--- /dev/null
+#ifndef _AHA152X_H
+#define _AHA152X_H
+
+/*
+ * $Id: aha152x.h,v 2.7 2004/01/24 11:39:03 fischer Exp $
+ */
+
+/* number of queueable commands
+ (unless we support more than 1 cmd_per_lun this should do) */
+#define AHA152X_MAXQUEUE 7
+
+#define AHA152X_REVID "Adaptec 152x SCSI driver; $Revision: 2.7 $"
+
+/* port addresses */
+#define SCSISEQ (HOSTIOPORT0+0x00) /* SCSI sequence control */
+#define SXFRCTL0 (HOSTIOPORT0+0x01) /* SCSI transfer control 0 */
+#define SXFRCTL1 (HOSTIOPORT0+0x02) /* SCSI transfer control 1 */
+#define SCSISIG (HOSTIOPORT0+0x03) /* SCSI signal in/out */
+#define SCSIRATE (HOSTIOPORT0+0x04) /* SCSI rate control */
+#define SELID (HOSTIOPORT0+0x05) /* selection/reselection ID */
+#define SCSIID SELID /* SCSI ID */
+#define SCSIDAT (HOSTIOPORT0+0x06) /* SCSI latched data */
+#define SCSIBUS (HOSTIOPORT0+0x07) /* SCSI data bus */
+#define STCNT0 (HOSTIOPORT0+0x08) /* SCSI transfer count 0 */
+#define STCNT1 (HOSTIOPORT0+0x09) /* SCSI transfer count 1 */
+#define STCNT2 (HOSTIOPORT0+0x0a) /* SCSI transfer count 2 */
+#define SSTAT0 (HOSTIOPORT0+0x0b) /* SCSI interrupt status 0 */
+#define SSTAT1 (HOSTIOPORT0+0x0c) /* SCSI interrupt status 1 */
+#define SSTAT2 (HOSTIOPORT0+0x0d) /* SCSI interrupt status 2 */
+#define SCSITEST (HOSTIOPORT0+0x0e) /* SCSI test control */
+#define SSTAT3 SCSITEST /* SCSI interrupt status 3 */
+#define SSTAT4 (HOSTIOPORT0+0x0f) /* SCSI status 4 */
+#define SIMODE0 (HOSTIOPORT1+0x10) /* SCSI interrupt mode 0 */
+#define SIMODE1 (HOSTIOPORT1+0x11) /* SCSI interrupt mode 1 */
+#define DMACNTRL0 (HOSTIOPORT1+0x12) /* DMA control 0 */
+#define DMACNTRL1 (HOSTIOPORT1+0x13) /* DMA control 1 */
+#define DMASTAT (HOSTIOPORT1+0x14) /* DMA status */
+#define FIFOSTAT (HOSTIOPORT1+0x15) /* FIFO status */
+#define DATAPORT (HOSTIOPORT1+0x16) /* DATA port */
+#define BRSTCNTRL (HOSTIOPORT1+0x18) /* burst control */
+#define PORTA (HOSTIOPORT1+0x1a) /* PORT A */
+#define PORTB (HOSTIOPORT1+0x1b) /* PORT B */
+#define REV (HOSTIOPORT1+0x1c) /* revision */
+#define STACK (HOSTIOPORT1+0x1d) /* stack */
+#define TEST (HOSTIOPORT1+0x1e) /* test register */
+
+#define IO_RANGE 0x20
+
+/* used in aha152x_porttest */
+#define O_PORTA 0x1a /* PORT A */
+#define O_PORTB 0x1b /* PORT B */
+#define O_DMACNTRL1 0x13 /* DMA control 1 */
+#define O_STACK 0x1d /* stack */
+
+/* used in tc1550_porttest */
+#define O_TC_PORTA 0x0a /* PORT A */
+#define O_TC_PORTB 0x0b /* PORT B */
+#define O_TC_DMACNTRL1 0x03 /* DMA control 1 */
+#define O_TC_STACK 0x0d /* stack */
+
+/* bits and bitmasks to ports */
+
+/* SCSI sequence control */
+#define TEMODEO 0x80
+#define ENSELO 0x40
+#define ENSELI 0x20
+#define ENRESELI 0x10
+#define ENAUTOATNO 0x08
+#define ENAUTOATNI 0x04
+#define ENAUTOATNP 0x02
+#define SCSIRSTO 0x01
+
+/* SCSI transfer control 0 */
+#define SCSIEN 0x80
+#define DMAEN 0x40
+#define CH1 0x20
+#define CLRSTCNT 0x10
+#define SPIOEN 0x08
+#define CLRCH1 0x02
+
+/* SCSI transfer control 1 */
