--- /dev/null
+/*
+ * at91 pinctrl driver based on at91 pinmux core
+ *
+ * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2 only
+ */
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+/* Since we request GPIOs from ourself */
+#include <linux/pinctrl/consumer.h>
+
+#include "pinctrl-at91.h"
+#include "core.h"
+
+#define MAX_GPIO_BANKS 5
+#define MAX_NB_GPIO_PER_BANK 32
+
+struct at91_pinctrl_mux_ops;
+
+struct at91_gpio_chip {
+ struct gpio_chip chip;
+ struct pinctrl_gpio_range range;
+ struct at91_gpio_chip *next; /* Bank sharing same clock */
+ int pioc_hwirq; /* PIO bank interrupt identifier on AIC */
+ int pioc_virq; /* PIO bank Linux virtual interrupt */
+ int pioc_idx; /* PIO bank index */
+ void __iomem *regbase; /* PIO bank virtual address */
+ struct clk *clock; /* associated clock */
+ struct at91_pinctrl_mux_ops *ops; /* ops */
+};
+
+#define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip)
+
+static struct at91_gpio_chip *gpio_chips[MAX_GPIO_BANKS];
+
+static int gpio_banks;
+
+#define PULL_UP (1 << 0)
+#define MULTI_DRIVE (1 << 1)
+#define DEGLITCH (1 << 2)
+#define PULL_DOWN (1 << 3)
+#define DIS_SCHMIT (1 << 4)
+#define DRIVE_STRENGTH_SHIFT 5
+#define DRIVE_STRENGTH_MASK 0x3
+#define DRIVE_STRENGTH (DRIVE_STRENGTH_MASK << DRIVE_STRENGTH_SHIFT)
+#define DEBOUNCE (1 << 16)
+#define DEBOUNCE_VAL_SHIFT 17
+#define DEBOUNCE_VAL (0x3fff << DEBOUNCE_VAL_SHIFT)
+
+/**
+ * These defines will translated the dt binding settings to our internal
+ * settings. They are not necessarily the same value as the register setting.
+ * The actual drive strength current of low, medium and high must be looked up
+ * from the corresponding device datasheet. This value is different for pins
+ * that are even in the same banks. It is also dependent on VCC.
+ * DRIVE_STRENGTH_DEFAULT is just a placeholder to avoid changing the drive
+ * strength when there is no dt config for it.
+ */
+#define DRIVE_STRENGTH_DEFAULT (0 << DRIVE_STRENGTH_SHIFT)
+#define DRIVE_STRENGTH_LOW (1 << DRIVE_STRENGTH_SHIFT)
+#define DRIVE_STRENGTH_MED (2 << DRIVE_STRENGTH_SHIFT)
+#define DRIVE_STRENGTH_HI (3 << DRIVE_STRENGTH_SHIFT)
+
+/**
+ * struct at91_pmx_func - describes AT91 pinmux functions
+ * @name: the name of this specific function
+ * @groups: corresponding pin groups
+ * @ngroups: the number of groups
+ */
+struct at91_pmx_func {
+ const char *name;
+ const char **groups;
+ unsigned ngroups;
+};
+
+enum at91_mux {
+ AT91_MUX_GPIO = 0,
+ AT91_MUX_PERIPH_A = 1,
+ AT91_MUX_PERIPH_B = 2,
+ AT91_MUX_PERIPH_C = 3,
+ AT91_MUX_PERIPH_D = 4,
+};
+
+/**
+ * struct at91_pmx_pin - describes an At91 pin mux
+ * @bank: the bank of the pin
+ * @pin: the pin number in the @bank
+ * @mux: the mux mode : gpio or periph_x of the pin i.e. alternate function.
+ * @conf: the configuration of the pin: PULL_UP, MULTIDRIVE etc...
+ */
+struct at91_pmx_pin {
+ uint32_t bank;
+ uint32_t pin;
+ enum at91_mux mux;
+ unsigned long conf;
+};
+
+/**
+ * struct at91_pin_group - describes an At91 pin group
+ * @name: the name of this specific pin group
+ * @pins_conf: the mux mode for each pin in this group. The size of this
+ * array is the same as pins.
+ * @pins: an array of discrete physical pins used in this group, taken
+ * from the driver-local pin enumeration space
+ * @npins: the number of pins in this group array, i.e. the number of
+ * elements in .pins so we can iterate over that array
+ */
+struct at91_pin_group {
+ const char *name;
+ struct at91_pmx_pin *pins_conf;
+ unsigned int *pins;
+ unsigned npins;
+};
+
+/**
+ * struct at91_pinctrl_mux_ops - describes an AT91 mux ops group
+ * on new IP with support for periph C and D the way to mux in
+ * periph A and B has changed
+ * So provide the right call back
+ * if not present means the IP does not support it
+ * @get_periph: return the periph mode configured
+ * @mux_A_periph: mux as periph A
+ * @mux_B_periph: mux as periph B
+ * @mux_C_periph: mux as periph C
+ * @mux_D_periph: mux as periph D
+ * @get_deglitch: get deglitch status
+ * @set_deglitch: enable/disable deglitch
+ * @get_debounce: get debounce status
+ * @set_debounce: enable/disable debounce
+ * @get_pulldown: get pulldown status
+ * @set_pulldown: enable/disable pulldown
+ * @get_schmitt_trig: get schmitt trigger status
+ * @disable_schmitt_trig: disable schmitt trigger
+ * @irq_type: return irq type
+ */
+struct at91_pinctrl_mux_ops {
+ enum at91_mux (*get_periph)(void __iomem *pio, unsigned mask);
+ void (*mux_A_periph)(void __iomem *pio, unsigned mask);
+ void (*mux_B_periph)(void __iomem *pio, unsigned mask);
+ void (*mux_C_periph)(void __iomem *pio, unsigned mask);
+ void (*mux_D_periph)(void __iomem *pio, unsigned mask);
+ bool (*get_deglitch)(void __iomem *pio, unsigned pin);
+ void (*set_deglitch)(void __iomem *pio, unsigned mask, bool is_on);
+ bool (*get_debounce)(void __iomem *pio, unsigned pin, u32 *div);
+ void (*set_debounce)(void __iomem *pio, unsigned mask, bool is_on, u32 div);
+ bool (*get_pulldown)(void __iomem *pio, unsigned pin);
+ void (*set_pulldown)(void __iomem *pio, unsigned mask, bool is_on);
+ bool (*get_schmitt_trig)(void __iomem *pio, unsigned pin);
+ void (*disable_schmitt_trig)(void __iomem *pio, unsigned mask);
+ unsigned (*get_drivestrength)(void __iomem *pio, unsigned pin);
+ void (*set_drivestrength)(void __iomem *pio, unsigned pin,
+ u32 strength);
+ /* irq */
+ int (*irq_type)(struct irq_data *d, unsigned type);
+};
+
+static int gpio_irq_type(struct irq_data *d, unsigned type);
+static int alt_gpio_irq_type(struct irq_data *d, unsigned type);
+
+struct at91_pinctrl {
+ struct device *dev;
+ struct pinctrl_dev *pctl;
+
+ int nactive_banks;
+
+ uint32_t *mux_mask;
+ int nmux;
+
+ struct at91_pmx_func *functions;
+ int nfunctions;
+
+ struct at91_pin_group *groups;
+ int ngroups;
+
+ struct at91_pinctrl_mux_ops *ops;
+};
+
+static const inline struct at91_pin_group *at91_pinctrl_find_group_by_name(
+ const struct at91_pinctrl *info,
+ const char *name)
+{
+ const struct at91_pin_group *grp = NULL;
+ int i;
+
+ for (i = 0; i < info->ngroups; i++) {
+ if (strcmp(info->groups[i].name, name))
+ continue;
+
+ grp = &info->groups[i];
