#include <linux/power_supply.h>
#include <linux/notifier.h>
#include <linux/usb/otg.h>
-#include <linux/regulator/machine.h>
+#include <linux/iio/consumer.h>
+#define TWL4030_BCIMDEN 0x00
+#define TWL4030_BCIMDKEY 0x01
#define TWL4030_BCIMSTATEC 0x02
#define TWL4030_BCIICHG 0x08
#define TWL4030_BCIVAC 0x0a
#define TWL4030_BCIMFSTS4 0x10
#define TWL4030_BCICTL1 0x23
#define TWL4030_BB_CFG 0x12
+#define TWL4030_BCIIREF1 0x27
+#define TWL4030_BCIIREF2 0x28
+#define TWL4030_BCIMFKEY 0x11
+#define TWL4030_BCIMFEN3 0x14
+#define TWL4030_BCIMFTH8 0x1d
+#define TWL4030_BCIMFTH9 0x1e
+#define TWL4030_BCIWDKEY 0x21
#define TWL4030_BCIMFSTS1 0x01
#define TWL4030_BCIAUTOWEN BIT(5)
#define TWL4030_CONFIG_DONE BIT(4)
+#define TWL4030_CVENAC BIT(2)
#define TWL4030_BCIAUTOUSB BIT(1)
#define TWL4030_BCIAUTOAC BIT(0)
#define TWL4030_CGAIN BIT(5)
#define TWL4030_MSTATEC_COMPLETE1 0x0b
#define TWL4030_MSTATEC_COMPLETE4 0x0e
+/*
+ * If AC (Accessory Charger) voltage exceeds 4.5V (MADC 11)
+ * then AC is available.
+ */
+static inline int ac_available(struct iio_channel *channel_vac)
+{
+ int val, err;
+
+ if (!channel_vac)
+ return 0;
+
+ err = iio_read_channel_processed(channel_vac, &val);
+ if (err < 0)
+ return 0;
+ return val > 4500;
+}
+
static bool allow_usb;
module_param(allow_usb, bool, 0644);
MODULE_PARM_DESC(allow_usb, "Allow USB charge drawing default current");
struct work_struct work;
int irq_chg;
int irq_bci;
- struct regulator *usb_reg;
int usb_enabled;
+ /*
+ * ichg_* and *_cur values in uA. If any are 'large', we set
+ * CGAIN to '1' which doubles the range for half the
+ * precision.
+ */
+ unsigned int ichg_eoc, ichg_lo, ichg_hi;
+ unsigned int usb_cur, ac_cur;
+ struct iio_channel *channel_vac;
+ bool ac_is_active;
+ int usb_mode, ac_mode; /* charging mode requested */
+#define CHARGE_OFF 0
+#define CHARGE_AUTO 1
+#define CHARGE_LINEAR 2
+
+ /* When setting the USB current we slowly increase the
+ * requested current until target is reached or the voltage
+ * drops below 4.75V. In the latter case we step back one
+ * step.
