_ALL 0xFFFFFFFF/* mask all
+ interrupt vector */
+#define ODMR_CLEAR_ALL 0 /* clear all
+ interrupt vector */
+/* bit definition for ODCR register */
+#define ODCR_CLEAR_ALL 0xFFFFFFFF /* mask all
+ interrupt vector*/
+/* MSIX Interupts */
+#define MSIX_TABLE_OFFSET 0x2000
+#define MSIX_TABLE_ELEMENT_SIZE 0x10
+#define MSIX_INTERRUPT_CONTROL_OFFSET 0xC
+#define MSIX_TABLE_BASE (MSIX_TABLE_OFFSET + \
+ MSIX_INTERRUPT_CONTROL_OFFSET)
+#define MSIX_INTERRUPT_DISABLE 0x1
+#define MSIX_INTERRUPT_ENABLE 0x0
+
+/* state definition for Scratch Pad1 register */
+#define SCRATCH_PAD_RAAE_READY 0x3
+#define SCRATCH_PAD_ILA_READY 0xC
+#define SCRATCH_PAD_BOOT_LOAD_SUCCESS 0x0
+#define SCRATCH_PAD_IOP0_READY 0xC00
+#define SCRATCH_PAD_IOP1_READY 0x3000
+
+/* boot loader state */
+#define SCRATCH_PAD1_BOOTSTATE_MASK 0x70 /* Bit 4-6 */
+#define SCRATCH_PAD1_BOOTSTATE_SUCESS 0x0 /* Load successful */
+#define SCRATCH_PAD1_BOOTSTATE_HDA_SEEPROM 0x10 /* HDA SEEPROM */
+#define SCRATCH_PAD1_BOOTSTATE_HDA_BOOTSTRAP 0x20 /* HDA BootStrap Pins */
+#define SCRATCH_PAD1_BOOTSTATE_HDA_SOFTRESET 0x30 /* HDA Soft Reset */
+#define SCRATCH_PAD1_BOOTSTATE_CRIT_ERROR 0x40 /* HDA critical error */
+#define SCRATCH_PAD1_BOOTSTATE_R1 0x50 /* Reserved */
+#define SCRATCH_PAD1_BOOTSTATE_R2 0x60 /* Reserved */
+#define SCRATCH_PAD1_BOOTSTATE_FATAL 0x70 /* Fatal Error */
+
+ /* state definition for Scratch Pad2 register */
+#define SCRATCH_PAD2_POR 0x00 /* power on state */
+#define SCRATCH_PAD2_SFR 0x01 /* soft reset state */
+#define SCRATCH_PAD2_ERR 0x02 /* error state */
+#define SCRATCH_PAD2_RDY 0x03 /* ready state */
+#define SCRATCH_PAD2_FWRDY_RST 0x04 /* FW rdy for soft reset flag */
+#define SCRATCH_PAD2_IOPRDY_RST 0x08 /* IOP ready for soft reset */
+#define SCRATCH_PAD2_STATE_MASK 0xFFFFFFF4 /* ScratchPad 2
+ Mask, bit1-0 State */
+#define SCRATCH_PAD2_RESERVED 0x000003FC/* Scratch Pad1
+ Reserved bit 2 to 9 */
+
+#define SCRATCH_PAD_ERROR_MASK 0xFFFFFC00 /* Error mask bits */
+#define SCRATCH_PAD_STATE_MASK 0x00000003 /* State Mask bits */
+
+/* main configuration offset - byte offset */
+#define MAIN_SIGNATURE_OFFSET 0x00 /* DWORD 0x00 */
+#define MAIN_INTERFACE_REVISION 0x04 /* DWORD 0x01 */
+#define MAIN_FW_REVISION 0x08 /* DWORD 0x02 */
+#define MAIN_MAX_OUTSTANDING_IO_OFFSET 0x0C /* DWORD 0x03 */
+#define MAIN_MAX_SGL_OFFSET 0x10 /* DWORD 0x04 */
+#define MAIN_CNTRL_CAP_OFFSET 0x14 /* DWORD 0x05 */
+#define MAIN_GST_OFFSET 0x18 /* DWORD 0x06 */
+#define MAIN_IBQ_OFFSET 0x1C /* DWORD 0x07 */
+#define MAIN_OBQ_OFFSET 0x20 /* DWORD 0x08 */
+#define MAIN_IQNPPD_HPPD_OFFSET 0x24 /* DWORD 0x09 */
+
+/* 0x28 - 0x4C - RSVD */
+#define MAIN_EVENT_CRC_CHECK 0x48 /* DWORD 0x12 */
+#define MAIN_EVENT_LOG_ADDR_HI 0x50 /* DWORD 0x14 */