+ dev_dbg(info->dev, "%s: %d 0:%d\n", name, grp->npins, grp->pins[0]);
+ break;
+ }
+
+ return grp;
+}
+
+static int at91_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+
+ return info->ngroups;
+}
+
+static const char *at91_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned selector)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+
+ return info->groups[selector].name;
+}
+
+static int at91_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector,
+ const unsigned **pins,
+ unsigned *npins)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+
+ if (selector >= info->ngroups)
+ return -EINVAL;
+
+ *pins = info->groups[selector].pins;
+ *npins = info->groups[selector].npins;
+
+ return 0;
+}
+
+static void at91_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s,
+ unsigned offset)
+{
+ seq_printf(s, "%s", dev_name(pctldev->dev));
+}
+
+static int at91_dt_node_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **map, unsigned *num_maps)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+ const struct at91_pin_group *grp;
+ struct pinctrl_map *new_map;
+ struct device_node *parent;
+ int map_num = 1;
+ int i;
+
+ /*
+ * first find the group of this node and check if we need to create
+ * config maps for pins
+ */
+ grp = at91_pinctrl_find_group_by_name(info, np->name);
+ if (!grp) {
+ dev_err(info->dev, "unable to find group for node %s\n",
+ np->name);
+ return -EINVAL;
+ }
+
+ map_num += grp->npins;
+ new_map = devm_kzalloc(pctldev->dev, sizeof(*new_map) * map_num, GFP_KERNEL);
+ if (!new_map)
+ return -ENOMEM;
+
+ *map = new_map;
+ *num_maps = map_num;
+
+ /* create mux map */
+ parent = of_get_parent(np);
+ if (!parent) {
+ devm_kfree(pctldev->dev, new_map);
+ return -EINVAL;
+ }
+ new_map[0].type = PIN_MAP_TYPE_MUX_GROUP;
+ new_map[0].data.mux.function = parent->name;
+ new_map[0].data.mux.group = np->name;
+ of_node_put(parent);
+
+ /* create config map */
+ new_map++;
+ for (i = 0; i < grp->npins; i++) {
+ new_map[i].type = PIN_MAP_TYPE_CONFIGS_PIN;
+ new_map[i].data.configs.group_or_pin =
+ pin_get_name(pctldev, grp->pins[i]);
+ new_map[i].data.configs.configs = &grp->pins_conf[i].conf;
+ new_map[i].data.configs.num_configs = 1;
+ }
+
+ dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n",
+ (*map)->data.mux.function, (*map)->data.mux.group, map_num);
+
+ return 0;
+}
+
+static void at91_dt_free_map(struct pinctrl_dev *pctldev,
+ struct pinctrl_map *map, unsigned num_maps)
+{
+}
+
+static const struct pinctrl_ops at91_pctrl_ops = {
+ .get_groups_count = at91_get_groups_count,
+ .get_group_name = at91_get_group_name,
+ .get_group_pins = at91_get_group_pins,
+ .pin_dbg_show = at91_pin_dbg_show,
+ .dt_node_to_map = at91_dt_node_to_map,
+ .dt_free_map = at91_dt_free_map,
+};
+
+static void __iomem *pin_to_controller(struct at91_pinctrl *info,
+ unsigned int bank)
+{
+ return gpio_chips[bank]->regbase;
+}
+
+static inline int pin_to_bank(unsigned pin)
+{
+ return pin /= MAX_NB_GPIO_PER_BANK;
+}
+
+static unsigned pin_to_mask(unsigned int pin)
+{
+ return 1 << pin;
+}
+
+static unsigned two_bit_pin_value_shift_amount(unsigned int pin)
+{
+ /* return the shift value for a pin for "two bit" per pin registers,
+ * i.e. drive strength */
+ return 2*((pin >= MAX_NB_GPIO_PER_BANK/2)
+ ? pin - MAX_NB_GPIO_PER_BANK/2 : pin);
+}
+
+static unsigned sama5d3_get_drive_register(unsigned int pin)
+{
+ /* drive strength is split between two registers
+ * with two bits per pin */
+ return (pin >= MAX_NB_GPIO_PER_BANK/2)
+ ? SAMA5D3_PIO_DRIVER2 : SAMA5D3_PIO_DRIVER1;
+}
+
+static unsigned at91sam9x5_get_drive_register(unsigned int pin)
+{
+ /* drive strength is split between two registers
+ * with two bits per pin */
+ return (pin >= MAX_NB_GPIO_PER_BANK/2)
+ ? AT91SAM9X5_PIO_DRIVER2 : AT91SAM9X5_PIO_DRIVER1;
+}
+
+static void at91_mux_disable_interrupt(void __iomem *pio, unsigned mask)
+{
+ writel_relaxed(mask, pio + PIO_IDR);
+}
+
+static unsigned at91_mux_get_pullup(void __iomem *pio, unsigned pin)
+{
+ return !((readl_relaxed(pio + PIO_PUSR) >> pin) & 0x1);
+}
+
+static void at91_mux_set_pullup(void __iomem *pio, unsigned mask, bool on)
+{
+ if (on)
+ writel_relaxed(mask, pio + PIO_PPDDR);
+
+ writel_relaxed(mask, pio + (on ? PIO_PUER : PIO_PUDR));
+}
+
+static unsigned at91_mux_get_multidrive(void __iomem *pio, unsigned pin)
+{
+ return (readl_relaxed(pio + PIO_MDSR) >> pin) & 0x1;
+}
+
+static void at91_mux_set_multidrive(void __iomem *pio, unsigned mask, bool on)
+{
+ writel_relaxed(mask, pio + (on ? PIO_MDER : PIO_MDDR));
+}
+
+static void at91_mux_set_A_periph(void __iomem *pio, unsigned mask)
+{
+ writel_relaxed(mask, pio + PIO_ASR);
+}
+
+static void at91_mux_set_B_periph(void __iomem *pio, unsigned mask)
+{
+ writel_relaxed(mask, pio + PIO_BSR);
+}
+
+static void at91_mux_pio3_set_A_periph(void __iomem *pio, unsigned mask)
+{
+
+ writel_relaxed(readl_relaxed(pio + PIO_ABCDSR1) & ~mask,
+ pio + PIO_ABCDSR1);
+ writel_relaxed(readl_relaxed(pio + PIO_ABCDSR2) & ~mask,
+ pio + PIO_ABCDSR2);
+}
+
+static void at91_mux_pio3_set_B_periph(void __iomem *pio, unsigned mask)
+{
+ writel_relaxed(readl_relaxed(pio + PIO_ABCDSR1) | mask,
+ pio + PIO_ABCDSR1);
+ writel_relaxed(readl_relaxed(pio + PIO_ABCDSR2) & ~mask,
+ pio + PIO_ABCDSR2);
+}
+
+static void at91_mux_pio3_set_C_periph(void __iomem *pio, unsigned mask)
+{
+ writel_relaxed(readl_relaxed(pio + PIO_ABCDSR1) & ~mask, pio + PIO_ABCDSR1);
+ writel_relaxed(readl_relaxed(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2);
+}
+
+static void at91_mux_pio3_set_D_periph(void __iomem *pio, unsigned mask)
+{
+ writel_relaxed(readl_relaxed(pio + PIO_ABCDSR1) | mask, pio + PIO_ABCDSR1);
+ writel_relaxed(readl_relaxed(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2);
+}
+
+static enum at91_mux at91_mux_pio3_get_periph(void __iomem *pio, unsigned mask)
+{
+ unsigned select;
+
+ if (readl_relaxed(pio + PIO_PSR) & mask)
+ return AT91_MUX_GPIO;
+
+ select = !!(readl_relaxed(pio + PIO_ABCDSR1) & mask);
+ select |= (!!(readl_relaxed(pio + PIO_ABCDSR2) & mask) << 1);
+
+ return select + 1;
+}
+
+static enum at91_mux at91_mux_get_periph(void __iomem *pio, unsigned mask)
+{
+ unsigned select;
+