+ */
+ unsigned int usb_cur_target;
+ struct delayed_work current_worker;
+#define USB_CUR_STEP 20000 /* 20mA at a time */
+#define USB_MIN_VOLT 4750000 /* 4.75V */
+#define USB_CUR_DELAY msecs_to_jiffies(100)
+#define USB_MAX_CURRENT 1700000 /* TWL4030 caps at 1.7A */
+
unsigned long event;
};
+/* strings for 'usb_mode' values */
+static char *modes[] = { "off", "auto", "continuous" };
+
/*
* clear and set bits on an given register on a given module
*/
}
/*
- * Check if VBUS power is present
+ * TI provided formulas:
+ * CGAIN == 0: ICHG = (BCIICHG * 1.7) / (2^10 - 1) - 0.85
+ * CGAIN == 1: ICHG = (BCIICHG * 3.4) / (2^10 - 1) - 1.7
+ * Here we use integer approximation of:
+ * CGAIN == 0: val * 1.6618 - 0.85 * 1000
+ * CGAIN == 1: (val * 1.6618 - 0.85 * 1000) * 2
+ */
+/*
+ * convert twl register value for currents into uA
+ */
+static int regval2ua(int regval, bool cgain)
+{
+ if (cgain)
+ return (regval * 16618 - 8500 * 1000) / 5;
+ else
+ return (regval * 16618 - 8500 * 1000) / 10;
+}
+
+/*
+ * convert uA currents into twl register value
*/
-static int twl4030_bci_have_vbus(struct twl4030_bci *bci)
+static int ua2regval(int ua, bool cgain)
{
int ret;
- u8 hwsts;
+ if (cgain)
+ ua /= 2;
+ ret = (ua * 10 + 8500 * 1000) / 16618;
+ /* rounding problems */
+ if (ret < 512)
+ ret = 512;
+ return ret;
+}
- ret = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &hwsts,
- TWL4030_PM_MASTER_STS_HW_CONDITIONS);
- if (ret < 0)
- return 0;
+static int twl4030_charger_update_current(struct twl4030_bci *bci)
+{
+ int status;
+ int cur;
+ unsigned reg, cur_reg;
+ u8 bcictl1, oldreg, fullreg;
+ bool cgain = false;
+ u8 boot_bci;
+
+ /*
+ * If AC (Accessory Charger) voltage exceeds 4.5V (MADC 11)
+ * and AC is enabled, set current for 'ac'
+ */
+ if (ac_available(bci->channel_vac)) {
+ cur = bci->ac_cur;
+ bci->ac_is_active = true;
+ } else {
+ cur = bci->usb_cur;
+ bci->ac_is_active = false;
+ if (cur > bci->usb_cur_target) {
+ cur = bci->usb_cur_target;
+ bci->usb_cur = cur;
+ }
+ if (cur < bci->usb_cur_target)
+ schedule_delayed_work(&bci->current_worker, USB_CUR_DELAY);
+ }
+
+ /* First, check thresholds and see if cgain is needed */
+ if (bci->ichg_eoc >= 200000)
+ cgain = true;
+ if (bci->ichg_lo >= 400000)
+ cgain = true;
+ if (bci->ichg_hi >= 820000)
+ cgain = true;
+ if (cur > 852000)
+ cgain = true;
+
+ status = twl4030_bci_read(TWL4030_BCICTL1, &bcictl1);
+ if (status < 0)
+ return status;
+ if (twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &boot_bci,
+ TWL4030_PM_MASTER_BOOT_BCI) < 0)
+ boot_bci = 0;
+ boot_bci &= 7;
+
+ if ((!!cgain) != !!(bcictl1 & TWL4030_CGAIN))
+ /* Need to turn for charging while we change the
+ * CGAIN bit. Leave it off while everything is
+ * updated.
+ */
+ twl4030_clear_set_boot_bci(boot_bci, 0);
+
+ /*
+ * For ichg_eoc, the hardware only supports reg values matching
+ * 100XXXX000, and requires the XXXX be stored in the high nibble
+ * of TWL4030_BCIMFTH8.
+ */
+ reg = ua2regval(bci->ichg_eoc, cgain);
+ if (reg > 0x278)
+ reg = 0x278;
+ if (reg < 0x200)
+ reg = 0x200;
+ reg = (reg >> 3) & 0xf;
+ fullreg = reg << 4;
- dev_dbg(bci->dev, "check_vbus: HW_CONDITIONS %02x\n", hwsts);
+ /*
+ * For ichg_lo, reg value must match 10XXXX0000.
+ * XXXX is stored in low nibble of TWL4030_BCIMFTH8.
