select RTC_LIB
help
Generic RTC class support. If you say yes here, you will
- be allowed to plug one or more RTCs to your system. You will
+ be allowed to plug one or more RTCs to your system. You will
probably want to enable one or more of the interfaces below.
if RTC_CLASS
the value read from a specified RTC device. This is useful to avoid
unnecessary fsck runs at boot time, and to network better.
-config RTC_SYSTOHC
- bool "Set the RTC time based on NTP synchronization"
- default y
- help
- If you say yes here, the system time (wall clock) will be stored
- in the RTC specified by RTC_HCTOSYS_DEVICE approximately every 11
- minutes if userspace reports synchronized NTP status.
-
config RTC_HCTOSYS_DEVICE
string "RTC used to set the system time"
- depends on RTC_HCTOSYS = y || RTC_SYSTOHC = y
+ depends on RTC_HCTOSYS
default "rtc0"
help
The RTC device that will be used to (re)initialize the system
sleep states. Do not specify an RTC here unless it stays powered
during all this system's supported sleep states.
+config RTC_SYSTOHC
+ bool "Set the RTC time based on NTP synchronization"
+ default y
+ help
+ If you say yes here, the system time (wall clock) will be stored
+ in the RTC specified by RTC_HCTOSYS_DEVICE approximately every 11
+ minutes if userspace reports synchronized NTP status.
+
+config RTC_SYSTOHC_DEVICE
+ string "RTC used to synchronize NTP adjustment"
+ depends on RTC_SYSTOHC
+ default RTC_HCTOSYS_DEVICE if RTC_HCTOSYS
+ default "rtc0"
+ help
+ The RTC device used for NTP synchronization. The main difference
+ between RTC_HCTOSYS_DEVICE and RTC_SYSTOHC_DEVICE is that this
+ one can sleep when setting time, because it runs in the workqueue
+ context.
+
config RTC_DEBUG
bool "RTC debug support"
help
config RTC_DRV_88PM860X
tristate "Marvell 88PM860x"
- depends on I2C && MFD_88PM860X
+ depends on MFD_88PM860X
help
If you say yes here you get support for RTC function in Marvell
88PM860x chips.
config RTC_DRV_88PM80X
tristate "Marvell 88PM80x"
- depends on I2C && MFD_88PM800
+ depends on MFD_88PM800
help
If you say yes here you get support for RTC function in Marvell
88PM80x chips.
will be called rtc-88pm80x.
config RTC_DRV_ABB5ZES3
- depends on I2C
- select REGMAP_I2C
- tristate "Abracon AB-RTCMC-32.768kHz-B5ZE-S3"
- help
+ select REGMAP_I2C
+ tristate "Abracon AB-RTCMC-32.768kHz-B5ZE-S3"
+ help
If you say yes here you get support for the Abracon
AB-RTCMC-32.768kHz-B5ZE-S3 I2C RTC chip.
config RTC_DRV_DS1374
tristate "Dallas/Maxim DS1374"
- depends on I2C
help
If you say yes here you get support for Dallas Semiconductor
DS1374 real-time clock chips. If an interrupt is associated
config RTC_DRV_DS3232
tristate "Dallas/Maxim DS3232"
- depends on I2C
help
If you say yes here you get support for Dallas Semiconductor
DS3232 real-time clock chips. If an interrupt is associated
config RTC_DRV_HYM8563
tristate "Haoyu Microelectronics HYM8563"
- depends on I2C && OF
+ depends on OF
help
Say Y to enable support for the HYM8563 I2C RTC chip. Apart
from the usual rtc functions it provides a clock output of
will be called rtc-isl12022.
config RTC_DRV_ISL12057
- depends on I2C
- select REGMAP_I2C
- tristate "Intersil ISL12057"
- help
+ select REGMAP_I2C
+ tristate "Intersil ISL12057"
+ help
If you say yes here you get support for the Intersil ISL12057
I2C RTC chip.
This driver can also be built as a module. If so, the module
will be called rtc-rv3029c2.
+config RTC_DRV_RV8803
+ tristate "Micro Crystal RV8803"
+ help
+ If you say yes here you get support for the Micro Crystal
+ RV8803 RTC chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called rtc-rv8803.
+
config RTC_DRV_S5M
tristate "Samsung S2M/S5M series"
depends on MFD_SEC_CORE
if SPI_MASTER
config RTC_DRV_M41T93
- tristate "ST M41T93"
- help
- If you say yes here you will get support for the
- ST M41T93 SPI RTC chip.
+ tristate "ST M41T93"
+ help
+ If you say yes here you will get support for the
+ ST M41T93 SPI RTC chip.
- This driver can also be built as a module. If so, the module
- will be called rtc-m41t93.
+ This driver can also be built as a module. If so, the module
+ will be called rtc-m41t93.
config RTC_DRV_M41T94
tristate "ST M41T94"
If you say yes here you get support for the
Dallas/Maxim DS1390/93/94 chips.
- This driver only supports the RTC feature, and not other chip
- features such as alarms and trickle charging.
+ This driver supports the RTC feature and trickle charging but not
+ other chip features such as alarms.