+ if (readl_relaxed(pio + PIO_PSR) & mask)
+ return AT91_MUX_GPIO;
+
+ select = readl_relaxed(pio + PIO_ABSR) & mask;
+
+ return select + 1;
+}
+
+static bool at91_mux_get_deglitch(void __iomem *pio, unsigned pin)
+{
+ return (readl_relaxed(pio + PIO_IFSR) >> pin) & 0x1;
+}
+
+static void at91_mux_set_deglitch(void __iomem *pio, unsigned mask, bool is_on)
+{
+ writel_relaxed(mask, pio + (is_on ? PIO_IFER : PIO_IFDR));
+}
+
+static bool at91_mux_pio3_get_deglitch(void __iomem *pio, unsigned pin)
+{
+ if ((readl_relaxed(pio + PIO_IFSR) >> pin) & 0x1)
+ return !((readl_relaxed(pio + PIO_IFSCSR) >> pin) & 0x1);
+
+ return false;
+}
+
+static void at91_mux_pio3_set_deglitch(void __iomem *pio, unsigned mask, bool is_on)
+{
+ if (is_on)
+ writel_relaxed(mask, pio + PIO_IFSCDR);
+ at91_mux_set_deglitch(pio, mask, is_on);
+}
+
+static bool at91_mux_pio3_get_debounce(void __iomem *pio, unsigned pin, u32 *div)
+{
+ *div = readl_relaxed(pio + PIO_SCDR);
+
+ return ((readl_relaxed(pio + PIO_IFSR) >> pin) & 0x1) &&
+ ((readl_relaxed(pio + PIO_IFSCSR) >> pin) & 0x1);
+}
+
+static void at91_mux_pio3_set_debounce(void __iomem *pio, unsigned mask,
+ bool is_on, u32 div)
+{
+ if (is_on) {
+ writel_relaxed(mask, pio + PIO_IFSCER);
+ writel_relaxed(div & PIO_SCDR_DIV, pio + PIO_SCDR);
+ writel_relaxed(mask, pio + PIO_IFER);
+ } else
+ writel_relaxed(mask, pio + PIO_IFSCDR);
+}
+
+static bool at91_mux_pio3_get_pulldown(void __iomem *pio, unsigned pin)
+{
+ return !((readl_relaxed(pio + PIO_PPDSR) >> pin) & 0x1);
+}
+
+static void at91_mux_pio3_set_pulldown(void __iomem *pio, unsigned mask, bool is_on)
+{
+ if (is_on)
+ writel_relaxed(mask, pio + PIO_PUDR);
+
+ writel_relaxed(mask, pio + (is_on ? PIO_PPDER : PIO_PPDDR));
+}
+
+static void at91_mux_pio3_disable_schmitt_trig(void __iomem *pio, unsigned mask)
+{
+ writel_relaxed(readl_relaxed(pio + PIO_SCHMITT) | mask, pio + PIO_SCHMITT);
+}
+
+static bool at91_mux_pio3_get_schmitt_trig(void __iomem *pio, unsigned pin)
+{
+ return (readl_relaxed(pio + PIO_SCHMITT) >> pin) & 0x1;
+}
+
+static inline u32 read_drive_strength(void __iomem *reg, unsigned pin)
+{
+ unsigned tmp = readl_relaxed(reg);
+
+ tmp = tmp >> two_bit_pin_value_shift_amount(pin);
+
+ return tmp & DRIVE_STRENGTH_MASK;
+}
+
+static unsigned at91_mux_sama5d3_get_drivestrength(void __iomem *pio,
+ unsigned pin)
+{
+ unsigned tmp = read_drive_strength(pio +
+ sama5d3_get_drive_register(pin), pin);
+
+ /* SAMA5 strength is 1:1 with our defines,
+ * except 0 is equivalent to low per datasheet */
+ if (!tmp)
+ tmp = DRIVE_STRENGTH_LOW;
+
+ return tmp;
+}
+
+static unsigned at91_mux_sam9x5_get_drivestrength(void __iomem *pio,
+ unsigned pin)
+{
+ unsigned tmp = read_drive_strength(pio +
+ at91sam9x5_get_drive_register(pin), pin);
+
+ /* strength is inverse in SAM9x5s hardware with the pinctrl defines
+ * hardware: 0 = hi, 1 = med, 2 = low, 3 = rsvd */
+ tmp = DRIVE_STRENGTH_HI - tmp;
+
+ return tmp;
+}
+
+static void set_drive_strength(void __iomem *reg, unsigned pin, u32 strength)
+{
+ unsigned tmp = readl_relaxed(reg);
+ unsigned shift = two_bit_pin_value_shift_amount(pin);
+
+ tmp &= ~(DRIVE_STRENGTH_MASK << shift);
+ tmp |= strength << shift;
+
+ writel_relaxed(tmp, reg);
+}
+
+static void at91_mux_sama5d3_set_drivestrength(void __iomem *pio, unsigned pin,
+ u32 setting)
+{
+ /* do nothing if setting is zero */
+ if (!setting)
+ return;
+
+ /* strength is 1 to 1 with setting for SAMA5 */
+ set_drive_strength(pio + sama5d3_get_drive_register(pin), pin, setting);
+}
+
+static void at91_mux_sam9x5_set_drivestrength(void __iomem *pio, unsigned pin,
+ u32 setting)
+{
+ /* do nothing if setting is zero */
+ if (!setting)
+ return;
+
+ /* strength is inverse on SAM9x5s with our defines
+ * 0 = hi, 1 = med, 2 = low, 3 = rsvd */
+ setting = DRIVE_STRENGTH_HI - setting;
+
+ set_drive_strength(pio + at91sam9x5_get_drive_register(pin), pin,
+ setting);
+}
+
+static struct at91_pinctrl_mux_ops at91rm9200_ops = {
+ .get_periph = at91_mux_get_periph,
+ .mux_A_periph = at91_mux_set_A_periph,
+ .mux_B_periph = at91_mux_set_B_periph,
+ .get_deglitch = at91_mux_get_deglitch,
+ .set_deglitch = at91_mux_set_deglitch,
+ .irq_type = gpio_irq_type,
+};
+
+static struct at91_pinctrl_mux_ops at91sam9x5_ops = {
+ .get_periph = at91_mux_pio3_get_periph,
+ .mux_A_periph = at91_mux_pio3_set_A_periph,
+ .mux_B_periph = at91_mux_pio3_set_B_periph,
+ .mux_C_periph = at91_mux_pio3_set_C_periph,
+ .mux_D_periph = at91_mux_pio3_set_D_periph,
+ .get_deglitch = at91_mux_pio3_get_deglitch,
+ .set_deglitch = at91_mux_pio3_set_deglitch,
+ .get_debounce = at91_mux_pio3_get_debounce,
+ .set_debounce = at91_mux_pio3_set_debounce,
+ .get_pulldown = at91_mux_pio3_get_pulldown,
+ .set_pulldown = at91_mux_pio3_set_pulldown,
+ .get_schmitt_trig = at91_mux_pio3_get_schmitt_trig,
+ .disable_schmitt_trig = at91_mux_pio3_disable_schmitt_trig,
+ .get_drivestrength = at91_mux_sam9x5_get_drivestrength,
+ .set_drivestrength = at91_mux_sam9x5_set_drivestrength,
+ .irq_type = alt_gpio_irq_type,
+};
+
+static struct at91_pinctrl_mux_ops sama5d3_ops = {
+ .get_periph = at91_mux_pio3_get_periph,
+ .mux_A_periph = at91_mux_pio3_set_A_periph,
+ .mux_B_periph = at91_mux_pio3_set_B_periph,
+ .mux_C_periph = at91_mux_pio3_set_C_periph,
+ .mux_D_periph = at91_mux_pio3_set_D_periph,
+ .get_deglitch = at91_mux_pio3_get_deglitch,
+ .set_deglitch = at91_mux_pio3_set_deglitch,
+ .get_debounce = at91_mux_pio3_get_debounce,
+ .set_debounce = at91_mux_pio3_set_debounce,
+ .get_pulldown = at91_mux_pio3_get_pulldown,
+ .set_pulldown = at91_mux_pio3_set_pulldown,
+ .get_schmitt_trig = at91_mux_pio3_get_schmitt_trig,
+ .disable_schmitt_trig = at91_mux_pio3_disable_schmitt_trig,
+ .get_drivestrength = at91_mux_sama5d3_get_drivestrength,
+ .set_drivestrength = at91_mux_sama5d3_set_drivestrength,
+ .irq_type = alt_gpio_irq_type,
+};
+
+static void at91_pin_dbg(const struct device *dev, const struct at91_pmx_pin *pin)
+{
+ if (pin->mux) {
+ dev_dbg(dev, "pio%c%d configured as periph%c with conf = 0x%lx\n",
+ pin->bank + 'A', pin->pin, pin->mux - 1 + 'A', pin->conf);
+ } else {
+ dev_dbg(dev, "pio%c%d configured as gpio with conf = 0x%lx\n",
+ pin->bank + 'A', pin->pin, pin->conf);