+ */
+ reg = ua2regval(bci->ichg_lo, cgain);
+ if (reg > 0x2F0)
+ reg = 0x2F0;
+ if (reg < 0x200)
+ reg = 0x200;
+ reg = (reg >> 4) & 0xf;
+ fullreg |= reg;
+
+ /* ichg_eoc and ichg_lo live in same register */
+ status = twl4030_bci_read(TWL4030_BCIMFTH8, &oldreg);
+ if (status < 0)
+ return status;
+ if (oldreg != fullreg) {
+ status = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0xF4,
+ TWL4030_BCIMFKEY);
+ if (status < 0)
+ return status;
+ twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE,
+ fullreg, TWL4030_BCIMFTH8);
+ }
- /* in case we also have STS_USB_ID, VBUS is driven by TWL itself */
- if ((hwsts & TWL4030_STS_VBUS) && !(hwsts & TWL4030_STS_USB_ID))
- return 1;
+ /* ichg_hi threshold must be 1XXXX01100 (I think) */
+ reg = ua2regval(bci->ichg_hi, cgain);
+ if (reg > 0x3E0)
+ reg = 0x3E0;
+ if (reg < 0x200)
+ reg = 0x200;
+ fullreg = (reg >> 5) & 0xF;
+ fullreg <<= 4;
+ status = twl4030_bci_read(TWL4030_BCIMFTH9, &oldreg);
+ if (status < 0)
+ return status;
+ if ((oldreg & 0xF0) != fullreg) {
+ fullreg |= (oldreg & 0x0F);
+ status = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0xE7,
+ TWL4030_BCIMFKEY);
+ if (status < 0)
+ return status;
+ twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE,
+ fullreg, TWL4030_BCIMFTH9);
+ }
+ /*
+ * And finally, set the current. This is stored in
+ * two registers.
+ */
+ reg = ua2regval(cur, cgain);
+ /* we have only 10 bits */
+ if (reg > 0x3ff)
+ reg = 0x3ff;
+ status = twl4030_bci_read(TWL4030_BCIIREF1, &oldreg);
+ if (status < 0)
+ return status;
+ cur_reg = oldreg;
+ status = twl4030_bci_read(TWL4030_BCIIREF2, &oldreg);
+ if (status < 0)
+ return status;
+ cur_reg |= oldreg << 8;
+ if (reg != oldreg) {
+ /* disable write protection for one write access for
+ * BCIIREF */
+ status = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0xE7,
+ TWL4030_BCIMFKEY);
+ if (status < 0)
+ return status;
+ status = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE,
+ (reg & 0x100) ? 3 : 2,
+ TWL4030_BCIIREF2);
+ if (status < 0)
+ return status;
+ /* disable write protection for one write access for
+ * BCIIREF */
+ status = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0xE7,
+ TWL4030_BCIMFKEY);
+ if (status < 0)
+ return status;
+ status = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE,
+ reg & 0xff,
+ TWL4030_BCIIREF1);
+ }
+ if ((!!cgain) != !!(bcictl1 & TWL4030_CGAIN)) {
+ /* Flip CGAIN and re-enable charging */
+ bcictl1 ^= TWL4030_CGAIN;
+ twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE,
+ bcictl1, TWL4030_BCICTL1);
+ twl4030_clear_set_boot_bci(0, boot_bci);
+ }
return 0;
}
+static int twl4030_charger_get_current(void);
+
+static void twl4030_current_worker(struct work_struct *data)
+{
+ int v, curr;
+ int res;
+ struct twl4030_bci *bci = container_of(data, struct twl4030_bci,
+ current_worker.work);
+
+ res = twl4030bci_read_adc_val(TWL4030_BCIVBUS);
+ if (res < 0)
+ v = 0;
+ else
+ /* BCIVBUS uses ADCIN8, 7/1023 V/step */
+ v = res * 6843;
+ curr = twl4030_charger_get_current();
+
+ dev_dbg(bci->dev, "v=%d cur=%d limit=%d target=%d\n", v, curr,
+ bci->usb_cur, bci->usb_cur_target);
+
+ if (v < USB_MIN_VOLT) {
+ /* Back up and stop adjusting. */
+ bci->usb_cur -= USB_CUR_STEP;
+ bci->usb_cur_target = bci->usb_cur;
+ } else if (bci->usb_cur >= bci->usb_cur_target ||
+ bci->usb_cur + USB_CUR_STEP > USB_MAX_CURRENT) {
+ /* Reached target and voltage is OK - stop */
+ return;
+ } else {
+ bci->usb_cur += USB_CUR_STEP;
+ schedule_delayed_work(&bci->current_worker, USB_CUR_DELAY);
+ }
+ twl4030_charger_update_current(bci);
+}
+
/*
* Enable/Disable USB Charge functionality.
