if (reg & (FM10K_DMA_CTRL_TX_ACTIVE | FM10K_DMA_CTRL_RX_ACTIVE))
return FM10K_ERR_DMA_PENDING;
+ /* verify the switch is ready for reset */
+ reg = fm10k_read_reg(hw, FM10K_DMA_CTRL2);
+ if (!(reg & FM10K_DMA_CTRL2_SWITCH_READY))
+ goto out;
+
/* Inititate data path reset */
reg |= FM10K_DMA_CTRL_DATAPATH_RESET;
fm10k_write_reg(hw, FM10K_DMA_CTRL, reg);
if (!(reg & FM10K_IP_NOTINRESET))
err = FM10K_ERR_RESET_FAILED;
+out:
return err;
}
return 0;
}
-/**
- * fm10k_is_slot_appropriate_pf - Indicate appropriate slot for this SKU
- * @hw: pointer to hardware structure
- *
- * Looks at the PCIe bus info to confirm whether or not this slot can support
- * the necessary bandwidth for this device.
- **/
-static bool fm10k_is_slot_appropriate_pf(struct fm10k_hw *hw)
-{
- return (hw->bus.speed == hw->bus_caps.speed) &&
- (hw->bus.width == hw->bus_caps.width);
-}
-
/**
* fm10k_update_vlan_pf - Update status of VLAN ID in VLAN filter table
* @hw: pointer to hardware structure
fm10k_write_reg(hw, FM10K_RQMAP(qmap_idx + i), vf_q_idx + i);
}
+ /* repeat the first ring for all the remaining VF rings */
+ for (i = queues_per_pool; i < qmap_stride; i++) {
+ fm10k_write_reg(hw, FM10K_TQMAP(qmap_idx + i), vf_q_idx);
+ fm10k_write_reg(hw, FM10K_RQMAP(qmap_idx + i), vf_q_idx);
+ }
+
return 0;
}
return hw->iov.ops.assign_int_moderator(hw, vf_idx);
}
+/**
+ * fm10k_iov_select_vid - Select correct default VID
+ * @hw: Pointer to hardware structure
+ * @vid: VID to correct
+ *
+ * Will report an error if VID is out of range. For VID = 0, it will return
+ * either the pf_vid or sw_vid depending on which one is set.
+ */
+static inline s32 fm10k_iov_select_vid(struct fm10k_vf_info *vf_info, u16 vid)
+{
+ if (!vid)
+ return vf_info->pf_vid ? vf_info->pf_vid : vf_info->sw_vid;
+ else if (vf_info->pf_vid && vid != vf_info->pf_vid)
+ return FM10K_ERR_PARAM;
+ else
+ return vid;
+}
+
/**
* fm10k_iov_msg_mac_vlan_pf - Message handler for MAC/VLAN request from VF
* @hw: Pointer to hardware structure
struct fm10k_mbx_info *mbx)
{
struct fm10k_vf_info *vf_info = (struct fm10k_vf_info *)mbx;
- int err = 0;
u8 mac[ETH_ALEN];
u32 *result;
+ int err = 0;
+ bool set;
u16 vlan;
u32 vid;
if (err)
return err;
- /* if VLAN ID is 0, set the default VLAN ID instead of 0 */
- if (!vid || (vid == FM10K_VLAN_CLEAR)) {
- if (vf_info->pf_vid)
- vid |= vf_info->pf_vid;
- else
- vid |= vf_info->sw_vid;
- } else if (vid != vf_info->pf_vid) {
+ /* verify upper 16 bits are zero */
+ if (vid >> 16)
return FM10K_ERR_PARAM;
- }
+
+ set = !(vid & FM10K_VLAN_CLEAR);
+ vid &= ~FM10K_VLAN_CLEAR;
+
+ err = fm10k_iov_select_vid(vf_info, vid);
+ if (err < 0)
+ return err;
+ else
+ vid = err;
/* update VSI info for VF in regards to VLAN table */
- err = hw->mac.ops.update_vlan(hw, vid, vf_info->vsi,