+ }
+}
+
+static int pin_check_config(struct at91_pinctrl *info, const char *name,
+ int index, const struct at91_pmx_pin *pin)
+{
+ int mux;
+
+ /* check if it's a valid config */
+ if (pin->bank >= gpio_banks) {
+ dev_err(info->dev, "%s: pin conf %d bank_id %d >= nbanks %d\n",
+ name, index, pin->bank, gpio_banks);
+ return -EINVAL;
+ }
+
+ if (!gpio_chips[pin->bank]) {
+ dev_err(info->dev, "%s: pin conf %d bank_id %d not enabled\n",
+ name, index, pin->bank);
+ return -ENXIO;
+ }
+
+ if (pin->pin >= MAX_NB_GPIO_PER_BANK) {
+ dev_err(info->dev, "%s: pin conf %d pin_bank_id %d >= %d\n",
+ name, index, pin->pin, MAX_NB_GPIO_PER_BANK);
+ return -EINVAL;
+ }
+
+ if (!pin->mux)
+ return 0;
+
+ mux = pin->mux - 1;
+
+ if (mux >= info->nmux) {
+ dev_err(info->dev, "%s: pin conf %d mux_id %d >= nmux %d\n",
+ name, index, mux, info->nmux);
+ return -EINVAL;
+ }
+
+ if (!(info->mux_mask[pin->bank * info->nmux + mux] & 1 << pin->pin)) {
+ dev_err(info->dev, "%s: pin conf %d mux_id %d not supported for pio%c%d\n",
+ name, index, mux, pin->bank + 'A', pin->pin);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void at91_mux_gpio_disable(void __iomem *pio, unsigned mask)
+{
+ writel_relaxed(mask, pio + PIO_PDR);
+}
+
+static void at91_mux_gpio_enable(void __iomem *pio, unsigned mask, bool input)
+{
+ writel_relaxed(mask, pio + PIO_PER);
+ writel_relaxed(mask, pio + (input ? PIO_ODR : PIO_OER));
+}
+
+static int at91_pmx_set(struct pinctrl_dev *pctldev, unsigned selector,
+ unsigned group)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+ const struct at91_pmx_pin *pins_conf = info->groups[group].pins_conf;
+ const struct at91_pmx_pin *pin;
+ uint32_t npins = info->groups[group].npins;
+ int i, ret;
+ unsigned mask;
+ void __iomem *pio;
+
+ dev_dbg(info->dev, "enable function %s group %s\n",
+ info->functions[selector].name, info->groups[group].name);
+
+ /* first check that all the pins of the group are valid with a valid
+ * parameter */
+ for (i = 0; i < npins; i++) {
+ pin = &pins_conf[i];
+ ret = pin_check_config(info, info->groups[group].name, i, pin);
+ if (ret)
+ return ret;
+ }
+
+ for (i = 0; i < npins; i++) {
+ pin = &pins_conf[i];
+ at91_pin_dbg(info->dev, pin);
+ pio = pin_to_controller(info, pin->bank);
+ mask = pin_to_mask(pin->pin);
+ at91_mux_disable_interrupt(pio, mask);
+ switch (pin->mux) {
+ case AT91_MUX_GPIO:
+ at91_mux_gpio_enable(pio, mask, 1);
+ break;
+ case AT91_MUX_PERIPH_A:
+ info->ops->mux_A_periph(pio, mask);
+ break;
+ case AT91_MUX_PERIPH_B:
+ info->ops->mux_B_periph(pio, mask);
+ break;
+ case AT91_MUX_PERIPH_C:
+ if (!info->ops->mux_C_periph)
+ return -EINVAL;
+ info->ops->mux_C_periph(pio, mask);
+ break;
+ case AT91_MUX_PERIPH_D:
+ if (!info->ops->mux_D_periph)
+ return -EINVAL;
+ info->ops->mux_D_periph(pio, mask);
+ break;
+ }
+ if (pin->mux)
+ at91_mux_gpio_disable(pio, mask);
+ }
+
+ return 0;
+}
+
+static int at91_pmx_get_funcs_count(struct pinctrl_dev *pctldev)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+
+ return info->nfunctions;
+}
+
+static const char *at91_pmx_get_func_name(struct pinctrl_dev *pctldev,
+ unsigned selector)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+
+ return info->functions[selector].name;
+}
+
+static int at91_pmx_get_groups(struct pinctrl_dev *pctldev, unsigned selector,
+ const char * const **groups,
+ unsigned * const num_groups)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = info->functions[selector].groups;
+ *num_groups = info->functions[selector].ngroups;
+
+ return 0;
+}
+
+static int at91_gpio_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned offset)
+{
+ struct at91_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
+ struct at91_gpio_chip *at91_chip;
+ struct gpio_chip *chip;
+ unsigned mask;
+
+ if (!range) {
+ dev_err(npct->dev, "invalid range\n");
+ return -EINVAL;
+ }
+ if (!range->gc) {
+ dev_err(npct->dev, "missing GPIO chip in range\n");
+ return -EINVAL;
+ }
+ chip = range->gc;
+ at91_chip = container_of(chip, struct at91_gpio_chip, chip);
+
+ dev_dbg(npct->dev, "enable pin %u as GPIO\n", offset);
+
+ mask = 1 << (offset - chip->base);
+
+ dev_dbg(npct->dev, "enable pin %u as PIO%c%d 0x%x\n",
+ offset, 'A' + range->id, offset - chip->base, mask);
+
+ writel_relaxed(mask, at91_chip->regbase + PIO_PER);
+
+ return 0;
+}
+
+static void at91_gpio_disable_free(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned offset)
+{
+ struct at91_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
+
+ dev_dbg(npct->dev, "disable pin %u as GPIO\n", offset);
+ /* Set the pin to some default state, GPIO is usually default */
+}
+
+static const struct pinmux_ops at91_pmx_ops = {
+ .get_functions_count = at91_pmx_get_funcs_count,
+ .get_function_name = at91_pmx_get_func_name,
+ .get_function_groups = at91_pmx_get_groups,
+ .set_mux = at91_pmx_set,
+ .gpio_request_enable = at91_gpio_request_enable,
+ .gpio_disable_free = at91_gpio_disable_free,
+};
+
+static int at91_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned pin_id, unsigned long *config)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+ void __iomem *pio;
+ unsigned pin;
+ int div;
+
+ *config = 0;
+ dev_dbg(info->dev, "%s:%d, pin_id=%d", __func__, __LINE__, pin_id);
+ pio = pin_to_controller(info, pin_to_bank(pin_id));
+ pin = pin_id % MAX_NB_GPIO_PER_BANK;
+
+ if (at91_mux_get_multidrive(pio, pin))
+ *config |= MULTI_DRIVE;
+
+ if (at91_mux_get_pullup(pio, pin))
+ *config |= PULL_UP;
+
+ if (info->ops->get_deglitch && info->ops->get_deglitch(pio, pin))
+ *config |= DEGLITCH;
+ if (info->ops->get_debounce && info->ops->get_debounce(pio, pin, &div))
+ *config |= DEBOUNCE | (div << DEBOUNCE_VAL_SHIFT);
+ if (info->ops->get_pulldown && info->ops->get_pulldown(pio, pin))
+ *config |= PULL_DOWN;
+ if (info->ops->get_schmitt_trig && info->ops->get_schmitt_trig(pio, pin))
+ *config |= DIS_SCHMIT;
+ if (info->ops->get_drivestrength)
+ *config |= (info->ops->get_drivestrength(pio, pin)
+ << DRIVE_STRENGTH_SHIFT);
+
+ return 0;
+}
+
+static int at91_pinconf_set(struct pinctrl_dev *pctldev,
+ unsigned pin_id, unsigned long *configs,
+ unsigned num_configs)
+{
+ struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+ unsigned mask;