+#define MAIN_EVENT_LOG_ADDR_LO 0x54 /* DWORD 0x15 */
+#define MAIN_EVENT_LOG_BUFF_SIZE 0x58 /* DWORD 0x16 */
+#define MAIN_EVENT_LOG_OPTION 0x5C /* DWORD 0x17 */
+#define MAIN_PCS_EVENT_LOG_ADDR_HI 0x60 /* DWORD 0x18 */
+#define MAIN_PCS_EVENT_LOG_ADDR_LO 0x64 /* DWORD 0x19 */
+#define MAIN_PCS_EVENT_LOG_BUFF_SIZE 0x68 /* DWORD 0x1A */
+#define MAIN_PCS_EVENT_LOG_OPTION 0x6C /* DWORD 0x1B */
+#define MAIN_FATAL_ERROR_INTERRUPT 0x70 /* DWORD 0x1C */
+#define MAIN_FATAL_ERROR_RDUMP0_OFFSET 0x74 /* DWORD 0x1D */
+#define MAIN_FATAL_ERROR_RDUMP0_LENGTH 0x78 /* DWORD 0x1E */
+#define MAIN_FATAL_ERROR_RDUMP1_OFFSET 0x7C /* DWORD 0x1F */
+#define MAIN_FATAL_ERROR_RDUMP1_LENGTH 0x80 /* DWORD 0x20 */
+#define MAIN_GPIO_LED_FLAGS_OFFSET 0x84 /* DWORD 0x21 */
+#define MAIN_ANALOG_SETUP_OFFSET 0x88 /* DWORD 0x22 */
+
+#define MAIN_INT_VECTOR_TABLE_OFFSET 0x8C /* DWORD 0x23 */
+#define MAIN_SAS_PHY_ATTR_TABLE_OFFSET 0x90 /* DWORD 0x24 */
+#define MAIN_PORT_RECOVERY_TIMER 0x94 /* DWORD 0x25 */
+#define MAIN_INT_REASSERTION_DELAY 0x98 /* DWORD 0x26 */
+
+/* Gereral Status Table offset - byte offset */
+#define GST_GSTLEN_MPIS_OFFSET 0x00
+#define GST_IQ_FREEZE_STATE0_OFFSET 0x04
+#define GST_IQ_FREEZE_STATE1_OFFSET 0x08
+#define GST_MSGUTCNT_OFFSET 0x0C
+#define GST_IOPTCNT_OFFSET 0x10
+/* 0x14 - 0x34 - RSVD */
+#define GST_GPIO_INPUT_VAL 0x38
+/* 0x3c - 0x40 - RSVD */
+#define GST_RERRINFO_OFFSET0 0x44
+#define GST_RERRINFO_OFFSET1 0x48
+#define GST_RERRINFO_OFFSET2 0x4c
+#define GST_RERRINFO_OFFSET3 0x50
+#define GST_RERRINFO_OFFSET4 0x54
+#define GST_RERRINFO_OFFSET5 0x58
+#define GST_RERRINFO_OFFSET6 0x5c
+#define GST_RERRINFO_OFFSET7 0x60
+
+/* General Status Table - MPI state */
+#define GST_MPI_STATE_UNINIT 0x00
+#define GST_MPI_STATE_INIT 0x01
+#define GST_MPI_STATE_TERMINATION 0x02
+#define GST_MPI_STATE_ERROR 0x03
+#define GST_MPI_STATE_MASK 0x07
+
+/* Per SAS PHY Attributes */
+
+#define PSPA_PHYSTATE0_OFFSET 0x00 /* Dword V */
+#define PSPA_OB_HW_EVENT_PID0_OFFSET 0x04 /* DWORD V+1 */
+#define PSPA_PHYSTATE1_OFFSET 0x08 /* Dword V+2 */
+#define PSPA_OB_HW_EVENT_PID1_OFFSET 0x0C /* DWORD V+3 */
+#define PSPA_PHYSTATE2_OFFSET 0x10 /* Dword V+4 */
+#define PSPA_OB_HW_EVENT_PID2_OFFSET 0x14 /* DWORD V+5 */
+#define PSPA_PHYSTATE3_OFFSET 0x18 /* Dword V+6 */
+#define PSPA_OB_HW_EVENT_PID3_OFFSET 0x1C /* DWORD V+7 */
+#define PSPA_PHYSTATE4_OFFSET 0x20 /* Dword V+8 */
+#define PSPA_OB_HW_EVENT_PID4_OFFSET 0x24 /* DWORD V+9 */
+#define PSPA_PHYSTATE5_OFFSET 0x28 /* Dword V+10 */
+#define PSPA_OB_HW_EVENT_PID5_OFFSET 0x2C /* DWORD V+11 */
+#define PSPA_PHYSTATE6_OFFSET 0x30 /* Dword V+12 */
+#define PSPA_OB_HW_EVENT_PID6_OFFSET 0x34 /* DWORD V+13 */
+#define PSPA_PHYSTATE7_OFFSET 0x38 /* Dword V+14 */