- !(vid & FM10K_VLAN_CLEAR));
+ err = hw->mac.ops.update_vlan(hw, vid, vf_info->vsi, set);
}
if (!err && !!results[FM10K_MAC_VLAN_MSG_MAC]) {
memcmp(mac, vf_info->mac, ETH_ALEN))
return FM10K_ERR_PARAM;
- /* if VLAN ID is 0, set the default VLAN ID instead of 0 */
- if (!vlan || (vlan == FM10K_VLAN_CLEAR)) {
- if (vf_info->pf_vid)
- vlan |= vf_info->pf_vid;
- else
- vlan |= vf_info->sw_vid;
- } else if (vf_info->pf_vid) {
- return FM10K_ERR_PARAM;
- }
+ set = !(vlan & FM10K_VLAN_CLEAR);
+ vlan &= ~FM10K_VLAN_CLEAR;
+
+ err = fm10k_iov_select_vid(vf_info, vlan);
+ if (err < 0)
+ return err;
+ else
+ vlan = err;
/* notify switch of request for new unicast address */
- err = hw->mac.ops.update_uc_addr(hw, vf_info->glort, mac, vlan,
- !(vlan & FM10K_VLAN_CLEAR), 0);
+ err = hw->mac.ops.update_uc_addr(hw, vf_info->glort,
+ mac, vlan, set, 0);
}
if (!err && !!results[FM10K_MAC_VLAN_MSG_MULTICAST]) {
if (!(vf_info->vf_flags & FM10K_VF_FLAG_MULTI_ENABLED))
return FM10K_ERR_PARAM;
- /* if VLAN ID is 0, set the default VLAN ID instead of 0 */
- if (!vlan || (vlan == FM10K_VLAN_CLEAR)) {
- if (vf_info->pf_vid)
- vlan |= vf_info->pf_vid;
- else
- vlan |= vf_info->sw_vid;
- } else if (vf_info->pf_vid) {
- return FM10K_ERR_PARAM;
- }
+ set = !(vlan & FM10K_VLAN_CLEAR);
+ vlan &= ~FM10K_VLAN_CLEAR;
+
+ err = fm10k_iov_select_vid(vf_info, vlan);
+ if (err < 0)
+ return err;
+ else
+ vlan = err;
/* notify switch of request for new multicast address */
- err = hw->mac.ops.update_mc_addr(hw, vf_info->glort, mac, vlan,
- !(vlan & FM10K_VLAN_CLEAR));
+ err = hw->mac.ops.update_mc_addr(hw, vf_info->glort,
+ mac, vlan, set);
}
return err;
err = fm10k_update_lport_state_pf(hw, vf_info->glort,
1, false);
+ /* we need to clear VF_FLAG_ENABLED flags in order to ensure
+ * that we actually re-enable the LPORT state below. Note that
+ * this has no impact if the VF is already disabled, as the
+ * flags are already cleared.
+ */
+ if (!err)
+ vf_info->vf_flags = FM10K_VF_FLAG_CAPABLE(vf_info);
+
/* when enabling the port we should reset the rate limiters */
hw->iov.ops.configure_tc(hw, vf_info->vf_idx, vf_info->rate);
if (systime_adjust > FM10K_SW_SYSTIME_ADJUST_MASK)
return FM10K_ERR_PARAM;
- if (ppb < 0)
- systime_adjust |= FM10K_SW_SYSTIME_ADJUST_DIR_NEGATIVE;
+ if (ppb > 0)
+ systime_adjust |= FM10K_SW_SYSTIME_ADJUST_DIR_POSITIVE;
fm10k_write_sw_reg(hw, FM10K_SW_SYSTIME_ADJUST, (u32)systime_adjust);
.init_hw = &fm10k_init_hw_pf,
.start_hw = &fm10k_start_hw_generic,
.stop_hw = &fm10k_stop_hw_generic,
- .is_slot_appropriate = &fm10k_is_slot_appropriate_pf,
.update_vlan = &fm10k_update_vlan_pf,
.read_mac_addr = &fm10k_read_mac_addr_pf,
.update_uc_addr = &fm10k_update_uc_addr_pf,
Code Review / kvmfornfv.git / blobdiff