Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / drivers / net / fddi / Kconfig

diff --git a/kernel/drivers/net/fddi/Kconfig b/kernel/drivers/net/fddi/Kconfig
new file mode 100644 (file)
index 0000000..3a424c8
--- /dev/null
+++ b/kernel/drivers/net/fddi/Kconfig
@@ -0,0 +1,77 @@
+#
+# FDDI network device configuration
+#
+
+config FDDI
+       tristate "FDDI driver support"
+       depends on PCI || EISA || TC
+       ---help---
+         Fiber Distributed Data Interface is a high speed local area network
+         design; essentially a replacement for high speed Ethernet. FDDI can
+         run over copper or fiber. If you are connected to such a network and
+         want a driver for the FDDI card in your computer, say Y here (and
+         then also Y to the driver for your FDDI card, below). Most people
+         will say N.
+
+if FDDI
+
+config DEFXX
+       tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
+       depends on FDDI && (PCI || EISA || TC)
+       ---help---
+         This is support for the DIGITAL series of TURBOchannel (DEFTA),
+         EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
+         to a local FDDI network.
+
+         To compile this driver as a module, choose M here: the module
+         will be called defxx.  If unsure, say N.
+
+config DEFXX_MMIO
+       bool
+       prompt "Use MMIO instead of PIO" if PCI || EISA
+       depends on DEFXX
+       default n if PCI || EISA
+       default y
+       ---help---
+         This instructs the driver to use EISA or PCI memory-mapped I/O
+         (MMIO) as appropriate instead of programmed I/O ports (PIO).
+         Enabling this gives an improvement in processing time in parts
+         of the driver, but it may cause problems with EISA (DEFEA)
+         adapters.  TURBOchannel does not have the concept of I/O ports,
+         so MMIO is always used for these (DEFTA) adapters.
+
+         If unsure, say N.
+
+config SKFP
+       tristate "SysKonnect FDDI PCI support"
+       depends on FDDI && PCI
+       select BITREVERSE
+       ---help---
+         Say Y here if you have a SysKonnect FDDI PCI adapter.
+         The following adapters are supported by this driver:
+         - SK-5521 (SK-NET FDDI-UP)
+         - SK-5522 (SK-NET FDDI-UP DAS)
+         - SK-5541 (SK-NET FDDI-FP)
+         - SK-5543 (SK-NET FDDI-LP)
+         - SK-5544 (SK-NET FDDI-LP DAS)
+         - SK-5821 (SK-NET FDDI-UP64)
+         - SK-5822 (SK-NET FDDI-UP64 DAS)
+         - SK-5841 (SK-NET FDDI-FP64)
+         - SK-5843 (SK-NET FDDI-LP64)
+         - SK-5844 (SK-NET FDDI-LP64 DAS)
+         - Netelligent 100 FDDI DAS Fibre SC
+         - Netelligent 100 FDDI SAS Fibre SC
+         - Netelligent 100 FDDI DAS UTP
+         - Netelligent 100 FDDI SAS UTP
+         - Netelligent 100 FDDI SAS Fibre MIC
+
+         Read <file:Documentation/networking/skfp.txt> for information about
+         the driver.
+
+         Questions concerning this driver can be addressed to:
+         <linux@syskonnect.de>
+
+         To compile this driver as a module, choose M here: the module
+         will be called skfp.  This is recommended.
+
+endif # FDDI