+ void __iomem *pio;
+ int i;
+ unsigned long config;
+ unsigned pin;
+
+ for (i = 0; i < num_configs; i++) {
+ config = configs[i];
+
+ dev_dbg(info->dev,
+ "%s:%d, pin_id=%d, config=0x%lx",
+ __func__, __LINE__, pin_id, config);
+ pio = pin_to_controller(info, pin_to_bank(pin_id));
+ pin = pin_id % MAX_NB_GPIO_PER_BANK;
+ mask = pin_to_mask(pin);
+
+ if (config & PULL_UP && config & PULL_DOWN)
+ return -EINVAL;
+
+ at91_mux_set_pullup(pio, mask, config & PULL_UP);
+ at91_mux_set_multidrive(pio, mask, config & MULTI_DRIVE);
+ if (info->ops->set_deglitch)
+ info->ops->set_deglitch(pio, mask, config & DEGLITCH);
+ if (info->ops->set_debounce)
+ info->ops->set_debounce(pio, mask, config & DEBOUNCE,
+ (config & DEBOUNCE_VAL) >> DEBOUNCE_VAL_SHIFT);
+ if (info->ops->set_pulldown)
+ info->ops->set_pulldown(pio, mask, config & PULL_DOWN);
+ if (info->ops->disable_schmitt_trig && config & DIS_SCHMIT)
+ info->ops->disable_schmitt_trig(pio, mask);
+ if (info->ops->set_drivestrength)
+ info->ops->set_drivestrength(pio, pin,
+ (config & DRIVE_STRENGTH)
+ >> DRIVE_STRENGTH_SHIFT);
+
+ } /* for each config */
+
+ return 0;
+}
+
+#define DBG_SHOW_FLAG(flag) do { \
+ if (config & flag) { \
+ if (num_conf) \
+ seq_puts(s, "|"); \
+ seq_puts(s, #flag); \
+ num_conf++; \
+ } \
+} while (0)
+
+#define DBG_SHOW_FLAG_MASKED(mask,flag) do { \
+ if ((config & mask) == flag) { \
+ if (num_conf) \
+ seq_puts(s, "|"); \
+ seq_puts(s, #flag); \
+ num_conf++; \
+ } \
+} while (0)
+
+static void at91_pinconf_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s, unsigned pin_id)
+{
+ unsigned long config;
+ int val, num_conf = 0;
+
+ at91_pinconf_get(pctldev, pin_id, &config);
+
+ DBG_SHOW_FLAG(MULTI_DRIVE);
+ DBG_SHOW_FLAG(PULL_UP);
+ DBG_SHOW_FLAG(PULL_DOWN);
+ DBG_SHOW_FLAG(DIS_SCHMIT);
+ DBG_SHOW_FLAG(DEGLITCH);
+ DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_LOW);
+ DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_MED);
+ DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_HI);
+ DBG_SHOW_FLAG(DEBOUNCE);
+ if (config & DEBOUNCE) {
+ val = config >> DEBOUNCE_VAL_SHIFT;
+ seq_printf(s, "(%d)", val);
+ }
+
+ return;
+}
+
+static void at91_pinconf_group_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s, unsigned group)
+{
+}
+
+static const struct pinconf_ops at91_pinconf_ops = {
+ .pin_config_get = at91_pinconf_get,
+ .pin_config_set = at91_pinconf_set,
+ .pin_config_dbg_show = at91_pinconf_dbg_show,
+ .pin_config_group_dbg_show = at91_pinconf_group_dbg_show,
+};
+
+static struct pinctrl_desc at91_pinctrl_desc = {
+ .pctlops = &at91_pctrl_ops,
+ .pmxops = &at91_pmx_ops,
+ .confops = &at91_pinconf_ops,
+ .owner = THIS_MODULE,
+};
+
+static const char *gpio_compat = "atmel,at91rm9200-gpio";
+
+static void at91_pinctrl_child_count(struct at91_pinctrl *info,
+ struct device_node *np)
+{
+ struct device_node *child;
+
+ for_each_child_of_node(np, child) {
+ if (of_device_is_compatible(child, gpio_compat)) {
+ if (of_device_is_available(child))
+ info->nactive_banks++;
+ } else {
+ info->nfunctions++;
+ info->ngroups += of_get_child_count(child);
+ }
+ }
+}
+
+static int at91_pinctrl_mux_mask(struct at91_pinctrl *info,
+ struct device_node *np)
+{
+ int ret = 0;
+ int size;
+ const __be32 *list;
+
+ list = of_get_property(np, "atmel,mux-mask", &size);
+ if (!list) {
+ dev_err(info->dev, "can not read the mux-mask of %d\n", size);
+ return -EINVAL;
+ }
+
+ size /= sizeof(*list);
+ if (!size || size % gpio_banks) {
+ dev_err(info->dev, "wrong mux mask array should be by %d\n", gpio_banks);
+ return -EINVAL;
+ }
+ info->nmux = size / gpio_banks;
+
+ info->mux_mask = devm_kzalloc(info->dev, sizeof(u32) * size, GFP_KERNEL);
+ if (!info->mux_mask) {
+ dev_err(info->dev, "could not alloc mux_mask\n");
+ return -ENOMEM;
+ }
+
+ ret = of_property_read_u32_array(np, "atmel,mux-mask",
+ info->mux_mask, size);
+ if (ret)
+ dev_err(info->dev, "can not read the mux-mask of %d\n", size);
+ return ret;
+}
+
+static int at91_pinctrl_parse_groups(struct device_node *np,
+ struct at91_pin_group *grp,
+ struct at91_pinctrl *info, u32 index)
+{
+ struct at91_pmx_pin *pin;
+ int size;
+ const __be32 *list;
+ int i, j;
+
+ dev_dbg(info->dev, "group(%d): %s\n", index, np->name);
+
+ /* Initialise group */
+ grp->name = np->name;
+
+ /*
+ * the binding format is atmel,pins = <bank pin mux CONFIG ...>,
+ * do sanity check and calculate pins number
+ */
+ list = of_get_property(np, "atmel,pins", &size);
+ /* we do not check return since it's safe node passed down */
+ size /= sizeof(*list);
+ if (!size || size % 4) {
+ dev_err(info->dev, "wrong pins number or pins and configs should be by 4\n");
+ return -EINVAL;
+ }
+
+ grp->npins = size / 4;
+ pin = grp->pins_conf = devm_kzalloc(info->dev, grp->npins * sizeof(struct at91_pmx_pin),
+ GFP_KERNEL);
+ grp->pins = devm_kzalloc(info->dev, grp->npins * sizeof(unsigned int),
+ GFP_KERNEL);
+ if (!grp->pins_conf || !grp->pins)
+ return -ENOMEM;
+
+ for (i = 0, j = 0; i < size; i += 4, j++) {
+ pin->bank = be32_to_cpu(*list++);
+ pin->pin = be32_to_cpu(*list++);
+ grp->pins[j] = pin->bank * MAX_NB_GPIO_PER_BANK + pin->pin;
+ pin->mux = be32_to_cpu(*list++);
+ pin->conf = be32_to_cpu(*list++);
+
+ at91_pin_dbg(info->dev, pin);
+ pin++;
+ }
+
+ return 0;
+}
+
+static int at91_pinctrl_parse_functions(struct device_node *np,
+ struct at91_pinctrl *info, u32 index)
+{
+ struct device_node *child;
+ struct at91_pmx_func *func;
+ struct at91_pin_group *grp;
+ int ret;
+ static u32 grp_index;
+ u32 i = 0;
+
+ dev_dbg(info->dev, "parse function(%d): %s\n", index, np->name);
+
+ func = &info->functions[index];
+
+ /* Initialise function */
+ func->name = np->name;
+ func->ngroups = of_get_child_count(np);
+ if (func->ngroups == 0) {
+ dev_err(info->dev, "no groups defined\n");
+ return -EINVAL;
+ }
+ func->groups = devm_kzalloc(info->dev,
+ func->ngroups * sizeof(char *), GFP_KERNEL);
+ if (!func->groups)
+ return -ENOMEM;
+
+ for_each_child_of_node(np, child) {
+ func->groups[i] = child->name;
+ grp = &info->groups[grp_index++];
+ ret = at91_pinctrl_parse_groups(child, grp, info, i++);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct of_device_id at91_pinctrl_of_match[] = {