+#define BITBUCKET 0x80
+#define SWRAPEN 0x40
+#define ENSPCHK 0x20
+#define STIMESEL 0x18 /* mask */
+#define STIMESEL_ 3
+#define ENSTIMER 0x04
+#define BYTEALIGN 0x02
+
+/* SCSI signal IN */
+#define SIG_CDI 0x80
+#define SIG_IOI 0x40
+#define SIG_MSGI 0x20
+#define SIG_ATNI 0x10
+#define SIG_SELI 0x08
+#define SIG_BSYI 0x04
+#define SIG_REQI 0x02
+#define SIG_ACKI 0x01
+
+/* SCSI Phases */
+#define P_MASK (SIG_MSGI|SIG_CDI|SIG_IOI)
+#define P_DATAO (0)
+#define P_DATAI (SIG_IOI)
+#define P_CMD (SIG_CDI)
+#define P_STATUS (SIG_CDI|SIG_IOI)
+#define P_MSGO (SIG_MSGI|SIG_CDI)
+#define P_MSGI (SIG_MSGI|SIG_CDI|SIG_IOI)
+
+/* SCSI signal OUT */
+#define SIG_CDO 0x80
+#define SIG_IOO 0x40
+#define SIG_MSGO 0x20
+#define SIG_ATNO 0x10
+#define SIG_SELO 0x08
+#define SIG_BSYO 0x04
+#define SIG_REQO 0x02
+#define SIG_ACKO 0x01
+
+/* SCSI rate control */
+#define SXFR 0x70 /* mask */
+#define SXFR_ 4
+#define SOFS 0x0f /* mask */
+
+/* SCSI ID */
+#define OID 0x70
+#define OID_ 4
+#define TID 0x07
+
+/* SCSI transfer count */
+#define GETSTCNT() ( (GETPORT(STCNT2)<<16) \
+ + (GETPORT(STCNT1)<< 8) \
+ + GETPORT(STCNT0) )
+
+#define SETSTCNT(X) { SETPORT(STCNT2, ((X) & 0xFF0000) >> 16); \
+ SETPORT(STCNT1, ((X) & 0x00FF00) >> 8); \
+ SETPORT(STCNT0, ((X) & 0x0000FF) ); }
+
+/* SCSI interrupt status */
+#define TARGET 0x80
+#define SELDO 0x40
+#define SELDI 0x20
+#define SELINGO 0x10
+#define SWRAP 0x08
+#define SDONE 0x04
+#define SPIORDY 0x02
+#define DMADONE 0x01
+
+#define SETSDONE 0x80
+#define CLRSELDO 0x40
+#define CLRSELDI 0x20
+#define CLRSELINGO 0x10
+#define CLRSWRAP 0x08
+#define CLRSDONE 0x04
+#define CLRSPIORDY 0x02
+#define CLRDMADONE 0x01
+
+/* SCSI status 1 */
+#define SELTO 0x80
+#define ATNTARG 0x40
+#define SCSIRSTI 0x20
+#define PHASEMIS 0x10
+#define BUSFREE 0x08
+#define SCSIPERR 0x04
+#define PHASECHG 0x02
+#define REQINIT 0x01
+
+#define CLRSELTIMO 0x80
+#define CLRATNO 0x40
+#define CLRSCSIRSTI 0x20
+#define CLRBUSFREE 0x08
+#define CLRSCSIPERR 0x04
+#define CLRPHASECHG 0x02
+#define CLRREQINIT 0x01
+
+/* SCSI status 2 */
+#define SOFFSET 0x20
+#define SEMPTY 0x10
+#define SFULL 0x08
+#define SFCNT 0x07 /* mask */
+
+/* SCSI status 3 */
+#define SCSICNT 0xf0 /* mask */
+#define SCSICNT_ 4
+#define OFFCNT 0x0f /* mask */
+
+/* SCSI TEST control */
+#define SCTESTU 0x08
+#define SCTESTD 0x04
+#define STCTEST 0x01
+
+/* SCSI status 4 */
+#define SYNCERR 0x04
+#define FWERR 0x02
+#define FRERR 0x01
+
+#define CLRSYNCERR 0x04
+#define CLRFWERR 0x02
+#define CLRFRERR 0x01
+
+/* SCSI interrupt mode 0 */
+#define ENSELDO 0x40
+#define ENSELDI 0x20
+#define ENSELINGO 0x10
+#define ENSWRAP 0x08
+#define ENSDONE 0x04
+#define ENSPIORDY 0x02
+#define ENDMADONE 0x01
+
+/* SCSI interrupt mode 1 */
+#define ENSELTIMO 0x80
+#define ENATNTARG 0x40
+#define ENSCSIRST 0x20
+#define ENPHASEMIS 0x10
+#define ENBUSFREE 0x08
+#define ENSCSIPERR 0x04
+#define ENPHASECHG 0x02
+#define ENREQINIT 0x01
+
+/* DMA control 0 */