*/
{
int ret;
- if (enable) {
- /* Check for USB charger connected */
- if (!twl4030_bci_have_vbus(bci))
- return -ENODEV;
+ if (bci->usb_mode == CHARGE_OFF)
+ enable = false;
+ if (enable && !IS_ERR_OR_NULL(bci->transceiver)) {
- /*
- * Until we can find out what current the device can provide,
- * require a module param to enable USB charging.
- */
- if (!allow_usb) {
- dev_warn(bci->dev, "USB charging is disabled.\n");
- return -EACCES;
- }
+ twl4030_charger_update_current(bci);
- /* Need to keep regulator on */
+ /* Need to keep phy powered */
if (!bci->usb_enabled) {
- ret = regulator_enable(bci->usb_reg);
- if (ret) {
- dev_err(bci->dev,
- "Failed to enable regulator\n");
- return ret;
- }
+ pm_runtime_get_sync(bci->transceiver->dev);
bci->usb_enabled = 1;
}
- /* forcing the field BCIAUTOUSB (BOOT_BCI[1]) to 1 */
- ret = twl4030_clear_set_boot_bci(0, TWL4030_BCIAUTOUSB);
- if (ret < 0)
- return ret;
+ if (bci->usb_mode == CHARGE_AUTO)
+ /* forcing the field BCIAUTOUSB (BOOT_BCI[1]) to 1 */
+ ret = twl4030_clear_set_boot_bci(0, TWL4030_BCIAUTOUSB);
/* forcing USBFASTMCHG(BCIMFSTS4[2]) to 1 */
ret = twl4030_clear_set(TWL_MODULE_MAIN_CHARGE, 0,
TWL4030_USBFASTMCHG, TWL4030_BCIMFSTS4);
+ if (bci->usb_mode == CHARGE_LINEAR) {
+ twl4030_clear_set_boot_bci(TWL4030_BCIAUTOAC|TWL4030_CVENAC, 0);
+ /* Watch dog key: WOVF acknowledge */
+ ret = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0x33,
+ TWL4030_BCIWDKEY);
+ /* 0x24 + EKEY6: off mode */
+ ret = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0x2a,
+ TWL4030_BCIMDKEY);
+ /* EKEY2: Linear charge: USB path */
+ ret = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0x26,
+ TWL4030_BCIMDKEY);
+ /* WDKEY5: stop watchdog count */
+ ret = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0xf3,
+ TWL4030_BCIWDKEY);
+ /* enable MFEN3 access */
+ ret = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0x9c,
+ TWL4030_BCIMFKEY);
+ /* ICHGEOCEN - end-of-charge monitor (current < 80mA)
+ * (charging continues)
+ * ICHGLOWEN - current level monitor (charge continues)
+ * don't monitor over-current or heat save
+ */
+ ret = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0xf0,
+ TWL4030_BCIMFEN3);
+ }
} else {
ret = twl4030_clear_set_boot_bci(TWL4030_BCIAUTOUSB, 0);
+ ret |= twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE, 0x2a,
+ TWL4030_BCIMDKEY);
if (bci->usb_enabled) {
- regulator_disable(bci->usb_reg);
+ pm_runtime_mark_last_busy(bci->transceiver->dev);
+ pm_runtime_put_autosuspend(bci->transceiver->dev);
bci->usb_enabled = 0;
}
+ bci->usb_cur = 0;
}
return ret;
/*
* Enable/Disable AC Charge funtionality.