+ { .compatible = "atmel,sama5d3-pinctrl", .data = &sama5d3_ops },
+ { .compatible = "atmel,at91sam9x5-pinctrl", .data = &at91sam9x5_ops },
+ { .compatible = "atmel,at91rm9200-pinctrl", .data = &at91rm9200_ops },
+ { /* sentinel */ }
+};
+
+static int at91_pinctrl_probe_dt(struct platform_device *pdev,
+ struct at91_pinctrl *info)
+{
+ int ret = 0;
+ int i, j;
+ uint32_t *tmp;
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *child;
+
+ if (!np)
+ return -ENODEV;
+
+ info->dev = &pdev->dev;
+ info->ops = (struct at91_pinctrl_mux_ops *)
+ of_match_device(at91_pinctrl_of_match, &pdev->dev)->data;
+ at91_pinctrl_child_count(info, np);
+
+ if (gpio_banks < 1) {
+ dev_err(&pdev->dev, "you need to specify at least one gpio-controller\n");
+ return -EINVAL;
+ }
+
+ ret = at91_pinctrl_mux_mask(info, np);
+ if (ret)
+ return ret;
+
+ dev_dbg(&pdev->dev, "nmux = %d\n", info->nmux);
+
+ dev_dbg(&pdev->dev, "mux-mask\n");
+ tmp = info->mux_mask;
+ for (i = 0; i < gpio_banks; i++) {
+ for (j = 0; j < info->nmux; j++, tmp++) {
+ dev_dbg(&pdev->dev, "%d:%d\t0x%x\n", i, j, tmp[0]);
+ }
+ }
+
+ dev_dbg(&pdev->dev, "nfunctions = %d\n", info->nfunctions);
+ dev_dbg(&pdev->dev, "ngroups = %d\n", info->ngroups);
+ info->functions = devm_kzalloc(&pdev->dev, info->nfunctions * sizeof(struct at91_pmx_func),
+ GFP_KERNEL);
+ if (!info->functions)
+ return -ENOMEM;
+
+ info->groups = devm_kzalloc(&pdev->dev, info->ngroups * sizeof(struct at91_pin_group),
+ GFP_KERNEL);
+ if (!info->groups)
+ return -ENOMEM;
+
+ dev_dbg(&pdev->dev, "nbanks = %d\n", gpio_banks);
+ dev_dbg(&pdev->dev, "nfunctions = %d\n", info->nfunctions);
+ dev_dbg(&pdev->dev, "ngroups = %d\n", info->ngroups);
+
+ i = 0;
+
+ for_each_child_of_node(np, child) {
+ if (of_device_is_compatible(child, gpio_compat))
+ continue;
+ ret = at91_pinctrl_parse_functions(child, info, i++);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to parse function\n");
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int at91_pinctrl_probe(struct platform_device *pdev)
+{
+ struct at91_pinctrl *info;
+ struct pinctrl_pin_desc *pdesc;
+ int ret, i, j, k, ngpio_chips_enabled = 0;
+
+ info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ ret = at91_pinctrl_probe_dt(pdev, info);
+ if (ret)
+ return ret;
+
+ /*
+ * We need all the GPIO drivers to probe FIRST, or we will not be able
+ * to obtain references to the struct gpio_chip * for them, and we
+ * need this to proceed.
+ */
+ for (i = 0; i < gpio_banks; i++)
+ if (gpio_chips[i])
+ ngpio_chips_enabled++;
+
+ if (ngpio_chips_enabled < info->nactive_banks) {
+ dev_warn(&pdev->dev,
+ "All GPIO chips are not registered yet (%d/%d)\n",
+ ngpio_chips_enabled, info->nactive_banks);
+ devm_kfree(&pdev->dev, info);
+ return -EPROBE_DEFER;
+ }
+
+ at91_pinctrl_desc.name = dev_name(&pdev->dev);
+ at91_pinctrl_desc.npins = gpio_banks * MAX_NB_GPIO_PER_BANK;
+ at91_pinctrl_desc.pins = pdesc =
+ devm_kzalloc(&pdev->dev, sizeof(*pdesc) * at91_pinctrl_desc.npins, GFP_KERNEL);
+
+ if (!at91_pinctrl_desc.pins)
+ return -ENOMEM;
+
+ for (i = 0, k = 0; i < gpio_banks; i++) {
+ for (j = 0; j < MAX_NB_GPIO_PER_BANK; j++, k++) {
+ pdesc->number = k;
+ pdesc->name = kasprintf(GFP_KERNEL, "pio%c%d", i + 'A', j);
+ pdesc++;
+ }
+ }
+
+ platform_set_drvdata(pdev, info);
+ info->pctl = pinctrl_register(&at91_pinctrl_desc, &pdev->dev, info);
+
+ if (!info->pctl) {
+ dev_err(&pdev->dev, "could not register AT91 pinctrl driver\n");
+ return -EINVAL;
+ }
+
+ /* We will handle a range of GPIO pins */
+ for (i = 0; i < gpio_banks; i++)
+ if (gpio_chips[i])
+ pinctrl_add_gpio_range(info->pctl, &gpio_chips[i]->range);
+
+ dev_info(&pdev->dev, "initialized AT91 pinctrl driver\n");
+
+ return 0;
+}
+
+static int at91_pinctrl_remove(struct platform_device *pdev)
+{
+ struct at91_pinctrl *info = platform_get_drvdata(pdev);
+
+ pinctrl_unregister(info->pctl);
+
+ return 0;
+}
+
+static int at91_gpio_request(struct gpio_chip *chip, unsigned offset)
+{
+ /*
+ * Map back to global GPIO space and request muxing, the direction
+ * parameter does not matter for this controller.
+ */
+ int gpio = chip->base + offset;
+ int bank = chip->base / chip->ngpio;
+
+ dev_dbg(chip->dev, "%s:%d pio%c%d(%d)\n", __func__, __LINE__,
+ 'A' + bank, offset, gpio);
+
+ return pinctrl_request_gpio(gpio);
+}
+
+static void at91_gpio_free(struct gpio_chip *chip, unsigned offset)
+{
+ int gpio = chip->base + offset;
+
+ pinctrl_free_gpio(gpio);
+}
+
+static int at91_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
+{
+ struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << offset;
+ u32 osr;
+
+ osr = readl_relaxed(pio + PIO_OSR);
+ return !(osr & mask);
+}
+
+static int at91_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << offset;
+
+ writel_relaxed(mask, pio + PIO_ODR);
+ return 0;
+}
+
+static int at91_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << offset;
+ u32 pdsr;
+
+ pdsr = readl_relaxed(pio + PIO_PDSR);
+ return (pdsr & mask) != 0;
+}
+
+static void at91_gpio_set(struct gpio_chip *chip, unsigned offset,
+ int val)
+{
+ struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << offset;
+
+ writel_relaxed(mask, pio + (val ? PIO_SODR : PIO_CODR));
+}
+
+static int at91_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+ int val)
+{
+ struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << offset;
+
+ writel_relaxed(mask, pio + (val ? PIO_SODR : PIO_CODR));
+ writel_relaxed(mask, pio + PIO_OER);
+
+ return 0;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void at91_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ enum at91_mux mode;
+ int i;
+ struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
+ void __iomem *pio = at91_gpio->regbase;
+
+ for (i = 0; i < chip->ngpio; i++) {
+ unsigned mask = pin_to_mask(i);
+ const char *gpio_label;
+
+ gpio_label = gpiochip_is_requested(chip, i);
+ if (!gpio_label)
+ continue;
+ mode = at91_gpio->ops->get_periph(pio, mask);
+ seq_printf(s, "[%s] GPIO%s%d: ",
+ gpio_label, chip->label, i);
+ if (mode == AT91_MUX_GPIO) {
+ seq_printf(s, "[gpio] ");
+ seq_printf(s, "%s ",
+ readl_relaxed(pio + PIO_OSR) & mask ?