+#define ENDMA 0x80
+#define _8BIT 0x40
+#define DMA 0x20
+#define WRITE_READ 0x08
+#define INTEN 0x04
+#define RSTFIFO 0x02
+#define SWINT 0x01
+
+/* DMA control 1 */
+#define PWRDWN 0x80
+#define STK 0x07 /* mask */
+
+/* DMA status */
+#define ATDONE 0x80
+#define WORDRDY 0x40
+#define INTSTAT 0x20
+#define DFIFOFULL 0x10
+#define DFIFOEMP 0x08
+
+/* BURST control */
+#define BON 0xf0
+#define BOFF 0x0f
+
+/* TEST REGISTER */
+#define BOFFTMR 0x40
+#define BONTMR 0x20
+#define STCNTH 0x10
+#define STCNTM 0x08
+#define STCNTL 0x04
+#define SCSIBLK 0x02
+#define DMABLK 0x01
+
+/* On the AHA-152x board PORTA and PORTB contain
+ some information about the board's configuration. */
+typedef union {
+ struct {
+ unsigned reserved:2; /* reserved */
+ unsigned tardisc:1; /* Target disconnect: 0=disabled, 1=enabled */
+ unsigned syncneg:1; /* Initial sync neg: 0=disabled, 1=enabled */
+ unsigned msgclasses:2; /* Message classes
+ 0=#4
+ 1=#0, #1, #2, #3, #4
+ 2=#0, #3, #4
+ 3=#0, #4
+ */
+ unsigned boot:1; /* boot: 0=disabled, 1=enabled */
+ unsigned dma:1; /* Transfer mode: 0=PIO; 1=DMA */
+ unsigned id:3; /* SCSI-id */
+ unsigned irq:2; /* IRQ-Channel: 0,3=12, 1=10, 2=11 */
+ unsigned dmachan:2; /* DMA-Channel: 0=0, 1=5, 2=6, 3=7 */
+ unsigned parity:1; /* SCSI-parity: 1=enabled 0=disabled */
+ } fields;
+ unsigned short port;
+} aha152x_config ;
+
+#define cf_parity fields.parity
+#define cf_dmachan fields.dmachan
+#define cf_irq fields.irq
+#define cf_id fields.id
+#define cf_dma fields.dma
+#define cf_boot fields.boot
+#define cf_msgclasses fields.msgclasses
+#define cf_syncneg fields.syncneg
+#define cf_tardisc fields.tardisc
+#define cf_port port
+
+/* Some macros to manipulate ports and their bits */
+
+#define SETPORT(PORT, VAL) outb( (VAL), (PORT) )
+#define GETPORT(PORT) inb( PORT )
+#define SETBITS(PORT, BITS) outb( (inb(PORT) | (BITS)), (PORT) )
+#define CLRBITS(PORT, BITS) outb( (inb(PORT) & ~(BITS)), (PORT) )
+#define TESTHI(PORT, BITS) ((inb(PORT) & (BITS)) == (BITS))
+#define TESTLO(PORT, BITS) ((inb(PORT) & (BITS)) == 0)
+
+#define SETRATE(RATE) SETPORT(SCSIRATE,(RATE) & 0x7f)
+
+#if defined(AHA152X_DEBUG)
+enum {
+ debug_procinfo = 0x0001,
+ debug_queue = 0x0002,
+ debug_locking = 0x0004,
+ debug_intr = 0x0008,
+ debug_selection = 0x0010,
+ debug_msgo = 0x0020,
+ debug_msgi = 0x0040,
+ debug_status = 0x0080,
+ debug_cmd = 0x0100,
+ debug_datai = 0x0200,
+ debug_datao = 0x0400,
+ debug_eh = 0x0800,
+ debug_done = 0x1000,
+ debug_phases = 0x2000,
+};
+#endif
+
+/* for the pcmcia stub */
+struct aha152x_setup {
+ int io_port;
+ int irq;
+ int scsiid;
+ int reconnect;
+ int parity;
+ int synchronous;
+ int delay;
+ int ext_trans;
+ int tc1550;
+#if defined(AHA152X_DEBUG)
+ int debug;
+#endif
+ char *conf;
+};
+
+struct Scsi_Host *aha152x_probe_one(struct aha152x_setup *);
+void aha152x_release(struct Scsi_Host *);
+int aha152x_host_reset_host(struct Scsi_Host *);
+
+#endif /* _AHA152X_H */
Code Review / kvmfornfv.git / blobdiff