*/
-static int twl4030_charger_enable_ac(bool enable)
+static int twl4030_charger_enable_ac(struct twl4030_bci *bci, bool enable)
{
int ret;
+ if (bci->ac_mode == CHARGE_OFF)
+ enable = false;
+
if (enable)
ret = twl4030_clear_set_boot_bci(0, TWL4030_BCIAUTOAC);
else
struct twl4030_bci *bci = arg;
dev_dbg(bci->dev, "CHG_PRES irq\n");
+ /* reset current on each 'plug' event */
+ bci->ac_cur = 500000;
+ twl4030_charger_update_current(bci);
power_supply_changed(bci->ac);
power_supply_changed(bci->usb);
power_supply_changed(bci->ac);
power_supply_changed(bci->usb);
}
+ twl4030_charger_update_current(bci);
/* various monitoring events, for now we just log them here */
if (irqs1 & (TWL4030_TBATOR2 | TWL4030_TBATOR1))
return IRQ_HANDLED;
}
+/*
+ * Provide "max_current" attribute in sysfs.
+ */
+static ssize_t
+twl4030_bci_max_current_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t n)
+{
+ struct twl4030_bci *bci = dev_get_drvdata(dev->parent);
+ int cur = 0;
+ int status = 0;
+ status = kstrtoint(buf, 10, &cur);
+ if (status)
+ return status;
+ if (cur < 0)
+ return -EINVAL;
+ if (dev == &bci->ac->dev)
+ bci->ac_cur = cur;
+ else
+ bci->usb_cur_target = cur;
+
+ twl4030_charger_update_current(bci);
+ return n;
+}
+
+/*
+ * sysfs max_current show
+ */
+static ssize_t twl4030_bci_max_current_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ int status = 0;
+ int cur = -1;
+ u8 bcictl1;
+ struct twl4030_bci *bci = dev_get_drvdata(dev->parent);
+
+ if (dev == &bci->ac->dev) {
+ if (!bci->ac_is_active)
+ cur = bci->ac_cur;
+ } else {
+ if (bci->ac_is_active)
+ cur = bci->usb_cur_target;
+ }
+ if (cur < 0) {
+ cur = twl4030bci_read_adc_val(TWL4030_BCIIREF1);
+ if (cur < 0)
+ return cur;
+ status = twl4030_bci_read(TWL4030_BCICTL1, &bcictl1);
+ if (status < 0)
+ return status;
+ cur = regval2ua(cur, bcictl1 & TWL4030_CGAIN);
+ }
+ return scnprintf(buf, PAGE_SIZE, "%u\n", cur);
+}
+
+static DEVICE_ATTR(max_current, 0644, twl4030_bci_max_current_show,
+ twl4030_bci_max_current_store);
+
static void twl4030_bci_usb_work(struct work_struct *data)
{
struct twl4030_bci *bci = container_of(data, struct twl4030_bci, work);
dev_dbg(bci->dev, "OTG notify %lu\n", val);
+ /* reset current on each 'plug' event */
+ if (allow_usb)
+ bci->usb_cur_target = 500000;
+ else
+ bci->usb_cur_target = 100000;
+
bci->event = val;
schedule_work(&bci->work);
}
/*
- * TI provided formulas:
- * CGAIN == 0: ICHG = (BCIICHG * 1.7) / (2^10 - 1) - 0.85
- * CGAIN == 1: ICHG = (BCIICHG * 3.4) / (2^10 - 1) - 1.7
- * Here we use integer approximation of:
- * CGAIN == 0: val * 1.6618 - 0.85
- * CGAIN == 1: (val * 1.6618 - 0.85) * 2
+ * sysfs charger enabled store
*/
+static ssize_t
+twl4030_bci_mode_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t n)