This driver can also be built as a module. If so, the module
will be called rtc-ds1390.
will be called rtc-da9055
config RTC_DRV_DA9063
- tristate "Dialog Semiconductor DA9063 RTC"
- depends on MFD_DA9063
+ tristate "Dialog Semiconductor DA9063/DA9062 RTC"
+ depends on MFD_DA9063 || MFD_DA9062
help
If you say yes here you will get support for the RTC subsystem
- of the Dialog Semiconductor DA9063.
+ for the Dialog Semiconductor PMIC chips DA9063 and DA9062.
This driver can also be built as a module. If so, the module
will be called "rtc-da9063".
This driver can also be built as a module. If so, the module
will be called rtc-opal.
+config RTC_DRV_ZYNQMP
+ tristate "Xilinx Zynq Ultrascale+ MPSoC RTC"
+ depends on OF
+ help
+ If you say yes here you get support for the RTC controller found on
+ Xilinx Zynq Ultrascale+ MPSoC.
+
comment "on-CPU RTC drivers"
config RTC_DRV_DAVINCI
Say Y here to enable support for the on-chip RTC found in
most SuperH processors.
- To compile this driver as a module, choose M here: the
+ To compile this driver as a module, choose M here: the
module will be called rtc-sh.
config RTC_DRV_VR41XX
config RTC_DRV_PXA
tristate "PXA27x/PXA3xx"
depends on ARCH_PXA
+ select RTC_DRV_SA1100
help
If you say Y here you will get access to the real time clock
- built into your PXA27x or PXA3xx CPU.
+ built into your PXA27x or PXA3xx CPU. This RTC is actually 2 RTCs
+ consisting of an SA1100 compatible RTC and the extended PXA RTC.
- This RTC driver uses PXA RTC registers available since pxa27x
- series (RDxR, RYxR) instead of legacy RCNR, RTAR.
+ This RTC driver uses PXA RTC registers available since pxa27x
+ series (RDxR, RYxR) instead of legacy RCNR, RTAR.
config RTC_DRV_VT8500
tristate "VIA/WonderMedia 85xx SoC RTC"
This driver can also be built as a module. If so, the module
will be called armada38x-rtc.
+config RTC_DRV_GEMINI
+ tristate "Gemini SoC RTC"
+ depends on ARCH_GEMINI || COMPILE_TEST
+ depends on HAS_IOMEM
+ help
+ If you say Y here you will get support for the
+ RTC found on Gemini SoC's.
+
+ This driver can also be built as a module. If so, the module
+ will be called rtc-gemini.
+
config RTC_DRV_PS3
tristate "PS3 RTC"
depends on PPC_PS3
config RTC_DRV_STMP
tristate "Freescale STMP3xxx/i.MX23/i.MX28 RTC"
depends on ARCH_MXS
+ select STMP_DEVICE
help
If you say yes here you will get support for the onboard
STMP3xxx/i.MX23/i.MX28 RTC.
This driver can also be buillt as a module. If so, the module
will be called rtc-jz4740.
+config RTC_DRV_LPC24XX
+ tristate "NXP RTC for LPC178x/18xx/408x/43xx"
+ depends on ARCH_LPC18XX || COMPILE_TEST
+ depends on OF && HAS_IOMEM
+ help
+ This enables support for the NXP RTC found which can be found on
+ NXP LPC178x/18xx/408x/43xx devices.
+
+ If you have one of the devices above enable this driver to use
+ the hardware RTC. This driver can also be buillt as a module. If
+ so, the module will be called rtc-lpc24xx.
+
config RTC_DRV_LPC32XX
depends on ARCH_LPC32XX
tristate "NXP LPC32XX RTC"
config RTC_DRV_LOONGSON1
tristate "loongson1 RTC support"
- depends on MACH_LOONGSON1
+ depends on MACH_LOONGSON32
help
This is a driver for the loongson1 on-chip Counter0 (Time-Of-Year
counter) to be used as a RTC.
config RTC_DRV_SNVS
tristate "Freescale SNVS RTC support"
+ select REGMAP_MMIO
depends on HAS_IOMEM
depends on OF
help
Say "yes" here to support the real time clock on SiRF SOC chips.
This driver can also be built as a module called rtc-sirfsoc.
+config RTC_DRV_ST_LPC
+ tristate "STMicroelectronics LPC RTC"
+ depends on ARCH_STI
+ depends on OF
+ help
+ Say Y here to include STMicroelectronics Low Power Controller
+ (LPC) based RTC support.
+
+ To compile this driver as a module, choose M here: the
+ module will be called rtc-st-lpc.
+
config RTC_DRV_MOXART
tristate "MOXA ART RTC"
depends on ARCH_MOXART || COMPILE_TEST
This driver can also be built as a module. If so, the module
will be called rtc-moxart
+config RTC_DRV_MT6397
+ tristate "Mediatek Real Time Clock driver"
+ depends on MFD_MT6397 || COMPILE_TEST
+ help
+ This selects the Mediatek(R) RTC driver. RTC is part of Mediatek
+ MT6397 PMIC. You should enable MT6397 PMIC MFD before select
+ Mediatek(R) RTC driver.
+
+ If you want to use Mediatek(R) RTC interface, select Y or M here.
+
config RTC_DRV_XGENE
tristate "APM X-Gene RTC"
depends on HAS_IOMEM
+ depends on ARCH_XGENE || COMPILE_TEST
help
If you say yes here you get support for the APM X-Gene SoC real time
clock.
Code Review / kvmfornfv.git / blobdiff