+ "output" : "input");
+ seq_printf(s, "%s\n",
+ readl_relaxed(pio + PIO_PDSR) & mask ?
+ "set" : "clear");
+ } else {
+ seq_printf(s, "[periph %c]\n",
+ mode + 'A' - 1);
+ }
+ }
+}
+#else
+#define at91_gpio_dbg_show NULL
+#endif
+
+/* Several AIC controller irqs are dispatched through this GPIO handler.
+ * To use any AT91_PIN_* as an externally triggered IRQ, first call
+ * at91_set_gpio_input() then maybe enable its glitch filter.
+ * Then just request_irq() with the pin ID; it works like any ARM IRQ
+ * handler.
+ * First implementation always triggers on rising and falling edges
+ * whereas the newer PIO3 can be additionally configured to trigger on
+ * level, edge with any polarity.
+ *
+ * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after
+ * configuring them with at91_set_a_periph() or at91_set_b_periph().
+ * IRQ0..IRQ6 should be configurable, e.g. level vs edge triggering.
+ */
+
+static void gpio_irq_mask(struct irq_data *d)
+{
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << d->hwirq;
+
+ if (pio)
+ writel_relaxed(mask, pio + PIO_IDR);
+}
+
+static void gpio_irq_unmask(struct irq_data *d)
+{
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << d->hwirq;
+
+ if (pio)
+ writel_relaxed(mask, pio + PIO_IER);
+}
+
+static int gpio_irq_type(struct irq_data *d, unsigned type)
+{
+ switch (type) {
+ case IRQ_TYPE_NONE:
+ case IRQ_TYPE_EDGE_BOTH:
+ return 0;
+ default:
+ return -EINVAL;
+ }
+}
+
+/* Alternate irq type for PIO3 support */
+static int alt_gpio_irq_type(struct irq_data *d, unsigned type)
+{
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << d->hwirq;
+
+ switch (type) {
+ case IRQ_TYPE_EDGE_RISING:
+ __irq_set_handler_locked(d->irq, handle_simple_irq);
+ writel_relaxed(mask, pio + PIO_ESR);
+ writel_relaxed(mask, pio + PIO_REHLSR);
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ __irq_set_handler_locked(d->irq, handle_simple_irq);
+ writel_relaxed(mask, pio + PIO_ESR);
+ writel_relaxed(mask, pio + PIO_FELLSR);
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ __irq_set_handler_locked(d->irq, handle_level_irq);
+ writel_relaxed(mask, pio + PIO_LSR);
+ writel_relaxed(mask, pio + PIO_FELLSR);
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ __irq_set_handler_locked(d->irq, handle_level_irq);
+ writel_relaxed(mask, pio + PIO_LSR);
+ writel_relaxed(mask, pio + PIO_REHLSR);
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ /*
+ * disable additional interrupt modes:
+ * fall back to default behavior
+ */
+ __irq_set_handler_locked(d->irq, handle_simple_irq);
+ writel_relaxed(mask, pio + PIO_AIMDR);
+ return 0;
+ case IRQ_TYPE_NONE:
+ default:
+ pr_warn("AT91: No type for irq %d\n", gpio_to_irq(d->irq));
+ return -EINVAL;
+ }
+
+ /* enable additional interrupt modes */
+ writel_relaxed(mask, pio + PIO_AIMER);
+
+ return 0;
+}
+
+static void gpio_irq_ack(struct irq_data *d)
+{
+ /* the interrupt is already cleared before by reading ISR */
+}
+
+static int gpio_irq_request_res(struct irq_data *d)
+{
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ unsigned pin = d->hwirq;
+ int ret;
+
+ ret = gpiochip_lock_as_irq(&at91_gpio->chip, pin);
+ if (ret)
+ dev_err(at91_gpio->chip.dev, "unable to lock pind %lu IRQ\n",
+ d->hwirq);
+
+ return ret;
+}
+
+static void gpio_irq_release_res(struct irq_data *d)
+{
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ unsigned pin = d->hwirq;
+
+ gpiochip_unlock_as_irq(&at91_gpio->chip, pin);
+}
+
+#ifdef CONFIG_PM
+
+static u32 wakeups[MAX_GPIO_BANKS];
+static u32 backups[MAX_GPIO_BANKS];
+
+static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
+{
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ unsigned bank = at91_gpio->pioc_idx;
+ unsigned mask = 1 << d->hwirq;
+
+ if (unlikely(bank >= MAX_GPIO_BANKS))
+ return -EINVAL;
+
+ if (state)
+ wakeups[bank] |= mask;
+ else
+ wakeups[bank] &= ~mask;
+
+ irq_set_irq_wake(at91_gpio->pioc_virq, state);
+
+ return 0;
+}
+
+void at91_pinctrl_gpio_suspend(void)
+{
+ int i;
+
+ for (i = 0; i < gpio_banks; i++) {
+ void __iomem *pio;
+
+ if (!gpio_chips[i])
+ continue;
+
+ pio = gpio_chips[i]->regbase;
+
+ backups[i] = readl_relaxed(pio + PIO_IMR);
+ writel_relaxed(backups[i], pio + PIO_IDR);
+ writel_relaxed(wakeups[i], pio + PIO_IER);
+
+ if (!wakeups[i])
+ clk_disable_unprepare(gpio_chips[i]->clock);
+ else
+ printk(KERN_DEBUG "GPIO-%c may wake for %08x\n",
+ 'A'+i, wakeups[i]);
+ }
+}
+
+void at91_pinctrl_gpio_resume(void)
+{
+ int i;
+
+ for (i = 0; i < gpio_banks; i++) {
+ void __iomem *pio;
+
+ if (!gpio_chips[i])
+ continue;
+
+ pio = gpio_chips[i]->regbase;
+
+ if (!wakeups[i])
+ clk_prepare_enable(gpio_chips[i]->clock);
+
+ writel_relaxed(wakeups[i], pio + PIO_IDR);
+ writel_relaxed(backups[i], pio + PIO_IER);
+ }
+}
+
+#else
+#define gpio_irq_set_wake NULL
+#endif /* CONFIG_PM */
+
+static struct irq_chip gpio_irqchip = {
+ .name = "GPIO",
+ .irq_ack = gpio_irq_ack,
+ .irq_request_resources = gpio_irq_request_res,
+ .irq_release_resources = gpio_irq_release_res,
+ .irq_disable = gpio_irq_mask,
+ .irq_mask = gpio_irq_mask,
+ .irq_unmask = gpio_irq_unmask,
+ /* .irq_set_type is set dynamically */
+ .irq_set_wake = gpio_irq_set_wake,
+};
+
+static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
+{
+ struct irq_chip *chip = irq_get_chip(irq);
+ struct gpio_chip *gpio_chip = irq_desc_get_handler_data(desc);
+ struct at91_gpio_chip *at91_gpio = container_of(gpio_chip,
+ struct at91_gpio_chip, chip);
+
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned long isr;
+ int n;
+
+ chained_irq_enter(chip, desc);
+ for (;;) {
+ /* Reading ISR acks pending (edge triggered) GPIO interrupts.
+ * When there are none pending, we're finished unless we need
+ * to process multiple banks (like ID_PIOCDE on sam9263).
+ */
+ isr = readl_relaxed(pio + PIO_ISR) & readl_relaxed(pio + PIO_IMR);
+ if (!isr) {
+ if (!at91_gpio->next)
+ break;
+ at91_gpio = at91_gpio->next;
+ pio = at91_gpio->regbase;
+ gpio_chip = &at91_gpio->chip;
+ continue;
+ }
+
+ for_each_set_bit(n, &isr, BITS_PER_LONG) {
+ generic_handle_irq(irq_find_mapping(
+ gpio_chip->irqdomain, n));
+ }
+ }
+ chained_irq_exit(chip, desc);
+ /* now it may re-trigger */
+}
+
+static int at91_gpio_of_irq_setup(struct platform_device *pdev,
+ struct at91_gpio_chip *at91_gpio)
+{
+ struct gpio_chip *gpiochip_prev = NULL;
+ struct at91_gpio_chip *prev = NULL;
+ struct irq_data *d = irq_get_irq_data(at91_gpio->pioc_virq);
+ int ret, i;
+
+ at91_gpio->pioc_hwirq = irqd_to_hwirq(d);
+
+ /* Setup proper .irq_set_type function */
+ gpio_irqchip.irq_set_type = at91_gpio->ops->irq_type;
+
+ /* Disable irqs of this PIO controller */
+ writel_relaxed(~0, at91_gpio->regbase + PIO_IDR);
+
+ /*
+ * Let the generic code handle this edge IRQ, the the chained
+ * handler will perform the actual work of handling the parent
+ * interrupt.