+#define PSPA_OB_HW_EVENT_PID7_OFFSET 0x3C /* DWORD V+15 */
+#define PSPA_PHYSTATE8_OFFSET 0x40 /* DWORD V+16 */
+#define PSPA_OB_HW_EVENT_PID8_OFFSET 0x44 /* DWORD V+17 */
+#define PSPA_PHYSTATE9_OFFSET 0x48 /* DWORD V+18 */
+#define PSPA_OB_HW_EVENT_PID9_OFFSET 0x4C /* DWORD V+19 */
+#define PSPA_PHYSTATE10_OFFSET 0x50 /* DWORD V+20 */
+#define PSPA_OB_HW_EVENT_PID10_OFFSET 0x54 /* DWORD V+21 */
+#define PSPA_PHYSTATE11_OFFSET 0x58 /* DWORD V+22 */
+#define PSPA_OB_HW_EVENT_PID11_OFFSET 0x5C /* DWORD V+23 */
+#define PSPA_PHYSTATE12_OFFSET 0x60 /* DWORD V+24 */
+#define PSPA_OB_HW_EVENT_PID12_OFFSET 0x64 /* DWORD V+25 */
+#define PSPA_PHYSTATE13_OFFSET 0x68 /* DWORD V+26 */
+#define PSPA_OB_HW_EVENT_PID13_OFFSET 0x6c /* DWORD V+27 */
+#define PSPA_PHYSTATE14_OFFSET 0x70 /* DWORD V+28 */
+#define PSPA_OB_HW_EVENT_PID14_OFFSET 0x74 /* DWORD V+29 */
+#define PSPA_PHYSTATE15_OFFSET 0x78 /* DWORD V+30 */
+#define PSPA_OB_HW_EVENT_PID15_OFFSET 0x7c /* DWORD V+31 */
+/* end PSPA */
+
+/* inbound queue configuration offset - byte offset */
+#define IB_PROPERITY_OFFSET 0x00
+#define IB_BASE_ADDR_HI_OFFSET 0x04
+#define IB_BASE_ADDR_LO_OFFSET 0x08
+#define IB_CI_BASE_ADDR_HI_OFFSET 0x0C
+#define IB_CI_BASE_ADDR_LO_OFFSET 0x10
+#define IB_PIPCI_BAR 0x14
+#define IB_PIPCI_BAR_OFFSET 0x18
+#define IB_RESERVED_OFFSET 0x1C
+
+/* outbound queue configuration offset - byte offset */
+#define OB_PROPERITY_OFFSET 0x00
+#define OB_BASE_ADDR_HI_OFFSET 0x04
+#define OB_BASE_ADDR_LO_OFFSET 0x08
+#define OB_PI_BASE_ADDR_HI_OFFSET 0x0C
+#define OB_PI_BASE_ADDR_LO_OFFSET 0x10
+#define OB_CIPCI_BAR 0x14
+#define OB_CIPCI_BAR_OFFSET 0x18
+#define OB_INTERRUPT_COALES_OFFSET 0x1C
+#define OB_DYNAMIC_COALES_OFFSET 0x20
+#define OB_PROPERTY_INT_ENABLE 0x40000000
+
+#define MBIC_NMI_ENABLE_VPE0_IOP 0x000418
+#define MBIC_NMI_ENABLE_VPE0_AAP1 0x000418
+/* PCIE registers - BAR2(0x18), BAR1(win) 0x010000 */
+#define PCIE_EVENT_INTERRUPT_ENABLE 0x003040
+#define PCIE_EVENT_INTERRUPT 0x003044
+#define PCIE_ERROR_INTERRUPT_ENABLE 0x003048
+#define PCIE_ERROR_INTERRUPT 0x00304C
+
+/* SPCV soft reset */
+#define SPC_REG_SOFT_RESET 0x00001000
+#define SPCv_NORMAL_RESET_VALUE 0x1
+
+#define SPCv_SOFT_RESET_READ_MASK 0xC0
+#define SPCv_SOFT_RESET_NO_RESET 0x0
+#define SPCv_SOFT_RESET_NORMAL_RESET_OCCURED 0x40
+#define SPCv_SOFT_RESET_HDA_MODE_OCCURED 0x80
+#define SPCv_SOFT_RESET_CHIP_RESET_OCCURED 0xC0
+
+/* signature definition for host scratch pad0 register */
+#define SPC_SOFT_RESET_SIGNATURE 0x252acbcd
+/* Signature for Soft Reset */
+
+/* SPC Reset register - BAR4(0x20), BAR2(win) (need dynamic mapping) */
+#define SPC_REG_RESET 0x000000/* reset register */
+
+/* bit definition for SPC_RESET register */