+{
+ struct twl4030_bci *bci = dev_get_drvdata(dev->parent);
+ int mode;
+ int status;
+
+ if (sysfs_streq(buf, modes[0]))
+ mode = 0;
+ else if (sysfs_streq(buf, modes[1]))
+ mode = 1;
+ else if (sysfs_streq(buf, modes[2]))
+ mode = 2;
+ else
+ return -EINVAL;
+ if (dev == &bci->ac->dev) {
+ if (mode == 2)
+ return -EINVAL;
+ twl4030_charger_enable_ac(bci, false);
+ bci->ac_mode = mode;
+ status = twl4030_charger_enable_ac(bci, true);
+ } else {
+ twl4030_charger_enable_usb(bci, false);
+ bci->usb_mode = mode;
+ status = twl4030_charger_enable_usb(bci, true);
+ }
+ return (status == 0) ? n : status;
+}
+
+/*
+ * sysfs charger enabled show
+ */
+static ssize_t
+twl4030_bci_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct twl4030_bci *bci = dev_get_drvdata(dev->parent);
+ int len = 0;
+ int i;
+ int mode = bci->usb_mode;
+
+ if (dev == &bci->ac->dev)
+ mode = bci->ac_mode;
+
+ for (i = 0; i < ARRAY_SIZE(modes); i++)
+ if (mode == i)
+ len += snprintf(buf+len, PAGE_SIZE-len,
+ "[%s] ", modes[i]);
+ else
+ len += snprintf(buf+len, PAGE_SIZE-len,
+ "%s ", modes[i]);
+ buf[len-1] = '\n';
+ return len;
+}
+static DEVICE_ATTR(mode, 0644, twl4030_bci_mode_show,
+ twl4030_bci_mode_store);
+
static int twl4030_charger_get_current(void)
{
int curr;
if (ret)
return ret;
- ret = (curr * 16618 - 850 * 10000) / 10;
- if (bcictl1 & TWL4030_CGAIN)
- ret *= 2;
-
- return ret;
+ return regval2ua(curr, bcictl1 & TWL4030_CGAIN);
}
/*
is_charging = state & TWL4030_MSTATEC_USB;
else
is_charging = state & TWL4030_MSTATEC_AC;
+ if (!is_charging) {
+ u8 s;
+ twl4030_bci_read(TWL4030_BCIMDEN, &s);
+ if (psy->desc->type == POWER_SUPPLY_TYPE_USB)
+ is_charging = s & 1;
+ else
+ is_charging = s & 2;
+ if (is_charging)
+ /* A little white lie */
+ state = TWL4030_MSTATEC_QUICK1;
+ }
switch (psp) {
case POWER_SUPPLY_PROP_STATUS:
.get_property = twl4030_bci_get_property,
};
-static int __init twl4030_bci_probe(struct platform_device *pdev)
+static int twl4030_bci_probe(struct platform_device *pdev)
{
struct twl4030_bci *bci;
const struct twl4030_bci_platform_data *pdata = pdev->dev.platform_data;
int ret;
u32 reg;
- bci = kzalloc(sizeof(*bci), GFP_KERNEL);
+ bci = devm_kzalloc(&pdev->dev, sizeof(*bci), GFP_KERNEL);
if (bci == NULL)
return -ENOMEM;
if (!pdata)
pdata = twl4030_bci_parse_dt(&pdev->dev);
+ bci->ichg_eoc = 80100; /* Stop charging when current drops to here */
+ bci->ichg_lo = 241000; /* Low threshold */
+ bci->ichg_hi = 500000; /* High threshold */
+ bci->ac_cur = 500000; /* 500mA */
+ if (allow_usb)
+ bci->usb_cur_target = 500000; /* 500mA */
+ else
+ bci->usb_cur_target = 100000; /* 100mA */
+ bci->usb_mode = CHARGE_AUTO;
+ bci->ac_mode = CHARGE_AUTO;
+
bci->dev = &pdev->dev;
bci->irq_chg = platform_get_irq(pdev, 0);