+ */
+ ret = gpiochip_irqchip_add(&at91_gpio->chip,
+ &gpio_irqchip,
+ 0,
+ handle_edge_irq,
+ IRQ_TYPE_EDGE_BOTH);
+ if (ret) {
+ dev_err(&pdev->dev, "at91_gpio.%d: Couldn't add irqchip to gpiochip.\n",
+ at91_gpio->pioc_idx);
+ return ret;
+ }
+
+ /* The top level handler handles one bank of GPIOs, except
+ * on some SoC it can handle up to three...
+ * We only set up the handler for the first of the list.
+ */
+ gpiochip_prev = irq_get_handler_data(at91_gpio->pioc_virq);
+ if (!gpiochip_prev) {
+ /* Then register the chain on the parent IRQ */
+ gpiochip_set_chained_irqchip(&at91_gpio->chip,
+ &gpio_irqchip,
+ at91_gpio->pioc_virq,
+ gpio_irq_handler);
+ return 0;
+ }
+
+ prev = container_of(gpiochip_prev, struct at91_gpio_chip, chip);
+
+ /* we can only have 2 banks before */
+ for (i = 0; i < 2; i++) {
+ if (prev->next) {
+ prev = prev->next;
+ } else {
+ prev->next = at91_gpio;
+ return 0;
+ }
+ }
+
+ return -EINVAL;
+}
+
+/* This structure is replicated for each GPIO block allocated at probe time */
+static struct gpio_chip at91_gpio_template = {
+ .request = at91_gpio_request,
+ .free = at91_gpio_free,
+ .get_direction = at91_gpio_get_direction,
+ .direction_input = at91_gpio_direction_input,
+ .get = at91_gpio_get,
+ .direction_output = at91_gpio_direction_output,
+ .set = at91_gpio_set,
+ .dbg_show = at91_gpio_dbg_show,
+ .can_sleep = false,
+ .ngpio = MAX_NB_GPIO_PER_BANK,
+};
+
+static const struct of_device_id at91_gpio_of_match[] = {
+ { .compatible = "atmel,at91sam9x5-gpio", .data = &at91sam9x5_ops, },
+ { .compatible = "atmel,at91rm9200-gpio", .data = &at91rm9200_ops },
+ { /* sentinel */ }
+};
+
+static int at91_gpio_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct resource *res;
+ struct at91_gpio_chip *at91_chip = NULL;
+ struct gpio_chip *chip;
+ struct pinctrl_gpio_range *range;
+ int ret = 0;
+ int irq, i;
+ int alias_idx = of_alias_get_id(np, "gpio");
+ uint32_t ngpio;
+ char **names;
+
+ BUG_ON(alias_idx >= ARRAY_SIZE(gpio_chips));
+ if (gpio_chips[alias_idx]) {
+ ret = -EBUSY;
+ goto err;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ ret = irq;
+ goto err;
+ }
+
+ at91_chip = devm_kzalloc(&pdev->dev, sizeof(*at91_chip), GFP_KERNEL);
+ if (!at91_chip) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ at91_chip->regbase = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(at91_chip->regbase)) {
+ ret = PTR_ERR(at91_chip->regbase);
+ goto err;
+ }
+
+ at91_chip->ops = (struct at91_pinctrl_mux_ops *)
+ of_match_device(at91_gpio_of_match, &pdev->dev)->data;
+ at91_chip->pioc_virq = irq;
+ at91_chip->pioc_idx = alias_idx;
+
+ at91_chip->clock = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(at91_chip->clock)) {
+ dev_err(&pdev->dev, "failed to get clock, ignoring.\n");
+ ret = PTR_ERR(at91_chip->clock);
+ goto err;
+ }
+
+ ret = clk_prepare(at91_chip->clock);
+ if (ret)
+ goto clk_prepare_err;
+
+ /* enable PIO controller's clock */
+ ret = clk_enable(at91_chip->clock);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable clock, ignoring.\n");
+ goto clk_enable_err;
+ }
+
+ at91_chip->chip = at91_gpio_template;
+
+ chip = &at91_chip->chip;
+ chip->of_node = np;
+ chip->label = dev_name(&pdev->dev);
+ chip->dev = &pdev->dev;
+ chip->owner = THIS_MODULE;
+ chip->base = alias_idx * MAX_NB_GPIO_PER_BANK;
+
+ if (!of_property_read_u32(np, "#gpio-lines", &ngpio)) {
+ if (ngpio >= MAX_NB_GPIO_PER_BANK)
+ pr_err("at91_gpio.%d, gpio-nb >= %d failback to %d\n",
+ alias_idx, MAX_NB_GPIO_PER_BANK, MAX_NB_GPIO_PER_BANK);
+ else
+ chip->ngpio = ngpio;
+ }
+
+ names = devm_kzalloc(&pdev->dev, sizeof(char *) * chip->ngpio,
+ GFP_KERNEL);
+
+ if (!names) {
+ ret = -ENOMEM;
+ goto clk_enable_err;
+ }
+
+ for (i = 0; i < chip->ngpio; i++)
+ names[i] = kasprintf(GFP_KERNEL, "pio%c%d", alias_idx + 'A', i);
+
+ chip->names = (const char *const *)names;
+
+ range = &at91_chip->range;
+ range->name = chip->label;
+ range->id = alias_idx;
+ range->pin_base = range->base = range->id * MAX_NB_GPIO_PER_BANK;
+
+ range->npins = chip->ngpio;
+ range->gc = chip;
+
+ ret = gpiochip_add(chip);
+ if (ret)
+ goto gpiochip_add_err;
+
+ gpio_chips[alias_idx] = at91_chip;
+ gpio_banks = max(gpio_banks, alias_idx + 1);
+
+ ret = at91_gpio_of_irq_setup(pdev, at91_chip);
+ if (ret)
+ goto irq_setup_err;
+
+ dev_info(&pdev->dev, "at address %p\n", at91_chip->regbase);
+
+ return 0;
+
+irq_setup_err:
+ gpiochip_remove(chip);
+gpiochip_add_err:
+ clk_disable(at91_chip->clock);
+clk_enable_err:
+ clk_unprepare(at91_chip->clock);
+clk_prepare_err:
+err:
+ dev_err(&pdev->dev, "Failure %i for GPIO %i\n", ret, alias_idx);
+
+ return ret;
+}
+
+static struct platform_driver at91_gpio_driver = {
+ .driver = {
+ .name = "gpio-at91",
+ .of_match_table = at91_gpio_of_match,
+ },
+ .probe = at91_gpio_probe,
+};
+
+static struct platform_driver at91_pinctrl_driver = {
+ .driver = {
+ .name = "pinctrl-at91",
+ .of_match_table = at91_pinctrl_of_match,
+ },
+ .probe = at91_pinctrl_probe,
+ .remove = at91_pinctrl_remove,
+};
+
+static int __init at91_pinctrl_init(void)
+{
+ int ret;
+
+ ret = platform_driver_register(&at91_gpio_driver);
+ if (ret)
+ return ret;
+ return platform_driver_register(&at91_pinctrl_driver);
+}
+arch_initcall(at91_pinctrl_init);
+
+static void __exit at91_pinctrl_exit(void)
+{
+ platform_driver_unregister(&at91_pinctrl_driver);
+}
+
+module_exit(at91_pinctrl_exit);
+MODULE_AUTHOR("Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>");
+MODULE_DESCRIPTION("Atmel AT91 pinctrl driver");
+MODULE_LICENSE("GPL v2");
Code Review / kvmfornfv.git / blobdiff