+#define SPC_REG_RESET_OSSP 0x00000001
+#define SPC_REG_RESET_RAAE 0x00000002
+#define SPC_REG_RESET_PCS_SPBC 0x00000004
+#define SPC_REG_RESET_PCS_IOP_SS 0x00000008
+#define SPC_REG_RESET_PCS_AAP1_SS 0x00000010
+#define SPC_REG_RESET_PCS_AAP2_SS 0x00000020
+#define SPC_REG_RESET_PCS_LM 0x00000040
+#define SPC_REG_RESET_PCS 0x00000080
+#define SPC_REG_RESET_GSM 0x00000100
+#define SPC_REG_RESET_DDR2 0x00010000
+#define SPC_REG_RESET_BDMA_CORE 0x00020000
+#define SPC_REG_RESET_BDMA_SXCBI 0x00040000
+#define SPC_REG_RESET_PCIE_AL_SXCBI 0x00080000
+#define SPC_REG_RESET_PCIE_PWR 0x00100000
+#define SPC_REG_RESET_PCIE_SFT 0x00200000
+#define SPC_REG_RESET_PCS_SXCBI 0x00400000
+#define SPC_REG_RESET_LMS_SXCBI 0x00800000
+#define SPC_REG_RESET_PMIC_SXCBI 0x01000000
+#define SPC_REG_RESET_PMIC_CORE 0x02000000
+#define SPC_REG_RESET_PCIE_PC_SXCBI 0x04000000
+#define SPC_REG_RESET_DEVICE 0x80000000
+
+/* registers for BAR Shifting - BAR2(0x18), BAR1(win) */
+#define SPCV_IBW_AXI_TRANSLATION_LOW 0x001010
+
+#define MBIC_AAP1_ADDR_BASE 0x060000
+#define MBIC_IOP_ADDR_BASE 0x070000
+#define GSM_ADDR_BASE 0x0700000
+/* Dynamic map through Bar4 - 0x00700000 */
+#define GSM_CONFIG_RESET 0x00000000
+#define RAM_ECC_DB_ERR 0x00000018
+#define GSM_READ_ADDR_PARITY_INDIC 0x00000058
+#define GSM_WRITE_ADDR_PARITY_INDIC 0x00000060
+#define GSM_WRITE_DATA_PARITY_INDIC 0x00000068
+#define GSM_READ_ADDR_PARITY_CHECK 0x00000038
+#define GSM_WRITE_ADDR_PARITY_CHECK 0x00000040
+#define GSM_WRITE_DATA_PARITY_CHECK 0x00000048
+
+#define RB6_ACCESS_REG 0x6A0000
+#define HDAC_EXEC_CMD 0x0002
+#define HDA_C_PA 0xcb
+#define HDA_SEQ_ID_BITS 0x00ff0000
+#define HDA_GSM_OFFSET_BITS 0x00FFFFFF
+#define HDA_GSM_CMD_OFFSET_BITS 0x42C0
+#define HDA_GSM_RSP_OFFSET_BITS 0x42E0
+
+#define MBIC_AAP1_ADDR_BASE 0x060000
+#define MBIC_IOP_ADDR_BASE 0x070000
+#define GSM_ADDR_BASE 0x0700000
+#define SPC_TOP_LEVEL_ADDR_BASE 0x000000
+#define GSM_CONFIG_RESET_VALUE 0x00003b00
+#define GPIO_ADDR_BASE 0x00090000
+#define GPIO_GPIO_0_0UTPUT_CTL_OFFSET 0x0000010c
+
+/* RB6 offset */
+#define SPC_RB6_OFFSET 0x80C0
+/* Magic number of soft reset for RB6 */
+#define RB6_MAGIC_NUMBER_RST 0x1234
+
+/* Device Register status */
+#define DEVREG_SUCCESS 0x00
+#define DEVREG_FAILURE_OUT_OF_RESOURCE 0x01
+#define DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED 0x02
+#define DEVREG_FAILURE_INVALID_PHY_ID 0x03
+#define DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED 0x04
+#define DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE 0x05
+#define DEVREG_FAILURE_PORT_NOT_VALID_STATE 0x06
+#define DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID 0x07
+
+
+#define MEMBASE_II_SHIFT_REGISTER 0x1010
+#endif
Code Review / kvmfornfv.git / blobdiff