bci->irq_bci = platform_get_irq(pdev, 1);
ret = twl4030_is_battery_present(bci);
if (ret) {
dev_crit(&pdev->dev, "Battery was not detected:%d\n", ret);
- goto fail_no_battery;
+ return ret;
}
platform_set_drvdata(pdev, bci);
- bci->ac = power_supply_register(&pdev->dev, &twl4030_bci_ac_desc,
- NULL);
+ bci->ac = devm_power_supply_register(&pdev->dev, &twl4030_bci_ac_desc,
+ NULL);
if (IS_ERR(bci->ac)) {
ret = PTR_ERR(bci->ac);
dev_err(&pdev->dev, "failed to register ac: %d\n", ret);
- goto fail_register_ac;
+ return ret;
}
- bci->usb_reg = regulator_get(bci->dev, "bci3v1");
-
- bci->usb = power_supply_register(&pdev->dev, &twl4030_bci_usb_desc,
- NULL);
+ bci->usb = devm_power_supply_register(&pdev->dev, &twl4030_bci_usb_desc,
+ NULL);
if (IS_ERR(bci->usb)) {
ret = PTR_ERR(bci->usb);
dev_err(&pdev->dev, "failed to register usb: %d\n", ret);
- goto fail_register_usb;
+ return ret;
}
- ret = request_threaded_irq(bci->irq_chg, NULL,
+ ret = devm_request_threaded_irq(&pdev->dev, bci->irq_chg, NULL,
twl4030_charger_interrupt, IRQF_ONESHOT, pdev->name,
bci);
if (ret < 0) {
dev_err(&pdev->dev, "could not request irq %d, status %d\n",
bci->irq_chg, ret);
- goto fail_chg_irq;
+ return ret;
}
- ret = request_threaded_irq(bci->irq_bci, NULL,
+ ret = devm_request_threaded_irq(&pdev->dev, bci->irq_bci, NULL,
twl4030_bci_interrupt, IRQF_ONESHOT, pdev->name, bci);
if (ret < 0) {
dev_err(&pdev->dev, "could not request irq %d, status %d\n",
bci->irq_bci, ret);
- goto fail_bci_irq;
+ return ret;
+ }
+
+ bci->channel_vac = iio_channel_get(&pdev->dev, "vac");
+ if (IS_ERR(bci->channel_vac)) {
+ bci->channel_vac = NULL;
+ dev_warn(&pdev->dev, "could not request vac iio channel");
}
INIT_WORK(&bci->work, twl4030_bci_usb_work);
+ INIT_DELAYED_WORK(&bci->current_worker, twl4030_current_worker);
- bci->transceiver = usb_get_phy(USB_PHY_TYPE_USB2);
- if (!IS_ERR_OR_NULL(bci->transceiver)) {
- bci->usb_nb.notifier_call = twl4030_bci_usb_ncb;
- usb_register_notifier(bci->transceiver, &bci->usb_nb);
+ bci->usb_nb.notifier_call = twl4030_bci_usb_ncb;
+ if (bci->dev->of_node) {
+ struct device_node *phynode;
+
+ phynode = of_find_compatible_node(bci->dev->of_node->parent,
+ NULL, "ti,twl4030-usb");
+ if (phynode)
+ bci->transceiver = devm_usb_get_phy_by_node(
+ bci->dev, phynode, &bci->usb_nb);
}
/* Enable interrupts now. */
TWL4030_INTERRUPTS_BCIIMR1A);
if (ret < 0) {
dev_err(&pdev->dev, "failed to unmask interrupts: %d\n", ret);
- goto fail_unmask_interrupts;
+ goto fail;
}
reg = ~(u32)(TWL4030_VBATOV | TWL4030_VBUSOV | TWL4030_ACCHGOV);
if (ret < 0)
dev_warn(&pdev->dev, "failed to unmask interrupts: %d\n", ret);
- twl4030_charger_enable_ac(true);
- twl4030_charger_enable_usb(bci, true);
+ twl4030_charger_update_current(bci);
+ if (device_create_file(&bci->usb->dev, &dev_attr_max_current))
+ dev_warn(&pdev->dev, "could not create sysfs file\n");
+ if (device_create_file(&bci->usb->dev, &dev_attr_mode))
+ dev_warn(&pdev->dev, "could not create sysfs file\n");
+ if (device_create_file(&bci->ac->dev, &dev_attr_mode))
+ dev_warn(&pdev->dev, "could not create sysfs file\n");
+ if (device_create_file(&bci->ac->dev, &dev_attr_max_current))
+ dev_warn(&pdev->dev, "could not create sysfs file\n");
+
+ twl4030_charger_enable_ac(bci, true);
+ if (!IS_ERR_OR_NULL(bci->transceiver))
+ twl4030_bci_usb_ncb(&bci->usb_nb,
+ bci->transceiver->last_event,
+ NULL);
+ else
+ twl4030_charger_enable_usb(bci, false);
if (pdata)
twl4030_charger_enable_backup(pdata->bb_uvolt,
pdata->bb_uamp);
twl4030_charger_enable_backup(0, 0);
return 0;
-
-fail_unmask_interrupts:
- if (!IS_ERR_OR_NULL(bci->transceiver)) {
- usb_unregister_notifier(bci->transceiver, &bci->usb_nb);
- usb_put_phy(bci->transceiver);
- }
- free_irq(bci->irq_bci, bci);
-fail_bci_irq:
- free_irq(bci->irq_chg, bci);
-fail_chg_irq:
- power_supply_unregister(bci->usb);
-fail_register_usb:
- power_supply_unregister(bci->ac);
-fail_register_ac:
-fail_no_battery:
- kfree(bci);
+fail:
+ iio_channel_release(bci->channel_vac);
return ret;
}
{
struct twl4030_bci *bci = platform_get_drvdata(pdev);
- twl4030_charger_enable_ac(false);
+ twl4030_charger_enable_ac(bci, false);
twl4030_charger_enable_usb(bci, false);
twl4030_charger_enable_backup(0, 0);
+ iio_channel_release(bci->channel_vac);
+
+ device_remove_file(&bci->usb->dev, &dev_attr_max_current);
+ device_remove_file(&bci->usb->dev, &dev_attr_mode);
+ device_remove_file(&bci->ac->dev, &dev_attr_max_current);
+ device_remove_file(&bci->ac->dev, &dev_attr_mode);
/* mask interrupts */
twl_i2c_write_u8(TWL4030_MODULE_INTERRUPTS, 0xff,
TWL4030_INTERRUPTS_BCIIMR1A);
twl_i2c_write_u8(TWL4030_MODULE_INTERRUPTS, 0xff,
TWL4030_INTERRUPTS_BCIIMR2A);
- if (!IS_ERR_OR_NULL(bci->transceiver)) {
- usb_unregister_notifier(bci->transceiver, &bci->usb_nb);
- usb_put_phy(bci->transceiver);
- }
- free_irq(bci->irq_bci, bci);
- free_irq(bci->irq_chg, bci);
- power_supply_unregister(bci->usb);
- power_supply_unregister(bci->ac);
- kfree(bci);
-
return 0;
}
MODULE_DEVICE_TABLE(of, twl_bci_of_match);
static struct platform_driver twl4030_bci_driver = {
+ .probe = twl4030_bci_probe,
.driver = {
.name = "twl4030_bci",
.of_match_table = of_match_ptr(twl_bci_of_match),
},
.remove = __exit_p(twl4030_bci_remove),
};
-
-module_platform_driver_probe(twl4030_bci_driver, twl4030_bci_probe);
+module_platform_driver(twl4030_bci_driver);
MODULE_AUTHOR("GraÅžvydas Ignotas");
MODULE_DESCRIPTION("TWL4030 Battery Charger Interface driver");
Code Review / kvmfornfv.git / blobdiff